diff options
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/BiosCallOuts.c | 108 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/Kconfig | 1 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/Makefile.inc | 20 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/Memphis_MEM4G16D3EABG.spd.hex | 237 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/OemCustomize.c | 116 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/board_info.txt | 4 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/devicetree.cb | 21 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/mainboard.c | 102 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/mptable.c | 174 | ||||
| -rw-r--r-- | src/mainboard/amd/db-ft3b-lc/romstage.c | 10 |
10 files changed, 591 insertions, 202 deletions
diff --git a/src/mainboard/amd/db-ft3b-lc/BiosCallOuts.c b/src/mainboard/amd/db-ft3b-lc/BiosCallOuts.c index 9528f72585..c2f9c83afb 100644 --- a/src/mainboard/amd/db-ft3b-lc/BiosCallOuts.c +++ b/src/mainboard/amd/db-ft3b-lc/BiosCallOuts.c @@ -2,6 +2,7 @@ * This file is part of the coreboot project. * * Copyright (C) 2012 Advanced Micro Devices, Inc. + * 2013 - 2014 Sage Electronic Engineering, LLC * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -16,6 +17,7 @@ #include "AGESA.h" #include "amdlib.h" #include <northbridge/amd/pi/BiosCallOuts.h> +#include <device/azalia.h> #include "Ids.h" #include "heapManager.h" #include "FchPlatform.h" @@ -33,7 +35,7 @@ const BIOS_CALLOUT_STRUCT BiosCallouts[] = {AGESA_ALLOCATE_BUFFER, agesa_AllocateBuffer }, {AGESA_DEALLOCATE_BUFFER, agesa_DeallocateBuffer }, {AGESA_LOCATE_BUFFER, agesa_LocateBuffer }, - {AGESA_READ_SPD, agesa_ReadSpd }, + {AGESA_READ_SPD, agesa_ReadSpd_from_cbfs }, {AGESA_DO_RESET, agesa_Reset }, {AGESA_READ_SPD_RECOVERY, agesa_NoopUnsupported }, {AGESA_RUNFUNC_ONAP, agesa_RunFuncOnAp }, @@ -49,26 +51,41 @@ const int BiosCalloutsLen = ARRAY_SIZE(BiosCallouts); * Realtek ALC272 CODEC Verb Table */ static const CODEC_ENTRY Alc272_VerbTbl[] = { - {0x11, 0x411111F0}, // - SPDIF_OUT2 - {0x12, 0x411111F0}, // - DMIC_1/2 - {0x13, 0x411111F0}, // - DMIC_3/4 - {0x14, 0x411111F0}, // Port D - LOUT1 - {0x15, 0x411111F0}, // Port A - LOUT2 - {0x16, 0x411111F0}, // - {0x17, 0x411111F0}, // Port H - MONO - {0x18, 0x01a19840}, // Port B - MIC1 - {0x19, 0x411111F0}, // Port F - MIC2 - {0x1a, 0x01813030}, // Port C - LINE1 - {0x1b, 0x411111F0}, // Port E - LINE2 - {0x1d, 0x40251E05}, // - PCBEEP - {0x1e, 0x01441120}, // - SPDIF_OUT1 - {0x21, 0x01214010}, // Port I - HPOUT - {0xff, 0xffffffff} + { 0x11, 0x411111F0 }, /* - S/PDIF Output 2 */ + { 0x12, 0x411111F0 }, /* - Digital Mic 1/2 [GPIO0] */ + { 0x13, 0x411111F0 }, /* - Digital Mic 3/4 [GPIO1] */ + { 0x14, 0x411111F0 }, /* Port D - Front Panel headphone */ + { 0x15, 0x411111F0 }, /* Port A - Surround */ + { 0x17, 0x411111F0 }, /* Port H - Mono */ + { 0x18, /* Port B - MIC - combo jack */ + (AZALIA_PINCFG_PORT_JACK << 30) + | ((AZALIA_PINCFG_LOCATION_EXTERNAL | AZALIA_PINCFG_LOCATION_REAR) << 24) + | (AZALIA_PINCFG_DEVICE_MICROPHONE << 20) + | (AZALIA_PINCFG_CONN_MINI_HEADPHONE_JACK << 16) + | (AZALIA_PINCFG_COLOR_BLACK << 12) + | (4 << 4) + | (0 << 0) + }, + { 0x19, 0x411111F0 }, /* Port F - Front Panel Mic */ + { 0x1A, 0x411111F0 }, /* Port C - LINE1 */ + { 0x1B, 0x411111F0 }, /* Port E - Front Panel line-out */ + { 0x1D, 0x40130605 }, /* - PCBEEP */ + { 0x1E, 0x411111F0 }, /* - SPDIF_OUT1 */ + { 0x21, /* Port I - HPout - combo jack */ + (AZALIA_PINCFG_PORT_JACK << 30) + | ((AZALIA_PINCFG_LOCATION_EXTERNAL | AZALIA_PINCFG_LOCATION_REAR) << 24) + | (AZALIA_PINCFG_DEVICE_HP_OUT << 20) + | (AZALIA_PINCFG_CONN_MINI_HEADPHONE_JACK << 16) + | (AZALIA_PINCFG_COLOR_BLACK << 12) + | (4 << 4) + | (0 << 0) + }, + { 0xFF, 0xFFFFFFFF }, }; static const CODEC_TBL_LIST CodecTableList[] = { - {0x10ec0272, (CODEC_ENTRY*)&Alc272_VerbTbl[0]}, + {0x10ec0272, Alc272_VerbTbl}, {(UINT32)0x0FFFFFFFF, (CODEC_ENTRY*)0x0FFFFFFFFUL} }; @@ -141,40 +158,40 @@ static void oem_fan_control(FCH_DATA_BLOCK *FchParams) /* Thermal Zone Parameter */ FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg0 = 0x00; FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg1 = 0x00; /* Zone */ - FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg2 = 0x3d; //BIT0 | BIT2 | BIT5; - FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg3 = 0x4e; //6 | BIT3; + FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg2 = 0x00; //BIT0 | BIT2 | BIT5; + FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg3 = 0x00; //6 | BIT3; FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg4 = 0x00; - FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg5 = 0x04; - FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg6 = 0x9a; /* SMBUS Address for SMBUS based temperature sensor such as SB-TSI and ADM1032 */ - FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg7 = 0x01; - FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg8 = 0x01; /* PWM steping rate in unit of PWM level percentage */ - FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg9 = 0x00; + FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg5 = 0x00; + FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg6 = 0x98; /* SMBUS Address for SMBUS based temperature sensor such as SB-TSI and ADM1032 */ + FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg7 = 2; + FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg8 = 0; /* PWM steping rate in unit of PWM level percentage */ + FchParams->Imc.EcStruct.MsgFun81Zone0MsgReg9 = 0; /* IMC Fan Policy temperature thresholds */ FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg0 = 0x00; FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg1 = 0x00; /* Zone */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg2 = 0x46; /*AC0 threshold in Celsius */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg3 = 0x3c; /*AC1 threshold in Celsius */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg4 = 0x32; /*AC2 threshold in Celsius */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg5 = 0xff; /*AC3 threshold in Celsius, 0xFF is not define */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg6 = 0xff; /*AC4 threshold in Celsius, 0xFF is not define */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg7 = 0xff; /*AC5 threshold in Celsius, 0xFF is not define */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg8 = 0xff; /*AC6 threshold in Celsius, 0xFF is not define */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg9 = 0xff; /*AC7 lowest threshold in Celsius, 0xFF is not define */ - FchParams->Imc.EcStruct.MsgFun83Zone0MsgRegA = 0x4b; /*critical threshold* in Celsius, 0xFF is not define */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg2 = 0; /*AC0 threshold in Celsius */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg3 = 0; /*AC1 threshold in Celsius */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg4 = 0; /*AC2 threshold in Celsius */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg5 = 0; /*AC3 threshold in Celsius, 0xFF is not define */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg6 = 0; /*AC4 threshold in Celsius, 0xFF is not define */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg7 = 0; /*AC5 threshold in Celsius, 0xFF is not define */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg8 = 0; /*AC6 threshold in Celsius, 0xFF is not define */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgReg9 = 0; /*AC7 lowest threshold in Celsius, 0xFF is not define */ + FchParams->Imc.EcStruct.MsgFun83Zone0MsgRegA = 0; /*critical threshold* in Celsius, 0xFF is not define */ FchParams->Imc.EcStruct.MsgFun83Zone0MsgRegB = 0x00; /* IMC Fan Policy PWM Settings */ FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg0 = 0x00; FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg1 = 0x00; /* Zone */ - FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg2 = 0x5a; /* AL0 percentage */ - FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg3 = 0x46; /* AL1 percentage */ - FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg4 = 0x28; /* AL2 percentage */ - FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg5 = 0xff; /* AL3 percentage */ - FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg6 = 0xff; /* AL4 percentage */ - FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg7 = 0xff; /* AL5 percentage */ - FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg8 = 0xff; /* AL6 percentage */ - FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg9 = 0xff; /* AL7 percentage */ + FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg2 = 0; /* AL0 percentage */ + FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg3 = 0; /* AL1 percentage */ + FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg4 = 0; /* AL2 percentage */ + FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg5 = 0x00; /* AL3 percentage */ + FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg6 = 0x00; /* AL4 percentage */ + FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg7 = 0x00; /* AL5 percentage */ + FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg8 = 0x00; /* AL6 percentage */ + FchParams->Imc.EcStruct.MsgFun85Zone0MsgReg9 = 0x00; /* AL7 percentage */ FchParams->Imc.EcStruct.MsgFun81Zone1MsgReg0 = 0x00; FchParams->Imc.EcStruct.MsgFun81Zone1MsgReg1 = 0x01; /* Zone */ @@ -273,7 +290,14 @@ static AGESA_STATUS Fch_Oem_config(UINT32 Func, UINT32 FchData, VOID *ConfigPtr) printk(BIOS_DEBUG, "Fch OEM config in INIT ENV "); /* Azalia Controller OEM Codec Table Pointer */ - FchParams->Azalia.AzaliaOemCodecTablePtr = (CODEC_TBL_LIST *)(&CodecTableList[0]); + FchParams->Azalia.AzaliaPinCfg = TRUE; + FchParams->Azalia.AzaliaConfig = (const AZALIA_PIN){ + .AzaliaSdin0 = (CONFIG_AZ_PIN>>0) & 0x03, + .AzaliaSdin1 = (CONFIG_AZ_PIN>>2) & 0x03, + .AzaliaSdin2 = (CONFIG_AZ_PIN>>4) & 0x03, + .AzaliaSdin3 = (CONFIG_AZ_PIN>>6) & 0x03 + }; + FchParams->Azalia.AzaliaOemCodecTablePtr = CodecTableList; /* Azalia Controller Front Panel OEM Table Pointer */ /* Fan Control */ diff --git a/src/mainboard/amd/db-ft3b-lc/Kconfig b/src/mainboard/amd/db-ft3b-lc/Kconfig index 437968dded..ace741ddcc 100644 --- a/src/mainboard/amd/db-ft3b-lc/Kconfig +++ b/src/mainboard/amd/db-ft3b-lc/Kconfig @@ -27,6 +27,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select HAVE_ACPI_TABLES select BOARD_ROMSIZE_KB_8192 select GFXUMA + select SPD_CACHE config MAINBOARD_DIR string diff --git a/src/mainboard/amd/db-ft3b-lc/Makefile.inc b/src/mainboard/amd/db-ft3b-lc/Makefile.inc index 37c1dceead..8b160e26f4 100644 --- a/src/mainboard/amd/db-ft3b-lc/Makefile.inc +++ b/src/mainboard/amd/db-ft3b-lc/Makefile.inc @@ -18,3 +18,23 @@ romstage-y += OemCustomize.c ramstage-y += BiosCallOuts.c ramstage-y += OemCustomize.c + +## DIMM SPD for on-board memory +SPD_BIN = $(obj)/spd.bin + +# Order of names in SPD_SOURCES is important! +SPD_SOURCES = Memphis_MEM4G16D3EABG + +SPD_DEPS := $(foreach f, $(SPD_SOURCES), src/mainboard/$(MAINBOARDDIR)/$(f).spd.hex) + +# Include spd rom data +$(SPD_BIN): $(SPD_DEPS) + for f in $+; \ + do for c in $$(cat $$f | grep -v ^#); \ + do printf $$(printf '\%o' 0x$$c); \ + done; \ + done > $@ + +cbfs-files-y += spd.bin +spd.bin-file := $(SPD_BIN) +spd.bin-type := spd diff --git a/src/mainboard/amd/db-ft3b-lc/Memphis_MEM4G16D3EABG.spd.hex b/src/mainboard/amd/db-ft3b-lc/Memphis_MEM4G16D3EABG.spd.hex new file mode 100644 index 0000000000..3bbe027a88 --- /dev/null +++ b/src/mainboard/amd/db-ft3b-lc/Memphis_MEM4G16D3EABG.spd.hex @@ -0,0 +1,237 @@ +# +# This file is part of the coreboot project. +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; version 2 of the License. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# + +# LOWCOST board has 2GB using 4 Memphis MEM4G16D3EABG chips + +# The datasheet is available at: +# http://www.memphis.ag/fileadmin/datasheets/MEM4G16D3EABG_10.pdf + +# SPD contents for LC (LowCost) 4GB DDR3 (1600MHz) soldered down + +# 0 Number of SPD Bytes used / Total SPD Size / CRC Coverage +# bits[3:0]: 1 = 128 SPD Bytes Used +# bits[6:4]: 1 = 256 SPD Bytes Total +# bit7 : 0 = CRC covers bytes 0 ~ 125 +11 + +# 1 SPD Revision - +# 0x10 = Revision 1.0 +10 + +# 2 Key Byte / DRAM Device Type +# bits[7:0]: 0x0b = DDR3 SDRAM +0B + +# 3 Key Byte / Module Type +# bits[3:0]: 1 = RDIMM +# bits[3:0]: 2 = UDIMM +# bits[3:0]: 3 = SO-DIMM +# bits[7:4]: reserved +03 + +# 4 SDRAM CHIP Density and Banks +# bits[3:0]: 3 = 2 Gigabits Total SDRAM capacity per chip +# bits[3:0]: 4 = 4 Gigabits Total SDRAM capacity per chip +# bits[6:4]: 0 = 3 (8 banks) +# bit7 : reserved +04 + +# 5 SDRAM Addressing +# bits[2:0]: 1 = 10 Column Address Bits +# bits[5:3]: 2 = 14 Row Address Bits +# bits[5:3]: 3 = 15 Row Address Bits +# bits[7:6]: reserved +19 + +# 6 Module Nominal Voltage, VDD +# bit0 : 0 = 1.5 V operable +# bit1 : 0 = NOT 1.35 V operable +# bit2 : 0 = NOT 1.25 V operable +# bits[7:3]: reserved +00 + +# 7 Module Organization +# bits[2:0]: 2 = 16 bits +# bits[5:3]: 0 = 1 Rank +# bits[7:6]: reserved +02 + +# 8 Module Memory Bus Width +# bits[2:0]: 3 = Primary bus width is 64 bits +# bits[4:3]: 0 = 0 bits (no bus width extension) +# bits[7:5]: reserved +03 + +# 9 Fine Timebase (FTB) Dividend / Divisor +# bits[3:0]: 0x02 divisor +# bits[7:4]: 0x05 dividend +# 5/2 = 2.5ps +52 + +# 10 Medium Timebase (MTB) Dividend +# 11 Medium Timebase (MTB) Divisor +# 1 / 8 = .125 ns - used for clock freq of 400 through 1066 MHz +01 08 + +# 12 SDRAM Minimum Cycle Time (tCKmin) +# 0x0a = tCKmin of 1.25 ns = DDR3-1600 (800 MHz clock) +0A + +# 13 Reserved +00 + +# 14 CAS Latencies Supported, Least Significant Byte +# 15 CAS Latencies Supported, Most Significant Byte +# Cas Latencies of 11 - 5 are supported +FE 00 + +# 16 Minimum CAS Latency Time (tAAmin) +# 0x6E = 13.75ns - DDR3-1600K +6E + +# 17 Minimum Write Recovery Time (tWRmin) +# 0x78 = tWR of 15ns - All DDR3 speed grades +78 + +# 18 Minimum RAS# to CAS# Delay Time (tRCDmin) +# 0x6E = 13.75ns - DDR3-1600K +6E + +# 19 Minimum Row Active to Row Active Delay Time (tRRDmin) +# 0x3C = 7.5ns +3C + +# 20 Minimum Row Precharge Delay Time (tRPmin) +# 0x6E = 13.75ns - DDR3-1600K +6E + +# 21 Upper Nibbles for tRAS and tRC +# bits[3:0]: tRAS most significant nibble = 1 (see byte 22) +# bits[7:4]: tRC most significant nibble = 1 (see byte 23) +11 + +# 22 Minimum Active to Precharge Delay Time (tRASmin), LSB +# 0x118 = 35ns - DDR3-1600 (see byte 21) +2C + +# 23 Minimum Active to Active/Refresh Delay Time (tRCmin), LSB +# 0x186 = 48.75ns - DDR3-1600K +95 + +# 24 Minimum Refresh Recovery Delay Time (tRFCmin), LSB +# 25 Minimum Refresh Recovery Delay Time (tRFCmin), MSB +# 0x500 = 160ns - for 2 Gigabit chips +# 0x820 = 260ns - for 4 Gigabit chips +20 08 + +# 26 Minimum Internal