diff options
| -rw-r--r-- | src/mainboard/google/brya/variants/joxer/gpio.c | 8 | ||||
| -rw-r--r-- | src/mainboard/google/brya/variants/joxer/overridetree.cb | 50 |
2 files changed, 57 insertions, 1 deletions
diff --git a/src/mainboard/google/brya/variants/joxer/gpio.c b/src/mainboard/google/brya/variants/joxer/gpio.c index ec7ef795f9..b1dcd4a83b 100644 --- a/src/mainboard/google/brya/variants/joxer/gpio.c +++ b/src/mainboard/google/brya/variants/joxer/gpio.c @@ -17,6 +17,9 @@ static const struct pad_config override_gpio_table[] = { /* B6 : SOC_I2C_SUB_SCL ==> NC */ PAD_NC_LOCK(GPP_B6, NONE, LOCK_CONFIG), + /* C1 : SMBDATA ==> TCHSCR_RST_L */ + PAD_CFG_GPO(GPP_C1, 1, DEEP), + /* D3 : WCAM_RST_L ==> NC */ PAD_NC_LOCK(GPP_D3, NONE, LOCK_CONFIG), /* D15 : EN_PP2800_WCAM_X ==> NC */ @@ -78,6 +81,11 @@ static const struct pad_config early_gpio_table[] = { }; static const struct pad_config romstage_gpio_table[] = { + /* Enable touchscreen, hold in reset */ + /* C0 : SMBCLK ==> EN_PP3300_TCHSCR_X */ + PAD_CFG_GPO(GPP_C0, 1, DEEP), + /* C1 : SMBDATA ==> TCHSCR_RST_L */ + PAD_CFG_GPO(GPP_C1, 0, DEEP), /* H12 : UART0_RTS# ==> SD_PERST_L */ PAD_CFG_GPO(GPP_H12, 1, DEEP), /* H20 : IMGCLKOUT1 ==> WLAN_PERST_L */ diff --git a/src/mainboard/google/brya/variants/joxer/overridetree.cb b/src/mainboard/google/brya/variants/joxer/overridetree.cb index e591b13dbd..dbfeb6d208 100644 --- a/src/mainboard/google/brya/variants/joxer/overridetree.cb +++ b/src/mainboard/google/brya/variants/joxer/overridetree.cb @@ -133,11 +133,59 @@ chip soc/intel/alderlake end end device ref i2c1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "detect" = "1" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "reset_delay_ms" = "20" + register "reset_off_delay_ms" = "2" + register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "stop_delay_ms" = "280" + register "stop_off_delay_ms" = "2" + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "enable_delay_ms" = "1" + register "has_power_resource" = "1" + device i2c 10 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN2513"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "20" + register "generic.reset_off_delay_ms" = "2" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_delay_ms" = "280" + register "generic.stop_off_delay_ms" = "2" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 15 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""GTCH7503"" + register "generic.desc" = ""G2TOUCH Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "50" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_delay_ms" = "30" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 40 on end + end chip drivers/i2c/hid register "generic.hid" = ""GDIX0000"" register "generic.desc" = ""Goodix Touchscreen"" register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" - register "generic.probed" = "1" + register "generic.detect" = "1" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "20" register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |