diff options
Diffstat (limited to 'src/mainboard/Iwill/DK8S2/Config.lb')
| -rw-r--r-- | src/mainboard/Iwill/DK8S2/Config.lb | 162 |
1 files changed, 22 insertions, 140 deletions
diff --git a/src/mainboard/Iwill/DK8S2/Config.lb b/src/mainboard/Iwill/DK8S2/Config.lb index 47400f8559..c28b8d3ca7 100644 --- a/src/mainboard/Iwill/DK8S2/Config.lb +++ b/src/mainboard/Iwill/DK8S2/Config.lb @@ -1,110 +1,3 @@ -uses HAVE_MP_TABLE -uses HAVE_PIRQ_TABLE -uses USE_FALLBACK_IMAGE -uses HAVE_FALLBACK_BOOT -uses HAVE_HARD_RESET -uses HARD_RESET_BUS -uses HARD_RESET_DEVICE -uses HARD_RESET_FUNCTION -uses IRQ_SLOT_COUNT -uses HAVE_OPTION_TABLE -uses CONFIG_MAX_CPUS -uses CONFIG_IOAPIC -uses CONFIG_SMP -uses FALLBACK_SIZE -uses ROM_SIZE -uses ROM_SECTION_SIZE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_SIZE -uses ROM_SECTION_OFFSET -uses CONFIG_ROM_STREAM -uses CONFIG_ROM_STREAM_START -uses PAYLOAD_SIZE -uses _ROMBASE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses STACK_SIZE -uses HEAP_SIZE -uses USE_OPTION_TABLE - -## ROM_SIZE is the size of boot ROM that this board will use. -default ROM_SIZE=524288 - -### -### Build options -### - -## -## Build code for the fallback boot -## -default HAVE_FALLBACK_BOOT=1 - -## -## Build code to reset the motherboard from linuxBIOS -## -default HAVE_HARD_RESET=1 - -default HARD_RESET_BUS=1 -default HARD_RESET_DEVICE=4 -default HARD_RESET_FUNCTION=0 - -## -## Build code to export a programmable irq routing table -## -default HAVE_PIRQ_TABLE=1 -default IRQ_SLOT_COUNT=9 - -## -## Build code to export an x86 MP table -## Useful for specifying IRQ routing values -## -default HAVE_MP_TABLE=1 - -## -## Build code to export a CMOS option table -## -default HAVE_OPTION_TABLE=1 - -## -## Build code for SMP support -## Only worry about 2 micro processors -## -default CONFIG_SMP=1 -default CONFIG_MAX_CPUS=2 - -## -## Build code to setup a generic IOAPIC -## -default CONFIG_IOAPIC=1 - -## -## Clean up the motherboard id strings -## -#default MAINBOARD_PART_NUMBER="HDAMA" -#default MAINBOARD_VENDOR="ARIMA" - -### -### LinuxBIOS layout values -### - -## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. -default ROM_IMAGE_SIZE = 65536 - -## -## Use a small 8K stack -## -default STACK_SIZE=0x2000 - -## -## Use a small 16K heap -## -default HEAP_SIZE=0x4000 - -## -## Only use the option table in a normal image -## -default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE - ## ## Compute the location and size of where this firmware image ## (linuxBIOS plus bootloader) will live in the boot rom chip. @@ -123,7 +16,6 @@ end ## default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) -default CONFIG_ROM_STREAM = 1 ## ## Compute where this copy of linuxBIOS will start in the boot rom @@ -145,15 +37,12 @@ default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) ## arch i386 end -#cpu k8 end ## ## Build the objects we have code for in this directory. ## -#object mainboard.o driver mainboard.o -#object static_devices.o if HAVE_MP_TABLE object mptable.o end if HAVE_PIRQ_TABLE object irq_tables.o end @@ -164,41 +53,41 @@ dir /drivers/ati/ragexl ## Romcc output ## makerule ./failover.E - depends "$(MAINBOARD)/failover.c" - action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E" + depends "$(MAINBOARD)/failover.c ./romcc" + action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" end makerule ./failover.inc - depends "./failover.E ./romcc" - action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E" + depends "$(MAINBOARD)/failover.c ./romcc" + action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" end makerule ./auto.E - depends "$(MAINBOARD)/auto.c option_table.h" - action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E" + depends "$(MAINBOARD)/auto.c option_table.h ./romcc" + action "./romcc -E -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" end makerule ./auto.inc - depends "./auto.E ./romcc" - action "./romcc -mcpu=k8 -O2 ./auto.E > auto.inc" + depends "$(MAINBOARD)/auto.c option_table.h ./romcc" + action "./romcc -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" end ## ## Build our 16 bit and 32 bit linuxBIOS entry code ## -mainboardinit cpu/i386/entry16.inc -mainboardinit cpu/i386/entry32.inc -ldscript /cpu/i386/entry16.lds -ldscript /cpu/i386/entry32.lds +mainboardinit cpu/x86/16bit/entry16.inc +mainboardinit cpu/x86/32bit/entry32.inc +ldscript /cpu/x86/16bit/entry16.lds +ldscript /cpu/x86/32bit/entry32.lds ## ## Build our reset vector (This is where linuxBIOS is entered) ## if USE_FALLBACK_IMAGE - mainboardinit cpu/i386/reset16.inc - ldscript /cpu/i386/reset16.lds + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds else - mainboardinit cpu/i386/reset32.inc - ldscript /cpu/i386/reset32.lds + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds end ### Should this be in the northbridge code? @@ -210,11 +99,6 @@ mainboardinit arch/i386/lib/cpu_reset.inc mainboardinit arch/i386/lib/id.inc ldscript /arch/i386/lib/id.lds -## -## Setup our mtrrs -## -mainboardinit cpu/k8/earlymtrr.inc - ### ### This is the early phase of linuxBIOS startup ### Things are delicate and we test to see if we should @@ -232,9 +116,12 @@ end ## ## Setup RAM ## -mainboardinit cpu/k8/enable_mmx_sse.inc +mainboardinit cpu/x86/fpu/enable_fpu.inc +mainboardinit cpu/x86/mmx/enable_mmx.inc +mainboardinit cpu/x86/sse/enable_sse.inc mainboardinit ./auto.inc -mainboardinit cpu/k8/disable_mmx_sse.inc +mainboardinit cpu/x86/sse/disable_sse.inc +mainboardinit cpu/x86/mmx/disable_mmx.inc ## ## Include the secondary Configuration files @@ -242,6 +129,7 @@ mainboardinit cpu/k8/disable_mmx_sse.inc dir /pc80 config chip.h +# config for arima/hdama chip northbridge/amd/amdk8 device pci_domain 0 on device pci 18.0 on # LDT 0 @@ -330,9 +218,3 @@ chip northbridge/amd/amdk8 end end -## -## Include the old serial code for those few places that still need it. -## -mainboardinit pc80/serial.inc -mainboardinit arch/i386/lib/console.inc - |