Write to Read Command Delay Time (tWTRmin) +# 0x3c = 7.5 ns - All DDR3 SDRAM speed bins +3C + +# 27 Minimum Internal Read to Precharge Command Delay Time (tRTPmin) +# 0x3c = 7.5ns - All DDR3 SDRAM speed bins +3C + +# 28 Upper Nibble for tFAWmin +# 29 Minimum Four Activate Window Delay Time (tFAWmin) +# 0x0140 = 40ns - DDR3-1600, 2 KB page size +# 0x00F0 = 30ns - DDR3-1600, 2 KB page size +00 F0 + +# 30 SDRAM Optional Feature +# bit0 : 1= RZQ/6 supported +# bit1 : 1 = RZQ/7 supported +# bits[6:2]: reserved +# bit7 : 1 = DLL Off mode supported +83 + +# 31 SDRAM Thermal and Refresh Options +# bit0 : 1 = Temp up to 95c supported +# bit1 : 0 = 85-95c uses 2x refresh rate +# bit2 : 1 = Auto Self Refresh supported +# bit3 : 0 = no on die thermal sensor +# bits[6:4]: reserved +# bit7 : 0 = partial self refresh supported +05 + +# 32 Module Thermal Sensor +# 0 = Thermal sensor not incorporated onto this assembly +00 + +# 33 SDRAM Device Type +# bits[1:0]: 0 = Signal Loading not specified +# bits[3:2]: reserved +# bits[6:4]: 0 = Die count not specified +# bit7 : 0 = Standard Monolithic DRAM Device +00 + +# 34 Fine Offset for SDRAM Minimum Cycle Time (tCKmin) +# 35 Fine Offset for Minimum CAS Latency Time (tAAmin) +# 36 Fine Offset for Minimum RAS# to CAS# Delay Time (tRCDmin) +# 37 Fine Offset for Minimum Row Precharge Delay Time (tRPmin) +# 38 Fine Offset for Minimum Active to Active/Refresh Delay (tRCmin) +00 00 00 00 00 + +# 39 - 59 (reserved) +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 + +# 60 Raw Card Extension, Module Nominal Height +# bits[4:0]: 0 = <= 15mm tall +# bits[7:5]: 0 = raw card revision 0-3 +00 + +# 61 Module Maximum Thickness +# bits[3:0]: 0 = thickness front <= 1mm +# bits[7:4]: 0 = thinkness back <= 1mm +00 + +# 62 Reference Raw Card Used +# bits[4:0]: 0 = Reference Raw card A used +# bits[6:5]: 0 = revision 0 +# bit7 : 0 = Reference raw cards A through AL +00 + +# 63 Address Mapping from Edge Connector to DRAM +# bit0 : 0 = standard mapping (not mirrored) +# bits[7:1]: reserved +00 + +# 64 - 116 (reserved) +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 + +# 117 - 118 Module ID: Module Manufacturers JEDEC ID Code +# 0x0001 = AMD +00 01 + +# 119 Module ID: Module Manufacturing Location - oem specified +# 120 Module ID: Module Manufacture Year in BCD +# 0x14 = 2014 +00 14 + +# 121 Module ID: Module Manufacture week +# 0x12 = 12th week +12 + +# 122 - 125: Module Serial Number +00 00 00 00 + +# 126 - 127: Cyclical Redundancy Code +00 00 diff --git a/src/mainboard/amd/db-ft3b-lc/OemCustomize.c b/src/mainboard/amd/db-ft3b-lc/OemCustomize.c index ac60c42082..e8146a03d4 100644 --- a/src/mainboard/amd/db-ft3b-lc/OemCustomize.c +++ b/src/mainboard/amd/db-ft3b-lc/OemCustomize.c @@ -13,7 +13,9 @@ * GNU General Public License for more details. */ +#include <AGESA.h> #include <northbridge/amd/pi/agesawrapper.h> +#include <PlatformMemoryConfiguration.h> #define FILECODE PROC_GNB_PCIE_FAMILY_0X15_F15PCIECOMPLEXCONFIG_FILECODE @@ -73,21 +75,9 @@ static const PCIe_PORT_DESCRIPTOR PortList [] = { static const PCIe_DDI_DESCRIPTOR DdiList [] = { /* DP0 to HDMI0/DP */ { - 0, - PCIE_ENGINE_DATA_INITIALIZER (PcieDdiEngine, 8, 11), - PCIE_DDI_DATA_INITIALIZER (ConnectorTypeDP, Aux1, Hdp1) - }, - /* DP1 to FCH */ - { - 0, - PCIE_ENGINE_DATA_INITIALIZER (PcieDdiEngine, 12, 15), - PCIE_DDI_DATA_INITIALIZER (ConnectorTypeDP, Aux2, Hdp2) - }, - /* DP2 to HDMI1/DP */ - { DESCRIPTOR_TERMINATE_LIST, - PCIE_ENGINE_DATA_INITIALIZER (PcieDdiEngine, 16, 19), - PCIE_DDI_DATA_INITIALIZER (ConnectorTypeCrt, Aux3, Hdp3) + PCIE_ENGINE_DATA_INITIALIZER (PcieDdiEngine, 8, 11), + PCIE_DDI_DATA_INITIALIZER (ConnectorTypeHDMI, Aux1, Hdp1) }, }; @@ -120,3 +110,101 @@ OemCustomizeInitEarly ( { InitEarly->GnbConfig.PcieComplexList = &PcieComplex; } + +/* + * Platform Specific Overriding Table allows IBV/OEM to pass in platform information to AGESA + * (e.g. MemClk routing, the number of DIMM slots per channel,...). If PlatformSpecificTable + * is populated, AGESA will base its settings on the data from the table. Otherwise, it will + * use its default conservative settings. + */ +static const PSO_ENTRY ROMDATA PlatformMemoryConfiguration[] = { + // + // The following macros are supported (use comma to separate macros): + // + // MEMCLK_DIS_MAP(SocketID, ChannelID, MemClkDisBit0CSMap,..., MemClkDisBit7CSMap) + // The MemClk pins are identified based on BKDG definition of Fn2x88[MemClkDis] bitmap. + // AGESA will base on this value to disable unused MemClk to save power. + // Example: + // BKDG definition of Fn2x88[MemClkDis] bitmap for AM3 package is like below: + // Bit AM3/S1g3 pin name + // 0 M[B,A]_CLK_H/L[0] + // 1 M[B,A]_CLK_H/L[1] + // 2 M[B,A]_CLK_H/L[2] + // 3 M[B,A]_CLK_H/L[3] + // 4 M[B,A]_CLK_H/L[4] + // 5 M[B,A]_CLK_H/L[5] + // 6 M[B,A]_CLK_H/L[6] + // 7 M[B,A]_CLK_H/L[7] + // And platform has the following routing: + // CS0 