diff options
| -rw-r--r-- | src/northbridge/intel/e7501/Kconfig | 4 | ||||
| -rw-r--r-- | src/northbridge/intel/e7501/Makefile.inc | 5 | ||||
| -rw-r--r-- | src/northbridge/intel/e7501/debug.c | 175 | ||||
| -rw-r--r-- | src/northbridge/intel/e7501/e7501.h | 80 | ||||
| -rw-r--r-- | src/northbridge/intel/e7501/northbridge.c | 140 | ||||
| -rw-r--r-- | src/northbridge/intel/e7501/raminit.c | 2009 | ||||
| -rw-r--r-- | src/northbridge/intel/e7501/raminit.h | 20 | ||||
| -rw-r--r-- | src/northbridge/intel/e7501/reset_test.c | 18 |
8 files changed, 0 insertions, 2451 deletions
diff --git a/src/northbridge/intel/e7501/Kconfig b/src/northbridge/intel/e7501/Kconfig deleted file mode 100644 index 91af6c464b..0000000000 --- a/src/northbridge/intel/e7501/Kconfig +++ /dev/null @@ -1,4 +0,0 @@ -config NORTHBRIDGE_INTEL_E7501 - bool - select HAVE_DEBUG_RAM_SETUP - select LATE_CBMEM_INIT diff --git a/src/northbridge/intel/e7501/Makefile.inc b/src/northbridge/intel/e7501/Makefile.inc deleted file mode 100644 index 756dc89712..0000000000 --- a/src/northbridge/intel/e7501/Makefile.inc +++ /dev/null @@ -1,5 +0,0 @@ -ifeq ($(CONFIG_NORTHBRIDGE_INTEL_E7501),y) - -ramstage-y += northbridge.c - -endif diff --git a/src/northbridge/intel/e7501/debug.c b/src/northbridge/intel/e7501/debug.c deleted file mode 100644 index 9d79c9b91b..0000000000 --- a/src/northbridge/intel/e7501/debug.c +++ /dev/null @@ -1,175 +0,0 @@ -/* - * generic debug code, used by mainboard specific romstage.c - * - */ -#if 1 -static void print_debug_pci_dev(unsigned dev) -{ - printk(BIOS_DEBUG, "PCI: %02x:%02x.%x", - (dev >> 16) & 0xff, (dev >> 11) & 0x1f, (dev >> 8) & 7); -} - -static inline void print_pci_devices(void) -{ - device_t dev; - for (dev = PCI_DEV(0, 0, 0); - dev <= PCI_DEV(0xff, 0x1f, 0x7); - dev += PCI_DEV(0,0,1)) { - uint32_t id; - id = pci_read_config32(dev, PCI_VENDOR_ID); - if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) || - (((id >> 16) & 0xffff) == 0xffff) || - (((id >> 16) & 0xffff) == 0x0000)) { - continue; - } - print_debug_pci_dev(dev); - printk(BIOS_DEBUG, "\n"); - } -} - -static void dump_pci_device(unsigned dev) -{ - int i; - print_debug_pci_dev(dev); - - for (i = 0; i < 256; i++) { - unsigned char val; - if ((i & 0x0f) == 0) - printk(BIOS_DEBUG, "\n%02x:",i); - val = pci_read_config8(dev, i); - printk(BIOS_DEBUG, " %02x", val); - } - printk(BIOS_DEBUG, "\n"); -} - -static inline void dump_pci_devices(void) -{ - device_t dev; - for (dev = PCI_DEV(0, 0, 0); - dev <= PCI_DEV(0xff, 0x1f, 0x7); - dev += PCI_DEV(0,0,1)) { - uint32_t id; - id = pci_read_config32(dev, PCI_VENDOR_ID); - if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) || - (((id >> 16) & 0xffff) == 0xffff) || - (((id >> 16) & 0xffff) == 0x0000)) { - continue; - } - dump_pci_device(dev); - } -} - -static inline void dump_pci_devices_on_bus(unsigned busn) -{ - device_t dev; - for (dev = PCI_DEV(busn, 0, 0); - dev <= PCI_DEV(busn, 0x1f, 0x7); - dev += PCI_DEV(0,0,1)) { - uint32_t id; - id = pci_read_config32(dev, PCI_VENDOR_ID); - if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) || - (((id >> 16) & 0xffff) == 0xffff) || - (((id >> 16) & 0xffff) == 0x0000)) { - continue; - } - dump_pci_device(dev); - } -} - -static inline void dump_spd_registers(const struct mem_controller *ctrl) -{ - int i; - printk(BIOS_DEBUG, "\n"); - for (i = 0; i < 4; i++) { - unsigned device; - device = ctrl->channel0[i]; - if (device) { - int j; - printk(BIOS_DEBUG, "dimm: %02x.0: %02x", i, device); - for (j = 0; j < 128; j++) { - int status; - unsigned char byte; - if ((j & 0xf) == 0) - printk(BIOS_DEBUG, "\n%02x: ", j); - status = smbus_read_byte(device, j); - if (status < 0) { - break; - } - byte = status & 0xff; - printk(BIOS_DEBUG, "%02x ", byte); - } - printk(BIOS_DEBUG, "\n"); - } - device = ctrl->channel1[i]; - if (device) { - int j; - printk(BIOS_DEBUG, "dimm: %02x.1: %02x", i, device); - for (j = 0; j < 128; j++) { - int status; - unsigned char byte; - if ((j & 0xf) == 0) - printk(BIOS_DEBUG, "\n%02x: ", j); - status = smbus_read_byte(device, j); - if (status < 0) { - break; - } - byte = status & 0xff; - printk(BIOS_DEBUG, "%02x ", byte); - } - printk(BIOS_DEBUG, "\n"); - } - } -} -static inline void dump_smbus_registers(void) -{ - unsigned device; - printk(BIOS_DEBUG, "\n"); - for (device = 1; device < 0x80; device++) { - int j; - if ( smbus_read_byte(device, 0) < 0 ) continue; - printk(BIOS_DEBUG, "smbus: %02x", device); - for (j = 0; j < 256; j++) { - int status; - unsigned char byte; - status = smbus_read_byte(device, j); - if (status < 0) { - break; - } - if ((j & 0xf) == 0) - printk(BIOS_DEBUG, "\n%02x: ",j); - byte = status & 0xff; - printk(BIOS_DEBUG, "%02x ", byte); - } - printk(BIOS_DEBUG, "\n"); - } -} - -static inline void dump_io_resources(unsigned port) -{ - int i; - printk(BIOS_DEBUG, "%04x:\n", port); - for (i = 0; i < 256; i++) { - uint8_t val; - if ((i & 0x0f) == 0) - printk(BIOS_DEBUG, "%02x:", i); - val = inb(port); - printk(BIOS_DEBUG, " %02x",val); - if ((i & 0x0f) == 0x0f) { - printk(BIOS_DEBUG, "\n"); - } - port++; - } -} - -static inline void dump_mem(unsigned start, unsigned end) -{ - unsigned i; - printk(BIOS_DEBUG, "dump_mem:"); - for (i = start; i < end; i++) { - if ((i & 0xf)==0) - printk(BIOS_DEBUG, "\n%08x:", i); - printk(BIOS_DEBUG, " %02x", (unsigned char)*((unsigned char *)i)); - } - printk(BIOS_DEBUG, "\n"); -} -#endif diff --git a/src/northbridge/intel/e7501/e7501.h b/src/northbridge/intel/e7501/e7501.h deleted file mode 100644 index a2800fc896..0000000000 --- a/src/northbridge/intel/e7501/e7501.h +++ /dev/null @@ -1,80 +0,0 @@ -/* - * This file is part of the coreboot project. - * - * Copyright (C) 2005 Digital Design Corporation - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ - -/* - * e7501.h: PCI configuration space for the Intel E7501 memory controller - */ - -#ifndef NORTHBRIDGE_INTEL_E7501_E7501_H -#define NORTHBRIDGE_INTEL_E7501_E7501_H - -/************ D0:F0 ************/ -// Register offsets -#define MAYBE_SMRBASE 0x14 /* System Memory RCOMP Base Address Register, 32 bit? (if similar to 855PM) */ -#define MCHCFGNS 0x52 /* MCH (scrubber) configuration register, 16 bit */ -#define DRB_ROW_0 0x60 /* DRAM Row Boundary register, 8 bit */ -#define DRB_ROW_1 0x61 -#define DRB_ROW_2 0x62 -#define DRB_ROW_3 0x63 -#define DRB_ROW_4 0x64 -#define DRB_ROW_5 0x65 -#define DRB_ROW_6 0x66 -#define DRB_ROW_7 0x67 - -#define DRA 0x70 /* DRAM Row Attributes registers, 4 x 8 bit */ -#define DRT 0x78 /* DRAM Timing register, 32 bit */ -#define DRC 0x7C /* DRAM Controller Mode register, 32 bit */ -#define MAYBE_DRDCTL 0x80 /* DRAM Read Timing Control register, 16 bit? (if similar to 855PM) */ -#define CKDIS 0x8C /* Clock disable register, 8 bit */ -#define TOLM 0xC4 /* Top of Low Memory register, 16 bit */ -#define REMAPBASE 0xC6 /* Remap Base Address register, 16 bit */ -#define REMAPLIMIT 0xC8 /* Remap Limit Address register, 16 bit */ -#define SKPD 0xDE /* Scratchpad register, 16 bit */ -#define MAYBE_MCHTST 0xF4 /* MCH Test Register, 32 bit? (if similar to 855PM) */ - -// CAS# Latency bits in the DRAM Timing (DRT) register -#define DRT_CAS_2_5 (0<<4) -#define DRT_CAS_2_0 (1<<4) -#define DRT_CAS_MASK (3<<4) - -// Mode Select (SMS) bits in the DRAM Controller Mode (DRC) register -#define RAM_COMMAND_NOP (1<<4) -#define RAM_COMMAND_PRECHARGE (2<<4) -#define RAM_COMMAND_MRS (3<<4) -#define RAM_COMMAND_EMRS (4<<4) -#define RAM_COMMAND_CBR (6<<4) -#define RAM_COMMAND_NORMAL (7<<4) - - -// RCOMP Memory Map offsets -// Conjecture based on apparent similarity between E7501 and 855PM -// Intel doc. 252613-003 describes these for 855PM - -#define MAYBE_SMRCTL 0x20 /* System Memory RCOMP Control Register? */ -#define MAYBE_DQCMDSTR 0x30 /* Strength control for DQ and CMD signal groups? */ -#define MAYBE_CKESTR 0x31 /* Strength control for CKE signal group? */ -#define MAYBE_CSBSTR 0x32 /* Strength control for CS# signal group? */ -#define MAYBE_CKSTR 0x33 /* Strength control for CK signal group? */ -#define MAYBE_RCVENSTR 0x34 /* Strength control for RCVEnOut# signal group? */ - -/************ D0:F1 ************/ -// Register offsets -#define FERR_GLOBAL 0x40 /* First global error register, 32 bits */ -#define NERR_GLOBAL 0x44 /* Next global error register, 32 bits */ -#define DRAM_FERR 0x80 /* DRAM first error register, 8 bits */ -#define DRAM_NERR 0x82 /* DRAM next error register, 8 bits */ - -#endif /* NORTHBRIDGE_INTEL_E7501_E7501_H */ diff --git a/src/northbridge/intel/e7501/northbridge.c b/src/northbridge/intel/e7501/northbridge.c deleted file mode 100644 index d4f77ae654..0000000000 --- a/src/northbridge/intel/e7501/northbridge.c +++ /dev/null @@ -1,140 +0,0 @@ -#include <console/console.h> -#include <arch/io.h> -#include <stdint.h> -#include <device/device.h> -#include <device/pci.h> -#include <arch/acpi.h> -#include <cpu/cpu.h> -#include <stdlib.h> -#include <string.h> -#include <cbmem.h> - -#if IS_ENABLED(CONFIG_HAVE_ACPI_TABLES) - -unsigned long acpi_fill_mcfg(unsigned long current) -{ - /* Just a dummy */ - return current; -} - -#endif - - -static void pci_domain_set_resources(device_t dev) -{ - device_t mc_dev; - uint32_t pci_tolm; - - pci_tolm = find_pci_tolm(dev->link_list); - mc_dev = dev->link_list->children; - if (mc_dev) { - /* Figure out which areas are/should be occupied by RAM. - * This is all computed in kilobytes and converted to/from - * the memory controller right at the edges. - * Having different variables in different units is - * too confusing to get right. Kilobytes are good up to - * 4 Terabytes of RAM... - */ - uint16_t tolm_r, remapbase_r, remaplimit_r; - unsigned long tomk, tolmk; - unsigned long remapbasek, remaplimitk; - int idx; - - /* Get the value of the highest DRB. This tells the end of - * the physical memory. The units are ticks of 64MB - * i.e. 1 means 64MB. - */ - tomk = ((unsigned long)pci_read_config8(mc_dev, 0x67)) << 16; - /* Compute the top of Low memory */ - tolmk = pci_tolm >> 10; - if (tolmk >= tomk) { - /* The PCI hole does not overlap memory - * we won't use the remap window. - */ - tolmk = tomk; - remapbasek = 0x3ff << 16; - remaplimitk = 0 << 16; - } - else { - /* The PCI memory hole overlaps memory - * setup the remap window. - */ - /* Find the bottom of the remap window - * is it above 4G? - */ - remapbasek = 4*1024*1024; - if (tomk > remapbasek) { - remapbasek = tomk; - } - /* Find the limit of the remap window */ - remaplimitk = (remapbasek + (4*1024*1024 - tolmk) - (1 << 16)); - } - /* Write the RAM configuration registers, - * preserving the reserved bits. - */ - tolm_r = pci_read_config16(mc_dev, 0xc4); - tolm_r = ((tolmk >> 17) << 11) | (tolm_r & 0x7ff); - pci_write_config16(mc_dev, 0xc4, tolm_r); - - remapbase_r = pci_read_config16(mc_dev, 0xc6); - remapbase_r = (remapbasek >> 16) | (remapbase_r & 0xfc00); - pci_write_config16(mc_dev, 0xc6, remapbase_r); - - remaplimit_r = pci_read_config16(mc_dev, 0xc8); - remaplimit_r = (remaplimitk >> 16) | (remaplimit_r & 0xfc00); - pci_write_config16(mc_dev, 0xc8, remaplimit_r); - - /* Report the memory regions */ - idx = 10; - ram_resource(dev, idx++, 0, 640); - ram_resource(dev, idx++, 768, tolmk - 768); - if (tomk > 4*1024*1024) { - ram_resource(dev, idx++, 4096*1024, tomk - 4*1024*1024); - } - if (remaplimitk >= remapbasek) { - ram_resource(dev, idx++, remapbasek, - (remaplimitk + 64*1024) - remapbasek); - } - - set_top_of_ram(tolmk * 1024); - } - assign_resources(dev->link_list); -} - -static struct device_operations pci_domain_ops = { - .read_resources = pci_domain_read_resources, - .set_resources = pci_domain_set_resources, - .enable_resources = NULL, - .init = NULL, - .scan_bus = pci_domain_scan_bus, - .ops_pci_bus = pci_bus_default_ops, -}; - -static void cpu_bus_init(device_t dev) -{ - initialize_cpus(dev->link_list); -} - -static struct device_operations cpu_bus_ops = { - .read_resources = DEVICE_NOOP, - .set_resources = DEVICE_NOOP, - .enable_resources = DEVICE_NOOP, - .init = cpu_bus_init, - .scan_bus = 0, -}; - -static void enable_dev(struct device *dev) -{ - /* Set the operations if it is a special bus type */ - if (dev->path.type == DEVICE_PATH_DOMAIN) { - dev->ops = &pci_domain_ops; - } - else if (dev->path.type == DEVICE_PATH_CPU_CLUSTER) { - dev->ops = &cpu_bus_ops; - } -} - -struct chip_operations northbridge_intel_e7501_ops = { - CHIP_NAME("Intel E7501 Northbridge") - .enable_dev = enable_dev, -}; diff --git a/src/northbridge/intel/e7501/raminit.c b/src/northbridge/intel/e7501/raminit.c deleted file mode 100644 index 93a3a5b5a9..0000000000 --- a/src/northbridge/intel/e7501/raminit.c +++ /dev/null @@ -1,2009 +0,0 @@ -/* This was originally for the e7500, modified for e7501 - * The primary differences are that 7501 apparently can - * support single channel RAM (i haven't tested), - * CAS1.5 is no longer supported, The ECC scrubber - * now supports a mode to zero RAM and init ECC in one step - * and the undocumented registers at 0x80 require new - * (undocumented) values determined by guesswork and - * comparison w/ OEM BIOS values. - * Steven James 02/06/2003 - */ - -/* converted to C 6/2004 yhlu */ - -#include <assert.h> -#include <lib.h> -#include <spd.h> -#include <sdram_mode.h> -#include <stdlib.h> -#include "e7501.h" - -/*----------------------------------------------------------------------------- -Definitions: ------------------------------------------------------------------------------*/ - -// Uncomment this to enable run-time checking of DIMM parameters -// for dual-channel operation -// Unfortunately the code seems to chew up several K of space. -//#define VALIDATE_DIMM_COMPATIBILITY - -#if CONFIG_DEBUG_RAM_SETUP -#define RAM_DEBUG_MESSAGE(x) printk(BIOS_DEBUG, x) -#define RAM_DEBUG_HEX32(x) printk(BIOS_DEBUG, "%08x", x) -#define RAM_DEBUG_HEX8(x) printk(BIOS_DEBUG, "%02x", x) -#define DUMPNORTH() dump_pci_device(PCI_DEV(0, 0, 0)) -#else -#define RAM_DEBUG_MESSAGE(x) -#define RAM_DEBUG_HEX32(x) -#define RAM_DEBUG_HEX8(x) -#define DUMPNORTH() -#endif - -#define E7501_SDRAM_MODE (SDRAM_BURST_INTERLEAVED | SDRAM_BURST_4) -#define SPD_ERROR "Error reading SPD info\n" - -// NOTE: This used to be 0x100000. -// That doesn't work on systems where A20M# is asserted, because -// attempts to access 0x1000NN end up accessing 0x0000NN. -#define RCOMP_MMIO ((u8 *)0x200000) - -struct dimm_size { - unsigned long side1; - unsigned long side2; -}; - -static const uint32_t refresh_frequency[] = { - /* Relative frequency (array value) of each E7501 Refresh Mode Select - * (RMS) value (array index) - * 0 == least frequent refresh (longest interval between refreshes) - * [0] disabled -> 0 - * [1] 15.6 usec -> 2 - * [2] 7.8 usec -> 3 - * [3] 64 usec -> 1 - * [4] reserved -> 0 - * [5] reserved -> 0 - * [6] reserved -> 0 - * [7] 64 clocks -> 4 - */ - 0, 2, 3, 1, 0, 0, 0, 4 -}; - -static const uint32_t refresh_rate_map[] = { - /* Map the JEDEC spd refresh rates (array index) to E7501 Refresh Mode - * Select values (array value) - * These are all the rates defined by JESD21-C Appendix D, Rev. 1.0 - * The E7501 supports only 15.6 us (1), 7.8 us (2), 64 us (3), and - * 64 clock (481 ns) (7) refresh. - * [0] == 15.625 us -> 15.6 us - * [1] == 3.9 us -> 481 ns - * [2] == 7.8 us -> 7.8 us - * [3] == 31.3 us -> 15.6 us - * [4] == 62.5 us -> 15.6 us - * [5] == 125 us -> 64 us - */ - 1, 7, 2, 1, 1, 3 -}; - -#define MAX_SPD_REFRESH_RATE ((sizeof(refresh_rate_map) / sizeof(uint32_t)) - 1) - -// SPD parameters that must match for dual-channel operation -static const uint8_t dual_channel_parameters[] = { - SPD_MEMORY_TYPE, - SPD_MODULE_VOLTAGE, - SPD_NUM_COLUMNS, - SPD_NUM_ROWS, - SPD_NUM_DIMM_BANKS, - SPD_PRIMARY_SDRAM_WIDTH, - SPD_NUM_BANKS_PER_SDRAM -}; - - /* - * Table: constant_register_values - */ -static const long constant_register_values[] = { - /* SVID - Subsystem Vendor Identification Register - * 0x2c - 0x2d - * [15:00] Subsytem Vendor ID (Indicates system board vendor) - */ - /* SID - Subsystem Identification Register - * 0x2e - 0x2f - * [15:00] Subsystem ID - */ - // Not everyone wants to be Super Micro Computer, Inc. - // The mainboard should set this if desired. - // 0x2c, 0, (0x15d9 << 0) | (0x3580 << 16), - - /* Undocumented - * (DRAM Read Timing Control, if similar to 855PM?) - * 0x80 - 0x81 - * This register has something to do with CAS latencies, - * possibily this is the real chipset control. - * At 0x00 CAS latency 1.5 works. - * At 0x06 CAS latency 2.5 works. - * At 0x01 CAS latency 2.0 works. - */ - /* This is still undocumented in e7501, but with different values - * CAS 2.0 values taken from Intel BIOS settings, others are a guess - * and may be terribly wrong. Old values preserved as comments until I - * figure this out for sure. - * e7501 docs claim that CAS1.5 is unsupported, so it may or may not - * work at all. - * Steven James 02/06/2003 - */ - /* NOTE: values now configured in configure_e7501_cas_latency() based - * on SPD info and total number of DIMMs (per Intel) - */ - - /* FDHC - Fixed DRAM Hole Control - * 0x58 - * [7:7] Hole_Enable - * 0 == No memory Hole - * 1 == Memory Hole from 15MB to 16MB - * [6:0] Reserved - * - * PAM - Programmable Attribute Map - * 0x59 [1:0] Reserved - * 0x59 [5:4] 0xF0000 - 0xFFFFF - * 0x5A [1:0] 0xC0000 - 0xC3FFF - * 0x5A [5:4] 0xC4000 - 0xC7FFF - * 0x5B [1:0] 0xC8000 - 0xCBFFF - * 0x5B [5:4] 0xCC000 - 0xCFFFF - * 0x5C [1:0] 0xD0000 - 0xD3FFF - * 0x5C [5:4] 0xD4000 - 0xD7FFF - * 0x5D [1:0] 0xD8000 - 0xDBFFF - * 0x5D [5:4] 0xDC000 - 0xDFFFF - * 0x5E [1:0] 0xE0000 - 0xE3FFF - * 0x5E [5:4] 0xE4000 - 0xE7FFF - * 0x5F [1:0] 0xE8000 - 0xEBFFF - * 0x5F [5:4] 0xEC000 - 0xEFFFF - * 00 == DRAM Disabled (All Access go to memory mapped I/O space) - * 01 == Read Only (Reads to DRAM, Writes to memory mapped I/O space) - * 10 == Write Only (Writes to DRAM, Reads to memory mapped I/O space) - * 11 == Normal (All Access go to DRAM) - */ - - // Map all legacy ranges to DRAM - 0x58, 0xcccccf7f, (0x00 << 0) | (0x30 << 8) | (0x33 << 16) | (0x33 << 24), - 0x5C, 0xcccccccc, (0x33 << 0) | (0x33 << 8) | (0x33 << 16) | (0x33 << 24), - - /* DRB - DRAM Row Boundary Registers - * 0x60 - 0x6F - * An array of 8 byte registers, which hold the ending - * memory address assigned to each pair of DIMMS, in 64MB - * granularity. - */ - // Conservatively say each row has 64MB of ram, we will fix this up later - // NOTE: These defaults allow us to prime all of the DIMMs on the board - // without jumping through 36-bit adddressing hoops, even if the - // total memory is > 4 GB. Changing these values may break do_ram_command()! - 0x60, 0x00000000, (0x01 << 0) | (0x02 << 8) | (0x03 << 16) | (0x04 << 24), - 0x64, 0x00000000, (0x05 << 0) | (0x06 << 8) | (0x07 << 16) | (0x08 << 24), - - /* DRA - DRAM Row Attribute Register - * 0x70 Row 0,1 - * 0x71 Row 2,3 - * 0x72 Row 4,5 - * 0x73 Row 6,7 - * [7:7] Device width for Odd numbered rows - * 0 == 8 bits wide x8 - * 1 == 4 bits wide x4 - * [6:4] Row Attributes for Odd numbered rows - * 010 == 8KB (for dual-channel) - * 011 == 16KB (for dual-channel) - * 100 == 32KB (for dual-channel) - * 101 == 64KB (for dual-channel) - * Others == Reserved - * [3:3] Device width for Even numbered rows - * 0 == 8 bits wide x8 - * 1 == 4 bits wide x4 - * [2:0] Row Attributes for Even numbered rows - * 010 == 8KB (for dual-channel) - * 011 == 16KB (for dual-channel) - * 100 == 32KB (for dual-channel) - * 101 == 64KB (This page size appears broken) - * Others == Reserved - */ - // NOTE: overridden by configure_e7501_row_attributes(), later - 0x70, 0x00000000, 0, - - /* DRT - DRAM Timing Register - * 0x78 - * [31:30] Reserved - * [29:29] Back to Back Write-Read Turn Around - * 0 == 3 clocks between WR-RD commands - * 1 == 2 clocks between WR-RD commands - * [28:28] Back to Back Read-Write Turn Around - * 0 == 5 clocks between RD-WR commands - * 1 == 4 clocks between RD-WR commands - * [27:27] Back to Back Read Turn Around - * 0 == 4 clocks between RD commands - * 1 == 3 clocks between RD commands - * [26:24] Read Delay (tRD) - * 000 == 7 clocks - * 001 == 6 clocks - * 010 == 5 clocks - * Others == Reserved - * [23:19] Reserved - * [18:16] DRAM idle timer - * 000 == infinite - * 011 == 16 dram clocks - * 001 == 0 clocks - * [15:11] Reserved - * [10:09] Active to Precharge (tRAS) - * 00 == 7 clocks - * 01 == 6 clocks - * 10 == 5 clocks - * 11 == Reserved - * [08:06] Reserved - * [05:04] Cas Latency (tCL) - * 00 == 2.5 Clocks - * 01 == 2.0 Clocks - * 10 == Reserved (was 1.5 Clocks for E7500) - * 11 == Reserved - * [03:03] Write Ras# to Cas# Delay (tRCD) - * 0 == 3 DRAM Clocks - * 1 == 2 DRAM Clocks - * [02:01] Read RAS# to CAS# Delay (tRCD) - * 00 == reserved - * 01 == reserved - * 10 == 3 DRAM Clocks - * 11 == 2 DRAM Clocks - * [00:00] DRAM RAS# to Precharge (tRP) - * 0 == 3 DRAM Clocks - * 1 == 2 DRAM Clocks - */ - - // Some earlier settings: - /* Most aggressive settings possible */ -// 0x78, 0xc0fff8c4, (1<<29)|(1<<28)|(1<<27)|(2<<24)|(2<<9)|CAS_LATENCY|(1<<3)|(1<<1)|(1<<0), -// 0x78, 0xc0f8f8c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|CAS_LATENCY|(1<<3)|(3<<1)|(1<<0), -// 0x78, 0xc0f8f9c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|CAS_LATENCY|(1<<3)|(3<<1)|(1<<0), - - // The only things we need to set here are DRAM idle timer, Back-to-Back Read Turnaround, and - // Back-to-Back Write-Read Turnaround. All others are configured based on SPD. - 0x78, 0xD7F8FFFF, (1 << 29) | (1 << 27) | (1 << 16), - - /* FIXME why was I attempting to set a reserved bit? */ - /* 0x0100040f */ - - /* DRC - DRAM Contoller Mode Register - * 0x7c - * [31:30] Reserved - * [29:29] Initialization Complete - * 0 == Not Complete - * 1 == Complete - * [28:23] Reserved - * [22:22] Channels - * 0 == Single channel - * 1 == Dual Channel - * [21:20] DRAM Data Integrity Mode - * 00 == Disabled, no ECC - * 01 == Reserved - * 10 == Error checking, using chip-kill, with correction - * 11 == Reserved - * [19:18] DRB Granularity (Read-Only) - * 00 == 32 MB quantities (single channel mode) - * 01 == 64 MB quantities (dual-channel mode) - * 10 == Reserved - * 11 == Reserved - * [17:17] (Intel Undocumented) should always be set to 1 (SJM: comment inconsistent with current setting, below) - * [16:16] Command Per Clock - Address/Control Assertion Rule (CPC) - * 0 == 2n Rule - * 1 == 1n rule - * [15:11] Reserved - * [10:08] Refresh mode select - * 000 == Refresh disabled - * 001 == Refresh interval 15.6 usec - * 010 == Refresh interval 7.8 usec - * 011 == Refresh interval 64 usec - * 111 == Refresh every 64 clocks (fast refresh) - * [07:07] Reserved - * [06:04] Mode