diff options
Diffstat (limited to 'src/mainboard/amd/dbm690t/Config.lb')
| -rw-r--r-- | src/mainboard/amd/dbm690t/Config.lb | 302 |
1 files changed, 302 insertions, 0 deletions
diff --git a/src/mainboard/amd/dbm690t/Config.lb b/src/mainboard/amd/dbm690t/Config.lb new file mode 100644 index 0000000000..381b1cc4f7 --- /dev/null +++ b/src/mainboard/amd/dbm690t/Config.lb @@ -0,0 +1,302 @@ +## +## This file is part of the coreboot project. +## +## Copyright (C) 2008 Advanced Micro Devices, Inc. +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; version 2 of the License. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## +## +## + + +## +## Compute the location and size of where this firmware image +## (coreboot plus bootloader) will live in the boot rom chip. +## +if USE_FALLBACK_IMAGE + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) +else + default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) + default ROM_SECTION_OFFSET = 0 +end + +## +## Compute the start location and size size of +## The coreboot bootloader. +## +default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) +default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) + +## +## Compute where this copy of coreboot will start in the boot rom +## +default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE ) + +## +## Compute a range of ROM that can cached to speed up coreboot, +## execution speed. +## +## XIP_ROM_SIZE must be a power of 2. +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE +## +default XIP_ROM_SIZE=65536 +default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) + +arch i386 end + +## +## Build the objects we have code for in this directory. +## + +driver mainboard.o + +#dir /drivers/si/3114 + +if HAVE_MP_TABLE object mptable.o end +if HAVE_PIRQ_TABLE + object get_bus_conf.o + object irq_tables.o +end + +#object reset.o + +if USE_DCACHE_RAM + + if CONFIG_USE_INIT + + makerule ./cache_as_ram_auto.o + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@" + end + + else + + makerule ./cache_as_ram_auto.inc + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@" + action "perl -e 's/.rodata/.rom.data/g' -pi $@" + action "perl -e 's/.text/.section .rom.text/g' -pi $@" + end + + end + +end +## +## Build our 16 bit and 32 bit coreboot entry code +## +mainboardinit cpu/x86/16bit/entry16.inc +mainboardinit cpu/x86/32bit/entry32.inc +ldscript /cpu/x86/16bit/entry16.lds +if USE_DCACHE_RAM + if CONFIG_USE_INIT + ldscript /cpu/x86/32bit/entry32.lds + end + + if CONFIG_USE_INIT + ldscript /cpu/amd/car/cache_as_ram.lds + end +end + +## +## Build our reset vector (This is where coreboot is entered) +## +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds +else + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds +end + +## +## Include an id string (For safe flashing) +## +mainboardinit arch/i386/lib/id.inc +ldscript /arch/i386/lib/id.lds + +if USE_DCACHE_RAM + ## + ## Setup Cache-As-Ram + ## + mainboardinit cpu/amd/car/cache_as_ram.inc +end + +### +### This is the early phase of coreboot startup +### Things are delicate and we test to see if we should +### failover to another image. +### +if USE_FALLBACK_IMAGE + if USE_DCACHE_RAM + ldscript /arch/i386/lib/failover.lds + else + ldscript /arch/i386/lib/failover.lds + mainboardinit ./failover.inc + end +end + +### +### O.k. We aren't just an intermediary anymore! +### + +## +## Setup RAM +## +if USE_DCACHE_RAM + + if CONFIG_USE_INIT + initobject cache_as_ram_auto.o + else + mainboardinit ./cache_as_ram_auto.inc + end + +end + +## +## Include the secondary Configuration files +## +if CONFIG_CHIP_NAME + config chip.h +end + +#The variables belong to mainboard are defined here. +#Define system_memory_size, the total memory on mainboard. + +#Define gpp_configuration, A=0, B=1, C=2, D=3, E=4(default) +#Define