M[B,A]_CLK_H/L[4] + // CS1 M[B,A]_CLK_H/L[2] + // CS2 M[B,A]_CLK_H/L[3] + // CS3 M[B,A]_CLK_H/L[5] + // Then platform can specify the following macro: + // MEMCLK_DIS_MAP(ANY_SOCKET, ANY_CHANNEL, 0x00, 0x00, 0x02, 0x04, 0x01, 0x08, 0x00, 0x00) + // + // CKE_TRI_MAP(SocketID, ChannelID, CKETriBit0CSMap, CKETriBit1CSMap) + // The CKE pins are identified based on BKDG definition of Fn2x9C_0C[CKETri] bitmap. + // AGESA will base on this value to tristate unused CKE to save power. + // + // ODT_TRI_MAP(SocketID, ChannelID, ODTTriBit0CSMap,..., ODTTriBit3CSMap) + // The ODT pins are identified based on BKDG definition of Fn2x9C_0C[ODTTri] bitmap. + // AGESA will base on this value to tristate unused ODT pins to save power. + // + // CS_TRI_MAP(SocketID, ChannelID, CSTriBit0CSMap,..., CSTriBit7CSMap) + // The Chip select pins are identified based on BKDG definition of Fn2x9C_0C[ChipSelTri] bitmap. + // AGESA will base on this value to tristate unused Chip select to save power. + // + // NUMBER_OF_DIMMS_SUPPORTED(SocketID, ChannelID, NumberOfDimmSlotsPerChannel) + // Specifies the number of DIMM slots per channel. + // + // NUMBER_OF_CHIP_SELECTS_SUPPORTED(SocketID, ChannelID, NumberOfChipSelectsPerChannel) + // Specifies the number of Chip selects per channel. + // + // NUMBER_OF_CHANNELS_SUPPORTED(SocketID, NumberOfChannelsPerSocket) + // Specifies the number of channels per socket. + // + // OVERRIDE_DDR_BUS_SPEED(SocketID, ChannelID, USER_MEMORY_TIMING_MODE, MEMORY_BUS_SPEED) + // Specifies DDR bus speed of channel ChannelID on socket SocketID. + // + // DRAM_TECHNOLOGY(SocketID, TECHNOLOGY_TYPE) + // Specifies the DRAM technology type of socket SocketID (DDR2, DDR3,...) + // + // WRITE_LEVELING_SEED(SocketID, ChannelID, DimmID, Byte0Seed, Byte1Seed, Byte2Seed, Byte3Seed, Byte4Seed, Byte5Seed, + // Byte6Seed, Byte7Seed, ByteEccSeed) + // Specifies the write leveling seed for a channel of a socket. + // + // HW_RXEN_SEED(SocketID, ChannelID, DimmID, Byte0Seed, Byte1Seed, Byte2Seed, Byte3Seed, Byte4Seed, Byte5Seed, + // Byte6Seed, Byte7Seed, ByteEccSeed) + // Speicifes the HW RXEN training seed for a channel of a socket + // + +#define SEED_WL 0x0E +WRITE_LEVELING_SEED( + ANY_SOCKET, CHANNEL_A, ALL_DIMMS, + SEED_WL,SEED_WL,SEED_WL,SEED_WL,SEED_WL,SEED_WL,SEED_WL,SEED_WL, + SEED_WL), + +#define SEED_A 0x12 +HW_RXEN_SEED( + ANY_SOCKET, CHANNEL_A, ALL_DIMMS, + SEED_A, SEED_A, SEED_A, SEED_A, SEED_A, SEED_A, SEED_A, SEED_A, + SEED_A), + + NUMBER_OF_DIMMS_SUPPORTED (ANY_SOCKET, ANY_CHANNEL, 1), + NUMBER_OF_CHANNELS_SUPPORTED (ANY_SOCKET, 1), + MOTHER_BOARD_LAYERS (LAYERS_6), + + MEMCLK_DIS_MAP (ANY_SOCKET, ANY_CHANNEL, 0x01, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00), + CKE_TRI_MAP (ANY_SOCKET, ANY_CHANNEL, 0x01, 0x02, 0x04, 0x08), /* TODO: bit2map, bit3map */ + ODT_TRI_MAP (ANY_SOCKET, ANY_CHANNEL, 0x01, 0x02, 0x04, 0x08), + CS_TRI_MAP (ANY_SOCKET, ANY_CHANNEL, 0x01, 0x02, 0x04, 0x08, 0x00, 0x00, 0x00, 0x00), + + PSO_END +}; + +void OemPostParams(AMD_POST_PARAMS *PostParams) +{ + /* Add the memory configuration table needed for soldered down memory */ + PostParams->MemConfig.PlatformMemoryConfiguration = (PSO_ENTRY *)PlatformMemoryConfiguration; +} diff --git a/src/mainboard/amd/db-ft3b-lc/board_info.txt b/src/mainboard/amd/db-ft3b-lc/board_info.txt index d2c6670225..5854f86515 100644 --- a/src/mainboard/amd/db-ft3b-lc/board_info.txt +++ b/src/mainboard/amd/db-ft3b-lc/board_info.txt @@ -1,5 +1,5 @@ -Board name: DB-FT3b (Olive Hill+) -Board URL: http://wwwd.amd.com/amd/devsite.nsf/platforms/DB-FT3.htm +Board name: DB-FT3b-LC +Board URL: http://wwwd.amd.com/amd/devsite.nsf/platforms/db-ft3-lc.htm Category: eval ROM protocol: SPI ROM socketed: n diff --git a/src/mainboard/amd/db-ft3b-lc/devicetree.cb b/src/mainboard/amd/db-ft3b-lc/devicetree.cb index ee0cd98bfe..1faebf4c70 100644 --- a/src/mainboard/amd/db-ft3b-lc/devicetree.cb +++ b/src/mainboard/amd/db-ft3b-lc/devicetree.cb @@ -2,6 +2,7 @@ # This file is part of the coreboot project. # # Copyright (C) 2013 Advanced Micro Devices, Inc. +# Copyright (C) 2015 Kyösti Mälkki <kyosti.malkki@gmail.com> # # This program is free software; you can redistribute it and/or modify # it under the terms of the GNU General Public License as published by @@ -32,9 +33,9 @@ chip northbridge/amd/pi/00730F01/root_complex device pci 2.1 on end # x4 PCIe slot device pci 2.2 on end # mPCIe slot device pci 2.3 on end # Realtek NIC - device pci 2.4 on end # Edge Connector - device pci 2.5 on end # Edge Connector - device pci 8.0 on end # Platform Security Processor + device pci 2.4 off end # Edge Connector + device pci 2.5 off end # Edge Connector + device pci 8.0 off end # Platform Security Processor end #chip northbridge/amd/pi/00730F01 chip southbridge/amd/pi/hudson # it is under NB/SB Link, but on the same pci bus @@ -42,18 +43,12 @@ chip northbridge/amd/pi/00730F01/root_complex device pci 11.0 