Select (SMS) - * 000 == Reserved (was Self Refresh Mode in E7500) - * 001 == NOP Command - * 010 == All Banks Precharge - * 011 == Mode Register Set - * 100 == Extended Mode Register Set - * 101 == Reserved - * 110 == CBR Refresh - * 111 == Normal Operation - * [03:00] Reserved - */ -// .long 0x7c, 0xffcefcff, (1<<22)|(2 << 20)|(1 << 16)| (0 << 8), -// .long 0x7c, 0xff8cfcff, (1<<22)|(2 << 20)|(1 << 17)|(1 << 16)| (0 << 8), -// .long 0x7c, 0xff80fcff, (1<<22)|(2 << 20)|(1 << 18)|(1 << 17)|(1 << 16)| (0 << 8), - - // Default to dual-channel mode, ECC, 1-clock address/cmd hold - // NOTE: configure_e7501_dram_controller_mode() configures further - 0x7c, 0xff8ef8ff, (1 << 22) | (2 << 20) | (1 << 16) | (0 << 8), - - /* Another Intel undocumented register - * 0x88 - 0x8B - * [31:31] Purpose unknown - * [26:26] Master DLL Reset? - * 0 == Normal operation? - * 1 == Reset? - * [07:07] Periodic memory recalibration? - * 0 == Disabled? - * 1 == Enabled? - * [04:04] Receive FIFO RE-Sync? - * 0 == Normal operation? - * 1 == Reset? - */ - // NOTE: Some factory BIOSs don't do this. - // Doesn't seem to matter either way. - 0x88, 0xffffff00, 0x80, - - /* CLOCK_DIS - CK/CK# Disable Register - * 0x8C - * [7:7] DDR Frequency - * 0 == 100 MHz (200 MHz data rate) - * 1 == 133 MHz (266 MHz data rate) - * [6:4] Reserved - * [3:3] CK3 - * 0 == Enable - * 1 == Disable - * [2:2] CK2 - * 0 == Enable - * 1 == Disable - * [1:1] CK1 - * 0 == Enable - * 1 == Disable - * [0:0] CK0 - * 0 == Enable - * 1 == Disable - */ - // NOTE: Disable all clocks initially; turn ones we need back on - // in enable_e7501_clocks() - 0x8C, 0xfffffff0, 0xf, - - /* TOLM - Top of Low Memory Register - * 0xC4 - 0xC5 - * [15:11] Top of low memory (TOLM) - * The address below 4GB that should be treated as RAM, - * on a 128MB granularity. - * [10:00] Reserved - */ - /* REMAPBASE - Remap Base Address Regsiter - * 0xC6 - 0xC7 - * [15:10] Reserved - * [09:00] Remap Base Address [35:26] 64M aligned - * Bits [25:0] are assumed to be 0. - */ - - // NOTE: TOLM overridden by configure_e7501_ram_addresses() - 0xc4, 0xfc0007ff, (0x2000 << 0) | (0x3ff << 16), - - /* REMAPLIMIT - Remap Limit Address Register - * 0xC8 - 0xC9 - * [15:10] Reserved - * [09:00] Remap Limit Address [35:26] 64M aligned - * When remaplimit < remapbase the remap window is disabled. - */ - 0xc8, 0xfffffc00, 0, - - /* DVNP - Device Not Present Register - * 0xE0 - 0xE1 - * [15:05] Reserved - * [04:04] Device 4 Function 1 Present - * 0 == Present - * 1 == Absent - * [03:03] Device 3 Function 1 Present - * 0 == Present - * 1 == Absent - * [02:02] Device 2 Function 1 Present - * 0 == Present - * 1 == Absent - * [01:01] Reserved - * [00:00] Device 0 Function 1 Present - * 0 == Present - * 1 == Absent - */ - - // Enable D0:D1, disable D2:F1, D3:F1, D4:F1 - 0xe0, 0xffffffe2, (1 << 4) | (1 << 3) | (1 << 2) | (0 << 0), - - // Undocumented - 0xd8, 0xffff9fff, 0x00000000, - - // Undocumented - this is pure conjecture based on similarity to 855PM - /* MCHTST - MCH Test Register - * 0xF4 - 0xF7 - * [31:31] Purpose unknown - * [30:30] Purpose unknown - * [29:23] Unknown - not used? - * [22:22] System Memory MMR Enable - * 0 == Disable: mem space and BAR at 0x14 are not accessible - * 1 == Enable: mem space and BAR at 0x14 are accessible - * [21:20] Purpose unknown - * [19:02] Unknown - not used? - * [01:01] D6EN (Device #6 enable) - * 0 == Disable - * 1 == Enable - * [00:00] Unknown - not used? - */ - - 0xf4, 0x3f8ffffd, 0x40300002, - -#ifdef SUSPICIOUS_LOOKING_CODE - // SJM: Undocumented. - // This will access D2:F0:0x50, is this correct?? - 0x1050, 0xffffffcf, 0x00000030, -#endif -}; - - /* DDR RECOMP tables */ - -// Slew table for 1x drive? -static const uint32_t maybe_1x_slew_table[] = { - 0x44332211, 0xc9776655, 0xffffffff, 0xffffffff, - 0x22111111, 0x55444332, 0xfffca876, 0xffffffff, -}; - -// Slew table for 2x drive? -static const uint32_t maybe_2x_slew_table[] = { - 0x00000000, 0x76543210, 0xffffeca8, 0xffffffff, - 0x21000000, 0xa8765432, 0xffffffec, 0xffffffff, -}; - -// Pull Up / Pull Down offset table, if analogous to IXP2800? -static const uint32_t maybe_pull_updown_offset_table[] = { - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - 0x88888888, 0x88888888, 0x88888888, 0x88888888, -}; - -/*----------------------------------------------------------------------------- -Delay functions: ------------------------------------------------------------------------------*/ - -#define SLOW_DOWN_IO inb(0x80) -//#define SLOW_DOWN_IO udelay(40); - - /* Estimate that SLOW_DOWN_IO takes about 50&76us */ - /* delay for 200us */ - -#if 1 -static void do_delay(void) -{ - int i; - for (i = 0; i < 16; i++) { - SLOW_DOWN_IO; - } -} - -#define DO_DELAY do_delay() -#else -#define DO_DELAY \ - udelay(200) -#endif - -#define EXTRA_DELAY DO_DELAY - -static void die_on_spd_error(int spd_return_value) -{ - if (spd_return_value < 0) - die("Error reading SPD info\n"); -} - -/*----------------------------------------------------------------------------- -Serial presence detect (SPD) functions: ------------------------------------------------------------------------------*/ - -/** - * Calculate the page size for each physical bank of the DIMM: - * log2(page size) = (# columns) + log2(data width) - * - * NOTE: Page size is the total number of data bits in a row. - * - * @param dimm_socket_address SMBus address of DIMM socket to interrogate. - * @return log2(page size) for each side of the DIMM. - */ -static struct dimm_size sdram_spd_get_page_size(uint16_t dimm_socket_address) -{ - uint16_t module_data_width; - int value; - struct dimm_size pgsz; - - pgsz.side1 = 0; - pgsz.side2 = 0; - - // Side 1 - value = spd_read_byte(dimm_socket_address, SPD_NUM_COLUMNS); - if (value < 0) - goto hw_err; - pgsz.side1 = value & 0xf; // # columns in bank 1 - - /* Get the module data width and convert it to a power of two */ - value = - spd_read_byte(dimm_socket_address, SPD_MODULE_DATA_WIDTH_MSB); - if (value < 0) - goto hw_err; - module_data_width = (value & 0xff) << 8; - - value = - spd_read_byte(dimm_socket_address, SPD_MODULE_DATA_WIDTH_LSB); - if (value < 0) - goto hw_err; - module_data_width |= (value & 0xff); - - pgsz.side1 += log2(module_data_width); - - /* side two */ - value = spd_read_byte(dimm_socket_address, SPD_NUM_DIMM_BANKS); - if (value < 0) - goto hw_err; - if (value > 2) - die("Bad SPD value\n"); - if (value == 2) { - - pgsz.side2 = pgsz.side1; // Assume symmetric banks until we know differently - value = - spd_read_byte(dimm_socket_address, SPD_NUM_COLUMNS); - if (value < 0) - goto hw_err; - if ((value & 0xf0) != 0) { - // Asymmetric banks - pgsz.side2 -= value & 0xf; /* Subtract out columns on side 1 */ - pgsz.side2 += (value >> 4) & 0xf; /* Add in columns on side 2 */ - } - } - - return pgsz; - - hw_err: - die(SPD_ERROR); - return pgsz; // Never reached -} - -/** - * Read the width in bits of each DIMM side's DRAMs via SPD (i.e. 4, 8, 16). - * - * @param dimm_socket_address SMBus address of DIMM socket to interrogate. - * @return Width in bits of each DIMM side's DRAMs. - */ -static struct dimm_size sdram_spd_get_width(uint16_t dimm_socket_address) -{ - int value; - struct dimm_size width; - - width.side1 = 0; - width.side2 = 0; - - value = - spd_read_byte(dimm_socket_address, SPD_PRIMARY_SDRAM_WIDTH); - die_on_spd_error(value); - - width.side1 = value & 0x7f; // Mask off bank 2 flag - - if (value & 0x80) { - width.side2 = width.side1 << 1; // Bank 2 exists and is double-width - } else { - // If bank 2 