diff options
34 files changed, 837 insertions, 493 deletions
diff --git a/src/mainboard/kontron/986lcd-m/Config.lb b/src/mainboard/kontron/986lcd-m/Config.lb index 0dc004055c..eab88a9589 100644 --- a/src/mainboard/kontron/986lcd-m/Config.lb +++ b/src/mainboard/kontron/986lcd-m/Config.lb @@ -55,7 +55,8 @@ if CONFIG_GENERATE_ACPI_TABLES object acpi_tables.o makerule dsdt.c depends "$(CONFIG_MAINBOARD)/dsdt.asl" - action "iasl -p dsdt -tc $(CONFIG_MAINBOARD)/dsdt.asl" + action "$(CONFIG_CROSS_COMPILE)cpp -D__ACPI__ -P $(CPPFLAGS) -I$(CONFIG_MAINBOARD) $(CONFIG_MAINBOARD)/dsdt.asl -o $(CURDIR)/dsdt.asl" + action "iasl -p dsdt -tc $(CURDIR)/dsdt.asl" action "mv $(CURDIR)/dsdt.hex dsdt.c" end object ./dsdt.o @@ -150,7 +151,8 @@ chip northbridge/intel/i945 device pci_domain 0 on device pci 00.0 on end # host bridge - device pci 01.0 off end # i945 PCIe root port + # autodetect 0:1.0 because it might or might not be there. + # device pci 01.0 off end # i945 PCIe root port chip drivers/pci/onboard device pci 02.0 on end # vga controller # register "rom_address" = "0xfffc0000" # 256 KB image @@ -174,6 +176,7 @@ chip northbridge/intel/i945 # 1 SMI# (if corresponding ALT_GPI_SMI_EN bit is also set) # 2 SCI (if corresponding GPIO_EN bit is also set) register "gpi13_routing" = "1" + register "gpe0_en" = "0x00000400" register "ide_legacy_combined" = "0x1" register "ide_enable_primary" = "0x1" diff --git a/src/mainboard/kontron/986lcd-m/Kconfig b/src/mainboard/kontron/986lcd-m/Kconfig index 6ac6be2e2f..2af7401c55 100644 --- a/src/mainboard/kontron/986lcd-m/Kconfig +++ b/src/mainboard/kontron/986lcd-m/Kconfig @@ -43,7 +43,7 @@ config LB_CKS_LOC config MAINBOARD_PART_NUMBER string - default "986LCD-M/mITX" + default "986LCD-M" depends on BOARD_KONTRON_986LCD_M config MMCONF_BASE_ADDRESS diff --git a/src/mainboard/kontron/986lcd-m/Makefile.inc b/src/mainboard/kontron/986lcd-m/Makefile.inc index 61acbe68ca..5cd84bcde7 100644 --- a/src/mainboard/kontron/986lcd-m/Makefile.inc +++ b/src/mainboard/kontron/986lcd-m/Makefile.inc @@ -56,7 +56,8 @@ ldscript-y += ../../../../src/arch/i386/lib/failover.lds ifdef POST_EVALUATION $(obj)/dsdt.c: $(src)/mainboard/$(MAINBOARDDIR)/dsdt.asl - iasl -p dsdt -tc $(src)/mainboard/$(MAINBOARDDIR)/dsdt.asl + $(CPP) -D__ACPI__ -P $(CPPFLAGS) -include $(obj)/config.h -I$(src)/mainboard/$(MAINBOARDDIR) $(src)/mainboard/$(MAINBOARDDIR)/dsdt.asl -o $(obj)/dsdt.asl + iasl -p dsdt -tc $(obj)/dsdt.asl mv dsdt.hex $@ $(obj)/mainboard/$(MAINBOARDDIR)/dsdt.o: $(obj)/dsdt.c diff --git a/src/mainboard/kontron/986lcd-m/Options.lb b/src/mainboard/kontron/986lcd-m/Options.lb index feb26a666a..811d8efdb3 100644 --- a/src/mainboard/kontron/986lcd-m/Options.lb +++ b/src/mainboard/kontron/986lcd-m/Options.lb @@ -312,7 +312,7 @@ default CONFIG_TTYS0_LCS=0x3 ## WARNING 5 warning conditions ## NOTICE 6 normal but significant condition ## INFO 7 informational -## CONFIG_DEBUG 8 debug-level messages +## DEBUG 8 debug-level messages ## SPEW 9 Way too many details ## Request this level of debugging output diff --git a/src/mainboard/kontron/986lcd-m/acpi/superio.asl b/src/mainboard/kontron/986lcd-m/acpi/superio.asl index d2498d4e5b..bb927afb01 100644 --- a/src/mainboard/kontron/986lcd-m/acpi/superio.asl +++ b/src/mainboard/kontron/986lcd-m/acpi/superio.asl @@ -29,7 +29,30 @@ Device (SIO1) { Name(_HID, EISAID("PNP0501")) Name(_UID, 1) + Name(_DDN, "COM1") + Method (_STA, 0) + { + // always enable for now + Return (0x0f) + } + + Method (_DIS, 0) { /* NOOP */ } + + Name (_PRS, ResourceTemplate() { + StartDependentFn(0, 1) { + IO(Decode16, 0x3f8, 0x3f8, 0x8, 0x8) + IRQNoFlags() { 4 } + } EndDependentFn() + }) + + Method (_CRS, 0) + { + Return(ResourceTemplate() { + IO(Decode16, 0x3f8, 0x3f8, 0x8, 0x8) + IRQNoFlags() { 4 } + }) + } // Some methods need an implementation here: // missing: _STA, _DIS, _CRS, _PRS, // missing: _SRS, _PS0, _PS3 @@ -39,7 +62,30 @@ Device (SIO1) { Name(_HID, EISAID("PNP0501")) Name(_UID, 2) + Name(_DDN, "COM2") + + Method (_STA, 0) + { + // always enable for now + Return (0x0f) + } + + Method (_DIS, 0) { /* NOOP */ } + + Name (_PRS, ResourceTemplate() { + StartDependentFn(0, 1) { + IO(Decode16, 0x2f8, 0x2f8, 0x8, 0x8) + IRQNoFlags() { 3 } + } EndDependentFn() + }) + Method (_CRS, 0) + { + Return(ResourceTemplate() { + IO(Decode16, 0x2f8, 0x2f8, 0x8, 0x8) + IRQNoFlags() { 3 } + }) + } // Some methods need an implementation here: // missing: _STA, _DIS, _CRS, _PRS, // missing: _SRS, _PS0, _PS3 diff --git a/src/mainboard/kontron/986lcd-m/acpi_tables.c b/src/mainboard/kontron/986lcd-m/acpi_tables.c index 27942e3499..68f3d9cbf9 100644 --- a/src/mainboard/kontron/986lcd-m/acpi_tables.c +++ b/src/mainboard/kontron/986lcd-m/acpi_tables.c @@ -31,100 +31,33 @@ #include <cpu/x86/msr.h> #include "dmi.h" -#define OLD_ACPI 0 - extern unsigned char AmlCode[]; #if HAVE_ACPI_SLIC unsigned long acpi_create_slic(unsigned long current); #endif void generate_cpu_entries(void); // from cpu/intel/speedstep -unsigned long acpi_fill_mcfg(unsigned long current); // from northbridge/intel/i945 - -#if OLD_ACPI -typedef struct acpi_oemb { - acpi_header_t header; - u8 ss; - u16 iost; - u32 topm; - u32 roms; - u32 mg1b; - u32 mg1l; - u32 mg2b; - u32 mg2l; - u8 rsvd; - u8 dmax; - u32 hpta; - u32 cpb0; - u32 cpb1; - u32 cpb2; - u32 cpb3; - u8 assb; - u8 aotb; - u32 aaxb; - u8 smif; - u8 dtse; - u8 dts1; - u8 dts2; - u8 mpen; -} __attribute__((packed)) acpi_oemb_t; -#endif - -typedef struct acpi_gnvs { - // 0x00 - u16 osys; - u8 smif; - u8 reserved[13]; - // 0x10 - u8 mpen; -} __attribute__((packed)) acpi_gnvs_t; - -#if OLD_ACPI -void acpi_create_oemb(acpi_oemb_t *oemb) -{ - acpi_header_t *header = &(oemb->header); - unsigned long tolud; - - memset (oemb, 0, sizeof(*oemb)); - - /* fill out header fields */ - memcpy(header->signature, "OEMB", 4); - memcpy(header->oem_id, OEM_ID, 6); - memcpy(header->oem_table_id, "COREBOOT", 8); - memcpy(header->asl_compiler_id, ASLC, 4); - - header->length = sizeof(acpi_oemb_t); - header->revision = 1; - - oemb->ss = 0x09; // ss1 + ss 4 - oemb->iost = 0x0403; // ?? - - tolud = pci_read_config32(dev_find_slot(0, PCI_DEVFN(2, 0)), 0x5c); - oemb->topm = tolud; - - oemb->roms = 0xfff00000; // 1M hardcoded - - oemb->mg1b = 0x000d0000; - oemb->mg1l = 0x00010000; - oemb->mg2b = tolud; - oemb->mg2l = 0-tolud; - - oemb->dmax = 0x87; - oemb->hpta = 0x000e36c0; - - header->checksum = - acpi_checksum((void *) oemb, sizeof(acpi_oemb_t)); - -}; -#endif - -void acpi_create_gnvs(acpi_gnvs_t *gnvs) +#include "../../../southbridge/intel/i82801gx/i82801gx_nvs.h" +static void acpi_create_gnvs(global_nvs_t *gnvs) { memset((void *)gnvs, 0, sizeof(*gnvs)); - gnvs->mpen = 1; + gnvs->apic = 1; + gnvs->mpen = 1; /* Enable Multi Processing */ + + /* Enable both COM ports */ + gnvs->cmap = 0x01; + gnvs->cmbp = 0x01; + + /* IGD Displays */ + gnvs->ndid = 3; + gnvs->did[0] = 0x80000100; + gnvs->did[1] = 0x80000240; + gnvs->did[2] = 0x80000410; + gnvs->did[3] = 0x80000410; + gnvs->did[4] = 0x00000005; } -void acpi_create_intel_hpet(acpi_hpet_t * hpet) +static void acpi_create_intel_hpet(acpi_hpet_t * hpet) { #define HPET_ADDR 0xfed00000ULL acpi_header_t *header = &(hpet->header); @@ -212,10 +145,6 @@ unsigned long write_acpi_tables(unsigned long start) #if HAVE_ACPI_SLIC acpi_header_t *slic; #endif -#if OLD_ACPI - acpi_oemb_t *oemb; -#endif - acpi_gnvs_t *gnvs; acpi_header_t *ssdt; acpi_header_t *dsdt; @@ -271,15 +200,6 @@ unsigned long write_acpi_tables(unsigned long start) ALIGN_CURRENT; acpi_add_table(rsdp, mcfg); -#if OLD_ACPI - printk_debug("ACPI: * OEMB\n"); - oemb=(acpi_oemb_t *)current; - current += sizeof(acpi_oemb_t); - ALIGN_CURRENT; - acpi_create_oemb(oemb); - acpi_add_table(rsdp, oemb); -#endif - printk_debug("ACPI: * FACS\n"); facs = (acpi_facs_t *) current; current += sizeof(acpi_facs_t); @@ -291,16 +211,6 @@ unsigned long write_acpi_tables(unsigned long start) memcpy((void *) dsdt, (void *) AmlCode, ((acpi_header_t *) AmlCode)->length); -#if OLD_ACPI - for (i=0; i < dsdt->length; i++) { - if (*(u32*)(((u32)dsdt) + i) == 0xC0DEBEEF) { - printk_debug("ACPI: Patching up DSDT at offset 0x%04x -> 0x%08x\n", i, 0x24 + (u32)oemb); - *(u32*)(((u32)dsdt) + i) = 0x24 + (u32)oemb; - break; - } - } -#endif - ALIGN_CURRENT; /* Pack GNVS into the ACPI table area */ diff --git a/src/mainboard/kontron/986lcd-m/auto.c b/src/mainboard/kontron/986lcd-m/auto.c index d83f0fec2a..003fdb393f 100644 --- a/src/mainboard/kontron/986lcd-m/auto.c +++ b/src/mainboard/kontron/986lcd-m/auto.c @@ -1,7 +1,7 @@ /* * This file is part of the coreboot project. * - * Copyright (C) 2007-2008 coresystems GmbH + * Copyright (C) 2007-2009 coresystems GmbH * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -57,7 +57,6 @@ #include "southbridge/intel/i82801gx/i82801gx.h" static void setup_ich7_gpios(void) { - /* TODO: This is highly board specific and should be moved */ printk_debug(" GPIOS..."); /* General Registers */ outl(0x1f1ff7c0, DEFAULT_GPIOBASE + 0x00); /* GPIO_USE_SEL */ @@ -127,6 +126,12 @@ static void early_superio_config_w83627thg(void) dev=PNP_DEV(0x2e, W83627THG_SP1); pnp_enter_ext_func_mode(dev); + pnp_write_config(dev, 0x24, 0xc6); // PNPCSV + + pnp_write_config(dev, 0x29, 0x43); // GPIO settings + pnp_write_config(dev, 0x2a, 0x40); // GPIO settings + + dev=PNP_DEV(0x2e, W83627THG_SP1); pnp_set_logical_device(dev); pnp_set_enable(dev, 0); pnp_set_iobase(dev, PNP_IDX_IO0, 0x3f8); @@ -218,6 +223,8 @@ static void early_superio_config_w83627thg(void) static void rcba_config(void) { + u32 reg32; + /* Set up virtual channel 0 */ //RCBA32(0x0014) = 0x80000001; //RCBA32(0x001c) = 0x03128010; @@ -240,9 +247,52 @@ static void rcba_config(void) /* Enable upper 128bytes of CMOS */ RCBA32(0x3400) = (1 << 2); + /* Now, this is a bit ugly. As per PCI specification, function 0 of a + * device always has to be implemented. So disabling ethernet port 1 + * would essentially disable all three ethernet ports of the mainboard. + * It's possible to rename the ports to achieve compatibility to the + * PCI spec but this will confuse all (static!) tables containing + * interrupt routing information. + * To avoid this, we enable (unused) port 6 and swap it with port 1 + * in the case that ethernet port 1 is disabled. Since no devices + * are connected to that port, we don't have to worry about interrupt + * routing. + */ + int port_shuffle = 0; + /* Disable unused devices */ - RCBA32(0x3418) = FD_PCIE6|FD_PCIE5|FD_PCIE4|FD_ACMOD|FD_ACAUD|FD_PATA; - RCBA32(0x3418) |= (1 << 0); // Required. + reg32 = FD_ACMOD|FD_ACAUD|FD_PATA; + reg32 |= FD_PCIE6|FD_PCIE5|FD_PCIE4; + + if (read_option(CMOS_VSTART_ethernet1, CMOS_VLEN_ethernet1, 0) != 0) { + printk_debug("Disabling ethernet adapter 1.\n"); + reg32 |= FD_PCIE1; + } + if (read_option(CMOS_VSTART_ethernet2, CMOS_VLEN_ethernet2, 0) != 0) { + printk_debug("Disabling ethernet adapter 2.\n"); + reg32 |= FD_PCIE2; + } else { + if (reg32 & FD_PCIE1) + port_shuffle = 1; + } + if (read_option(CMOS_VSTART_ethernet3, CMOS_VLEN_ethernet3, 0) != 0) { + printk_debug("Disabling ethernet adapter 3.\n"); + reg32 |= FD_PCIE3; + } else { + if (reg32 & FD_PCIE1) + port_shuffle = 1; + } + + if (port_shuffle) { + /* Enable PCIE6 again */ + reg32 &= ~FD_PCIE6; + /* Swap PCIE6 and PCIE1 */ + RCBA32(RPFN) = 0x00043215; + } + + reg32 |= 1; + + RCBA32(0x3418) = reg32; /* Enable PCIe Root Port Clock Gate */ // RCBA32(0x341c) = 0x00000001; @@ -306,6 +356,16 @@ static void early_ich7_init(void) #include "southbridge/intel/i82801gx/cmos_failover.c" #endif +#include <cbmem.h> + +// Now, this needs to be included because it relies on the symbol +// __ROMCC_ being set during CAR stage (in order to compile the +// BSS free versions of the functions). Either rewrite the code +// to be always BSS free, or invent a flag that's better suited than +// __ROMCC__ to determine whether we're in ram init stage (stage 1) +// +#include "lib/cbmem.c" + void real_main(unsigned long bist) { u32 reg32; @@ -345,13 +405,14 @@ void real_main(unsigned long bist) reg32 = inl(DEFAULT_PMBASE + 0x04); printk_debug("PM1_CNT: %08x\n", reg32); if (((reg32 >> 10) & 7) == 5) { -#if HAVE_ACPI_RESUME +#if CONFIG_HAVE_ACPI_RESUME printk_debug("Resume from S3 detected.\n"); boot_mode = 2; /* Clear SLP_TYPE. This will break stage2 but * we care for that when we get there. */ outl(reg32 & ~(7 << 10), DEFAULT_PMBASE + 0x04); + #else printk_debug("Resume from S3 detected, but disabled.\n"); #endif @@ -380,6 +441,7 @@ void real_main(unsigned long bist) /* Initialize the internal PCIe links before we go into stage2 */ i945_late_initialization(); +#if !CONFIG_HAVE_ACPI_RESUME #if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8 #if defined(DEBUG_RAM_SETUP) sdram_dump_mchbar_registers(); @@ -391,10 +453,35 @@ void real_main(unsigned long bist) printk_debug("TOM: 0x%08x\n", tom); ram_check(0x00000000, 0x000a0000); - ram_check(0x00100000, tom); + //ram_check(0x00100000, tom); } #endif +#endif + MCHBAR16(SSKPD) = 0xCAFE; + +#if CONFIG_HAVE_ACPI_RESUME + /* Start address of high memory tables */ + unsigned long high_ram_base = get_top_of_ram() - HIGH_MEMORY_SIZE; + + /* If there is no high memory area, we didn't boot before, so + * this is not a resume. In that case we just create the cbmem toc. + */ + if ((boot_mode == 2) && cbmem_reinit((u64)high_ram_base)) { + void *resume_backup_memory = cbmem_find(CBMEM_ID_RESUME); + + /* copy 1MB - 64K to high tables ram_base to prevent memory corruption + * through stage 2. We could keep stuff like stack and heap in high tables + * memory completely, but that's a wonderful clean up task for another + * day. + */ + if (resume_backup_memory) + memcpy(resume_backup_memory, CONFIG_RAMBASE, HIGH_MEMORY_SAVE); + + /* Magic for S3 resume */ + pci_write_config32(PCI_DEV(0, 0x00, 0), SKPAD, 0xcafed00d); + } +#endif } #include "cpu/intel/model_6ex/cache_as_ram_disable.c" diff --git a/src/mainboard/kontron/986lcd-m/cmos.layout b/src/mainboard/kontron/986lcd-m/cmos.layout index a53381c7a3..1a19018b5e 100644 --- a/src/mainboard/kontron/986lcd-m/cmos.layout +++ b/src/mainboard/kontron/986lcd-m/cmos.layout @@ -91,7 +91,21 @@ entries # coreboot config options: bootloader 416 512 s 0 boot_devices -#928 80 r 0 unused +#928 40 r 0 unused + +# coreboot config options: mainboard specific options +948 2 e 8 cpufan_cruise_control +950 2 e 8 sysfan_cruise_control +952 4 e 9 cpufan_speed +#956 4 e 10 cpufan_temperature +960 4 e 9 sysfan_speed +#964 4 e 10 sysfan_temperature + +968 1 e 2 ethernet1 +969 1 e 2 ethernet2 +970 1 e 2 ethernet3 + +#971 13 r 0 unused # coreboot config options: check sums 984 16 h 0 check_sum @@ -135,7 +149,45 @@ enumerations 7 0 Disable 7 1 Enable 7 2 Keep - +# Fan Cruise Control +8 0 Disabled +8 1 Speed +#8 2 Thermal +# Fan Speed (Rotations per Minute) +9 0 5625 +9 1 5192 +9 2 4753 +9 3 4326 +9 4 3924 +9 5 3552 +9 6 3214 +9 7 2909 +9 8 2636 +9 9 2393 +9 10 2177 +9 11 1985 +9 12 1814 +9 13 1662 +9 14 1527 +9 15 1406 +# +# Temperature (°C/°F) +#10 0 30/86 +#10 1 33/91 +#10 2 36/96 +#10 3 39/102 +#10 4 42/107 +#10 5 45/113 +#10 6 48/118 +#10 7 51/123 +#10 8 54/129 +#10 9 57/134 +#10 10 60/140 +#10 11 63/145 +#10 12 66/150 +#10 13 69/156 +#10 14 72/161 +#10 15 75/167 # ----------------------------------------------------------------- checksums diff --git a/src/mainboard/kontron/986lcd-m/dsdt.asl b/src/mainboard/kontron/986lcd-m/dsdt.asl index f12e16b9a4..04a658fe90 100644 --- a/src/mainboard/kontron/986lcd-m/dsdt.asl +++ b/src/mainboard/kontron/986lcd-m/dsdt.asl @@ -29,24 +29,24 @@ DefinitionBlock( ) { // Some generic macros - Include ("acpi/platform.asl") + #include "acpi/platform.asl" // global NVS and variables - Include ("../../../southbridge/intel/i82801gx/acpi/globalnvs.asl") + #include "../../../southbridge/intel/i82801gx/acpi/globalnvs.asl" // General Purpose Events - //include ("acpi/gpe.asl") + //#include "acpi/gpe.asl" - //include ("acpi/thermal.asl") + //#include "acpi/thermal.asl" Scope (\_SB) { Device (PCI0) { - Include ("../../../northbridge/intel/i945/acpi/i945.asl") - include ("../../../southbridge/intel/i82801gx/acpi/ich7.asl") + #include "../../../northbridge/intel/i945/acpi/i945.asl" + #include "../../../southbridge/intel/i82801gx/acpi/ich7.asl" } } /* Chipset specific sleep states */ - include ("../../../southbridge/intel/i82801gx/acpi/sleepstates.asl") + #include "../../../southbridge/intel/i82801gx/acpi/sleepstates.asl" } diff --git a/src/mainboard/kontron/986lcd-m/fadt.c b/src/mainboard/kontron/986lcd-m/fadt.c index e8677e1015..72d94332ef 100644 --- a/src/mainboard/kontron/986lcd-m/fadt.c +++ b/src/mainboard/kontron/986lcd-m/fadt.c @@ -1,7 +1,7 @@ /* * This file is part of the coreboot project. * - * Copyright (C) 2007-2008 coresystems GmbH + * Copyright (C) 2007-2009 coresystems GmbH * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -23,13 +23,13 @@ #include <device/pci.h> #include <arch/acpi.h> -/* FIXME: This needs to go into a separate .h file +/* FIXME: This needs to go into a separate .h file * to be included by the ich7 smi handler, ich7 smi init * code and the mainboard fadt. */ #define APM_CNT 0xb2 -#define CST_CONTROL 0x00 // 0xe3 crashes the box -#define PST_CONTROL 0x00 // 0xe2 crashes the box +#define CST_CONTROL 0x85 +#define PST_CONTROL 0x80 #define ACPI_DISABLE 0x1e #define ACPI_ENABLE 0xe1 #define GNVS_UPDATE 0xea @@ -59,7 +59,7 @@ void acpi_create_fadt(acpi_fadt_t * fadt, acpi_facs_t * facs, void *dsdt) fadt->acpi_disable = ACPI_DISABLE; fadt->s4bios_req = 0x0; fadt->pstate_cnt = PST_CONTROL; - + fadt->pm1a_evt_blk = pmbase; fadt->pm1b_evt_blk = 0x0; fadt->pm1a_cnt_blk = pmbase + 0x4; @@ -89,72 +89,72 @@ void acpi_create_fadt(acpi_fadt_t * fadt, acpi_facs_t * facs, void *dsdt) fadt->century = 0x00; fadt->iapc_boot_arch = 0x03; - fadt->flags = ACPI_FADT_WBINVD | ACPI_FADT_C1_SUPPORTED | - ACPI_FADT_C2_MP_SUPPORTED | ACPI_FADT_SLEEP_BUTTON | + fadt->flags = ACPI_FADT_WBINVD | ACPI_FADT_C1_SUPPORTED | + ACPI_FADT_C2_MP_SUPPORTED | ACPI_FADT_SLEEP_BUTTON | ACPI_FADT_S4_RTC_WAKE | ACPI_FADT_PLATFORM_CLOCK; - + fadt->reset_reg.space_id = 0; fadt->reset_reg.bit_width = 0; fadt->reset_reg.bit_offset = 0; fadt->reset_reg.resv = 0; fadt->reset_reg.addrl = 0x0; fadt->reset_reg.addrh = 0x0; - + fadt->reset_value = 0; fadt->x_firmware_ctl_l = (unsigned long)facs; fadt->x_firmware_ctl_h = 0; fadt->x_dsdt_l = (unsigned long)dsdt; fadt->x_dsdt_h = 0; - + fadt->x_pm1a_evt_blk.space_id = 1; fadt->x_pm1a_evt_blk.bit_width = 32; fadt->x_pm1a_evt_blk.bit_offset = 0; fadt->x_pm1a_evt_blk.resv = 0; fadt->x_pm1a_evt_blk.addrl = pmbase; fadt->x_pm1a_evt_blk.addrh = 0x0; - + fadt->x_pm1b_evt_blk.space_id = 1; fadt->x_pm1b_evt_blk.bit_width = 0; fadt->x_pm1b_evt_blk.bit_offset = 0; fadt->x_pm1b_evt_blk.resv = 0; fadt->x_pm1b_evt_blk.addrl = 0x0; fadt->x_pm1b_evt_blk.addrh = 0x0; - + fadt->x_pm1a_cnt_blk.space_id = 1; fadt->x_pm1a_cnt_blk.bit_width = 16; fadt->x_pm1a_cnt_blk.bit_offset = 0; fadt->x_pm1a_cnt_blk.resv = 0; fadt->x_pm1a_cnt_blk.addrl = pmbase + 0x4; fadt->x_pm1a_cnt_blk.addrh = 0x0; - + fadt->x_pm1b_cnt_blk.space_id = 1; fadt->x_pm1b_cnt_blk.bit_width = 0; fadt->x_pm1b_cnt_blk.bit_offset = 0; fadt->x_pm1b_cnt_blk.resv = 0; fadt->x_pm1b_cnt_blk.addrl = 0x0; fadt->x_pm1b_cnt_blk.addrh = 0x0; - + fadt->x_pm2_cnt_blk.space_id = 1; fadt->x_pm2_cnt_blk.bit_width = 8; fadt->x_pm2_cnt_blk.bit_offset = 0; fadt->x_pm2_cnt_blk.resv = 0; fadt->x_pm2_cnt_blk.addrl = pmbase + 0x20; fadt->x_pm2_cnt_blk.addrh = 0x0; - + fadt->x_pm_tmr_blk.space_id = 1; fadt->x_pm_tmr_blk.bit_width = 32; fadt->x_pm_tmr_blk.bit_offset = 0; fadt->x_pm_tmr_blk.resv = 0; fadt->x_pm_tmr_blk.addrl = pmbase + 0x8; fadt->x_pm_tmr_blk.addrh = 0x0; - + fadt->x_gpe0_blk.space_id = 1; fadt->x_gpe0_blk.bit_width = 64; fadt->x_gpe0_blk.bit_offset = 0; fadt->x_gpe0_blk.resv = 0; fadt->x_gpe0_blk.addrl = pmbase + 0x28; fadt->x_gpe0_blk.addrh = 0x0; - + fadt->x_gpe1_blk.space_id = 1; fadt->x_gpe1_blk.bit_width = 0; fadt->x_gpe1_blk.bit_offset = 0; diff --git a/src/mainboard/kontron/986lcd-m/mainboard.c b/src/mainboard/kontron/986lcd-m/mainboard.c index 4cc883efeb..9a2a5fdc5c 100644 --- a/src/mainboard/kontron/986lcd-m/mainboard.c +++ b/src/mainboard/kontron/986lcd-m/mainboard.c @@ -1,7 +1,7 @@ /* * This file is part of the coreboot project. * - * Copyright (C) 2007-2008 coresystems GmbH + * Copyright (C) 2007-2009 coresystems GmbH * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -19,10 +19,12 @@ * MA 02110-1301 USA */ - +#include <types.h> #include <device/device.h> #include <console/console.h> #include <boot/tables.h> +#include <pc80/mc146818rtc.h> +#include <arch/io.h> #include "chip.h" int add_northbridge_resources(struct lb_memory *mem); @@ -32,7 +34,162 @@ int add_mainboard_resources(struct lb_memory *mem) return add_northbridge_resources(mem); } +/* Hardware Monitor */ + +static u16 hwm_base = 0xa00; + +static void hwm_write(u8 reg, u8 value) +{ + outb(reg, hwm_base + 0x05); + outb(value, hwm_base + 0x06); +} + +static void hwm_bank(u8 bank) +{ + hwm_write(0x4e, bank); +} + +#define FAN_CRUISE_CONTROL_DISABLED 0 +#define FAN_CRUISE_CONTROL_SPEED 1 +#define FAN_CRUISE_CONTROL_THERMAL 2 + +#define FAN_SPEED_5625 0 +//#define FAN_TEMPERATURE_30DEGC 0 + +struct fan_speed { + u8 fan_in; + u16 fan_speed; +}; + +// FANIN Target Speed Register +// FANIN = 337500 / RPM +struct fan_speed fan_speeds[] = { + { 0x3c, 5625 }, { 0x41, 5192 }, { 0x47, 4753 }, { 0x4e, 4326 }, + { 0x56, 3924 }, { 0x5f, 3552 }, { 0x69, 3214 }, { 0x74, 2909 }, + { 0x80, 2636 }, { 0x8d, 2393 }, { 0x9b, 2177 }, { 0xaa, 1985 }, + { 0xba, 1814 }, { 0xcb, 1662 }, { 0xdd, 1527 }, { 0xf0, 1406 } +}; + +struct temperature { + u8 deg_celsius; + u8 deg_fahrenheit; +}; + +struct temperature temperatures[] = { + { 30, 86 }, { 33, 91 }, { 36, 96 }, { 39, 102 }, + { 42, 107 }, { 45, 113 }, { 48, 118 }, { 51, 123 }, + { 54, 129 }, { 57, 134 }, { 60, 140 }, { 63, 145 }, + { 66, 150 }, { 69, 156 }, { 72, 161 }, { 75, 167 } +}; + +static void hwm_setup(void) +{ + int cpufan_control = 0, sysfan_control = 0; + int cpufan_speed = 0, sysfan_speed = 0; + int cpufan_temperature = 0, sysfan_temperature = 0; + + if (get_option(&cpufan_control, "cpufan_cruise_control") < 0) + cpufan_control = FAN_CRUISE_CONTROL_DISABLED; + if (get_option(&cpufan_speed, "cpufan_speed") < 0) + cpufan_speed = FAN_SPEED_5625; + //if (get_option(&cpufan_temperature, "cpufan_temperature") < 0) + // cpufan_temperature = FAN_TEMPERATURE_30DEGC; + + if (get_option(&sysfan_control, "sysfan_cruise_control") < 0) + sysfan_control = FAN_CRUISE_CONTROL_DISABLED; + if (get_option(&sysfan_speed, "sysfan_speed") < 0) + sysfan_speed = FAN_SPEED_5625; + //if (get_option(&sysfan_temperature, "sysfan_temperature") < 0) + // sysfan_temperature = FAN_TEMPERATURE_30DEGC; + + // hwm_write(0x31, 0x20); // AVCC high limit + // hwm_write(0x34, 0x06); // VIN2 low limit + + hwm_bank(0); + hwm_write(0x59, 0x20); // Diode Selection + hwm_write(0x5d, 0x0f); // All Sensors Diode, not Thermistor + + hwm_bank(4); + hwm_write(0x54, 0xf1); // SYSTIN temperature offset + hwm_write(0x55, 0x19); // CPUTIN temperature offset + hwm_write(0x56, 0xfc); // AUXTIN temperature offset + + hwm_bank(0x80); // Default + + u8 fan_config = 0; + // 00 FANOUT is Manual Mode + // 01 FANOUT is Thermal Cruise Mode + // 10 FANOUT is Fan Speed Cruise Mode + switch (cpufan_control) { + case FAN_CRUISE_CONTROL_SPEED: fan_config |= (2 << 4); break; + case FAN_CRUISE_CONTROL_THERMAL: fan_config |= (1 << 4); break; + } + switch (sysfan_control) { + case FAN_CRUISE_CONTROL_SPEED: fan_config |= (2 << 2); break; + case FAN_CRUISE_CONTROL_THERMAL: fan_config |= (1 << 2); break; + } + // This register must be written first + hwm_write(0x04, fan_config); + + switch (cpufan_control) { + case FAN_CRUISE_CONTROL_SPEED: + printk_debug("Fan Cruise Control setting CPU fan to %d RPM\n", + fan_speeds[cpufan_speed].fan_speed); + hwm_write(0x06, fan_speeds[cpufan_speed].fan_in); // CPUFANIN target speed + break; + case FAN_CRUISE_CONTROL_THERMAL: + printk_debug("Fan Cruise Control setting CPU fan to activation at %d deg C/%d deg F\n", + temperatures[cpufan_temperature].deg_celsius, + temperatures[cpufan_temperature].deg_fahrenheit); + hwm_write(0x06, temperatures[cpufan_temperature].deg_celsius); // CPUFANIN target temperature + break; + } + + switch (sysfan_control) { + case FAN_CRUISE_CONTROL_SPEED: + printk_debug("Fan Cruise Control setting system fan to %d RPM\n", + fan_speeds[sysfan_speed].fan_speed); + hwm_write(0x05, fan_speeds[sysfan_speed].fan_in); // SYSFANIN target speed + break; + case FAN_CRUISE_CONTROL_THERMAL: + printk_debug("Fan Cruise Control setting system fan to activation at %d deg C/%d deg F\n", + temperatures[sysfan_temperature].deg_celsius, + temperatures[sysfan_temperature].deg_fahrenheit); + hwm_write(0x05, temperatures[sysfan_temperature].deg_celsius); // SYSFANIN target temperature + break; + } + + hwm_write(0x0e, 0x02); // Fan Output Step Down Time + hwm_write(0x0f, 0x02); // Fan Output Step Up Time + + hwm_write(0x47, 0xaf); // FAN divisor register + hwm_write(0x4b, 0x84); // AUXFANIN speed divisor + + hwm_write(0x40, 0x01); // Init, but no SMI# +} + +/* Audio Setup */ + +extern u32 * cim_verb_data; +extern u32 cim_verb_data_size; + +static void verb_setup(void) +{ + // Default VERB is fine on this mainboard. + cim_verb_data = NULL; + cim_verb_data_size = 0; +} + +// mainboard_enable is executed as first thing after +// enumerate_buses(). +static void mainboard_enable(device_t dev) +{ + verb_setup(); + hwm_setup(); +} + struct chip_operations mainboard_ops = { CHIP_NAME("Kontron 986LCD-M Mainboard") + .enable_dev = mainboard_enable, }; diff --git a/src/northbridge/intel/i945/acpi.c b/src/northbridge/intel/i945/acpi.c index 23aadd5752..2640cca3f6 100644 --- a/src/northbridge/intel/i945/acpi.c +++ b/src/northbridge/intel/i945/acpi.c @@ -27,6 +27,7 @@ #include <device/device.h> #include <device/pci.h> #include <device/pci_ids.h> +#include "i945.h" unsigned long acpi_fill_mcfg(unsigned long current) { @@ -39,7 +40,7 @@ unsigned long acpi_fill_mcfg(unsigned long current) if (!dev) return current; - pciexbar_reg=pci_read_config32(dev, 0x48); + pciexbar_reg=pci_read_config32(dev, PCIEXBAR); // MMCFG not supported or not enabled. if (!