on end # SATA device pci 12.0 on end # EHCI #0 device pci 13.0 on end # EHCI #1 - device pci 14.0 on # SMBus - chip drivers/generic/generic #dimm 0-0-0 - device i2c 50 on end - end - chip drivers/generic/generic #dimm 0-0-1 - device i2c 51 on end - end - end # SMbus + device pci 14.0 on end # SMBus device pci 14.2 on end # HDA 0x4383 device pci 14.3 on end # LPC 0x439d device pci 14.7 on end # SD device pci 16.0 on end # EHCI #2 + register "sd_mode" = "3" end #chip southbridge/amd/pi/hudson device pci 18.0 on end @@ -62,10 +57,6 @@ chip northbridge/amd/pi/00730F01/root_complex device pci 18.3 on end device pci 18.4 on end device pci 18.5 on end - register "spdAddrLookup" = " - { - { {0xA0, 0xA2} }, // socket 0, channel 0, slots 0 & 1 - 8-bit SPD addresses - }" end #chip northbridge/amd/pi/00730F01 # CPU side of HT root complex end #domain diff --git a/src/mainboard/amd/db-ft3b-lc/mainboard.c b/src/mainboard/amd/db-ft3b-lc/mainboard.c index 1e82768ddd..6f8742c20a 100644 --- a/src/mainboard/amd/db-ft3b-lc/mainboard.c +++ b/src/mainboard/amd/db-ft3b-lc/mainboard.c @@ -2,6 +2,7 @@ * This file is part of the coreboot project. * * Copyright (C) 2012 Advanced Micro Devices, Inc. + * Copyright (C) 2014 Sage Electronic Engineering, LLC. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -13,18 +14,110 @@ * GNU General Public License for more details. */ +#include <arch/acpi.h> +#include <arch/io.h> #include <console/console.h> +#include <cpu/amd/pi/s3_resume.h> #include <device/device.h> #include <device/pci.h> -#include <arch/io.h> #include <device/pci_def.h> -#include <arch/acpi.h> #include <northbridge/amd/pi/BiosCallOuts.h> -#include <cpu/amd/pi/s3_resume.h> #include <northbridge/amd/pi/agesawrapper.h> +#include <southbridge/amd/pi/hudson/hudson.h> +#include <southbridge/amd/pi/hudson/pci_devs.h> +#include <southbridge/amd/pi/hudson/amd_pci_int_defs.h> +#include <northbridge/amd/pi/00730F01/pci_devs.h> +#include <southbridge/amd/common/amd_pci_util.h> + #include <cpu/x86/msr.h> #include <cpu/amd/mtrr.h> +/*********************************************************** + * These arrays set up the FCH PCI_INTR registers 0xC00/0xC01. + * This table is responsible for physically routing the PIC and + * IOAPIC IRQs to the different PCI devices on the system. It + * is read and written via registers 0xC00/0xC01 as an + * Index/Data pair. These values are chipset and mainboard + * dependent and should be updated accordingly. + * + * These values are used by the PCI configuration space, + * MP Tables. TODO: Make ACPI use these values too. + */ +static const u8 mainboard_picr_data[FCH_INT_TABLE_SIZE] = { +#if defined(__GNUC__) + [0 ... FCH_INT_TABLE_SIZE-1] = 0x1F, +#endif + /* INTA# - INTH# */ + [0x00] = 0x0A,0x0B,0x0A,0x0B,0x0A,0x0B,0x0A,0x0B, + /* Misc-nil,0,1,2, INT from Serial irq */ + [0x08] = 0xFA,0xF1,0x00,0x00,0x1F,0x1F,0x1F,0x1F, + /* SCI, SMBUS0, ASF, HDA, FC, RSVD, PerMon, SD */ + [0x10] = 0x1F,0x1F,0x1F,0x1F,0x1F,0x1F,0x1F,0x1F, + /* IMC INT0 - 5 */ + [0x20] = 0x1F,0x1F,0x1F,0x1F,0x1F,0x1F, + /* USB Devs 18/19/22 INTA-C */ + [0x30] = 0x0A,0x0B,0x0A,0x0B,0x0A,0x0B, + /* SATA */ + [0x41] = 0x0F, +}; + +static const u8 mainboard_intr_data[FCH_INT_TABLE_SIZE] = { +#if defined(__GNUC__) + [0 ... FCH_INT_TABLE_SIZE-1] = 0x1F, +#endif + /* INTA# - INTH# */ + [0x00] = 0x10,0x11,0x12,0x13,0x14,0x15,0x16,0x17, + /* Misc-nil,0,1,2, INT from Serial irq */ + [0x08] = 0x00,0x00,0x00,0x00,0x1F,0x1F,0x1F,0x1F, + /* SCI, SMBUS0, ASF, HDA, FC, RSVD, PerMon, SD */ + [0x10] = 0x09,0x1F,0x1F,0x10,0x1F,0x1F,0x1F,0x10, + /* IMC INT0 - 5 */ + [0x20] = 0x1F,0x1F,0x1F,0x1F,0x1F,0x1F, + /* USB Devs 18/19/20/22 INTA-C */ + [0x30] = 0x12,0x11,0x12,0x11,0x12,0x11,0x12, + /* SATA */ + [0x41] = 0x13, +}; + +/* + * This table defines the index into the picr/intr_data + * tables for each device. Any enabled device and slot + * that uses hardware interrupts should have an entry + * in this table to define its index into the FCH + * PCI_INTR register 0xC00/0xC01. This index will define + * the interrupt that it should use. Putting PIRQ_A into + * the PIN A index for a device will tell that device to + * use PIC IRQ 10 if it uses PIN A for its hardware INT. + */ +static const struct pirq_struct mainboard_pirq_data[] = { + /* {PCI_devfn, {PIN A, PIN B, PIN C, PIN D}}, */ + {GFX_DEVFN, {PIRQ_A, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* VGA: 01.0 */ + {ACTL_DEVFN,{PIRQ_NC, PIRQ_B, PIRQ_NC, PIRQ_NC}}, /* Audio: 01.1 */ + {NB_PCIE_PORT1_DEVFN, {PIRQ_A, PIRQ_B, PIRQ_C, PIRQ_D}}, /* x4 PCIe: 02.1 */ + {NB_PCIE_PORT2_DEVFN, {PIRQ_B, PIRQ_C, PIRQ_D, PIRQ_A}}, /* mPCIe: 02.2 */ + {NB_PCIE_PORT3_DEVFN, {PIRQ_C, PIRQ_D, PIRQ_A, PIRQ_B}}, /* NIC: 02.3 */ + {XHCI_DEVFN, {PIRQ_C, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* XHCI: 10.0 */ + {SATA_DEVFN, {PIRQ_SATA, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* SATA: 11.0 */ + {OHCI1_DEVFN, {PIRQ_OHCI1, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* OHCI1: 12.0 */ + {EHCI1_DEVFN, {PIRQ_NC, PIRQ_EHCI1, PIRQ_NC, PIRQ_NC}}, /* EHCI1: 12.2 */ + {OHCI2_DEVFN, {PIRQ_OHCI2, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* OHCI2: 13.0 */ + {EHCI2_DEVFN, {PIRQ_NC, PIRQ_EHCI2, PIRQ_NC, PIRQ_NC}}, /* EHCI2: 13.2 */ + {SMBUS_DEVFN, {PIRQ_SMBUS, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* SMBUS: 14.0 */ + {HDA_DEVFN, {PIRQ_HDA, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* HDA: 14.2 */ + {SD_DEVFN, {PIRQ_SD, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* SD: 14.7 */ + {OHCI3_DEVFN, {PIRQ_OHCI3, PIRQ_NC, PIRQ_NC, PIRQ_NC}}, /* OHCI3: 16.0 (same device as xHCI 10.0) */ + {EHCI3_DEVFN, {PIRQ_NC, PIRQ_EHCI3, PIRQ_NC, PIRQ_NC}}, /* EHCI3: 16.2 (same device as xHCI 10.1) */ +}; + +/* PIRQ Setup */ +static void pirq_setup(void) +{ + pirq_data_ptr = mainboard_pirq_data; + pirq_data_size = sizeof(mainboard_pirq_data) / sizeof(struct pirq_struct); + intr_data_ptr = mainboard_intr_data; + picr_data_ptr = mainboard_picr_data; +} + /********************************************** * enable the dedicated function in mainboard. **********************************************/ @@ -34,6 +127,9 @@ static void mainboard_enable(device_t dev) if (acpi_is_wakeup_s3()) agesawrapper_fchs3earlyrestore(); + + /* Initialize the PIRQ data structures for consumption */ + pirq_setup(); } struct chip_operations mainboard_ops = { diff --git a/src/mainboard/amd/db-ft3b-lc/mptable.c b/src/mainboard/amd/db-ft3b-lc/mptable.c index a2ba7f4e76..0c668df1ca 100644 --- a/src/mainboard/amd/db-ft3b-lc/mptable.c +++ b/src/mainboard/amd/db-ft3b-lc/mptable.c @@ -2,6 +2,7 @@ * This file is part of the coreboot project. * * Copyright (C) 2012 Advanced Micro Devices, Inc. + * Copyright (C) 2014 Sage Electronic Engineering, LLC. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -23,88 +24,51 @@ #include <cpu/amd/amdfam15.h> #include <arch/cpu.h> #include <cpu/x86/lapic.h> -#include <southbridge/amd/pi/hudson/hudson.h> - -u8 picr_data[0x54] = { - 0x03,0x04,0x05,0x07,0x0B,0x0A,0x1F,0x1F,0xFA,0xF1,0x00,0x00,0x1F,0x1F,0x1F,0x1F, - 0x1F,0x1F,0x1F,0x03,0x1F,0x1F,0x1F,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00, - 0x1F,0x1F,0x1F,0x1F,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, - 0x05,0x04,0x05,0x04,0x04,0x05,0x04,0x05,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, - 0x04,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, - 0x03,0x04,0x05,0x07 -}; -u8 intr_data[0x54] = { - 0x10,0x11,0x12,0x13,0x14,0x15,0x16,0x17,0x00,0x00,0x00,0x00,0x1F,0x1F,0x1F,0x1F, - 0x09,0x1F,0x1F,0x10,0x1F,0x10,0x1F,0x10,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00, - 0x05,0x1F,0x1F,0x1F,0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, - 0x12,0x11,0x12,0x11,0x12,0x11,0x12,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, - 0x11,0x13,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, - 0x10,0x11,0x12,0x13 -}; - -static void smp_add_mpc_entry(struct mp_config_table *mc, unsigned length) -{ - mc->mpc_length += length; - mc->mpc_entry_count++; -} - -static void my_smp_write_bus(struct mp_config_table *mc, - unsigned char id, const char *bustype) -{ - struct mpc_config_bus *mpc; - mpc = smp_next_mpc_entry(mc); - memset(mpc, '\0', sizeof(*mpc)); - mpc->mpc_type = MP_BUS; - mpc->mpc_busid = id; - memcpy(mpc->mpc_bustype, bustype, sizeof(mpc->mpc_bustype)); - smp_add_mpc_entry(mc, sizeof(*mpc)); -} +#include <southbridge/amd/common/amd_pci_util.h> static void *smp_write_config_table(void *v) { struct mp_config_table *mc; int bus_isa; - u8 byte; - - /* - * By the time this function gets called, the IOAPIC registers - * have been written so they can be read to get the correct - * APIC ID and Version - */ - u8 ioapic_id = (io_apic_read(VIO_APIC_VADDR, 0x00) >> 24); - u8 ioapic_ver = (io_apic_read(VIO_APIC_VADDR, 0x01) & 0xFF); + /* Intialize the MP_Table */ mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); mptable_init(mc, LOCAL_APIC_ADDR); - memcpy(mc->mpc_oem, "AMD ", 8); + /* + * Type 0: Processor Entries: + * LAPIC ID, LAPIC Version, CPU Flags:EN/BP, + * CPU Signature (Stepping, Model, Family), + * Feature Flags + */ smp_write_processors(mc); - //mptable_write_buses(mc, NULL, &bus_isa); - my_smp_write_bus(mc, 0, "PCI "); - my_smp_write_bus(mc, 1, "PCI "); - bus_isa = 0x02; - my_smp_write_bus(mc, bus_isa, "ISA "); + /* + * Type 1: Bus Entries: + * Bus ID, Bus Type + */ + mptable_write_buses(mc, NULL, &bus_isa); + + /* + * Type 2: I/O APICs: + * APIC ID, Version, APIC Flags:EN, Address + */ + u8 ioapic_id = (io_apic_read(VIO_APIC_VADDR, 0x00) >> 24); + u8 ioapic_ver = (io_apic_read(VIO_APIC_VADDR, 0x01) & 0xFF); - /* I/O APICs: APIC ID Version State Address */ smp_write_ioapic(mc, ioapic_id, ioapic_ver, VIO_APIC_VADDR); - smp_write_ioapic(mc, ioapic_id+1, 0x21, (void *)0xFEC20000); - /* PIC IRQ routine */ - for (byte = 