diff options
| -rw-r--r-- | src/mainboard/google/nyan/mainboard.c | 61 | ||||
| -rw-r--r-- | src/mainboard/google/nyan/romstage.c | 88 | ||||
| -rw-r--r-- | src/mainboard/google/nyan_big/mainboard.c | 62 | ||||
| -rw-r--r-- | src/mainboard/google/nyan_big/romstage.c | 88 | ||||
| -rw-r--r-- | src/mainboard/google/nyan_blaze/mainboard.c | 62 | ||||
| -rw-r--r-- | src/mainboard/google/nyan_blaze/romstage.c | 88 |
6 files changed, 266 insertions, 183 deletions
diff --git a/src/mainboard/google/nyan/mainboard.c b/src/mainboard/google/nyan/mainboard.c index f521dcc4ef..dbca03ccae 100644 --- a/src/mainboard/google/nyan/mainboard.c +++ b/src/mainboard/google/nyan/mainboard.c @@ -39,14 +39,6 @@ static void set_clock_sources(void) * can both run at 400 KHz, but the kernel sets the bus to 100 KHz. */ clock_configure_i2c_scl_freq(i2c1, PLLP, 100); - /* - * The TPM is on I2C3 and can theoretically run at 400 KHz but doesn't - * seem to work above around 40 KHz. It's set to run at 100 KHz in the - * kernel. - */ - clock_configure_i2c_scl_freq(i2c3, PLLP, 40); - - clock_configure_source(sbc1, PLLP, 5000); /* * MMC3 and MMC4: Set base clock frequency for SD Clock to Tegra MMC's @@ -78,47 +70,6 @@ static void set_clock_sources(void) static void setup_pinmux(void) { - // Write protect. - gpio_input_pullup(GPIO(R1)); - // Recovery mode. - gpio_input_pullup(GPIO(Q7)); - // Lid switch. - gpio_input_pullup(GPIO(R4)); - // Power switch. - gpio_input_pullup(GPIO(Q0)); - // Developer mode. - gpio_input_pullup(GPIO(Q6)); - // EC in RW. - gpio_input_pullup(GPIO(U4)); - - // SOC and TPM reset GPIO, active low. - gpio_output(GPIO(I5), 1); - - // SPI1 MOSI - pinmux_set_config(PINMUX_ULPI_CLK_INDEX, PINMUX_ULPI_CLK_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 MISO - pinmux_set_config(PINMUX_ULPI_DIR_INDEX, PINMUX_ULPI_DIR_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 SCLK - pinmux_set_config(PINMUX_ULPI_NXT_INDEX, PINMUX_ULPI_NXT_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 CS0 - pinmux_set_config(PINMUX_ULPI_STP_INDEX, PINMUX_ULPI_STP_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - - // switch unused pin to GPIO - gpio_set_mode(GPIO(X3), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X4), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X5), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X6), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X7), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(W3), GPIO_MODE_GPIO); - // I2C1 clock. pinmux_set_config(PINMUX_GEN1_I2C_SCL_INDEX, PINMUX_GEN1_I2C_SCL_FUNC_I2C1 | PINMUX_INPUT_ENABLE); @@ -131,12 +82,6 @@ static void setup_pinmux(void) // I2C2 data. pinmux_set_config(PINMUX_GEN2_I2C_SDA_INDEX, PINMUX_GEN2_I2C_SDA_FUNC_I2C2 | PINMUX_INPUT_ENABLE); - // I2C3 (cam) clock. - pinmux_set_config(PINMUX_CAM_I2C_SCL_INDEX, - PINMUX_CAM_I2C_SCL_FUNC_I2C3 | PINMUX_INPUT_ENABLE); - // I2C3 (cam) data. - pinmux_set_config(PINMUX_CAM_I2C_SDA_INDEX, - PINMUX_CAM_I2C_SDA_FUNC_I2C3 | PINMUX_INPUT_ENABLE); // I2C4 (DDC) clock. pinmux_set_config(PINMUX_DDC_SCL_INDEX, PINMUX_DDC_SCL_FUNC_I2C4 | PINMUX_INPUT_ENABLE); @@ -271,10 +216,9 @@ static void mainboard_init(device_t dev) CLK_L_SPDIF | CLK_L_USBD | CLK_L_DISP1 | CLK_L_HOST1X | CLK_L_PWM, - CLK_H_I2C2 | CLK_H_SBC1 | CLK_H_PMC | - CLK_H_USB3, + CLK_H_I2C2 | CLK_H_PMC | CLK_H_USB3, - CLK_U_I2C3 | CLK_U_CSITE | CLK_U_SDMMC3, + CLK_U_CSITE | CLK_U_SDMMC3, CLK_V_I2C4 | CLK_V_EXTPERIPH1 | CLK_V_APBIF | CLK_V_AUDIO | CLK_V_I2S3 | CLK_V_I2S4 | @@ -295,7 +239,6 @@ static void mainboard_init(device_t dev) i2c_init(0); i2c_init(1); - i2c_init(2); i2c_init(3); setup_kernel_info(); diff --git a/src/mainboard/google/nyan/romstage.c b/src/mainboard/google/nyan/romstage.c index 175eb6fc3e..ee54a50ef7 100644 --- a/src/mainboard/google/nyan/romstage.c +++ b/src/mainboard/google/nyan/romstage.c @@ -20,17 +20,24 @@ #include <arch/cache.h> #include <arch/cpu.h> #include <arch/exception.h> +#include <arch/io.h> #include <arch/stages.h> #include <device/device.h> #include <cbfs.h> #include <cbmem.h> #include <console/console.h> #include "sdram_configs.h" -#include "soc/nvidia/tegra124/chip.h" -#include "soc/nvidia/tegra124/sdram.h" +#include <soc/nvidia/tegra/i2c.h> +#include <soc/nvidia/tegra124/chip.h> +#include <soc/nvidia/tegra124/clk_rst.h> +#include <soc/nvidia/tegra124/sdram.h> +#include <soc/addressmap.h> +#include <soc/clock.h> #include <soc/display.h> #include <timestamp.h> +static struct clk_rst_ctlr *clk_rst = (void *)TEGRA_CLK_RST_BASE; + enum { L2CTLR_ECC_PARITY = 0x1 << 21, L2CTLR_TAG_RAM_LATENCY_MASK = 0x7 << 6, @@ -69,6 +76,74 @@ static void configure_l2actlr(void) write_l2actlr(val); } +static void setup_pinmux(void) +{ + // Write protect. + gpio_input_pullup(GPIO(R1)); + // Recovery mode. + gpio_input_pullup(GPIO(Q7)); + // Lid switch. + gpio_input_pullup(GPIO(R4)); + // Power switch. + gpio_input_pullup(GPIO(Q0)); + // Developer mode. + gpio_input_pullup(GPIO(Q6)); + // EC in RW. + gpio_input_pullup(GPIO(U4)); + + // SOC and TPM reset GPIO, active low. + gpio_output(GPIO(I5), 1); + + // SPI1 MOSI + pinmux_set_config(PINMUX_ULPI_CLK_INDEX, PINMUX_ULPI_CLK_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 MISO + pinmux_set_config(PINMUX_ULPI_DIR_INDEX, PINMUX_ULPI_DIR_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 SCLK + pinmux_set_config(PINMUX_ULPI_NXT_INDEX, PINMUX_ULPI_NXT_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 CS0 + pinmux_set_config(PINMUX_ULPI_STP_INDEX, PINMUX_ULPI_STP_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + + // I2C3 (cam) clock. + pinmux_set_config(PINMUX_CAM_I2C_SCL_INDEX, + PINMUX_CAM_I2C_SCL_FUNC_I2C3 | PINMUX_INPUT_ENABLE); + // I2C3 (cam) data. + pinmux_set_config(PINMUX_CAM_I2C_SDA_INDEX, + PINMUX_CAM_I2C_SDA_FUNC_I2C3 | PINMUX_INPUT_ENABLE); + + // switch unused pin to GPIO + gpio_set_mode(GPIO(X3), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X4), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X5), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X6), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X7), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(W3), GPIO_MODE_GPIO); +} + +static void configure_ec_spi_bus(void) +{ + clock_configure_source(sbc1, PLLP, 5000); +} + +static void configure_tpm_i2c_bus(void) +{ + /* + * The TPM is on I2C3 and can theoretically run at 400 KHz but doesn't + * seem to work above around 40 KHz. It's set to run at 100 KHz in the + * kernel. + */ + clock_configure_i2c_scl_freq(i2c3, PLLP, 40); + + i2c_init(2); +} + static void __attribute__((noinline)) romstage(void) { #if CONFIG_COLLECT_TIMESTAMPS @@ -130,6 +205,15 @@ static void __attribute__((noinline)) romstage(void) timestamp_add(TS_START_ROMSTAGE, romstage_start_time); timestamp_add(TS_START_COPYRAM, timestamp_get()); #endif + + // Enable additional peripherals we need for ROM stage. + clock_enable_clear_reset(0, CLK_H_SBC1, CLK_U_I2C3, 0, 0, 0); + + setup_pinmux(); + + configure_ec_spi_bus(); + configure_tpm_i2c_bus(); + void *entry = cbfs_load_stage(CBFS_DEFAULT_MEDIA, "fallback/coreboot_ram"); #if CONFIG_COLLECT_TIMESTAMPS diff --git a/src/mainboard/google/nyan_big/mainboard.c b/src/mainboard/google/nyan_big/mainboard.c index c77afd2c5a..997ceb0c2e 100644 --- a/src/mainboard/google/nyan_big/mainboard.c +++ b/src/mainboard/google/nyan_big/mainboard.c @@ -39,14 +39,6 @@ static void set_clock_sources(void) * can both run at 400 KHz, but the kernel sets the bus to 100 KHz. */ clock_configure_i2c_scl_freq(i2c1, PLLP, 100); - /* - * The TPM is on I2C3 and can theoretically run at 400 KHz but doesn't - * seem to work above around 40 KHz. It's set to run at 100 KHz in the - * kernel. - */ - clock_configure_i2c_scl_freq(i2c3, PLLP, 40); - - clock_configure_source(sbc1, PLLP, 5000); /* * MMC3 and MMC4: Set base clock frequency for SD Clock to Tegra MMC's @@ -78,47 +70,6 @@ static void set_clock_sources(void) static void setup_pinmux(void) { - // Write protect. - gpio_input_pullup(GPIO(R1)); - // Recovery mode. - gpio_input_pullup(GPIO(Q7)); - // Lid switch. - gpio_input_pullup(GPIO(R4)); - // Power switch. - gpio_input_pullup(GPIO(Q0)); - // Developer mode. - gpio_input_pullup(GPIO(Q6)); - // EC in RW. - gpio_input_pullup(GPIO(U4)); - - // SOC and TPM reset GPIO, active low. - gpio_output(GPIO(I5), 1); - - // SPI1 MOSI - pinmux_set_config(PINMUX_ULPI_CLK_INDEX, PINMUX_ULPI_CLK_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 MISO - pinmux_set_config(PINMUX_ULPI_DIR_INDEX, PINMUX_ULPI_DIR_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 SCLK - pinmux_set_config(PINMUX_ULPI_NXT_INDEX, PINMUX_ULPI_NXT_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 CS0 - pinmux_set_config(PINMUX_ULPI_STP_INDEX, PINMUX_ULPI_STP_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - - // switch unused pin to GPIO - gpio_set_mode(GPIO(X3), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X4), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X5), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X6), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X7), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(W3), GPIO_MODE_GPIO); - // I2C1 clock. pinmux_set_config(PINMUX_GEN1_I2C_SCL_INDEX, PINMUX_GEN1_I2C_SCL_FUNC_I2C1 | PINMUX_INPUT_ENABLE); @@ -131,12 +82,6 @@ static void setup_pinmux(void) // I2C2 data. pinmux_set_config(PINMUX_GEN2_I2C_SDA_INDEX, PINMUX_GEN2_I2C_SDA_FUNC_I2C2 | PINMUX_INPUT_ENABLE); - // I2C3 (cam) clock. - pinmux_set_config(PINMUX_CAM_I2C_SCL_INDEX, - PINMUX_CAM_I2C_SCL_FUNC_I2C3 | PINMUX_INPUT_ENABLE); - // I2C3 (cam) data. - pinmux_set_config(PINMUX_CAM_I2C_SDA_INDEX, - PINMUX_CAM_I2C_SDA_FUNC_I2C3 | PINMUX_INPUT_ENABLE); // I2C4 (DDC) clock. pinmux_set_config(PINMUX_DDC_SCL_INDEX, PINMUX_DDC_SCL_FUNC_I2C4 | PINMUX_INPUT_ENABLE); @@ -268,10 +213,10 @@ static void mainboard_init(device_t dev) CLK_L_SPDIF | CLK_L_USBD | CLK_L_DISP1 | CLK_L_HOST1X | CLK_L_PWM, - CLK_H_EMC | CLK_H_I2C2 | CLK_H_SBC1 | - CLK_H_PMC | CLK_H_MEM | CLK_H_USB3, + CLK_H_EMC | CLK_H_I2C2 | CLK_H_PMC | + CLK_H_MEM | CLK_H_USB3, - CLK_U_I2C3 | CLK_U_CSITE | CLK_U_SDMMC3, + CLK_U_CSITE | CLK_U_SDMMC3, CLK_V_I2C4 | CLK_V_EXTPERIPH1 | CLK_V_APBIF | CLK_V_AUDIO | CLK_V_I2S3 | CLK_V_I2S4 | @@ -292,7 +237,6 @@ static void mainboard_init(device_t dev) i2c_init(0); i2c_init(1); - i2c_init(2); i2c_init(3); setup_kernel_info(); diff --git a/src/mainboard/google/nyan_big/romstage.c b/src/mainboard/google/nyan_big/romstage.c index 51f5a49264..e1597c8ba9 100644 --- a/src/mainboard/google/nyan_big/romstage.c +++ b/src/mainboard/google/nyan_big/romstage.c @@ -20,17 +20,24 @@ #include <arch/cache.h> #include <arch/cpu.h> #include <arch/exception.h> +#include <arch/io.h> #include <arch/stages.h> #include <device/device.h> #include <cbfs.h> #include <cbmem.h> #include <console/console.h> #include "sdram_configs.h" -#include "soc/nvidia/tegra124/chip.h" -#include "soc/nvidia/tegra124/sdram.h" +#include <soc/nvidia/tegra/i2c.h> +#include <soc/nvidia/tegra124/chip.h> +#include <soc/nvidia/tegra124/clk_rst.h> +#include <soc/nvidia/tegra124/sdram.h> +#include <soc/addressmap.h> +#include <soc/clock.h> #include <soc/display.h> #include <timestamp.h> +static struct clk_rst_ctlr *clk_rst = (void *)TEGRA_CLK_RST_BASE; + enum { L2CTLR_ECC_PARITY = 0x1 << 21, L2CTLR_TAG_RAM_LATENCY_MASK = 0x7 << 6, @@ -69,6 +76,74 @@ static void configure_l2actlr(void) write_l2actlr(val); } +static void setup_pinmux(void) +{ + // Write protect. + gpio_input_pullup(GPIO(R1)); + // Recovery mode. + gpio_input_pullup(GPIO(Q7)); + // Lid switch. + gpio_input_pullup(GPIO(R4)); + // Power switch. + gpio_input_pullup(GPIO(Q0)); + // Developer mode. + gpio_input_pullup(GPIO(Q6)); + // EC in RW. + gpio_input_pullup(GPIO(U4)); + + // SOC and TPM reset GPIO, active