(pciexbar_reg & (1 << 0))) diff --git a/src/northbridge/intel/i945/acpi/i945.asl b/src/northbridge/intel/i945/acpi/i945.asl index 420ba0e592..9511925a69 100644 --- a/src/northbridge/intel/i945/acpi/i945.asl +++ b/src/northbridge/intel/i945/acpi/i945.asl @@ -19,7 +19,8 @@ * MA 02110-1301 USA */ -Include ("../../../northbridge/intel/i945/acpi/i945_hostbridge.asl") +#include "../../../northbridge/intel/i945/acpi/i945_hostbridge.asl" +#include "../../../northbridge/intel/i945/i945.h" /* PCI Device Resource Consumption */ Device (PDRC) @@ -41,10 +42,10 @@ Device (PDRC) Name (PDRS, ResourceTemplate() { Memory32Fixed(ReadWrite, 0xfed1c000, 0x00004000) // RCBA - Memory32Fixed(ReadWrite, 0xfed14000, 0x00004000) // MCHBAR - Memory32Fixed(ReadWrite, 0xfed18000, 0x00001000) // DMIBAR - Memory32Fixed(ReadWrite, 0xfed19000, 0x00001000) // EPBAR - Memory32Fixed(ReadWrite, 0xf0000000, 0x04000000) // PCIE BAR + Memory32Fixed(ReadWrite, DEFAULT_MCHBAR, 0x00004000) + Memory32Fixed(ReadWrite, DEFAULT_DMIBAR, 0x00001000) + Memory32Fixed(ReadWrite, DEFAULT_EPBAR, 0x00001000) + Memory32Fixed(ReadWrite, DEFAULT_PCIEXBAR, 0x04000000) Memory32Fixed(ReadWrite, 0xfed20000, 0x00020000) // Misc ICH Memory32Fixed(ReadWrite, 0xfed40000, 0x00005000) // Misc ICH Memory32Fixed(ReadWrite, 0xfed45000, 0x0004b000) // Misc ICH @@ -76,13 +77,13 @@ Device (PDRC) } // PCIe graphics port 0:1.0 -Include ("../../../northbridge/intel/i945/acpi/i945_peg.asl") +#include "../../../northbridge/intel/i945/acpi/i945_peg.asl" // Integrated graphics 0:2.0 -Include ("../../../northbridge/intel/i945/acpi/i945_igd.asl") +#include "../../../northbridge/intel/i945/acpi/i945_igd.asl" Scope (\) { // backlight control, display switching, lid - Include ("acpi/video.asl") + #include "acpi/video.asl" } diff --git a/src/northbridge/intel/i945/acpi/i945_hostbridge.asl b/src/northbridge/intel/i945/acpi/i945_hostbridge.asl index 9e9c43611b..554adc0367 100644 --- a/src/northbridge/intel/i945/acpi/i945_hostbridge.asl +++ b/src/northbridge/intel/i945/acpi/i945_hostbridge.asl @@ -23,6 +23,9 @@ Name(_HID,EISAID("PNP0A08")) // PCIe Name(_CID,EISAID("PNP0A03")) // PCI +Name(_ADR, 0) +Name(_BBN, 0) + Device (MCHC) { Name(_ADR, 0x00000000) // 0:0.0 @@ -232,6 +235,6 @@ Method (_CRS, 0, Serialized) } /* IRQ assignment is mainboard specific. Get it from mainboard ACPI code */ -Include ("acpi/i945_pci_irqs.asl") +#include "acpi/i945_pci_irqs.asl" diff --git a/src/northbridge/intel/i945/early_init.c b/src/northbridge/intel/i945/early_init.c index 5894bff5b1..e8dea60217 100644 --- a/src/northbridge/intel/i945/early_init.c +++ b/src/northbridge/intel/i945/early_init.c @@ -518,6 +518,33 @@ static void i945_setup_pci_express_x16(void) reg32 &= ~(1 << 8); pcie_write_config32(PCI_DEV(0, 0x01, 0), 0x208, reg32); + /* We have no success with querying the usual PCIe registers + * for link setup success on the i945. Hence we assign a temporary + * PCI bus 0x0a and check whether we find a device on 0:a.0 + */ + + /* First we reset the secondary bus */ + reg16 = pci_read_config16(PCI_DEV(0, 0x01, 0), 0x3e); + reg16 |= (1 << 6); + pci_write_config16(PCI_DEV(0, 0x01, 0), 0x3e, reg16); + /* Read back and clear reset bit. */ + reg16 = pci_read_config16(PCI_DEV(0, 0x01, 0), 0x3e); + reg16 &= ~(1 << 6); + pci_write_config16(PCI_DEV(0, 0x01, 0), 0x3e, reg16); + + reg16 = pci_read_config16(PCI_DEV(0, 0x01, 0), 0xba); + printk_debug("SLOTSTS: %04x\n", reg16); + if (!(reg16 & 0x48)) { + goto disable_pciexpress_x16_link; + } + reg16 |= (1 << 4) | (1 << 0); + pci_write_config16(PCI_DEV(0, 0x01, 0), 0xba, reg16); + + pci_write_config8(PCI_DEV(0, 0x01, 0), 0x19, 0x00); + pci_write_config8(PCI_DEV(0, 0x01, 0), 0x1a, 0x00); + pci_write_config8(PCI_DEV(0, 0x01, 0), 0x19, 0x0a); + pci_write_config8(PCI_DEV(0, 0x01, 0), 0x1a, 0x0a); + reg32 = pcie_read_config32(PCI_DEV(0, 0x01, 0), 0x224); reg32 &= ~(1 << 8); pcie_write_config32(PCI_DEV(0, 0x01, 0), 0x224, reg32); @@ -542,11 +569,16 @@ static void i945_setup_pci_express_x16(void) pcie_write_config32(PCI_DEV(0, 0x01, 0), 0xb4, reg32); /* Wait for training to succeed */ - printk_debug("Wait for PCIe x16 link training ..."); - timeout = 0x7fff; + printk_debug("PCIe link training ..."); + timeout = 0x7ffff; while ((((pcie_read_config32(PCI_DEV(0, 0x01, 0), 0x214) >> 16) & 4) != 3) && --timeout) ; - if (!timeout) { - printk_debug("timeout!\n"); + + reg32 = pci_read_config32(PCI_DEV(0x0a, 0x0, 0), 0); + if (reg32 != 0x00000000 && reg32 != 0xffffffff) { + printk_debug(" Detected PCIe device %04x:%04x\n", + reg32 & 0xffff, reg32 >> 16); + } else { + printk_debug(" timeout!\n"); printk_debug("Restrain PCIe port to x1\n"); @@ -562,18 +594,19 @@ static void i945_setup_pci_express_x16(void) reg16 &= ~(1 << 6); pcie_write_config16(PCI_DEV(0, 0x01, 0), 0x3e, reg16); - printk_debug("Wait for PCIe x1 link training ..."); - timeout = 0x7fff; + printk_debug("PCIe link training ..."); + timeout = 0x7ffff; while ((((pcie_read_config32(PCI_DEV(0, 0x01, 0), 0x214) >> 16) & 4) != 3) && --timeout) ; - if (!timeout) { - printk_debug("timeout!\n"); + + reg32 = pci_read_config32(PCI_DEV(0xa, 0x00, 0), 0); + if (reg32 != 0x00000000 && reg32 != 0xffffffff) { + printk_debug(" Detected PCIe x1 device %04x:%04x\n", + reg32 & 0xffff, reg32 >> 16); + } else { + printk_debug(" timeout!\n"); printk_debug("Disabling PCIe x16 port completely.\n"); goto disable_pciexpress_x16_link; - } else { - printk_debug("ok\n"); } - } else { - printk_debug("ok\n"); } reg16 = pcie_read_config16(PCI_DEV(0, 0x01, 0), 0xb2); @@ -592,6 +625,24 @@ static void i945_setup_pci_express_x16(void) // TODO } + reg32 = (pci_read_config32(PCI_DEV(0xa, 0, 0), 0x8) >> 8); + printk_debug("PCIe device class: %06x\n", reg32); + if (reg32 == 0x030000) { + printk_debug("PCIe device is VGA. Disabling IGD.\n"); + reg16 = (1 << 1); + pci_write_config16(PCI_DEV(0, 0x0, 0), 0x52, reg16); + + /* DEVEN */ + reg32 = pci_read_config32(PCI_DEV(0, 0x0, 0), 0x54); + reg32 &= ~((1 << 3) | (1 << 4)); + pci_write_config32(PCI_DEV(0, 0x0, 0), 0x54, reg32); + + /* Set VGA enable bit in PCIe bridge */ + reg16 = pci_read_config16(PCI_DEV(0, 0x1, 0), 0x3e); + reg16 |= (1 << 3); + pci_write_config16(PCI_DEV(0, 0x1, 0), 0x3e, reg16); + } + /* Enable GPEs */ reg32 = pcie_read_config32(PCI_DEV(0, 0x01, 0), 0xec); reg32 |= (1 << 2) | (1 << 1) | (1 << 0); /* PMEGPE, HPGPE, GENGPE */ diff --git a/src/northbridge/intel/i945/i945.h b/src/northbridge/intel/i945/i945.h index a1f7185bde..a23e3a8f82 100644 --- a/src/northbridge/intel/i945/i945.h +++ b/src/northbridge/intel/i945/i945.h @@ -20,8 +20,18 @@ #ifndef __NORTHBRIDGE_INTEL_I945_I945_H__ #define __NORTHBRIDGE_INTEL_I945_I945_H__ 1 +/* Northbridge BARs */ +#define DEFAULT_PCIEXBAR CONFIG_MMCONF_BASE_ADDRESS /* 4 KB per PCIe device */ +#define DEFAULT_X60BAR 0xfed13000 +#define DEFAULT_MCHBAR 0xfed14000 /* 16 KB */ +#define DEFAULT_DMIBAR 0xfed18000 /* 4 KB */ +#define DEFAULT_EPBAR 0xfed19000 /* 4 KB */ + #include "../../../southbridge/intel/i82801gx/i82801gx.h" +/* Everything below this line is ignored in the DSDT */ +#ifndef __ACPI__ + /* Device 0:0.0 PCI configuration space (Host Bridge) */ #define EPBAR 0x40 @@ -30,13 +40,6 @@ #define DMIBAR 0x4c #define X60BAR 0x60 -/* Northbridge BARs */ -#define DEFAULT_PCIEXBAR 0xf0000000 /* 4 KB per PCIe device */ -#define DEFAULT_X60BAR 0xfed13000 -#define DEFAULT_MCHBAR 0xfed14000 /* 16 KB */ -#define DEFAULT_DMIBAR 0xfed18000 /* 4 KB */ -#define DEFAULT_EPBAR 0xfed19000 /* 4 KB */ - #define GGC 0x52 /* GMCH Graphics Control */ #define DEVEN 0x54 /* Device Enable */ @@ -329,3 +332,4 @@ #define DMIDRCCFG 0xeb4 /* 32bit */ #endif +#endif diff --git a/src/northbridge/intel/i945/northbridge.c b/src/northbridge/intel/i945/northbridge.c index b2851cd336..4ccffc6b55 100644 --- a/src/northbridge/intel/i945/northbridge.c +++ b/src/northbridge/intel/i945/northbridge.c @@ -44,7 +44,7 @@ int get_pcie_bar(u32 *base, u32 *len) if (!dev) return 0; - pciexbar_reg = pci_read_config32(dev, 0x48); + pciexbar_reg = pci_read_config32(dev, PCIEXBAR); if (!(pciexbar_reg & (1 << 0))) return 0; @@ -67,9 +67,6 @@ int get_pcie_bar(u32 *base, u32 *len) return 0; } -/* in arch/i386/boot/tables.c */ -extern uint64_t high_tables_base, high_tables_size; - /* IDG memory */ uint64_t uma_memory_base=0, uma_memory_size=0; @@ -127,7 +124,7 @@ static uint32_t find_pci_tolm(struct bus *bus) } #if CONFIG_WRITE_HIGH_TABLES==1 -#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB +#define HIGH_TABLES_SIZE 1024 // maximum size of high tables in KB extern uint64_t high_tables_base, high_tables_size; #endif @@ -284,6 +281,28 @@ static void intel_set_subsystem(device_t dev, unsigned vendor, unsigned device) } } +#if CONFIG_HAVE_ACPI_RESUME +extern u8 acpi_slp_type; + +static void northbridge_init(struct device *dev) +{ + switch (pci_read_config32(dev, SKPAD)) { + case 0xcafebabe: + printk_debug("Normal boot.