0x0; byte < sizeof(picr_data); byte ++) { - outb(byte, 0xC00); - outb(picr_data[byte], 0xC01); - } - - /* APIC IRQ routine */ - for (byte = 0x0; byte < sizeof(intr_data); byte ++) { - outb(byte | 0x80, 0xC00); - outb(intr_data[byte], 0xC01); - } /* I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */ #define IO_LOCAL_INT(type, intr, apicid, pin) \ smp_write_lintsrc(mc, (type), MP_IRQ_TRIGGER_EDGE | MP_IRQ_POLARITY_HIGH, bus_isa, (intr), (apicid), (pin)); + + /* + * Type 3: I/O Interrupt Table Entries: + * Int Type, Int Polarity, Int Level, Source Bus ID, + * Source Bus IRQ, Dest APIC ID, Dest PIN# + */ + mptable_add_isa_interrupts(mc, bus_isa, ioapic_id, 0); /* PCI interrupts are level triggered, and are @@ -113,69 +77,47 @@ static void *smp_write_config_table(void *v) #define PCI_INT(bus, dev, int_sign, pin) \ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, (bus), (((dev)<<2)|(int_sign)), ioapic_id, (pin)) - /* Internal VGA */ - PCI_INT(0x0, 0x01, 0x0, intr_data[0x02]); - PCI_INT(0x0, 0x01, 0x1, intr_data[0x03]); + /* APU Internal Graphic Device */ + PCI_INT(0x0, 0x01, 0x0, intr_data_ptr[PIRQ_C]); + PCI_INT(0x0, 0x01, 0x1, intr_data_ptr[PIRQ_D]); - /* SMBUS */ - PCI_INT(0x0, 0x14, 0x0, 0x10); + /* SMBUS / ACPI */ + PCI_INT(0x0, 0x14, 0x0, intr_data_ptr[PIRQ_SMBUS]); - /* HD Audio */ - PCI_INT(0x0, 0x14, 0x0, intr_data[0x13]); + /* Southbridge HD Audio */ + PCI_INT(0x0, 0x14, 0x2, intr_data_ptr[PIRQ_HDA]); /* USB */ - PCI_INT(0x0, 0x12, 0x0, intr_data[0x30]); - PCI_INT(0x0, 0x12, 0x1, intr_data[0x31]); - PCI_INT(0x0, 0x13, 0x0, intr_data[0x32]); - PCI_INT(0x0, 0x13, 0x1, intr_data[0x33]); - PCI_INT(0x0, 0x16, 0x0, intr_data[0x34]); - PCI_INT(0x0, 0x16, 0x1, intr_data[0x35]); - PCI_INT(0x0, 0x14, 0x2, intr_data[0x36]); - - /* sata */ - PCI_INT(0x0, 0x11, 0x0, intr_data[0x40]); - PCI_INT(0x0, 0x11, 0x0, intr_data[0x41]); - - /* on board NIC & Slot PCIE. */ - - /* PCI slots */ - device_t dev = dev_find_slot(0, PCI_DEVFN(0x14, 4)); - if (dev && dev->enabled) { - u8 bus_pci = dev->link_list->secondary; - /* PCI_SLOT 0. */ - PCI_INT(bus_pci, 0x5, 0x0, 0x14); - PCI_INT(bus_pci, 0x5, 0x1, 0x15); - PCI_INT(bus_pci, 0x5, 0x2, 0x16); - PCI_INT(bus_pci, 0x5, 0x3, 0x17); - - /* PCI_SLOT 1. */ - PCI_INT(bus_pci, 0x6, 0x0, 0x15); - PCI_INT(bus_pci, 0x6, 0x1, 0x16); - PCI_INT(bus_pci, 0x6, 0x2, 0x17); - PCI_INT(bus_pci, 0x6, 0x3, 0x14); - - /* PCI_SLOT 2. */ - PCI_INT(bus_pci, 0x7, 0x0, 0x16); - PCI_INT(bus_pci, 0x7, 0x1, 0x17); - PCI_INT(bus_pci, 0x7, 0x2, 0x14); - PCI_INT(bus_pci, 0x7, 0x3, 0x15); - } + PCI_INT(0x0, 0x12, 0x0, intr_data_ptr[PIRQ_OHCI1]); + PCI_INT(0x0, 0x12, 0x1, intr_data_ptr[PIRQ_EHCI1]); + PCI_INT(0x0, 0x13, 0x0, intr_data_ptr[PIRQ_OHCI2]); + PCI_INT(0x0, 0x13, 0x1, intr_data_ptr[PIRQ_EHCI2]); + PCI_INT(0x0, 0x16, 0x0, intr_data_ptr[PIRQ_OHCI3]); + PCI_INT(0x0, 0x16, 0x1, intr_data_ptr[PIRQ_EHCI3]); + PCI_INT(0x0, 0x14, 0x2, intr_data_ptr[PIRQ_OHCI4]); + + /* SATA */ + PCI_INT(0x0, 0x11, 0x0, intr_data_ptr[PIRQ_SATA]); + + /* on board NIC & Slot PCIE */ + PCI_INT(0x1, 0x0, 0x0, intr_data_ptr[PIRQ_E]); + PCI_INT(0x2, 0x0, 0x0, intr_data_ptr[PIRQ_F]); /* PCIe Lan*/ - PCI_INT(0x0, 0x06, 0x0, 0x13); + PCI_INT(0x0, 0x06, 0x0, intr_data_ptr[PIRQ_D]); /* FCH PCIe PortA */ - PCI_INT(0x0, 0x15, 0x0, 0x10); + PCI_INT(0x0, 0x15, 0x0, intr_data_ptr[PIRQ_A]); /* FCH PCIe PortB */ - PCI_INT(0x0, 0x15, 0x1, 0x11); + PCI_INT(0x0, 0x15, 0x1, intr_data_ptr[PIRQ_B]); /* FCH PCIe PortC */ - PCI_INT(0x0, 0x15, 0x2, 0x12); + PCI_INT(0x0, 0x15, 0x2, intr_data_ptr[PIRQ_C]); /* FCH PCIe PortD */ - PCI_INT(0x0, 0x15, 0x3, 0x13); + PCI_INT(0x0, 0x15, 0x3, intr_data_ptr[PIRQ_D]); + + IO_LOCAL_INT(mp_ExtINT, 0x0, MP_APIC_ALL, 0x0); + IO_LOCAL_INT(mp_NMI, 0x0, MP_APIC_ALL, 0x1); - /*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */ - IO_LOCAL_INT(mp_ExtINT, 0, MP_APIC_ALL, 0x0); - IO_LOCAL_INT(mp_NMI, 0, MP_APIC_ALL, 0x1); /* There is no extension information... */ /* Compute the checksums */ @@ -185,6 +127,6 @@ static void *smp_write_config_table(void *v) unsigned long write_smp_table(unsigned long addr) { void *v; - v = smp_write_floating_table(addr, 0); + v = smp_write_floating_table(addr, 0); /* ADDR, Enable Virtual Wire */ return (unsigned long)smp_write_config_table(v); } diff --git a/src/mainboard/amd/db-ft3b-lc/romstage.c b/src/mainboard/amd/db-ft3b-lc/romstage.c index a5c529e7c5..c64fe4e3bc 100644 --- a/src/mainboard/amd/db-ft3b-lc/romstage.c +++ b/src/mainboard/amd/db-ft3b-lc/romstage.c @@ -68,16 +68,6 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val); printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx); - /* - * This refers to LpcClkDrvSth settling time. Without this setting, processor - * initialization is slow or incorrect, so this wait has been replicated from - * earlier development boards. - */ - { - int i; - for(i = 0; i < 200000; i++) inb(0xCD6); - } - post_code(0x37); AGESAWRAPPER(amdinitreset); |