low. + gpio_output(GPIO(I5), 1); + + // SPI1 MOSI + pinmux_set_config(PINMUX_ULPI_CLK_INDEX, PINMUX_ULPI_CLK_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 MISO + pinmux_set_config(PINMUX_ULPI_DIR_INDEX, PINMUX_ULPI_DIR_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 SCLK + pinmux_set_config(PINMUX_ULPI_NXT_INDEX, PINMUX_ULPI_NXT_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 CS0 + pinmux_set_config(PINMUX_ULPI_STP_INDEX, PINMUX_ULPI_STP_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + + // I2C3 (cam) clock. + pinmux_set_config(PINMUX_CAM_I2C_SCL_INDEX, + PINMUX_CAM_I2C_SCL_FUNC_I2C3 | PINMUX_INPUT_ENABLE); + // I2C3 (cam) data. + pinmux_set_config(PINMUX_CAM_I2C_SDA_INDEX, + PINMUX_CAM_I2C_SDA_FUNC_I2C3 | PINMUX_INPUT_ENABLE); + + // switch unused pin to GPIO + gpio_set_mode(GPIO(X3), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X4), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X5), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X6), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X7), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(W3), GPIO_MODE_GPIO); +} + +static void configure_ec_spi_bus(void) +{ + clock_configure_source(sbc1, PLLP, 5000); +} + +static void configure_tpm_i2c_bus(void) +{ + /* + * The TPM is on I2C3 and can theoretically run at 400 KHz but doesn't + * seem to work above around 40 KHz. It's set to run at 100 KHz in the + * kernel. + */ + clock_configure_i2c_scl_freq(i2c3, PLLP, 40); + + i2c_init(2); +} + static void __attribute__((noinline)) romstage(void) { #if CONFIG_COLLECT_TIMESTAMPS @@ -130,6 +205,15 @@ static void __attribute__((noinline)) romstage(void) timestamp_add(TS_START_ROMSTAGE, romstage_start_time); timestamp_add(TS_START_COPYRAM, timestamp_get()); #endif + + // Enable additional peripherals we need for ROM stage. + clock_enable_clear_reset(0, CLK_H_SBC1, CLK_U_I2C3, 0, 0, 0); + + setup_pinmux(); + + configure_ec_spi_bus(); + configure_tpm_i2c_bus(); + void *entry = cbfs_load_stage(CBFS_DEFAULT_MEDIA, "fallback/coreboot_ram"); #if CONFIG_COLLECT_TIMESTAMPS diff --git a/src/mainboard/google/nyan_blaze/mainboard.c b/src/mainboard/google/nyan_blaze/mainboard.c index 11c60ef9bc..dc105c6976 100644 --- a/src/mainboard/google/nyan_blaze/mainboard.c +++ b/src/mainboard/google/nyan_blaze/mainboard.c @@ -39,14 +39,6 @@ static void set_clock_sources(void) * can both run at 400 KHz, but the kernel sets the bus to 100 KHz. */ clock_configure_i2c_scl_freq(i2c1, PLLP, 100); - /* - * The TPM is on I2C3 and can theoretically run at 400 KHz but doesn't - * seem to work above around 40 KHz. It's set to run at 100 KHz in the - * kernel. - */ - clock_configure_i2c_scl_freq(i2c3, PLLP, 40); - - clock_configure_source(sbc1, PLLP, 5000); /* * MMC3 and MMC4: Set base clock frequency for SD Clock to Tegra MMC's @@ -78,47 +70,6 @@ static void set_clock_sources(void) static void setup_pinmux(void) { - // Write