vga_rom_address = 0xfff0000 +#Define port_enable, (bit map): GFX(2,3), GPP(4,5,6,7) +#Define gfx_dev2_dev3, 0: a link will never be established on Dev2 or Dev3, +# 1: the system allows a PCIE link to be established on Dev2 or Dev3. +#Define gfx_dual_slot, 0: single slot, 1: dual slot +#Define gfx_lane_reversal, 0: disable lane reversal, 1: enable +#Define gfx_tmds, 0: didn't support TMDS, 1: support +#Define gfx_compliance, 0: didn't support compliance, 1: support +#Define gfx_reconfiguration, 0: short reconfiguration, 1(default): long reconfiguration +#Define gfx_link_width, 0: x16, 1: x1, 2: x2, 3: x4, 4: x8, 5: x12 (not supported), 6: x16 +chip northbridge/amd/amdk8/root_complex + device apic_cluster 0 on + chip cpu/amd/socket_S1G1 + device apic 0 on end + end + end + device pci_domain 0 on + chip northbridge/amd/amdk8 + device pci 18.0 on # southbridge + chip southbridge/amd/rs690 + device pci 0.0 on end # HT 0x7910 + device pci 1.0 on # Internal Graphics P2P bridge 0x7912 + chip drivers/pci/onboard + device pci 5.0 on end # Internal Graphics 0x791F + register "rom_address" = "0xfff00000" + end + end + device pci 2.0 on end # PCIE P2P bridge (external graphics) 0x7913 + device pci 3.0 off end # PCIE P2P bridge 0x791b + device pci 4.0 on end # PCIE P2P bridge 0x1914 + device pci 5.0 on end # PCIE P2P bridge 0x7915 + device pci 6.0 on end # PCIE P2P bridge 0x7916 + device pci 7.0 on end # PCIE P2P bridge 0x7917 + device pci 8.0 off end # NB/SB Link P2P bridge + register "vga_rom_address" = "0xfff00000" + register "gpp_configuration" = "4" + register "port_enable" = "0xfc" + register "gfx_dev2_dev3" = "1" + register "gfx_dual_slot" = "0" + register "gfx_lane_reversal" = "0" + register "gfx_tmds" = "0" + register "gfx_compliance" = "0" + register "gfx_reconfiguration" = "1" + register "gfx_link_width" = "0" + end + chip southbridge/amd/sb600 # it is under NB/SB Link, but on the same pri bus + device pci 12.0 on end # SATA 0x4380 + device pci 13.0 on end # USB 0x4387 + device pci 13.1 on end # USB 0x4388 + device pci 13.2 on end # USB 0x4389 + device pci 13.3 on end # USB 0x438a + device pci 13.4 on end # USB 0x438b + device pci 13.5 on end # USB 2 0x4386 + device pci 14.0 on # SM 0x4385 + chip drivers/generic/generic #dimm 0-0-0 + device i2c 50 on end + end + chip drivers/generic/generic #dimm 0-0-1 + device i2c 51 on end + end + chip drivers/generic/generic #dimm 0-1-0 + device i2c 52 on end + end + chip drivers/generic/generic #dimm 0-1-1 + device i2c 53 on end + end + end # SM + device pci 14.1 on end # IDE 0x438c + device pci 14.2 on end # HDA 0x4383 + device pci 14.3 on # LPC 0x438d + chip superio/ite/it8712f + device pnp 2e.0 off # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 2e.1 on # Com1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.2 off # Com2 + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.3 off # Parallel Port + io 0x60 = 0x378 + irq 0x70 = 7 + end + device pnp 2e.4 off end # EC + device pnp 2e.5 on # Keyboard + io 0x60 = 0x60 + io 0x62 = 0x64 + irq 0x70 = 1 + end + device pnp 2e.6 on # Mouse + irq 0x70 = 12 + end + device pnp 2e.8 off # MIDI + io 0x60 = 0x300 + irq 0x70 = 9 + end + device pnp 2e.9 off # GAME + io 0x60 = 0x220 + end + device pnp 2e.a off end # CIR + end #superio/ite/it8712f + end #LPC + device pci 14.4 on end # PCI 0x4384 + device pci 14.5 on end # ACI 0x4382 + device pci 14.6 on end # MCI 0x438e + register "ide0_enable" = "1" + register "sata0_enable" = "1" + register "hda_viddid" = "0x10ec0882" + end #southbridge/amd/sb600 + end # device pci 18.0 + + device pci 18.0 on end + device pci 18.0 on end + device pci 18.1 on end + device pci 18.2 on end + device pci 18.3 on end + end #northbridge/amd/amdk8 + end #pci_domain +end #northbridge/amd/amdk8/root_complex + |