diff options
Diffstat (limited to 'src/mainboard/artecgroup')
| -rw-r--r-- | src/mainboard/artecgroup/dbe61/Config.lb | 128 | ||||
| -rw-r--r-- | src/mainboard/artecgroup/dbe61/Options.lb | 19 | ||||
| -rw-r--r-- | src/mainboard/artecgroup/dbe61/auto.c | 134 | ||||
| -rw-r--r-- | src/mainboard/artecgroup/dbe61/cache_as_ram_auto.c | 215 | ||||
| -rw-r--r-- | src/mainboard/artecgroup/dbe61/irq_tables.c | 141 | ||||
| -rw-r--r-- | src/mainboard/artecgroup/dbe61/mainboard.c | 30 | ||||
| -rw-r--r-- | src/mainboard/artecgroup/dbe61/spd_table.h | 53 |
7 files changed, 446 insertions, 274 deletions
diff --git a/src/mainboard/artecgroup/dbe61/Config.lb b/src/mainboard/artecgroup/dbe61/Config.lb index 97975e7c36..40f157f6e9 100644 --- a/src/mainboard/artecgroup/dbe61/Config.lb +++ b/src/mainboard/artecgroup/dbe61/Config.lb @@ -47,27 +47,17 @@ driver mainboard.o if HAVE_PIRQ_TABLE object irq_tables.o end #object reset.o -## -## Romcc output -## -makerule ./failover.E - depends "$(MAINBOARD)/failover.c ./romcc" - action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" -end -makerule ./failover.inc - depends "$(MAINBOARD)/failover.c ./romcc" - action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" +if USE_DCACHE_RAM + #compile cache_as_ram.c to auto.inc + makerule ./cache_as_ram_auto.inc + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@" + action "perl -e 's/.rodata/.rom.data/g' -pi $@" + action "perl -e 's/.text/.section .rom.text/g' -pi $@" + end end -makerule ./auto.E - depends "$(MAINBOARD)/auto.c option_table.h ./romcc" - action "./romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" -end -makerule ./auto.inc - depends "$(MAINBOARD)/auto.c option_table.h ./romcc" - action "./romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" -end ## ## Build our 16 bit and 32 bit linuxBIOS entry code @@ -104,7 +94,7 @@ ldscript /arch/i386/lib/id.lds ### if USE_FALLBACK_IMAGE ldscript /arch/i386/lib/failover.lds - mainboardinit ./failover.inc +# mainboardinit ./failover.inc end ### @@ -115,7 +105,11 @@ end ## Setup RAM ## mainboardinit cpu/x86/fpu/enable_fpu.inc -mainboardinit ./auto.inc + +if USE_DCACHE_RAM + mainboardinit cpu/amd/model_lx/cache_as_ram.inc + mainboardinit ./cache_as_ram_auto.inc +end ## ## Include the secondary Configuration files @@ -124,70 +118,44 @@ dir /pc80 config chip.h chip northbridge/amd/lx - register "irqmap" = "0xcba5" + device pci_domain 0 on + device pci 1.0 on end # Northbridge + device pci 1.1 on end # Graphics + chip southbridge/amd/cs5536 + # IRQ 12 and 1 unmasked, Keyboard and Mouse IRQs. OK + # SIRQ Mode = Active(Quiet) mode. Save power.... + # Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK + register "lpc_serirq_enable" = "0x00001002" + register "lpc_serirq_polarity" = "0x0000EFFD" + register "lpc_serirq_mode" = "1" + register "enable_gpio_int_route" = "0x0D0C0700" + register "enable_ide_nand_flash" = "0" # 0:ide mode, 1:flash + register "enable_USBP4_device" = "0" #0: host, 1:device + register "enable_USBP4_overcurrent" = "0" #0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381) + register "com1_enable" = "0" + register "com1_address" = "0x2F8" + register "com1_irq" = "3" + register "com2_enable" = "1" + register "com2_address" = "0x3F8" + register "com2_irq" = "4" + register "unwanted_vpci[0]" = "0" # End of list has a zero + device pci b.0 on end # Slot 3 + device pci c.0 on end # Slot 4 + device pci d.0 on end # Slot 1 + device pci e.0 on end # Slot 2 + device pci f.0 on end # ISA Bridge + device pci f.2 on end # IDE Controller + device pci f.3 on end # Audio + device pci f.4 on end # OHCI + device pci f.5 on end # EHCI + end + end + # APIC cluster is late CPU init. device apic_cluster 0 on chip cpu/amd/model_lx device apic 0 on end end end - device pci_domain 0 on - - device pci 1.0 on end # Host Bridge - -# chip drivers/pci/realmode -# device pci 1.1 on end # VGA -# register "rom_address" = "0xfffc0000" # at the beginning of 256k -# end - - device pci 1.2 off end # AES - chip southbridge/amd/cs5536_lx - register "enable_ide_nand_flash" = "0" - - register "isa_irq" = "0" - #register "flash_irq" = "14" - - ## IDE IRQ - register "enable_ide_irq" = "0" - - register "audio_irq" = "5" - register "usb_irq" = "7" - - register "uart0_irq" = "0" - register "uart1_irq" = "4" - - ## PCI INTA ... INTD and their GPIO pins - ## int==0: disable - register "pci_int[0]" = "0" - register "pci_int[1]" = "10" - register "pci_int[2]" = "0" - register "pci_int[3]" = "0" - register "pci_int_pin[0]" = "0" - register "pci_int_pin[1]" = "7" - register "pci_int_pin[2]" = "0" - register "pci_int_pin[3]" = "0" - - - # Keyboard Emulation Logic IRQs - # Enable keyboard IRQ2 - register "enable_kel_keyb_irq" = "0" - # Enable mouse IRQ12 - register "enable_kel_mouse_irq" = "0" - # Configure KEL Emulation IRQ, 0 to disable - register "kel_emul_irq" = "0" - - device pci f.0 on end # ISA Bridge - device pci f.1 on end # Flash controller - device pci f.2 off end # IDE controller - device pci f.3 on end # Audio - device pci f.4 on end # OHCI - device pci f.5 on end # EHCI - device pci f.6 off end # UDC controller - device pci f.7 off end # OTG controller - end -# chip drivers/pci/rtl8139 -## device pci d.0 on end # Realtek LAN -# register "nic_irq" = "10" -# end - end + end diff --git a/src/mainboard/artecgroup/dbe61/Options.lb b/src/mainboard/artecgroup/dbe61/Options.lb index 382f3bdda7..3f773af79c 100644 --- a/src/mainboard/artecgroup/dbe61/Options.lb +++ b/src/mainboard/artecgroup/dbe61/Options.lb @@ -23,6 +23,7 @@ uses ROM_SECTION_OFFSET uses CONFIG_ROM_PAYLOAD_START uses CONFIG_COMPRESSED_PAYLOAD_LZMA uses CONFIG_COMPRESSED_PAYLOAD_NRV2B +uses CONFIG_PRECOMPRESSED_PAYLOAD uses PAYLOAD_SIZE uses _ROMBASE uses _RAMBASE @@ -44,6 +45,9 @@ uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 uses CONFIG_CONSOLE_VGA uses CONFIG_PCI_ROM_RUN uses CONFIG_VIDEO_MB +uses USE_DCACHE_RAM +uses DCACHE_RAM_BASE +uses DCACHE_RAM_SIZE ## ROM_SIZE is the size of boot ROM that this board will use. default ROM_SIZE = 256*1024 @@ -51,8 +55,8 @@ default ROM_SIZE = 256*1024 ### ### Build