protect. - gpio_input_pullup(GPIO(R1)); - // Recovery mode. - gpio_input_pullup(GPIO(Q7)); - // Lid switch. - gpio_input_pullup(GPIO(R4)); - // Power switch. - gpio_input_pullup(GPIO(Q0)); - // Developer mode. - gpio_input_pullup(GPIO(Q6)); - // EC in RW. - gpio_input_pullup(GPIO(U4)); - - // SOC and TPM reset GPIO, active low. - gpio_output(GPIO(I5), 1); - - // SPI1 MOSI - pinmux_set_config(PINMUX_ULPI_CLK_INDEX, PINMUX_ULPI_CLK_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 MISO - pinmux_set_config(PINMUX_ULPI_DIR_INDEX, PINMUX_ULPI_DIR_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 SCLK - pinmux_set_config(PINMUX_ULPI_NXT_INDEX, PINMUX_ULPI_NXT_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - // SPI1 CS0 - pinmux_set_config(PINMUX_ULPI_STP_INDEX, PINMUX_ULPI_STP_FUNC_SPI1 | - PINMUX_PULL_NONE | - PINMUX_INPUT_ENABLE); - - // switch unused pin to GPIO - gpio_set_mode(GPIO(X3), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X4), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X5), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X6), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(X7), GPIO_MODE_GPIO); - gpio_set_mode(GPIO(W3), GPIO_MODE_GPIO); - // I2C1 clock. pinmux_set_config(PINMUX_GEN1_I2C_SCL_INDEX, PINMUX_GEN1_I2C_SCL_FUNC_I2C1 | PINMUX_INPUT_ENABLE); @@ -131,12 +82,6 @@ static void setup_pinmux(void) // I2C2 data. pinmux_set_config(PINMUX_GEN2_I2C_SDA_INDEX, PINMUX_GEN2_I2C_SDA_FUNC_I2C2 | PINMUX_INPUT_ENABLE); - // I2C3 (cam) clock. - pinmux_set_config(PINMUX_CAM_I2C_SCL_INDEX, - PINMUX_CAM_I2C_SCL_FUNC_I2C3 | PINMUX_INPUT_ENABLE); - // I2C3 (cam) data. - pinmux_set_config(PINMUX_CAM_I2C_SDA_INDEX, - PINMUX_CAM_I2C_SDA_FUNC_I2C3 | PINMUX_INPUT_ENABLE); // I2C4 (DDC) clock. pinmux_set_config(PINMUX_DDC_SCL_INDEX, PINMUX_DDC_SCL_FUNC_I2C4 | PINMUX_INPUT_ENABLE); @@ -268,10 +213,10 @@ static void mainboard_init(device_t dev) CLK_L_SPDIF | CLK_L_USBD | CLK_L_DISP1 | CLK_L_HOST1X | CLK_L_PWM, - CLK_H_EMC | CLK_H_I2C2 | CLK_H_SBC1 | - CLK_H_PMC | CLK_H_MEM | CLK_H_USB3, + CLK_H_EMC | CLK_H_I2C2 | CLK_H_PMC | + CLK_H_MEM | CLK_H_USB3, - CLK_U_I2C3 | CLK_U_CSITE | CLK_U_SDMMC3, + CLK_U_CSITE | CLK_U_SDMMC3, CLK_V_I2C4 | CLK_V_EXTPERIPH1 | CLK_V_APBIF | CLK_V_AUDIO | CLK_V_I2S3 | CLK_V_I2S4 | @@ -292,7 +237,6 @@ static void mainboard_init(device_t dev) i2c_init(0); i2c_init(1); - i2c_init(2); i2c_init(3); setup_kernel_info(); diff --git a/src/mainboard/google/nyan_blaze/romstage.c b/src/mainboard/google/nyan_blaze/romstage.c index 51f5a49264..e1597c8ba9 100644 --- a/src/mainboard/google/nyan_blaze/romstage.c +++ b/src/mainboard/google/nyan_blaze/romstage.c @@ -20,17 +20,24 @@ #include <arch/cache.h> #include <arch/cpu.h> #include <arch/exception.h> +#include <arch/io.h> #include <arch/stages.h> #include <device/device.h> #include <cbfs.h> #include <cbmem.h> #include <console/console.h> #include "sdram_configs.h" -#include "soc/nvidia/tegra124/chip.h" -#include "soc/nvidia/tegra124/sdram.h" +#include <soc/nvidia/tegra/i2c.h> +#include <soc/nvidia/tegra124/chip.h> +#include <soc/nvidia/tegra124/clk_rst.h> +#include <soc/nvidia/tegra124/sdram.h> +#include <soc/addressmap.h> +#include <soc/clock.h> #include <soc/display.h> #include <timestamp.h> +static struct clk_rst_ctlr *clk_rst = (void *)TEGRA_CLK_RST_BASE; + enum { L2CTLR_ECC_PARITY = 0x1 << 21, L2CTLR_TAG_RAM_LATENCY_MASK = 0x7 << 6, @@ -69,6 +76,74 @@ static void configure_l2actlr(void) write_l2actlr(val); } +static void setup_pinmux(void) +{ + // Write protect. + gpio_input_pullup(GPIO(R1)); + // Recovery mode. + gpio_input_pullup(GPIO(Q7)); + // Lid switch. + gpio_input_pullup(GPIO(R4)); + // Power switch. + gpio_input_pullup(GPIO(Q0)); + // Developer mode. + gpio_input_pullup(GPIO(Q6)); + // EC in RW. + gpio_input_pullup(GPIO(U4)); + + // SOC and TPM reset GPIO, active low. + gpio_output(GPIO(I5), 1); + + // SPI1 MOSI + pinmux_set_config(PINMUX_ULPI_CLK_INDEX, PINMUX_ULPI_CLK_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 MISO + pinmux_set_config(PINMUX_ULPI_DIR_INDEX, PINMUX_ULPI_DIR_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 SCLK + pinmux_set_config(PINMUX_ULPI_NXT_INDEX, PINMUX_ULPI_NXT_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + // SPI1 CS0 + pinmux_set_config(PINMUX_ULPI_STP_INDEX, PINMUX_ULPI_STP_FUNC_SPI1 | + PINMUX_PULL_NONE | + PINMUX_INPUT_ENABLE); + + // I2C3 (cam) clock. + pinmux_set_config(PINMUX_CAM_I2C_SCL_INDEX, + PINMUX_CAM_I2C_SCL_FUNC_I2C3 | PINMUX_INPUT_ENABLE); + // I2C3 (cam) data. + pinmux_set_config(PINMUX_CAM_I2C_SDA_INDEX, + PINMUX_CAM_I2C_SDA_FUNC_I2C3 | PINMUX_INPUT_ENABLE); + + // switch unused pin to GPIO + gpio_set_mode(GPIO(X3), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X4), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X5), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X6), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(X7), GPIO_MODE_GPIO); + gpio_set_mode(GPIO(W3), GPIO_MODE_GPIO); +} + +static void configure_ec_spi_bus(void) +{ + clock_configure_source(sbc1, PLLP, 5000); +} + +static void configure_tpm_i2c_bus(void) +{ + /* + * The TPM is on I2C3 and can theoretically run at 400 KHz but doesn't + * seem to work above around 40 KHz. It's set to run at 100 KHz in the + * kernel. + */ + clock_configure_i2c_scl_freq(i2c3, PLLP, 40); + + i2c_init(2); +} + static void __attribute__((noinline)) romstage(void) { #if CONFIG_COLLECT_TIMESTAMPS @@ -130,6 +205,15 @@ static void __attribute__((noinline)) romstage(void) timestamp_add(TS_START_ROMSTAGE, romstage_start_time); timestamp_add(TS_START_COPYRAM, timestamp_get()); #endif + + // Enable additional peripherals we need for ROM stage. + clock_enable_clear_reset(0, CLK_H_SBC1, CLK_U_I2C3, 0, 0, 0); + + setup_pinmux(); + + configure_ec_spi_bus(); + configure_tpm_i2c_bus(); + void *entry = cbfs_load_stage(CBFS_DEFAULT_MEDIA, "fallback/coreboot_ram"); #if CONFIG_COLLECT_TIMESTAMPS |