\n"); + acpi_slp_type=0; + break; + case 0xcafed00d: + printk_debug("S3 Resume.\n"); + acpi_slp_type=3; + break; + default: + printk_debug("Unknown boot method, assuming normal.\n"); + acpi_slp_type=0; + break; + } +} +#endif + static struct pci_operations intel_pci_ops = { .set_subsystem = intel_set_subsystem, }; @@ -292,7 +311,9 @@ static struct device_operations mc_ops = { .read_resources = mc_read_resources, .set_resources = mc_set_resources, .enable_resources = pci_dev_enable_resources, - .init = 0, +#if CONFIG_HAVE_ACPI_RESUME + .init = northbridge_init, +#endif .scan_bus = 0, .ops_pci = &intel_pci_ops, }; diff --git a/src/northbridge/intel/i945/raminit.c b/src/northbridge/intel/i945/raminit.c index 3084072389..53a7455ea9 100644 --- a/src/northbridge/intel/i945/raminit.c +++ b/src/northbridge/intel/i945/raminit.c @@ -2481,6 +2481,9 @@ static void sdram_program_receive_enable(struct sys_info *sysinfo) { MCHBAR32(REPC) |= (1 << 0); + /* enable upper CMOS */ + RCBA32(0x3400) = (1 << 2); + /* Program Receive Enable Timings */ if (sysinfo->boot_path == BOOT_PATH_RESUME) { sdram_recover_receive_enable(); @@ -2904,9 +2907,7 @@ void sdram_initialize(int boot_path) sdram_thermal_management(); /* Normal Operations */ - if (boot_path == BOOT_PATH_NORMAL) { - sdram_init_complete(); - } + sdram_init_complete(); /* Program Receive Enable Timings */ sdram_program_receive_enable(&sysinfo); @@ -2924,3 +2925,11 @@ void sdram_initialize(int boot_path) sdram_setup_processor_side(); } +unsigned long get_top_of_ram(void) +{ + /* This will not work if TSEG is in place! */ + u32 tom = pci_read_config32(PCI_DEV(0,2,0), 0x5c); + + return (unsigned long) tom; +} + diff --git a/src/southbridge/intel/i82801gx/acpi/globalnvs.asl b/src/southbridge/intel/i82801gx/acpi/globalnvs.asl index 5ac1c83cd6..0384376417 100644 --- a/src/southbridge/intel/i82801gx/acpi/globalnvs.asl +++ b/src/southbridge/intel/i82801gx/acpi/globalnvs.asl @@ -81,7 +81,16 @@ Field (GNVS, ByteAcc, NoLock, Preserve) PPCM, 8, // 0x2c - Max. PPC state /* Super I/O & CMOS config */ Offset (0x32), - NATP, 8, // 0x32 - ... + NATP, 8, // 0x32 - + CMAP, 8, // 0x33 - + CMBP, 8, // 0x34 - + LPTP, 8, // 0x35 - LPT Port + FDCP, 8, // 0x36 - Floppy Disk Controller + RFDV, 8, // 0x37 - + HOTK, 8, // 0x38 - + RTCF, 8, // 0x39 - + UTIL, 8, // 0x3a - + ACIN, 8, // 0x3b - /* Integrated Graphics Device */ Offset (0x3c), IGDS, 8, // 0x3c - IGD state (primary = 1) @@ -158,4 +167,5 @@ Field (GNVS, ByteAcc, NoLock, Preserve) /* Mainboard Specific (TODO move elsewhere) */ Offset (0xf0), DOCK, 8, // 0xf0 - Docking Status + BTEN, 8, // 0xf1 - Bluetooth Enable } diff --git a/src/southbridge/intel/i82801gx/acpi/ich7.asl b/src/southbridge/intel/i82801gx/acpi/ich7.asl index 3f845c483b..a37208c021 100644 --- a/src/southbridge/intel/i82801gx/acpi/ich7.asl +++ b/src/southbridge/intel/i82801gx/acpi/ich7.asl @@ -19,8 +19,7 @@ * MA 02110-1301 USA */ -/* Intel i82801G support - */ +/* Intel 82801Gx support */ Scope(\) { @@ -34,10 +33,7 @@ Scope(\) } // ICH7 Power Management Registers, located at PMBASE (0x1f.0 0x40.l) - // this doesn't work as ACPI initializes regions and packages first, devices second. - // use dynamic operation region? if so, how? XXX - //OperationRegion(PMIO, SystemIO, And(\_SB_.PCI0.LPCB.PMBS, 0xfffc), 0x80) - OperationRegion(PMIO, SystemIO, 0x500, 0x80) + OperationRegion(PMIO, SystemIO, DEFAULT_PMBASE, 0x80) Field(PMIO, ByteAcc, NoLock, Preserve) { Offset(0x42), // General Purpose Control @@ -49,7 +45,7 @@ Scope(\) } // ICH7 GPIO IO mapped registers (0x1f.0 reg 0x48.l) - OperationRegion(GPIO, SystemIO, 0x1180, 0x3c) + OperationRegion(GPIO, SystemIO, DEFAULT_GPIOBASE, 0x3c) Field(GPIO, ByteAcc, NoLock, Preserve) { Offset(0x00), // GPIO Use Select @@ -63,12 +59,32 @@ Scope(\) GIO2, 8, GIO3, 8, Offset(0x0c), // GPIO Level - GL00, 8, - GL01, 8, - , 3, - GP27, 1, // SATA_PWR_EN #0 - GP28, 1, // SATA_PWR_EN #1 - , 3, + GL00, 6, + GP07, 1, // GDET + GP08, 1, + GP09, 1, + GP10, 1, // HPMU + GP11, 1, // GPSE + GP12, 1, + GP13, 1, // WLED + GP14, 1, // BLED + GP15, 1, // GLED + GP16, 1, // GDIS + GP17, 1, + GP18, 1, + GP19, 1, // SPCI + GP20, 1, // TSDT + GP21, 1, // SCPU + GP22, 1, + GP23, 1, + GP24, 1, // LANP + GP25, 1, // DKLR + GP26, 1, // WLAN + GP27, 1, // SATA_PWR_EN #0 / SPOF + GP28, 1, // SATA_PWR_EN #1 / SPMU + GP29, 1, + GP30, 1, + GP31, 1, Offset(0x18), // GPIO Blink GB00, 8, GB01, 8, @@ -90,10 +106,14 @@ Scope(\) GIO6, 8, GIO7, 8, Offset(0x38), // GPIO Level 2 - , 5, - GP37, 1, // PATA_PWR_EN - GP38, 1, // Battery / Power (?) - GP39, 1, // ?? + GP32, 1, + GP33, 1, // CREN + GP34, 1, // CRRS + GP35, 1, + GP36, 1, // STAD + GP37, 1, // PATA_PWR_EN / HDDE + GP38, 1, // Battery / Power (?) / MB00 + GP39, 1, // ?? / MB01 GL05, 8, GL06, 8, GL07, 8 @@ -101,7 +121,7 @@ Scope(\) // ICH7 Root Complex Register Block. Memory Mapped through RCBA) - OperationRegion(RCRB, SystemMemory, 0xfed1c000, 0x4000) + OperationRegion(RCRB, SystemMemory, DEFAULT_RCBA, 0x4000) Field(RCRB, DWordAcc, Lock, Preserve) { Offset(0x0000), // Backbone @@ -139,30 +159,30 @@ Scope(\) } // 0:1b.0 High Definition Audio (Azalia) -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_audio.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_audio.asl" // PCI Express Ports -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_pcie.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_pcie.asl" // USB -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_usb.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_usb.asl" // PCI Bridge -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_pci.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_pci.asl" // AC97 Audio and Modem -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_ac97.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_ac97.asl" // LPC Bridge -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_lpc.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_lpc.asl" // PATA -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_pata.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_pata.asl" // SATA -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_sata.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_sata.asl" // SMBus -Include ("../../../southbridge/intel/i82801gx/acpi/ich7_smbus.asl") +#include "../../../southbridge/intel/i82801gx/acpi/ich7_smbus.asl" diff --git a/src/southbridge/intel/i82801gx/acpi/ich7_lpc.asl b/src/southbridge/intel/i82801gx/acpi/ich7_lpc.asl index fdf05b2e2f..a18673c679 100644 --- a/src/southbridge/intel/i82801gx/acpi/ich7_lpc.asl +++ b/src/southbridge/intel/i82801gx/acpi/ich7_lpc.asl @@ -51,9 +51,9 @@ Device (LPCB) RCBA, 18, } - Include ("../../../southbridge/intel/i82801gx/acpi/ich7_irqlinks.asl") + #include "../../../southbridge/intel/i82801gx/acpi/ich7_irqlinks.asl" - Include ("acpi/ec.asl") + #include "acpi/ec.asl" Device (DMAC) // DMA Controller { @@ -174,11 +174,9 @@ Device (LPCB) IO (Decode16, 0x80, 0x80, 0x1, 0x01) // Port 80 Post IO (Decode16, 0x92, 0x92, 0x1, 0x01) // CPU Reserved IO (Decode16, 0xb2, 0xb2, 0x1, 0x02) // SWSMI - // IO (Decode16, 0x680, 0x680, 0x1, 0x70) // IO ??? IO (Decode16, 0x800, 0x800, 0x1, 0x10) // ACPI I/O trap - IO (Decode16, 0x0500, 0x0500, 0x1, 0x80) // ICH7-M ACPI - IO (Decode16, 0x0480, 0x0480, 0x1, 0x40) // ICH7-M GPIO - // IO (Decode16, 0x1640, 0x1640, 0x1, 0x10) // IO ??? + IO (Decode16, DEFAULT_PMBASE, DEFAULT_PMBASE, 0x1, 0x80) // ICH7-M ACPI + IO (Decode16, DEFAULT_GPIOBASE, DEFAULT_GPIOBASE, 0x1, 0x40) // ICH7-M GPIO }) } @@ -188,7 +186,8 @@ Device (LPCB) Name (_CRS, ResourceTemplate() { IO (Decode16, 0x70, 0x70, 1, 8) - IRQNoFlags() { 8 } +// Disable as Windows doesn't like it, and systems don't seem to use it. +// IRQNoFlags() { 8 } }) } @@ -203,7 +202,31 @@ Device (LPCB) }) } - Include ("acpi/superio.asl") + #include "acpi/superio.asl" + +#ifdef ENABLE_TPM + Device (TPM) // Trusted Platform Module + { + Name(_HID, EISAID("IFX0102")) + Name(_CID, 0x310cd041) + Name(_UID, 1) + + Method(_STA, 0) + { + If (TPMP) { + Return (0xf) + } + Return (0x0) + } + + Name(_CRS, ResourceTemplate() { + IO (Decode16, 0x2e, 0x2e, 0x01, 0x02) + IO (Decode16, 0x6f0, 0x6f0, 0x01, 0x10) + Memory32Fixed (ReadWrite, 0xfed40000, 0x5000) + IRQ (Edge, Activehigh, Exclusive) { 6 } + }) + } +#endif Device (PS2K) // Keyboard { @@ -237,6 +260,7 @@ Device (LPCB) } } +#ifdef ENABLE_FDC Device (FDC0) // Floppy controller { Name (_HID, EisaId ("PNP0700")) @@ -262,4 +286,5 @@ Device (LPCB) }) } +#endif } diff --git a/src/southbridge/intel/i82801gx/acpi/ich7_pci.asl