exists, it's the same width as bank 1 - value = - spd_read_byte(dimm_socket_address, SPD_NUM_DIMM_BANKS); - die_on_spd_error(value); - -#ifdef ROMCC_IF_BUG_FIXED - if (value == 2) - width.side2 = width.side1; -#else - switch (value) { - case 2: - width.side2 = width.side1; - break; - - default: - break; - } -#endif - } - - return width; -} - -/** - * Calculate the log base 2 size in bits of both DIMM sides. - * - * log2(# bits) = (# columns) + log2(data width) + - * (# rows) + log2(banks per SDRAM) - * - * Note that it might be easier to use SPD byte 31 here, it has the DIMM size - * as a multiple of 4MB. The way we do it now we can size both sides of an - * asymmetric DIMM. - * - * @param dimm_socket_address SMBus address of DIMM socket to interrogate. - * @return log2(number of bits) for each side of the DIMM. - */ -static struct dimm_size spd_get_dimm_size(unsigned dimm_socket_address) -{ - int value; - - // Start with log2(page size) - struct dimm_size sz = sdram_spd_get_page_size(dimm_socket_address); - - if (sz.side1 > 0) { - - value = spd_read_byte(dimm_socket_address, SPD_NUM_ROWS); - die_on_spd_error(value); - - sz.side1 += value & 0xf; - - if (sz.side2 > 0) { - - // Double-sided DIMM - if (value & 0xF0) - sz.side2 += value >> 4; // Asymmetric - else - sz.side2 += value; // Symmetric - } - - value = - spd_read_byte(dimm_socket_address, - SPD_NUM_BANKS_PER_SDRAM); - die_on_spd_error(value); - - value = log2(value); - sz.side1 += value; - if (sz.side2 > 0) - sz.side2 += value; - } - - return sz; -} - -#ifdef VALIDATE_DIMM_COMPATIBILITY - -/** - * Determine whether two DIMMs have the same value for an SPD parameter. - * - * @param spd_byte_number The SPD byte number to compare in both DIMMs. - * @param dimm0_address SMBus address of the 1st DIMM socket to interrogate. - * @param dimm1_address SMBus address of the 2nd DIMM socket to interrogate. - * @return 1 if both DIMM sockets report the same value for the specified - * SPD parameter, 0 if the values differed or an error occurred. - */ -static uint8_t are_spd_values_equal(uint8_t spd_byte_number, - uint16_t dimm0_address, - uint16_t dimm1_address) -{ - uint8_t bEqual = 0; - int dimm0_value = spd_read_byte(dimm0_address, spd_byte_number); - int dimm1_value = spd_read_byte(dimm1_address, spd_byte_number); - - if ((dimm0_value >= 0) && (dimm1_value >= 0) - && (dimm0_value == dimm1_value)) - bEqual = 1; - - return bEqual; -} -#endif - -/** - * Scan for compatible DIMMs. - * - * The code in this module only supports dual-channel operation, so we test - * that compatible DIMMs are paired. - * - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - * @return A bitmask indicating which of the possible sockets for each channel - * was found to contain a compatible DIMM. - * Bit 0 corresponds to the closest socket for channel 0 - * Bit 1 to the next socket for channel 0 - * ... - * Bit MAX_DIMM_SOCKETS_PER_CHANNEL-1 to the last socket for channel 0 - * Bit MAX_DIMM_SOCKETS_PER_CHANNEL is the closest socket for channel 1 - * ... - * Bit 2*MAX_DIMM_SOCKETS_PER_CHANNEL-1 is the last socket for channel 1 - */ -static uint8_t spd_get_supported_dimms(const struct mem_controller *ctrl) -{ - int i; - uint8_t dimm_mask = 0; - - // Have to increase size of dimm_mask if this assertion is violated - ASSERT(MAX_DIMM_SOCKETS_PER_CHANNEL <= 4); - - // Find DIMMs we can support on channel 0. - // Then see if the corresponding channel 1 DIMM has the same parameters, - // since we only support dual-channel. - - for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { - - uint16_t channel0_dimm = ctrl->channel0[i]; - uint16_t channel1_dimm = ctrl->channel1[i]; - uint8_t bDualChannel = 1; -#ifdef VALIDATE_DIMM_COMPATIBILITY - struct dimm_size page_size; - struct dimm_size sdram_width; -#endif - int spd_value; - - if (channel0_dimm == 0) - continue; // No such socket on this mainboard - - if (spd_read_byte(channel0_dimm, SPD_MEMORY_TYPE) != - SPD_MEMORY_TYPE_SDRAM_DDR) - continue; - -#ifdef VALIDATE_DIMM_COMPATIBILITY - if (spd_read_byte(channel0_dimm, SPD_MODULE_VOLTAGE) != - SPD_VOLTAGE_SSTL2) - continue; // Unsupported voltage - - // E7501 does not support unregistered DIMMs - spd_value = - spd_read_byte(channel0_dimm, SPD_MODULE_ATTRIBUTES); - if (!(spd_value & MODULE_REGISTERED) || (spd_value < 0)) - continue; - - // Must support burst = 4 for dual-channel operation on E7501 - // NOTE: for single-channel, burst = 8 is required - spd_value = - spd_read_byte(channel0_dimm, - SPD_SUPPORTED_BURST_LENGTHS); - if (!(spd_value & SPD_BURST_LENGTH_4) || (spd_value < 0)) - continue; - - page_size = sdram_spd_get_page_size(channel0_dimm); - sdram_width = sdram_spd_get_width(channel0_dimm); - - // Validate DIMM page size - // The E7501 only supports page sizes of 4, 8, 16, or 32 KB per channel - // NOTE: 4 KB = 32 Kb = 2^15 - // 32 KB = 262 Kb = 2^18 - - if ((page_size.side1 < 15) || (page_size.side1 > 18)) - continue; - - // If DIMM is double-sided, verify side2 page size - if (page_size.side2 != 0) { - if ((page_size.side2 < 15) - || (page_size.side2 > 18)) - continue; - } - // Validate SDRAM width - // The E7501 only supports x4 and x8 devices - - if ((sdram_width.side1 != 4) && (sdram_width.side1 != 8)) - continue; - - // If DIMM is double-sided, verify side2 width - if (sdram_width.side2 != 0) { - if ((sdram_width.side2 != 4) - && (sdram_width.side2 != 8)) - continue; - } -#endif - // Channel 0 DIMM looks compatible. - // Now see if it is paired with the proper DIMM on channel 1. - - ASSERT(channel1_dimm != 0); // No such socket on this mainboard?? - - // NOTE: unpopulated DIMMs cause read to fail - spd_value = - spd_read_byte(channel1_dimm, SPD_MODULE_ATTRIBUTES); - if (!(spd_value & MODULE_REGISTERED) || (spd_value < 0)) { - - printk(BIOS_DEBUG, "Skipping un-matched DIMMs - only dual-channel operation supported\n"); - continue; - } -#ifdef VALIDATE_DIMM_COMPATIBILITY - spd_value = - spd_read_byte(channel1_dimm, - SPD_SUPPORTED_BURST_LENGTHS); - if (!(spd_value & SPD_BURST_LENGTH_4) || (spd_value < 0)) - continue; - - int j; - for (j = 0; j < sizeof(dual_channel_parameters); ++j) { - if (!are_spd_values_equal - (dual_channel_parameters[j], channel0_dimm, - channel1_dimm)) { - - bDualChannel = 0; - break; - } - } -#endif - - // Code around ROMCC bug in optimization of "if" statements -#ifdef ROMCC_IF_BUG_FIXED - if (bDualChannel) { - // Made it through all the checks, this DIMM pair is usable - dimm_mask |= ((1 << i) | (1 << (MAX_DIMM_SOCKETS_PER_CHANNEL + i))); - } else - printk(BIOS_DEBUG, "Skipping un-matched DIMMs - only dual-channel operation supported\n"); -#else - switch (bDualChannel) { - case 0: - printk(BIOS_DEBUG, "Skipping un-matched DIMMs - only dual-channel operation supported\n"); - break; - - default: - // Made it through all the checks, this DIMM pair is usable - dimm_mask |= (1 << i) | (1 << (MAX_DIMM_SOCKETS_PER_CHANNEL + i)); - break; - } -#endif - } - - return dimm_mask; -} - -/*----------------------------------------------------------------------------- -SDRAM configuration functions: ------------------------------------------------------------------------------*/ - -/** - * Send the specified command to all DIMMs. - * - * @param command Specifies the command to be sent to the DIMMs. - * @param jedec_mode_bits For the MRS & EMRS commands, bits 0-12 contain the - * register value in JEDEC format. - */ -static void do_ram_command(uint8_t command, uint16_t jedec_mode_bits) -{ - int i; - uint32_t dram_controller_mode; - uint8_t dimm_start_64M_multiple = 0; - uint16_t e7501_mode_bits = jedec_mode_bits; - - // Configure the RAM command - dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); - dram_controller_mode &= 0xFFFFFF8F; - dram_controller_mode |= command; - pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); - - // RAM_COMMAND_NORMAL is an exception. - // It affects only the memory controller and does not need to be "sent" to the DIMMs. - - if (command != RAM_COMMAND_NORMAL) { - - // Send the command to all DIMMs by accessing a memory location within each - // NOTE: for mode select commands, some of the location address bits - // are part of the command - - // Map JEDEC mode bits to E7501 - if (command == RAM_COMMAND_MRS) { - // Host address lines [15:5] map to DIMM address lines [12:11, 9:1] - // The E7501 hard-sets DIMM address lines 10 & 0 to zero - - ASSERT(!