options ### -default CONFIG_CONSOLE_VGA=1 -default CONFIG_PCI_ROM_RUN=1 +default CONFIG_CONSOLE_VGA=0 +default CONFIG_PCI_ROM_RUN=0 default CONFIG_VIDEO_MB=8 ## @@ -78,8 +82,8 @@ default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 ## ## Build code to export a programmable irq routing table ## -default HAVE_PIRQ_TABLE=0 -default IRQ_SLOT_COUNT=6 +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=3 #object irq_tables.o @@ -97,6 +101,13 @@ default ROM_IMAGE_SIZE = 65536 default FALLBACK_SIZE = 131072 ## +## enable CACHE_AS_RAM specifics +## +default USE_DCACHE_RAM=1 +default DCACHE_RAM_BASE=0xc8000 +default DCACHE_RAM_SIZE=0x08000 + +## ## Use a small 8K stack ## default STACK_SIZE=0x2000 diff --git a/src/mainboard/artecgroup/dbe61/auto.c b/src/mainboard/artecgroup/dbe61/auto.c deleted file mode 100644 index 1dba629381..0000000000 --- a/src/mainboard/artecgroup/dbe61/auto.c +++ /dev/null @@ -1,134 +0,0 @@ -#define ASSEMBLY 1 - -#include <stdint.h> -#include <device/pci_def.h> -#include <arch/io.h> -#include <device/pnp_def.h> -#include <arch/romcc_io.h> -#include <arch/hlt.h> -#include "pc80/serial.c" -#include "arch/i386/lib/console.c" -#include "ram/ramtest.c" -//#include "superio/winbond/w83627hf/w83627hf_early_serial.c" -#include "cpu/x86/bist.h" -#include "cpu/x86/msr.h" -#include <cpu/amd/lxdef.h> - -//#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1) - -#include "southbridge/amd/cs5536/cs5536_early_smbus.c" -#include "southbridge/amd/cs5536/cs5536_early_setup.c" - -static inline int spd_read_byte(unsigned device, unsigned address) -{ - return smbus_read_byte(device, address); -} - -#include "northbridge/amd/lx/raminit.h" - -static inline unsigned int fls(unsigned int x) -{ - int r; - - __asm__("bsfl %1,%0\n\t" - "jnz 1f\n\t" - "movl $32,%0\n" - "1:" : "=r" (r) : "g" (x)); - return r; -} - -static void sdram_set_spd_registers(const struct mem_controller *ctrl) -{ - /* Total size of DIMM = 2^row address (byte 3) * 2^col address (byte 4) * - * component Banks (byte 17) * module banks, side (byte 5) * - * width in bits (byte 6,7) - * = Density per side (byte 31) * number of sides (byte 5) */ - /* 1. Initialize GLMC registers base on SPD values, do one DIMM for now */ - msr_t msr; - unsigned char module_banks, val; - - msr.hi = 0x10075012; - msr.lo = 0x00000040; - - wrmsr(MC_CF07_DATA, msr); //GX3 - - /* timing and mode ... */ - - //msr = rdmsr(0x20000019); - - /* per standard bios settings */ -/* - msr.hi = 0x18000108; - msr.lo = - (6<<28) | // cas_lat - (10<<24)| // ref2act - (7<<20)| // act2pre - (3<<16)| // pre2act - (3<<12)| // act2cmd - (2<<8)| // act2act - (2<<6)| // dplwr - (2<<4)| // dplrd - (3); // dal - * the msr value reported by quanta is very, very different. - * we will go with that value for now. - * - //msr.lo = 0x286332a3; -*/ - //wrmsr(0x20000019, msr); //GX3 - -} - -#include "northbridge/amd/lx/raminit.c" -#include "sdram/generic_sdram.c" - -/* CPU and GLIU mult/div */ -#define PLLMSRhi 0x0000039C -/* Hold Count - how long we will sit in reset */ -#define PLLMSRlo 0x00DE0000 - -#include "northbridge/amd/lx/pll_reset.c" -#include "cpu/amd/model_lx/cpureginit.c" -#include "cpu/amd/model_lx/syspreinit.c" - -static void msr_init(void) -{ - __builtin_wrmsr(0x10000020, 0xfff80, 0x20000000); - __builtin_wrmsr(0x10000021, 0x80fffe0, 0x20000000); - - __builtin_wrmsr(0x40000020, 0xfff80, 0x20000000); - __builtin_wrmsr(0x40000021, 0x80fffe0, 0x20000000); -} - - -static void main(unsigned long bist) -{ - static const struct mem_controller memctrl [] = { - {.channel0 = {(0xa<<3)|0, (0xa<<3)|1}} - }; - - SystemPreInit(); //GX3 OK - - msr_init(); //GX3 OK - - cs5536_early_setup(); //GX3 OK - - /* NOTE: must do this AFTER the early_setup! - * it is counting on some early MSR setup - * for cs5536 - */ - cs5536_setup_onchipuart(); //GX3 OK - - uart_init(); //GX3 OK - console_init(); //GX3 OK - - pll_reset(); //GX3 OK - - cpuRegInit(); //GX3 OK - - print_err("done cpuRegInit\n"); - - sdram_initialize(1, memctrl); //GX3 OK almost - - /* Check all of memory */ - //ram_check(0x00000000, 640*1024); -} diff --git a/src/mainboard/artecgroup/dbe61/cache_as_ram_auto.c b/src/mainboard/artecgroup/dbe61/cache_as_ram_auto.c new file mode 100644 index 0000000000..e0b51b1770 --- /dev/null +++ b/src/mainboard/artecgroup/dbe61/cache_as_ram_auto.c @@ -0,0 +1,215 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2007 Advanced Micro Devices, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#define ASSEMBLY 1 + +#include <stdint.h> +#include <device/pci_def.h> +#include <arch/io.h> +#include <device/pnp_def.h> +#include <arch/romcc_io.h> +#include <arch/hlt.h> +#include "pc80/serial.c" +#include "arch/i386/lib/console.c" +#include "ram/ramtest.c" +#include "cpu/x86/bist.h" +#include "cpu/x86/msr.h" +#include <cpu/amd/lxdef.h> +#include <cpu/amd/geode_post_code.h> +#include "southbridge/amd/cs5536/cs5536.h" +#include "spd_table.h" + + +#define POST_CODE(x) outb(x, 0x80) + +#include "southbridge/amd/cs5536/cs5536_early_smbus.c" +#include "southbridge/amd/cs5536/cs5536_early_setup.c" + +#define DIMM0 0xA0 +#define DIMM1 0xA2 + + +static int spd_read_byte(unsigned device, unsigned address) +{ + int i; + + if (device == DIMM0){ + for (i=0; i < (sizeof spd_table/sizeof spd_table[0]); i++){ + if (spd_table[i].address == address){ + return spd_table[i].data; + } + } + } + + /* returns 0xFF on any failures */ + return 0xFF; +} + +#define ManualConf 0 /* Do automatic strapped PLL config */ +/* CPU and GLIU mult/div 500/266*/ +#define PLLMSRhi 0x0000039C /* 33MHz PCI, 0x000003DD for 66MHz PCI */ +/* Hold Count - how long we will sit in reset */ +#define PLLMSRlo 0x00DE6000 + +#include "northbridge/amd/lx/raminit.h" +#include "northbridge/amd/lx/pll_reset.c" +#include "northbridge/amd/lx/raminit.c" +#include "sdram/generic_sdram.c" +#include "cpu/amd/model_lx/cpureginit.c" +#include "cpu/amd/model_lx/syspreinit.c" + +static void msr_init(void) +{ + msr_t msr; + /* Setup access to the cache for under 1MB. */ + msr.hi = 0x24fffc02; + msr.lo = 0x1000A000; /* 0-A0000 write back */ + wrmsr(CPU_RCONF_DEFAULT, msr); + + msr.hi = 0x0; /* write back */ + msr.lo = 0x0; + wrmsr(CPU_RCONF_A0_BF, msr); + wrmsr(CPU_RCONF_C0_DF, msr); + wrmsr(CPU_RCONF_E0_FF, msr); + + /* Setup access to the cache for under 640K. Note MC not setup yet. */ + msr.hi = 0x20000000; + msr.lo = 0xfff80; + wrmsr(MSR_GLIU0 + 0x20, msr); + + msr.hi = 0x20000000; + msr.lo = 0x80fffe0; + wrmsr(MSR_GLIU0 + 0x21, msr); + + msr.hi = 0x20000000; + msr.lo = 0xfff80; + wrmsr(MSR_GLIU1 + 0x20, msr); + + msr.hi = 0x20000000; + msr.lo = 0x80fffe0; + wrmsr(MSR_GLIU1 + 0x21, msr); + +} + +static void mb_gpio_init(void) +{ + /* Early mainboard specific GPIO setup */ +} + +static void cs5536_setup_onchipuart2(void) +{ + msr_t msr; + + /* GPIO4 - UART2_TX */ + /* Set: Output Enable (0x4) */ + outl(GPIOL_4_SET, GPIO_IO_BASE + GPIOL_OUTPUT_ENABLE); + /* Set: OUTAUX1 Select (0x10) */ + outl(GPIOL_4_SET, GPIO_IO_BASE + GPIOL_OUT_AUX1_SELECT); + /* GPIO4 - UART2_RX */ + /* Set: Input Enable (0x20) */ + outl(GPIOL_3_SET, GPIO_IO_BASE + GPIOL_INPUT_ENABLE); + /* Set: INAUX1 Select (0x34) */ + outl(GPIOL_3_SET, GPIO_IO_BASE + GPIOL_IN_AUX1_SELECT); + + /* Set: GPIO 3 + 3 Pull Up (0x18) */ + outl(GPIOL_3_SET | GPIOL_4_SET, GPIO_IO_BASE + GPIOL_PULLUP_ENABLE); + + /* set address to 3F8 */ + msr = rdmsr(MDD_LEG_IO); + msr.lo |= 0x7 << 20; + wrmsr(MDD_LEG_IO, msr); + + /* Bit 1 = DEVEN (device enable) + * Bit 4 = EN_BANKS (allow access to the upper banks + */ + msr.lo = (1 << 4) | (1 << 1); + msr.hi = 0; + + /* enable COM2 */ + wrmsr(MDD_UART2_CONF, msr); +} + +void cache_as_ram_main(void) +{ + POST_CODE(0x01); + + static const struct mem_controller memctrl[] = { + {.channel0 = {(0xa << 3) | 0, (0xa << 3) | 1}} + }; + + SystemPreInit(); + msr_init(); + + cs5536_early_setup(); + + /* NOTE: must do this AFTER the early_setup! + * it is counting on some early MSR setup + * for cs5536 + */ + /* cs5536_disable_internal_uart disable them. Set them up now... */ + cs5536_setup_onchipuart2(); /* dbe61 uses UART2 as COM1 */ + mb_gpio_init(); + uart_init(); + console_init(); + + pll_reset(ManualConf); + + cpuRegInit(); + + sdram_initialize(1, memctrl); + + /* Dump memory configuratation */ + /*{ + msr_t msr; + msr = rdmsr(MC_CF07_DATA); + print_debug("MC_CF07_DATA: "); + print_debug_hex32(MC_CF07_DATA); + print_debug(" value is: "); + print_debug_hex32(msr.hi); + print_debug(":"); + print_debug_hex32(msr.lo); + print_debug(" \n"); + + msr = rdmsr(MC_CF1017_DATA); + print_debug("MC_CF1017_DATA: "); + print_debug_hex32(MC_CF1017_DATA); + print_debug(" value is: "); + print_debug_hex32(msr.hi); + print_debug(":"); + print_debug_hex32(msr.lo); + print_debug(" \n"); + + msr = rdmsr(MC_CF8F_DATA); + print_debug("MC_CF8F_DATA: "); + print_debug_hex32(MC_CF8F_DATA); + print_debug(" value is: "); + print_debug_hex32(msr.hi); + print_debug(":"); + print_debug_hex32(msr.lo); + msr = rdmsr(MC_CF8F_DATA); + print_debug(" \n"); + }*/ + + /* Check memory. */ + /* ram_check(0x00000000, 640 * 1024); */ + + /* Memory is setup. Return to cache_as_ram.inc and continue to boot */ + return; +} diff --git a/src/mainboard/artecgroup/dbe61/irq_tables.c b/src/mainboard/artecgroup/dbe61/irq_tables.c index 4322e20e9b..07ded9d386 100644 --- a/src/mainboard/artecgroup/dbe61/irq_tables.c +++ b/src/mainboard/artecgroup/dbe61/irq_tables.c @@ -1,60 +1,105 @@ -/* This file was generated by getpir.c, do not modify! - (but if you do, please run checkpir on it to verify) - * Contains the IRQ Routing Table dumped directly from your memory, which BIOS sets up +/* + * This file is part of the LinuxBIOS project. * - * Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM -*/ + * Copyright (C) 2007 Advanced Micro Devices, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ #include <arch/pirq_routing.h> +#include <console/console.h> +#include <arch/io.h> +#include <arch/pirq_routing.h> +#include "../../../southbridge/amd/cs5536/cs5536.h" -#define ID_SLOT_PCI_NET 1 // ThinCan ethernet -#define ID_SLOT_PCI_RSVD1 2 // reserved entry 1 -#define ID_SLOT_PCI_RSVD3 3 // reserved entry 2 -#define ID_SLOT_PCI_RSVD2 4 // reserved entry 3 -#define ID_EMBED_PCI 0xff // onboard PCI device +/* Platform IRQs */ +#define PIRQA 10 +#define PIRQB 11 +#define PIRQC 10 +#define PIRQD 11 -// CS5535 PCI INT[A-D] Interrupt Routing lines. -#define NO_CONNECT 0 // not used -#define CS_PCI_INTA 1 // PCI INTA -#define CS_PCI_INTB 2 // PCI INTB -#define CS_PCI_INTC 3 // PCI INTC -#define CS_PCI_INTD 4 // PCI INTD +/* Map */ +#define M_PIRQA (1 << PIRQA) /* Bitmap of supported IRQs */ +#define M_PIRQB (1 << PIRQB) /* Bitmap of supported IRQs */ +#define M_PIRQC (1 << PIRQC) /* Bitmap of supported IRQs */ +#define M_PIRQD (1 << PIRQD) /* Bitmap of supported IRQs */ -// IRQ bitmap reference line FEDCBA9876543210 -// 0000110000100000b -#define PCI_IRQ 0xc20 // PCI allowed IRQs here +/* Link */ +#define L_PIRQA 1 /* Means Slot INTx# Connects To Chipset INTA# */ +#define L_PIRQB 2 /* Means Slot INTx# Connects To Chipset INTB# */ +#define L_PIRQC 3 /* Means Slot INTx# Connects To Chipset INTC# */ +#define L_PIRQD 4 /* Means Slot INTx# Connects To Chipset INTD# */ -const struct irq_routing_table intel_irq_routing_table = -{ - PIRQ_SIGNATURE, /* u32 signature */ - PIRQ_VERSION, /* u16 version */ - 32+16*6, /* there can be total 2 devices on the bus */ - 0x00, /* Where the interrupt router lies (bus) */ - (0x12<<3)|0x0, /* Where the interrupt router lies (dev) */ - 0x0800, /* IRQs devoted exclusively to PCI usage */ - 0x1022, /* Vendor */ - 0x208f, /* Device */ - 0x00000000, /* Crap (miniport) */ - { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */ - 0xdf, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ +const struct irq_routing_table intel_irq_routing_table = { + PIRQ_SIGNATURE, /* u32 signature */ + PIRQ_VERSION, /* u16 version */ + 32 + 16 * IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */ + 0x00, /* Where the interrupt router lies (bus) */ + (0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */ + 0x00, /* IRQs devoted exclusively to PCI usage */ + 0x100B, /* Vendor */ + 0x002B, /* Device */ + 