b/src/southbridge/intel/i82801gx/acpi/ich7_pci.asl index 9bcf58e413..d253d51a78 100644 --- a/src/southbridge/intel/i82801gx/acpi/ich7_pci.asl +++ b/src/southbridge/intel/i82801gx/acpi/ich7_pci.asl @@ -70,7 +70,7 @@ Device (PCIB) Method (_PRT) { - Include ("acpi/ich7_pci_irqs.asl") + #include "acpi/ich7_pci_irqs.asl" } } diff --git a/src/southbridge/intel/i82801gx/acpi/ich7_pcie.asl b/src/southbridge/intel/i82801gx/acpi/ich7_pcie.asl index 0822e8ee02..a76c7fbe4d 100644 --- a/src/southbridge/intel/i82801gx/acpi/ich7_pcie.asl +++ b/src/southbridge/intel/i82801gx/acpi/ich7_pcie.asl @@ -26,7 +26,7 @@ Device (RP01) { NAME(_ADR, 0x001c0000) // FIXME: Have a macro for PCI Devices -> ACPI notation? - //Include ("pcie_port.asl") + //#include "pcie_port.asl" Method(_PRT) { If (PICM) { @@ -52,7 +52,7 @@ Device (RP01) Device (RP02) { NAME(_ADR, 0x001c0001) // FIXME: Have a macro for PCI Devices -> ACPI notation? - //Include ("pcie_port.asl") + //#include "pcie_port.asl" Method(_PRT) { If (PICM) { @@ -79,7 +79,7 @@ Device (RP02) Device (RP03) { NAME(_ADR, 0x001c0002) // FIXME: Have a macro for PCI Devices -> ACPI notation? - //Include ("pcie_port.asl") + //#include "pcie_port.asl" Method(_PRT) { If (PICM) { @@ -106,7 +106,7 @@ Device (RP03) Device (RP04) { NAME(_ADR, 0x001c0003) // FIXME: Have a macro for PCI Devices -> ACPI notation? - //Include ("pcie_port.asl") + //#include "pcie_port.asl" Method(_PRT) { If (PICM) { @@ -133,7 +133,7 @@ Device (RP04) Device (RP05) { NAME(_ADR, 0x001c0004) // FIXME: Have a macro for PCI Devices -> ACPI notation? - //Include ("pcie_port.asl") + //#include "pcie_port.asl" Method(_PRT) { If (PICM) { @@ -160,7 +160,7 @@ Device (RP05) Device (RP06) { NAME(_ADR, 0x001c0005) // FIXME: Have a macro for PCI Devices -> ACPI notation? - //Include ("pcie_port.asl") + //#include "pcie_port.asl" Method(_PRT) { If (PICM) { diff --git a/src/southbridge/intel/i82801gx/acpi/ich7_smbus.asl b/src/southbridge/intel/i82801gx/acpi/ich7_smbus.asl index b7d807ee44..b6d2d6a2ab 100644 --- a/src/southbridge/intel/i82801gx/acpi/ich7_smbus.asl +++ b/src/southbridge/intel/i82801gx/acpi/ich7_smbus.asl @@ -33,7 +33,6 @@ Device (SBUS) I2CE, 1 } - /* OperationRegion (SMBI, SystemIO, 0x400, 0x20) Field (SMBI, ByteAcc, NoLock, Preserve) { @@ -59,6 +58,7 @@ Device (SBUS) NDLH, 8, // Notify Data High Byte } +#ifdef ENABLE_SMBUS_METHODS // Kill all SMBus communication Method (KILL, 0, Serialized) { @@ -237,10 +237,6 @@ Device (SBUS) Return (0xffff) } - */ - - // Todo: Does anyone ever use these? - // Missing: Read / Write Word - // Missing: Read / Write Block +#endif } diff --git a/src/southbridge/intel/i82801gx/acpi/sleepstates.asl b/src/southbridge/intel/i82801gx/acpi/sleepstates.asl index 61595854b2..863eee72dd 100644 --- a/src/southbridge/intel/i82801gx/acpi/sleepstates.asl +++ b/src/southbridge/intel/i82801gx/acpi/sleepstates.asl @@ -19,9 +19,9 @@ * MA 02110-1301 USA */ -Name(\_S0, Package(4){0x0,0x0,0,0}) -Name(\_S1, Package(4){0x1,0x0,0,0}) -Name(\_S3, Package(4){0x5,0x0,0,0}) -Name(\_S4, Package(4){0x6,0x0,0,0}) -Name(\_S5, Package(4){0x7,0x0,0,0}) +Name(\_S0, Package(){0x0,0x0,0,0}) +Name(\_S1, Package(){0x1,0x0,0,0}) +Name(\_S3, Package(){0x5,0x0,0,0}) +Name(\_S4, Package(){0x6,0x0,0,0}) +Name(\_S5, Package(){0x7,0x0,0,0}) diff --git a/src/southbridge/intel/i82801gx/chip.h b/src/southbridge/intel/i82801gx/chip.h index 7fca7ca9f3..7b16e8b3dc 100644 --- a/src/southbridge/intel/i82801gx/chip.h +++ b/src/southbridge/intel/i82801gx/chip.h @@ -61,14 +61,14 @@ struct southbridge_intel_i82801gx_config { uint8_t gpi14_routing; uint8_t gpi15_routing; + uint32_t gpe0_en; + uint16_t alt_gp_smi_en; + /* IDE configuration */ uint32_t ide_legacy_combined; uint32_t ide_enable_primary; uint32_t ide_enable_secondary; uint32_t sata_ahci; - - /* Azalia Configuration */ - uint32_t hda_viddid; }; extern struct chip_operations southbridge_intel_i82801gx_ops; diff --git a/src/southbridge/intel/i82801gx/i82801gx.h b/src/southbridge/intel/i82801gx/i82801gx.h index 98c62ce091..9b54fc6008 100644 --- a/src/southbridge/intel/i82801gx/i82801gx.h +++ b/src/southbridge/intel/i82801gx/i82801gx.h @@ -20,6 +20,23 @@ #ifndef SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H #define SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H +/* + * It does not matter where we put the SMBus I/O base, as long as we + * keep it consistent and don't interfere with other devices. Stage2 + * will relocate this anyways. + * Our solution is to have SMB initialization move the I/O to SMBUS_IO_BASE + * again. But handling static BARs is a generic problem that should be + * solved in the device allocator. + */ +#define SMBUS_IO_BASE 0x0400 +/* TODO Make sure these don't get changed by stage2 */ +#define DEFAULT_GPIOBASE 0x0480 +#define DEFAULT_PMBASE 0x0500 +#define HPET_ADDR 0xfed00000 +#define DEFAULT_RCBA 0xfed1c000 + +#ifndef __ACPI__ +#define DEBUG_PERIODIC_SMIS 0 /* __ROMCC__ is set by auto.c to make sure * none of the stage2 data structures are included. @@ -91,11 +108,18 @@ extern void i82801gx_enable(device_t dev); #define IDE_SDMA_TIM 0x4a #define IDE_CONFIG 0x54 /* IDE I/O Configuration Register */ -#define SIG_MODE_NORMAL (0 << 16) -#define SIG_MODE_TRISTATE (1 << 16) -#define SIG_MODE_DRIVELOW (2 << 16) +#define SIG_MODE_SEC_NORMAL (0 << 18) +#define SIG_MODE_SEC_TRISTATE (1 << 18) +#define SIG_MODE_SEC_DRIVELOW (2 << 18) +#define SIG_MODE_PRI_NORMAL (0 << 16) +#define SIG_MODE_PRI_TRISTATE (1 << 16) +#define SIG_MODE_PRI_DRIVELOW (2 << 16) +#define FAST_SCB1 (1 << 15) +#define FAST_SCB0 (1 << 14) #define FAST_PCB1 (1 << 13) #define FAST_PCB0 (1 << 12) +#define SCB1 (1 << 3) +#define SCB0 (1 << 2) #define PCB1 (1 << 1) #define PCB0 (1 << 0) @@ -108,16 +132,7 @@ extern void i82801gx_enable(device_t dev); #define SMB_SMI_EN (1 << 1) #define HST_EN (1 << 0) -/* SMBus I/O bits. - * It does not matter where we put the SMBus I/O base, as long as we - * keep it consistent and don't interfere with other devices. Stage2 - * will relocate this anyways. - * Our solution is to have SMB initialization move the I/O to SMBUS_IO_BASE - * again. But handling static BARs is a generic problem that should be - * solved in the device allocator. - */ -#define SMBUS_IO_BASE 0x0400 - +/* SMBus I/O bits. */ #define SMBHSTSTAT 0x0 #define SMBHSTCTL 0x2 #define SMBHSTCMD 0x3 @@ -132,21 +147,15 @@ extern void i82801gx_enable(device_t dev); #define SMBUS_TIMEOUT (10 * 1000 * 100) -/* HPET, if present */ -#define HPET_ADDR 0xfed0000 /* Southbridge IO BARs */ -/* TODO Make sure these don't get changed by stage2 */ #define GPIOBASE 0x48 -#define DEFAULT_GPIOBASE 0x480 #define PMBASE 0x40 -#define DEFAULT_PMBASE 0x500 /* Root Complex Register Block */ #define RCBA 0xf0 -#define DEFAULT_RCBA 0xfed1c000 #define RCBA8(x) *((volatile u8 *)(DEFAULT_RCBA + x)) #define RCBA16(x) *((volatile u16 *)(DEFAULT_RCBA + x)) @@ -255,4 +264,56 @@ extern void i82801gx_enable(device_t dev); #define FD_SATA (1 << 2) #define FD_PATA (1 << 1) +/* ICH7 GPIOBASE */ +#define GPIO_USE_SEL 0x00 +#define GP_IO_SEL 0x04 +#define GP_LVL 0x0c +#define GPO_BLINK 0x18 +#define GPI_INV 0x2c +#define GPIO_USE_SEL2 0x30 +#define GP_IO_SEL2 0x34 +#define GP_LVL2 0x38 + +/* ICH7 PMBASE */ +#define PM1_STS 0x00 +#define PM1_EN 0x02 +#define PM1_CNT 0x04 +#define SLP_EN (1 << 13) +#define SLP_TYP (7 << 10) +#define GBL_RLS (1 << 2) +#define BM_RLD (1 << 1) +#define SCI_EN (1 << 0) +#define PM1_TMR 0x08 +#define PROC_CNT 0x10 +#define LV2 0x14 +#define LV3 0x15 +#define LV4 0x16 +#define PM2_CNT 0x20 // mobile only +#define GPE0_STS 0x28 +#define GPE0_EN 0x2c +#define PME_B0_EN (1 << 13) +#define SMI_EN 0x30 +#define EL_SMI_EN (1 << 25) // Intel Quick Resume Technology +#define INTEL_USB2_EN (1 << 18) // Intel-Specific USB2 SMI logic +#define LEGACY_USB2_EN (1 << 17) // Legacy USB2 SMI logic +#define PERIODIC_EN (1 << 14) // SMI on PERIODIC_STS in SMI_STS +#define TCO_EN (1 << 13) // Enable TCO Logic (BIOSWE et al) +#define MCSMI_EN (1 << 11) // Trap microcontroller range access +#define BIOS_RLS (1 << 7) // asserts SCI on bit set +#define SWSMI_TMR_EN (1 << 6) // start software smi timer on bit set +#define APMC_EN (1 << 5) // Writes to APM_CNT cause SMI# +#define SLP_SMI_EN (1 << 4) // Write to SLP_EN in PM1_CNT asserts SMI# +#define LEGACY_USB_EN (1 << 3) // Legacy USB circuit SMI logic +#define BIOS_EN (1 << 2) // Assert SMI# on setting GBL_RLS bit +#define EOS (1 << 1) // End of SMI (deassert SMI#) +#define GBL_SMI_EN (1 << 0) // SMI# generation at all? +#define SMI_STS 0x34 +#define ALT_GP_SMI_EN 0x38 +#define ALT_GP_SMI_STS 0x3a +#define GPE_CNTL 0x42 +#define DEVACT_STS 0x44 +#define SS_CNT 0x50 +#define C3_RES 0x54 + +#endif /* __ACPI__ */ #endif /* SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H */ diff --git a/src/southbridge/intel/i82801gx/i82801gx_azalia.c b/src/southbridge/intel/i82801gx/i82801gx_azalia.c index 1435866100..fd71813f5a 100644 --- a/src/southbridge/intel/i82801gx/i82801gx_azalia.c +++ b/src/southbridge/intel/i82801gx/i82801gx_azalia.c @@ -90,93 +90,25 @@ no_codec: return 0; } -static u32 cim_verb_data[] = { - 0x00172000, - 0x00172100, - 0x001722EC, - 0x00172310, - - /* Pin Complex (NID 0x12) */ - 0x01271CF0, - 0x01271D11, - 0x01271E11, - 0x01271F41, - /* Pin Complex (NID 0x14) */ - 0x01471C10, - 0x01471D01, - 0x01471E13, - 0x01471F99, - /* Pin Complex (NID 0x15) */ - 0x01571C20, - 0x01571D40, - 0x01571E21, - 0x01571F01, - /* Pin Complex (NID 0x16) */ - 0x01671CF0, - 0x01671D11, - 0x01671E11, - 0x01671F41, - /* Pin Complex (NID 0x18) */ - 0x01871C30, - 0x01871D98, - 0x01871EA1, - 0x01871F01, - /* Pin Complex (NID 0x19) */ - 0x01971C31, - 0x01971D09, - 0x01971EA3, - 0x01971F99, - /* Pin Complex (NID 0x1A) */ - 0x01A71C3F, - 0x01A71D98, - 0x01A71EA1, - 0x01A71F02, - /* Pin Complex (NID 0x1B) */ - 0x01B71C1F, - 0x01B71D40, - 0x01B71E21, - 0x01B71F02, - /* Pin Complex (NID 0x1C) */ - 0x01C71CF0, - 0x01C71D11, - 0x01C71E11, - 0x01C71F41, - /* Pin Complex (NID 0x1D) */ - 0x01D71CF0, - 0x01D71D11, - 0x01D71E11, - 0x01D71F41, - /* Pin Complex (NID 0x1E) */ - 0x01E71CF0, - 0x01E71D11, - 0x01E71E11, - 0x01E71F41, - /* Pin Complex (NID 0x1F) */ - 0x01F71CF0, - 0x01F71D11, - 0x01F71E11, - 0x01F71F41, -}; +u32 * cim_verb_data = NULL; +u32 cim_verb_data_size = 0; -static unsigned find_verb(struct device *dev, u32 viddid, u32 ** verb) +static u32 find_verb(struct device *dev, u32 viddid, u32 ** verb) { - config_t *config = dev->chip_info; - - if (config == NULL) { - printk_err("\ni82801gx_azalia: Not mentioned in mainboard's Config.lb!\n"); - return 0; + int idx=0; + + while (idx < (cim_verb_data_size / sizeof(u32))) { + u32 verb_size = 4 * cim_verb_data[idx+2]; // in u32 + if (cim_verb_data[idx] != viddid) { + idx += verb_size + 3; // skip verb + header + continue; + } + *verb = &cim_verb_data[idx+3]; + return verb_size; } - printk_debug("Azalia: dev=%s\n", dev_path(dev)); - printk_debug("Azalia: Default viddid=%x\n", (u32)config->hda_viddid); - printk_debug("Azalia: Reading viddid=%x\n", viddid); - - if (viddid != config->hda_viddid) - return 0; - - *verb = (u32 *) cim_verb_data; - - return sizeof(cim_verb_data) / sizeof(u32); + /* Not all codecs need to load another verb */ + return 0; } /** @@ -209,19 +141,26 @@ static int wait_for_ready(u8 *base) static int wait_for_valid(u8 *base) { + u32 reg32; + + /* Send the verb to the codec */ + reg32 = readl(base + 0x68); + reg32 |= (1 << 0) | (1 << 1); + writel(reg32, base + 0x68); + /* Use a 50 usec timeout - the Linux kernel uses the * same duration */ int timeout = 50; while(timeout--) { - u32 reg32 = readl(base + HDA_ICII_REG); + reg32 = readl(base + HDA_ICII_REG); if ((reg32 & (HDA_ICII_VALID | HDA_ICII_BUSY)) == HDA_ICII_VALID) return 0; udelay(1); } - return 1; + return -1; } static void codec_init(struct device *dev, u8 * base, int addr) @@ -231,6 +170,8 @@ static void codec_init(struct device *dev, u8 * base, int addr) u32 verb_size; int i; + printk_debug("Azalia: Initializing codec #%d\n", addr); + /* 1 */ if (wait_for_ready(base) == -1) return; @@ -251,8 +192,8 @@ static void codec_init(struct device *dev, u8 * base, int addr) printk_debug("Azalia: No verb!\n"); return; } - printk_debug("Azalia: verb_size: %d\n", verb_size); + /* 3 */ for (i = 0; i < verb_size; i++) { if (wait_for_ready(base) == -1) diff --git a/src/southbridge/intel/i82801gx/i82801gx_ide.c b/src/southbridge/intel/i82801gx/i82801gx_ide.c index c29e678a69..28a1c055ea 100644 --- a/src/southbridge/intel/i82801gx/i82801gx_ide.c +++ b/src/southbridge/intel/i82801gx/i82801gx_ide.c @@ -38,7 +38,7 @@ static void ide_init(struct device *dev) printk_debug("i82801gx_ide: initializing... "); if (config == NULL) { printk_err("\ni82801gx_ide: Not mentioned in mainboard's Config.lb!\n"); - // Trying to set somewhat save defaults instead of bailing out. + // Trying to set somewhat safe defaults instead of bailing out. enable_primary = enable_secondary = 1; } else { enable_primary = config->ide_enable_primary; @@ -80,10 +80,12 @@ static void ide_init(struct device *dev) pci_write_config16(dev, IDE_TIM_SEC, ideTimingConfig); /* Set IDE I/O Configuration */ + reg32 = 0; + /* FIXME: only set FAST_* for ata/100, only ?CBx for ata/66 */ + if (enable_primary) + reg32 |= SIG_MODE_PRI_NORMAL | FAST_PCB0 | PCB0 | FAST_PCB1 | PCB1; if (enable_secondary) - reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; - else - reg32 = SIG_MODE_NORMAL | FAST_PCB1 | PCB1; + reg32 |= SIG_MODE_SEC_NORMAL | FAST_SCB0 | SCB0 | FAST_SCB1 | SCB1; pci_write_config32(dev, IDE_CONFIG, reg32); /* Set Interrupt Line */ diff --git a/src/southbridge/intel/i82801gx/i82801gx_lpc.c b/src/southbridge/intel/i82801gx/i82801gx_lpc.c index bed5dce2c2..a99e50e61e 100644 --- a/src/southbridge/intel/i82801gx/i82801gx_lpc.c +++ b/src/southbridge/intel/i82801gx/i82801gx_lpc.c @@ -36,36 +36,6 @@ typedef struct southbridge_intel_i82801gx_config config_t; -/* PIRQ[n]_ROUT[3:0] - PIRQ Routing Control - * 0x00 - 0000 = Reserved - * 0x01 - 0001 = Reserved - * 0x02 - 0010 = Reserved - * 0x03 - 0011 = IRQ3 - * 0x04 - 0100 = IRQ4 - * 0x05 - 0101 = IRQ5 - * 0x06 - 0110 = IRQ6 - * 0x07 - 0111 = IRQ7 - * 0x08 - 1000 = Reserved - * 0x09 - 1001 = IRQ9 - * 0x0A - 1010 = IRQ10 - * 0x0B - 1011 = IRQ11 - * 0x0C - 1100 = IRQ12 - * 0x0D - 1101 = Reserved - * 0x0E - 1110 = IRQ14 - * 0x0F - 1111 = IRQ15 - * PIRQ[n]_ROUT[7] - PIRQ Routing Control - * 0x80 - The PIRQ is not routed. - */ - -#define PIRQA 0x03 -#define PIRQB 0x05 -#define PIRQC 0x06 -#define PIRQD 0x07 -#define PIRQE 0x09 -#define PIRQF 0x0A -#define PIRQG 0x0B -#define PIRQH 0x0C - static void i82801gx_enable_apic(struct device *dev) { int i; @@ -206,6 +176,8 @@ static void i82801gx_power_options(device_t dev) u16 reg16, pmbase; u32 reg32; char *state; + /* Get the chip configuration */ + config_t *config = dev->chip_info; int pwr_on=CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL; int nmi_option; @@ -213,8 +185,12 @@ static void i82801gx_power_options(device_t dev) /* Which state do we want to goto after g3 (power restored)? * 0 == S0 Full On * 1 == S5 Soft Off + * + * If the option is not existent (Laptops), use MAINBOARD_POWER_ON. */ - get_option(&pwr_on, "power_on_after_fail"); + if (get_option(&pwr_on, "power_on_after_fail") < 0) + pwr_on = MAINBOARD_POWER_ON; + reg8 = pci_read_config8(dev, GEN_PMCON_3); reg8 &= 0xfe; switch (pwr_on) { @@ -265,19 +241,31 @@ static void i82801gx_power_options(device_t dev) reg16 &= ~((3 << 0) | (1 << 10)); reg16 |= (1 << 3) | (1 << 5); reg16 |= (1 << 2); // CLKRUN_EN +#if DEBUG_PERIODIC_SMIS + /* Set DEBUG_PERIODIC_SMIS in i82801gx.h to debug using + * periodic SMIs. + */ + reg16 |= (3 << 0); // Periodic SMI every 8s +#endif pci_write_config16(dev, GEN_PMCON_1, reg16); // Set the board's GPI routing. i82801gx_gpi_routing(dev); - /* Set up power management block and determine sleep mode */ pmbase = pci_read_config16(dev, 0x40) & 0xfffe; + + outl(config->gpe0_en, pmbase + GPE0_EN); + outw(config->alt_gp_smi_en, pmbase + ALT_GP_SMI_EN); + + /* Set up power management block and determine sleep mode */ reg32 = inl(pmbase + 0x04); // PM1_CNT +#if 0 #if CONFIG_HAVE_ACPI_RESUME acpi_slp_type = (((reg32 >> 10) & 7) == 5) ? 