(jedec_mode_bits & 0x0401)); - - e7501_mode_bits = ((jedec_mode_bits & 0x1800) << (15 - 12)) | // JEDEC bits 11-12 move to bits 14-15 - ((jedec_mode_bits & 0x03FE) << (13 - 9)); // JEDEC bits 1-9 move to bits 5-13 - - } else if (command == RAM_COMMAND_EMRS) { - // Host address lines [15:3] map to DIMM address lines [12:0] - e7501_mode_bits = jedec_mode_bits <<= 3; - } else - ASSERT(jedec_mode_bits == 0); - - dimm_start_64M_multiple = 0; - - for (i = 0; i < (MAX_NUM_CHANNELS * MAX_DIMM_SOCKETS_PER_CHANNEL); ++i) { - - uint8_t dimm_end_64M_multiple = - pci_read_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + i); - if (dimm_end_64M_multiple > dimm_start_64M_multiple) { - - // This code assumes DRAM row boundaries are all set below 4 GB - // NOTE: 0x40 * 64 MB == 4 GB - ASSERT(dimm_start_64M_multiple < 0x40); - - // NOTE: 2^26 == 64 MB - - u8 *dimm_start_address = (u8 *) - (dimm_start_64M_multiple << 26); - - RAM_DEBUG_MESSAGE(" Sending RAM command to 0x"); - RAM_DEBUG_HEX32(dimm_start_address + e7501_mode_bits); - RAM_DEBUG_MESSAGE("\n"); - - read32(dimm_start_address + e7501_mode_bits); - - // Set the start of the next DIMM - dimm_start_64M_multiple = - dimm_end_64M_multiple; - } - } - } -} - -/** - * Set the mode register of all DIMMs. - * - * The proper CAS# latency setting is added to the mode bits specified - * by the caller. - * - * @param jedec_mode_bits For the MRS & EMRS commands, bits 0-12 contain the - * register value in JEDEC format. - */ -static void set_ram_mode(uint16_t jedec_mode_bits) -{ - ASSERT(!(jedec_mode_bits & SDRAM_CAS_MASK)); - - uint32_t dram_cas_latency = - pci_read_config32(PCI_DEV(0, 0, 0), DRT) & DRT_CAS_MASK; - - switch (dram_cas_latency) { - case DRT_CAS_2_5: - jedec_mode_bits |= SDRAM_CAS_2_5; - break; - - case DRT_CAS_2_0: - jedec_mode_bits |= SDRAM_CAS_2_0; - break; - - default: - BUG(); - break; - } - - do_ram_command(RAM_COMMAND_MRS, jedec_mode_bits); -} - -/*----------------------------------------------------------------------------- -DIMM-independant configuration functions: ------------------------------------------------------------------------------*/ - -/** - * Configure the E7501's DRAM Row Boundary (DRB) registers for the memory - * present in the specified DIMM. - * - * @param dimm_log2_num_bits Specifies log2(number of bits) for each side of - * the DIMM. - * @param total_dram_64M_multiple Total DRAM in the system (as a multiple of - * 64 MB) for DIMMs < dimm_index. - * @param dimm_index Which DIMM pair is being processed - * (0..MAX_DIMM_SOCKETS_PER_CHANNEL). - * @return New multiple of 64 MB total DRAM in the system. - */ -static uint8_t configure_dimm_row_boundaries(struct dimm_size dimm_log2_num_bits, uint8_t total_dram_64M_multiple, unsigned dimm_index) -{ - int i; - - ASSERT(dimm_index < MAX_DIMM_SOCKETS_PER_CHANNEL); - - // DIMM sides must be at least 32 MB - ASSERT(dimm_log2_num_bits.side1 >= 28); - ASSERT((dimm_log2_num_bits.side2 == 0) - || (dimm_log2_num_bits.side2 >= 28)); - - // In dual-channel mode, we are called only once for each pair of DIMMs. - // Each time we process twice the capacity of a single DIMM. - - // Convert single DIMM capacity to paired DIMM capacity - // (multiply by two ==> add 1 to log2) - dimm_log2_num_bits.side1++; - if (dimm_log2_num_bits.side2 > 0) - dimm_log2_num_bits.side2++; - - // Add the capacity of side 1 this DIMM pair (as a multiple of 64 MB) - // to the total capacity of the system - // NOTE: 64 MB == 512 Mb, and log2(512 Mb) == 29 - - total_dram_64M_multiple += (1 << (dimm_log2_num_bits.side1 - 29)); - - // Configure the boundary address for the row on side 1 - pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + (dimm_index << 1), - total_dram_64M_multiple); - - // If the DIMMs are double-sided, add the capacity of side 2 this DIMM pair - // (as a multiple of 64 MB) to the total capacity of the system - if (dimm_log2_num_bits.side2 >= 29) - total_dram_64M_multiple += - (1 << (dimm_log2_num_bits.side2 - 29)); - - // Configure the boundary address for the row (if any) on side 2 - pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_1 + (dimm_index << 1), - total_dram_64M_multiple); - - // Update boundaries for rows subsequent to these. - // These settings will be overridden by a subsequent call if a populated physical slot exists - - for (i = dimm_index + 1; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { - pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + (i << 1), - total_dram_64M_multiple); - pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_1 + (i << 1), - total_dram_64M_multiple); - } - - return total_dram_64M_multiple; -} - -/** - * Set the E7501's DRAM row boundary addresses & its Top Of Low Memory (TOLM). - * - * If necessary, set up a remap window so we don't waste DRAM that ordinarily - * would lie behind addresses reserved for memory-mapped I/O. - * - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms(). - */ -static void configure_e7501_ram_addresses(const struct mem_controller - *ctrl, uint8_t dimm_mask) -{ - int i; - uint8_t total_dram_64M_multiple = 0; - - // Configure the E7501's DRAM row boundaries - // Start by zeroing out the temporary initial configuration - pci_write_config32(PCI_DEV(0, 0, 0), DRB_ROW_0, 0); - pci_write_config32(PCI_DEV(0, 0, 0), DRB_ROW_4, 0); - - for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { - - uint16_t dimm_socket_address = ctrl->channel0[i]; - struct dimm_size sz; - - if (!(dimm_mask & (1 << i))) - continue; // This DIMM not present - - sz = spd_get_dimm_size(dimm_socket_address); - - RAM_DEBUG_MESSAGE("dimm size ="); - RAM_DEBUG_HEX32((u32)sz.side1); - RAM_DEBUG_MESSAGE(" "); - RAM_DEBUG_HEX32((u32)sz.side2); - RAM_DEBUG_MESSAGE("\n"); - - if (sz.side1 == 0) - die("Bad SPD value\n"); - - total_dram_64M_multiple = - configure_dimm_row_boundaries(sz, total_dram_64M_multiple, i); - } - - // Configure the Top Of Low Memory (TOLM) in the E7501 - // This address must be a multiple of 128 MB that is less than 4 GB. - // NOTE: 16-bit wide TOLM register stores only the highest 5 bits of a 32-bit address - // in the highest 5 bits. - - // We set TOLM to the smaller of 0xC0000000 (3 GB) or the total DRAM in the system. - // This reserves addresses from 0xC0000000 - 0xFFFFFFFF for non-DRAM purposes - // such as flash and memory-mapped I/O. - - // If there is more than 3 GB of DRAM, we define a remap window which - // makes the DRAM "behind" the reserved region available above the top of physical - // memory. - - // NOTE: 0xC0000000 / (64 MB) == 0x30 - - if (total_dram_64M_multiple <= 0x30) { - - // <= 3 GB total RAM - - /* I should really adjust all of this in C after I have resources - * to all of the pci devices. - */ - - // Round up to 128MB granularity - // SJM: Is "missing" 64 MB of memory a potential issue? Should this round down? - - uint8_t total_dram_128M_multiple = - (total_dram_64M_multiple + 1) >> 1; - - // Convert to high 16 bits of address - uint16_t top_of_low_memory = - total_dram_128M_multiple << 11; - - pci_write_config16(PCI_DEV(0, 0, 0), TOLM, - top_of_low_memory); - - } else { - - // > 3 GB total RAM - - // Set defaults for > 4 GB DRAM, i.e. remap a 1 GB (= 0x10 * 64 MB) range of memory - uint16_t remap_base = total_dram_64M_multiple; // A[25:0] == 0 - uint16_t remap_limit = total_dram_64M_multiple + 0x10 - 1; // A[25:0] == 0xF - - // Put TOLM at 3 GB - - pci_write_config16(PCI_DEV(0, 0, 0), TOLM, 0xc000); - - // Define a remap window to make the RAM that would appear from 3 GB - 4 GB - // visible just beyond 4 GB or the end of physical memory, whichever is larger - // NOTE: 16-bit wide REMAP registers store only the highest 10 bits of a 36-bit address, - // (i.e. a multiple of 64 MB) in the lowest 10 bits. - // NOTE: 0x100000000 / (64 MB) == 0x40 - - if (total_dram_64M_multiple < 0x40) { - remap_base = 0x40; // 0x100000000 - remap_limit = - 0x40 + (total_dram_64M_multiple - 0x30) - 1; - } - - pci_write_config16(PCI_DEV(0, 0, 0), REMAPBASE, - remap_base); - pci_write_config16(PCI_DEV(0, 0, 0), REMAPLIMIT, - remap_limit); - } -} - -/** - * If we're configured to use ECC, initialize the SDRAM and clear the E7501's - * ECC error flags. - */ -static void initialize_ecc(void) -{ - uint32_t dram_controller_mode; - - /* Test to see if ECC support is enabled */ - dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); - dram_controller_mode >>= 20; - dram_controller_mode &= 3; - if (dram_controller_mode == 2) { - - uint8_t byte; - - RAM_DEBUG_MESSAGE("Initializing ECC state...\n"); - /* Initialize ECC bits , use ECC zero mode (new to 7501) */ - pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x06); - pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x07); - - // Wait for scrub cycle to complete - do { - byte = - pci_read_config8(PCI_DEV(0, 0, 0), MCHCFGNS); - } while ((byte & 0x08) == 0); - - pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, byte & 0xfc); - RAM_DEBUG_MESSAGE("ECC state initialized.\n"); - - /* Clear the ECC error bits */ - pci_write_config8(PCI_DEV(0, 0, 1), DRAM_FERR, 0x03); - pci_write_config8(PCI_DEV(0, 0, 1), DRAM_NERR, 0x03); - - // Clear DRAM Interface error bits (write-one-clear) - pci_write_config32(PCI_DEV(0, 0, 1), FERR_GLOBAL, 1 << 18); - pci_write_config32(PCI_DEV(0, 0, 1), NERR_GLOBAL, 1 << 18); - - // Start normal ECC scrub - pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 5); - } - -} - -/** - * Program the DRAM Timing register (DRT) of the E7501 (except for CAS# - * latency, which is assumed to have been programmed already), based on the - * parameters of the various installed DIMMs. - * - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms(). - */ -static void configure_e7501_dram_timing(const struct mem_controller *ctrl, - uint8_t dimm_mask) -{ - int i; - uint32_t dram_timing; - int value; - uint8_t slowest_row_precharge = 0; - uint8_t slowest_ras_cas_delay = 0; - uint8_t slowest_active_to_precharge_delay = 0; - uint32_t current_cas_latency = - pci_read_config32(PCI_DEV(0, 0, 0), DRT) & DRT_CAS_MASK; - - // CAS# latency must be programmed beforehand - ASSERT((current_cas_latency == DRT_CAS_2_0) - || (current_cas_latency == DRT_CAS_2_5)); - - // Each timing parameter is determined by the slowest DIMM - - for (i = 0; i < MAX_DIMM_SOCKETS; i++) { - uint16_t dimm_socket_address; - - if (!(dimm_mask & (1 << i))) - continue; // This DIMM not present - - if (i < MAX_DIMM_SOCKETS_PER_CHANNEL) - dimm_socket_address = ctrl->channel0[i]; - else - dimm_socket_address = - ctrl->channel1[i - MAX_DIMM_SOCKETS_PER_CHANNEL]; - - value = - spd_read_byte(dimm_socket_address, - SPD_MIN_ROW_PRECHARGE_TIME); - if (value < 0) - goto hw_err; - if (value > slowest_row_precharge) - slowest_row_precharge = value; - - value = - spd_read_byte(dimm_socket_address, - SPD_MIN_RAS_TO_CAS_DELAY); - if (value < 0) - goto hw_err; - if (value > slowest_ras_cas_delay) - slowest_ras_cas_delay = value; - - value = - spd_read_byte(dimm_socket_address, - SPD_MIN_ACTIVE_TO_PRECHARGE_DELAY); - if (value < 0) - goto hw_err; - if (value > slowest_active_to_precharge_delay) - slowest_active_to_precharge_delay = value; - } - - // NOTE for timing parameters: - // At 133 MHz, 1 clock == 7.52 ns - - /* Read the initial state */ - dram_timing = pci_read_config32(PCI_DEV(0, 0, 0), DRT); - - /* Trp */ - - // E7501 supports only 2 or 3 clocks for tRP - if (slowest_row_precharge > ((22 << 2) | (2 << 0))) - die("unsupported DIMM tRP"); // > 22.5 ns: 4 or more clocks - else if (slowest_row_precharge > (15 << 2)) - dram_timing &= ~(1 << 0); // > 15.0 ns: 3 clocks - else - dram_timing |= (1 << 0); // <= 15.0 ns: 2 clocks - - /* Trcd */ - - // E7501 supports only 2 or 3 clocks for tRCD - // Use the same value for both read & write - dram_timing &= ~((1 << 3) | (3 << 1)); - if (slowest_ras_cas_delay > ((22 << 2) | (2 << 0))) - die("unsupported DIMM tRCD"); // > 22.5 ns: 4 or more clocks - else if (slowest_ras_cas_delay > (15 << 2)) - dram_timing |= (2 << 1); // > 15.0 ns: 3 clocks - else - dram_timing |= ((1 << 3) | (3 << 1)); // <= 15.0 ns: 2 clocks - - /* Tras */ - - // E7501 supports only 5, 6, or 7 clocks for tRAS - // 5 clocks ~= 37.6 ns, 6 clocks ~= 45.1 ns, 7 clocks ~= 52.6 ns - dram_timing &= ~(3 << 9); - - if (slowest_active_to_precharge_delay > 52) - die("unsupported DIMM tRAS"); // > 52 ns: 8 or more clocks - else if (slowest_active_to_precharge_delay > 45) - dram_timing |= (0 << 9); // 46-52 ns: 7 clocks - else if (slowest_active_to_precharge_delay > 37) - dram_timing |= (1 << 9); // 38-45 ns: 6 clocks - else - dram_timing |= (2 << 9); // < 38 ns: 5 clocks - - /* Trd */ - - /* Set to a 7 clock read delay. This is for 133MHz - * with a CAS latency of 2.5 if 2.0 a 6 clock - * delay is good */ - - dram_timing &= ~(7 << 24); // 7 clocks - if (current_cas_latency == DRT_CAS_2_0) - dram_timing |= (1 << 24); // 6 clocks - - /* - * Back to Back Read-Write Turn Around - */ - /* Set to a 5 clock back to back read to write turn around. - * 4 is a good delay if the CAS latency is 2.0 */ - - dram_timing &= ~(1 << 28); // 5 clocks - if (current_cas_latency == DRT_CAS_2_0) - dram_timing |= (1 << 28); // 4 clocks - - pci_write_config32(PCI_DEV(0, 0, 0), DRT, dram_timing); - - return; - - hw_err: - die(SPD_ERROR); -} - -/** - * Determine the shortest CAS# latency that the E7501 and all DIMMs have in - * common, and program the E7501 to use it. - * - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms(). - */ -static void configure_e7501_cas_latency(const struct mem_controller *ctrl, - uint8_t dimm_mask) -{ - int i; - int value; - uint32_t dram_timing; - uint16_t maybe_dram_read_timing; - uint32_t dword; - - // CAS# latency bitmasks in SPD_ACCEPTABLE_CAS_LATENCIES format - // NOTE: E7501 supports only 2.0 and 2.5 - uint32_t system_compatible_cas_latencies = - SPD_CAS_LATENCY_2_0 | SPD_CAS_LATENCY_2_5; - uint32_t current_cas_latency; - uint32_t dimm_compatible_cas_latencies; - - for (i = 0; i < MAX_DIMM_SOCKETS; i++) { - - uint16_t dimm_socket_address; - - if (!