0, /* Crap (miniport) */ + {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */ + 0x00, /* u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ { - /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */ - // Geode GX3 Host Bridge and VGA Graphics - {0, 0x01<<3, {{CS_PCI_INTA, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}}, ID_EMBED_PCI, 0x0}, - // Realtek RTL8100/8139 Network Controller - {0, 0x0d<<3, {{CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}}, ID_SLOT_PCI_NET, 0x0}, - // Reserved for future extensions - {0, 0x0c<<3, {{CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}}, ID_SLOT_PCI_RSVD1, 0x0}, - // Geode CS5535/CS5536 IO Companion: USB controllers, IDE, Audio. - {0, 0x0f<<3, {{CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}}, ID_EMBED_PCI, 0x0}, - // Reserved for future extensions - {0, 0x0e<<3, {{CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}}, ID_SLOT_PCI_RSVD2, 0x0}, - // Reserved for future extensions - {0, 0x0b<<3, {{CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}}, ID_SLOT_PCI_RSVD3, 0x0} - } + /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */ + /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */ + {0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* cpu */ + {0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */ + {0x00, (0x0D << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* ethernet */ + } }; unsigned long write_pirq_routing_table(unsigned long addr) { - return copy_pirq_routing_table(addr); -} + int i, j, k, num_entries; + unsigned char pirq[4]; + uint16_t chipset_irq_map; + uint32_t pciAddr, pirtable_end; + struct irq_routing_table *pirq_tbl; + + pirtable_end = copy_pirq_routing_table(addr); + + /* Set up chipset IRQ steering. */ + pciAddr = 0x80000000 | (CHIPSET_DEV_NUM << 11) | 0x5C; + chipset_irq_map = (PIRQD << 12 | PIRQC << 8 | PIRQB << 4 | PIRQA); + printk_debug("%s(%08X, %04X)\n", __FUNCTION__, pciAddr, + chipset_irq_map); + outl(pciAddr & ~3, 0xCF8); + outl(chipset_irq_map, 0xCFC); + + pirq_tbl = (struct irq_routing_table *)(addr); + num_entries = (pirq_tbl->size - 32) / 16; + + /* Set PCI IRQs. */ + for (i = 0; i < num_entries; i++) { + printk_debug("PIR Entry %d Dev/Fn: %X Slot: %d\n", i, + pirq_tbl->slots[i].devfn, pirq_tbl->slots[i].slot); + for (j = 0; j < 4; j++) { + printk_debug("INT: %c bitmap: %x ", 'A' + j, + pirq_tbl->slots[i].irq[j].bitmap); + for (k = 0; (!((pirq_tbl->slots[i].irq[j].bitmap >> k) & 1)) && (pirq_tbl->slots[i].irq[j].bitmap != 0); k++) ; /* Finds lsb in bitmap to IRQ#. */ + pirq[j] = k; + printk_debug("PIRQ: %d\n", k); + } + + /* Bus, device, slots IRQs for {A,B,C,D}. */ + pci_assign_irqs(pirq_tbl->slots[i].bus, + pirq_tbl->slots[i].devfn >> 3, pirq); + } + + /* Put the PIR table in memory and checksum. */ + return pirtable_end; +}
\ No newline at end of file diff --git a/src/mainboard/artecgroup/dbe61/mainboard.c b/src/mainboard/artecgroup/dbe61/mainboard.c index 0476400de0..ba60b53f64 100644 --- a/src/mainboard/artecgroup/dbe61/mainboard.c +++ b/src/mainboard/artecgroup/dbe61/mainboard.c @@ -1,3 +1,22 @@ +/* +* This file is part of the LinuxBIOS project. +* +* Copyright (C) 2007 Advanced Micro Devices +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + #include <console/console.h> #include <device/device.h> #include <device/pci.h> @@ -6,20 +25,15 @@ #include <arch/io.h> #include <cpu/x86/msr.h> #include <cpu/amd/lxdef.h> +#include "../../../southbridge/amd/cs5536/cs5536.h" #include "chip.h" -#define DIVIL_LBAR_GPIO 0x5140000c - static void init_gpio() { msr_t msr; - printk_debug("Initializing GPIO module...\n"); + printk_debug("Checking GPIO module...\n"); - // initialize the GPIO LBAR - msr.lo = GPIO_BASE; - msr.hi = 0x0000f001; - wrmsr(DIVIL_LBAR_GPIO, msr); - msr = rdmsr(DIVIL_LBAR_GPIO); + msr = rdmsr(MDD_LBAR_GPIO); printk_debug("DIVIL_LBAR_GPIO set to 0x%08x 0x%08x\n", msr.hi, msr.lo); } diff --git a/src/mainboard/artecgroup/dbe61/spd_table.h b/src/mainboard/artecgroup/dbe61/spd_table.h new file mode 100644 index 0000000000..00b6e7da10 --- /dev/null +++ b/src/mainboard/artecgroup/dbe61/spd_table.h @@ -0,0 +1,53 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2007 Advanced Micro Devices, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <spd.h> + +struct spd_entry { + unsigned int address; + unsigned int data; + }; + +/* Save space by using a short list of SPD values used by Geode LX Memory init */ +/* 128MB */ +const struct spd_entry spd_table [] = +{ +{SPD_MEMORY_TYPE, 0x07}, /* (Fundamental) memory type */ +{SPD_NUM_ROWS, 0x0D}, /* Number of row address bits */ +{SPD_NUM_COLUMNS, 0x09}, /* Number of column address bits */ +{SPD_NUM_DIMM_BANKS, 0x01}, /* Number of module rows (banks) */ +{SPD_MIN_CYCLE_TIME_AT_CAS_MAX, 0x50}, /* SDRAM cycle time (highest CAS latency), RAS access time (tRAC) */ +{SPD_REFRESH, 0x82}, /* Refresh rate/type */ +{SPD_PRIMARY_SDRAM_WIDTH, 0x08}, /* SDRAM width (primary SDRAM) */ +{SPD_NUM_BANKS_PER_SDRAM, 0x04}, /* SDRAM device attributes, number of banks on SDRAM device */ +{SPD_ACCEPTABLE_CAS_LATENCIES, 0x1C}, /* SDRAM device attributes, CAS latency */ +{SPD_MODULE_ATTRIBUTES, 0x20}, /* SDRAM module attributes */ +{SPD_DEVICE_ATTRIBUTES_GENERAL, 0xC0}, /* SDRAM device attributes, general */ +{SPD_SDRAM_CYCLE_TIME_2ND, 0x60}, /* SDRAM cycle time (2nd highest CAS latency) */ +{SPD_SDRAM_CYCLE_TIME_3RD, 0x75}, /* SDRAM cycle time (3rd highest CAS latency) */ +{SPD_MIN_ROW_PRECHARGE_TIME, 0x3C}, /* Minimum row precharge time (Trp) */ +{SPD_MIN_ROWACTIVE_TO_ROWACTIVE, 0x28}, /* Minimum row active to row active (Trrd) */ +{SPD_MIN_RAS_TO_CAS_DELAY, 0x3C}, /* Minimum RAS to CAS delay (Trcd) */ +{SPD_MIN_ACTIVE_TO_PRECHARGE_DELAY, 0x28}, /* Minimum RAS pulse width (Tras) */ +{SPD_DENSITY_OF_EACH_ROW_ON_MODULE, 0x20}, /* Density of each row on module */ +{SPD_CMD_SIGNAL_INPUT_HOLD_TIME, 0x60}, /* Command and address signal input hold time */ +{SPD_tRC, 0x37}, /* SDRAM Device Minimum Active to Active/Auto Refresh Time (tRC) */ +{SPD_tRFC, 0x46} /* SDRAM Device Minimum Auto Refresh to Active/Auto Refresh (tRFC) */ +}; |