3 : 0; printk_debug("PM1_CNT: 0x%08x --> acpi_sleep_type: %x\n", reg32, acpi_slp_type); #endif +#endif reg32 |= (1 << 1); // enable C3->C0 transition on bus master reg32 |= 1; // SCI_EN outl(reg32, pmbase + 0x04); @@ -448,6 +436,9 @@ static void lpc_init(struct device *dev) setup_i8259(); + /* The OS should do this? */ + // i8259_configure_irq_trigger(9, 1); + #if CONFIG_HAVE_SMI_HANDLER i82801gx_lock_smm(dev); #endif diff --git a/src/southbridge/intel/i82801gx/i82801gx_nvs.h b/src/southbridge/intel/i82801gx/i82801gx_nvs.h index 7f245dd11a..dffee3f045 100644 --- a/src/southbridge/intel/i82801gx/i82801gx_nvs.h +++ b/src/southbridge/intel/i82801gx/i82801gx_nvs.h @@ -62,12 +62,12 @@ typedef struct { u8 rsvd4[5]; /* Super I/O & CMOS config */ u8 natp; /* 0x32 - SIO type */ - u8 cmap; - u8 cmbp; - u8 lptp; - u8 fdcp; - u8 rfdv; - u8 hotk; + u8 cmap; /* 0x33 - */ + u8 cmbp; /* 0x34 - */ + u8 lptp; /* 0x35 - LPT port */ + u8 fdcp; /* 0x36 - Floppy Disk Controller */ + u8 rfdv; /* 0x37 - */ + u8 hotk; /* 0x38 - Hot Key */ u8 rtcf; u8 util; u8 acin; @@ -134,6 +134,7 @@ typedef struct { u8 rsvd12[8]; /* Mainboard specific */ u8 dock; /* 0xf0 - Docking Status */ - u8 rsvd13[15]; + u8 bten; + u8 rsvd13[14]; } __attribute__((packed)) global_nvs_t; diff --git a/src/southbridge/intel/i82801gx/i82801gx_sata.c b/src/southbridge/intel/i82801gx/i82801gx_sata.c index ddfe08d25a..ec477e1696 100644 --- a/src/southbridge/intel/i82801gx/i82801gx_sata.c +++ b/src/southbridge/intel/i82801gx/i82801gx_sata.c @@ -68,7 +68,7 @@ static void sata_init(struct device *dev) pci_write_config16(dev, IDE_SDMA_TIM, 0x0200); /* Set IDE I/O Configuration */ - reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; + reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; pci_write_config32(dev, IDE_CONFIG, reg32); /* Combine IDE - SATA configuration */ @@ -100,7 +100,7 @@ static void sata_init(struct device *dev) pci_write_config16(dev, IDE_SDMA_TIM, 0x0001); /* Set IDE I/O Configuration */ - reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; + reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; pci_write_config32(dev, IDE_CONFIG, reg32); /* Set Sata Controller Mode. */ @@ -146,7 +146,7 @@ static void sata_init(struct device *dev) pci_write_config16(dev, IDE_SDMA_TIM, 0x0201); /* Set IDE I/O Configuration */ - reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; + reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; pci_write_config32(dev, IDE_CONFIG, reg32); /* Port 0 & 1 enable XXX */ diff --git a/src/southbridge/intel/i82801gx/i82801gx_smi.c b/src/southbridge/intel/i82801gx/i82801gx_smi.c index c8b5a16ccb..7fb4abfdaa 100644 --- a/src/southbridge/intel/i82801gx/i82801gx_smi.c +++ b/src/southbridge/intel/i82801gx/i82801gx_smi.c @@ -40,41 +40,6 @@ extern unsigned int smm_len; #define G_SMRAME (1 << 3) #define C_BASE_SEG ((0 << 2) | (1 << 1) | (0 << 0)) -/* ICH7 */ -#define PM1_STS 0x00 -#define PM1_EN 0x02 -#define PM1_CNT 0x04 -#define PM1_TMR 0x08 -#define PROC_CNT 0x10 -#define LV2 0x14 -#define LV3 0x15 -#define LV4 0x16 -#define PM2_CNT 0x20 // mobile only -#define GPE0_STS 0x28 -#define GPE0_EN 0x2c -#define SMI_EN 0x30 -#define EL_SMI_EN (1 << 25) // Intel Quick Resume Technology -#define INTEL_USB2_EN (1 << 18) // Intel-Specific USB2 SMI logic -#define LEGACY_USB2_EN (1 << 17) // Legacy USB2 SMI logic -#define PERIODIC_EN (1 << 14) // SMI on PERIODIC_STS in SMI_STS -#define TCO_EN (1 << 13) // Enable TCO Logic (BIOSWE et al) -#define MCSMI_EN (1 << 11) // Trap microcontroller range access -#define BIOS_RLS (1 << 7) // asserts SCI on bit set -#define SWSMI_TMR_EN (1 << 6) // start software smi timer on bit set -#define APMC_EN (1 << 5) // Writes to APM_CNT cause SMI# -#define SLP_SMI_EN (1 << 4) // Write to SLP_EN in PM1_CNT asserts SMI# -#define LEGACY_USB_EN (1 << 3) // Legacy USB circuit SMI logic -#define BIOS_EN (1 << 2) // Assert SMI# on setting GBL_RLS bit -#define EOS (1 << 1) // End of SMI (deassert SMI#) -#define GBL_SMI_EN (1 << 0) // SMI# generation at all? -#define SMI_STS 0x34 -#define ALT_GP_SMI_EN 0x38 -#define ALT_GP_SMI_STS 0x3a -#define GPE_CNTL 0x42 -#define DEVACT_STS 0x44 -#define SS_CNT 0x50 -#define C3_RES 0x54 - /* While we read PMBASE dynamically in case it changed, let's * initialize it with a sane value */ @@ -277,8 +242,23 @@ void smm_relocate(void) * No SMIs: * - on microcontroller writes (io 0x62/0x66) */ - outl(smi_en | (TCO_EN | APMC_EN | SLP_SMI_EN | BIOS_EN | - EOS | GBL_SMI_EN), pmbase + SMI_EN); + + smi_en = 0; /* reset SMI enables */ + smi_en |= TCO_EN; + smi_en |= APMC_EN; +#if DEBUG_PERIODIC_SMIS + /* Set DEBUG_PERIODIC_SMIS in i82801gx.h to debug using + * periodic SMIs. + */ + smi_en |= PERIODIC_EN; +#endif + smi_en |= SLP_SMI_EN; + smi_en |= BIOS_EN; + + /* The following need to be on for SMIs to happen */ + smi_en |= EOS | GBL_SMI_EN; + + outl(smi_en, pmbase + SMI_EN); /** * There are several methods of raising a controlled SMI# via diff --git a/src/southbridge/intel/i82801gx/i82801gx_smihandler.c b/src/southbridge/intel/i82801gx/i82801gx_smihandler.c index 56ce0fe0eb..8cf39e8ded 100644 --- a/src/southbridge/intel/i82801gx/i82801gx_smihandler.c +++ b/src/southbridge/intel/i82801gx/i82801gx_smihandler.c @@ -46,53 +46,13 @@ #define G_SMRANE (1 << 3) #define C_BASE_SEG ((0 << 2) | (1 << 1) | (0 << 0)) -/* ICH7 */ -#define PM1_STS 0x00 -#define PM1_EN 0x02 -#define PM1_CNT 0x04 -#define SLP_EN (1 << 13) -#define SLP_TYP (7 << 10) -#define GBL_RLS (1 << 2) -#define BM_RLD (1 << 1) -#define SCI_EN (1 << 0) -#define PM1_TMR 0x08 -#define PROC_CNT 0x10 -#define LV2 0x14 -#define LV3 0x15 -#define LV4 0x16 -#define PM2_CNT 0x20 // mobile only -#define GPE0_STS 0x28 -#define GPE0_EN 0x2c -#define PME_B0_EN (1 << 13) -#define SMI_EN 0x30 -#define EL_SMI_EN (1 << 25) // Intel Quick Resume Technology -#define INTEL_USB2_EN (1 << 18) // Intel-Specific USB2 SMI logic -#define LEGACY_USB2_EN (1 << 17) // Legacy USB2 SMI logic -#define PERIODIC_EN (1 << 14) // SMI on PERIODIC_STS in SMI_STS -#define TCO_EN (1 << 13) // Enable TCO Logic (BIOSWE et al) -#define MCSMI_EN (1 << 11) // Trap microcontroller range access -#define BIOS_RLS (1 << 7) // asserts SCI on bit set -#define SWSMI_TMR_EN (1 << 6) // start software smi timer on bit set -#define APMC_EN (1 << 5) // Writes to APM_CNT cause SMI# -#define SLP_SMI_EN (1 << 4) // Write to SLP_EN in PM1_CNT asserts SMI# -#define LEGACY_USB_EN (1 << 3) // Legacy USB circuit SMI logic -#define BIOS_EN (1 << 2) // Assert SMI# on setting GBL_RLS bit -#define EOS (1 << 1) // End of SMI (deassert SMI#) -#define GBL_SMI_EN (1 << 0) // SMI# generation at all? -#define SMI_STS 0x34 -#define ALT_GP_SMI_EN 0x38 -#define ALT_GP_SMI_STS 0x3a -#define GPE_CNTL 0x42 -#define DEVACT_STS 0x44 -#define SS_CNT 0x50 -#define C3_RES 0x54 - #include "i82801gx_nvs.h" /* While we read PMBASE dynamically in case it changed, let's * initialize it with a sane value */ u16 pmbase = DEFAULT_PMBASE; +u8 smm_initialized = 0; /* GNVS needs to be updated by an 0xEA PM Trap (B2) after it has been located * by coreboot. @@ -118,16 +78,16 @@ static u16 reset_pm1_status(void) static void dump_pm1_status(u16 pm1_sts) { - printk_debug("PM1_STS: "); - if (pm1_sts & (1 << 15)) printk_debug("WAK "); - if (pm1_sts & (1 << 14)) printk_debug("PCIEXPWAK "); - if (pm1_sts & (1 << 11)) printk_debug("PRBTNOR "); - if (pm1_sts & (1 << 10)) printk_debug("RTC "); - if (pm1_sts & (1 << 8)) printk_debug("PWRBTN "); - if (pm1_sts & (1 << 5)) printk_debug("GBL "); - if (pm1_sts & (1 << 4)) printk_debug("BM "); - if (pm1_sts & (1 << 0)) printk_debug("TMROF "); - printk_debug("\n"); + printk_spew("PM1_STS: "); + if (pm1_sts & (1 << 15)) printk_spew("WAK "); + if (pm1_sts & (1 << 14)) printk_spew("PCIEXPWAK "); + if (pm1_sts & (1 << 11)) printk_spew("PRBTNOR "); + if (pm1_sts & (1 << 10)) printk_spew("RTC "); + if (pm1_sts & (1 << 8)) printk_spew("PWRBTN "); + if (pm1_sts & (1 << 5)) printk_spew("GBL "); + if (pm1_sts & (1 << 4)) printk_spew("BM "); + if (pm1_sts & (1 << 0)) printk_spew("TMROF "); + printk_spew("\n"); } /** @@ -261,21 +221,16 @@ int southbridge_io_trap_handler(int smif) switch (smif) { case 0x32: printk_debug("OS Init\n"); + /* gnvs->smif: + * On success, the IO Trap Handler returns 0 + * On failure, the IO Trap Handler returns a value != 0 + */ gnvs->smif = 0; - break; - default: - /* Not handled */ - return 0; + return 1; /* IO trap handled */ } - /* On success, the IO Trap Handler returns 0 - * On failure, the IO Trap Handler returns a value != 0 - * - * For now, we force the return value to 0 and log all traps to - * see what's going on. - */ - //gnvs->smif = 0; - return 1; /* IO trap handled */ + /* Not handled */ + return 0; } /** @@ -400,9 +355,14 @@ static void southbridge_smi_apmc(unsigned int node, smm_state_save_area_t *state printk_debug("SMI#: ACPI enabled.\n"); break; case GNVS_UPDATE: + if (smm_initialized) { + printk_debug("SMI#: SMM structures already initialized!\n"); + return; + } gnvs = *(global_nvs_t **)0x500; tcg = *(void **)0x504; smi1 = *(void **)0x508; + smm_initialized = 1; printk_debug("SMI#: Setting up structures to %p, %p, %p\n", gnvs, tcg, smi1); break; default: @@ -426,6 +386,17 @@ static void southbridge_smi_gpe0(unsigned int node, smm_state_save_area_t *state dump_gpe0_status(gpe0_sts); } +static void southbridge_smi_gpi(unsigned int node, smm_state_save_area_t *state_save) +{ + u16 reg16; + reg16 = inw(pmbase + ALT_GP_SMI_STS); + outl(reg16, pmbase + ALT_GP_SMI_STS); + + reg16 &= inw(pmbase + ALT_GP_SMI_EN); + if (reg16) + printk_debug("GPI (mask %04x)\n",reg16); +} + static void southbridge_smi_mc(unsigned int node, smm_state_save_area_t *state_save) { u32 reg32; @@ -559,7 +530,7 @@ smi_handler southbridge_smi[32] = { NULL, // [7] reserved southbridge_smi_pm1, // [8] PM1_STS southbridge_smi_gpe0, // [9] GPE0_STS - NULL, // [10] GPI_STS + southbridge_smi_gpi, // [10] GPI_STS southbridge_smi_mc, // [11] MCSMI_STS NULL, // [12] DEVMON_STS southbridge_smi_tco, // [13] TCO_STS |