(dimm_mask & (1 << i))) - continue; // This DIMM not usable - - if (i < MAX_DIMM_SOCKETS_PER_CHANNEL) - dimm_socket_address = ctrl->channel0[i]; - else - dimm_socket_address = - ctrl->channel1[i - MAX_DIMM_SOCKETS_PER_CHANNEL]; - - value = - spd_read_byte(dimm_socket_address, - SPD_ACCEPTABLE_CAS_LATENCIES); - if (value < 0) - goto hw_err; - - dimm_compatible_cas_latencies = value & 0x7f; // Start with all supported by DIMM - current_cas_latency = 1 << log2(dimm_compatible_cas_latencies); // Max supported by DIMM - - // Can we support the highest CAS# latency? - - value = - spd_read_byte(dimm_socket_address, - SPD_MIN_CYCLE_TIME_AT_CAS_MAX); - if (value < 0) - goto hw_err; - - // NOTE: At 133 MHz, 1 clock == 7.52 ns - if (value > 0x75) { - // Our bus is too fast for this CAS# latency - // Remove it from the bitmask of those supported by the DIMM that are compatible - dimm_compatible_cas_latencies &= ~current_cas_latency; - } - // Can we support the next-highest CAS# latency (max - 0.5)? - - current_cas_latency >>= 1; - if (current_cas_latency != 0) { - value = - spd_read_byte(dimm_socket_address, - SPD_SDRAM_CYCLE_TIME_2ND); - if (value < 0) - goto hw_err; - if (value > 0x75) - dimm_compatible_cas_latencies &= - ~current_cas_latency; - } - // Can we support the next-highest CAS# latency (max - 1.0)? - current_cas_latency >>= 1; - if (current_cas_latency != 0) { - value = - spd_read_byte(dimm_socket_address, - SPD_SDRAM_CYCLE_TIME_3RD); - if (value < 0) - goto hw_err; - if (value > 0x75) - dimm_compatible_cas_latencies &= - ~current_cas_latency; - } - // Restrict the system to CAS# latencies compatible with this DIMM - system_compatible_cas_latencies &= - dimm_compatible_cas_latencies; - - /* go to the next DIMM */ - } - - /* After all of the arduous calculation setup with the fastest - * cas latency I can use. - */ - - dram_timing = pci_read_config32(PCI_DEV(0, 0, 0), DRT); - dram_timing &= ~(DRT_CAS_MASK); - - maybe_dram_read_timing = - pci_read_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL); - maybe_dram_read_timing &= 0xF00C; - - if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_0) { - dram_timing |= DRT_CAS_2_0; - maybe_dram_read_timing |= 0xBB1; - } else if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_5) { - - uint32_t dram_row_attributes = - pci_read_config32(PCI_DEV(0, 0, 0), DRA); - - dram_timing |= DRT_CAS_2_5; - - // At CAS# 2.5, DRAM Read Timing (if that's what it its) appears to need a slightly - // different value if all DIMM slots are populated - - if ((dram_row_attributes & 0xff) - && (dram_row_attributes & 0xff00) - && (dram_row_attributes & 0xff0000) - && (dram_row_attributes & 0xff000000)) { - - // All slots populated - maybe_dram_read_timing |= 0x0882; - } else { - // Some unpopulated slots - maybe_dram_read_timing |= 0x0662; - } - } else - die("No CAS# latencies compatible with all DIMMs!!\n"); - - pci_write_config32(PCI_DEV(0, 0, 0), DRT, dram_timing); - - /* set master DLL reset */ - dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88); - dword |= (1 << 26); - pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); - - dword &= 0x0c0007ff; /* patch try register 88 is undocumented tnz */ - dword |= 0xd2109800; - - pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); - - pci_write_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL, - maybe_dram_read_timing); - - dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88); /* reset master DLL reset */ - dword &= ~(1 << 26); - pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); - - return; - - hw_err: - die(SPD_ERROR); -} - -/** - * Configure the refresh interval so that we refresh no more often than - * required by the "most needy" DIMM. Also disable ECC if any of the DIMMs - * don't support it. - * - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms(). - */ -static void configure_e7501_dram_controller_mode(const struct - mem_controller *ctrl, - uint8_t dimm_mask) -{ - int i; - - // Initial settings - uint32_t controller_mode = - pci_read_config32(PCI_DEV(0, 0, 0), DRC); - uint32_t system_refresh_mode = (controller_mode >> 8) & 7; - - // Code below assumes that most aggressive settings are in - // force when we are called, either via E7501 reset defaults - // or by sdram_set_registers(): - // - ECC enabled - // - No refresh - - ASSERT((controller_mode & (3 << 20)) == (2 << 20)); // ECC - ASSERT(!(controller_mode & (7 << 8))); // Refresh - - /* Walk through _all_ dimms and find the least-common denominator for: - * - ECC support - * - refresh rates - */ - - for (i = 0; i < MAX_DIMM_SOCKETS; i++) { - - uint32_t dimm_refresh_mode; - int value; - uint16_t dimm_socket_address; - - if (!(dimm_mask & (1 << i))) { - continue; // This DIMM not usable - } - - if (i < MAX_DIMM_SOCKETS_PER_CHANNEL) - dimm_socket_address = ctrl->channel0[i]; - else - dimm_socket_address = - ctrl->channel1[i - - MAX_DIMM_SOCKETS_PER_CHANNEL]; - - // Disable ECC mode if any one of the DIMMs does not support ECC - // SJM: Should we just die here? E7501 datasheet says non-ECC DIMMs aren't supported. - - value = - spd_read_byte(dimm_socket_address, - SPD_DIMM_CONFIG_TYPE); - die_on_spd_error(value); - if (value != ERROR_SCHEME_ECC) { - controller_mode &= ~(3 << 20); - } - - value = spd_read_byte(dimm_socket_address, SPD_REFRESH); - die_on_spd_error(value); - value &= 0x7f; // Mask off self-refresh bit - if (value > MAX_SPD_REFRESH_RATE) { - printk(BIOS_ERR, "unsupported refresh rate\n"); - continue; - } - // Get the appropriate E7501 refresh mode for this DIMM - dimm_refresh_mode = refresh_rate_map[value]; - if (dimm_refresh_mode > 7) { - printk(BIOS_ERR, "unsupported refresh rate\n"); - continue; - } - // If this DIMM requires more frequent refresh than others, - // update the system setting - if (refresh_frequency[dimm_refresh_mode] > - refresh_frequency[system_refresh_mode]) - system_refresh_mode = dimm_refresh_mode; - -#ifdef SUSPICIOUS_LOOKING_CODE -// SJM NOTE: This code doesn't look right. SPD values are an order of magnitude smaller -// than the clock period of the memory controller. Also, no other northbridge -// looks at SPD_CMD_SIGNAL_INPUT_HOLD_TIME. - - // Switch to 2 clocks for address/command if required by any one of the DIMMs - // NOTE: At 133 MHz, 1 clock == 7.52 ns - value = - spd_read_byte(dimm_socket_address, - SPD_CMD_SIGNAL_INPUT_HOLD_TIME); - die_on_spd_error(value); - if (value >= 0xa0) { /* At 133MHz this constant should be 0x75 */ - controller_mode &= ~(1 << 16); /* Use two clock cyles instead of one */ - } -#endif - - /* go to the next DIMM */ - } - - controller_mode |= (system_refresh_mode << 8); - - // Configure the E7501 - pci_write_config32(PCI_DEV(0, 0, 0), DRC, controller_mode); -} - -/** - * Configure the E7501's DRAM Row Attributes (DRA) registers based on DIMM - * parameters read via SPD. This tells the controller the width of the SDRAM - * chips on each DIMM side (x4 or x8) and the page size of each DIMM side - * (4, 8, 16, or 32 KB). - * - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms(). - */ -static void configure_e7501_row_attributes(const struct mem_controller - *ctrl, uint8_t dimm_mask) -{ - int i; - uint32_t row_attributes = 0; - - for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { - - uint16_t dimm_socket_address = ctrl->channel0[i]; - struct dimm_size page_size; - struct dimm_size sdram_width; - - if (!(dimm_mask & (1 << i))) - continue; // This DIMM not usable - - // Get the relevant parameters via SPD - page_size = sdram_spd_get_page_size(dimm_socket_address); - sdram_width = sdram_spd_get_width(dimm_socket_address); - - // Update the DRAM Row Attributes. - // Page size is encoded as log2(page size in bits) - log2(8 Kb) - // NOTE: 8 Kb = 2^13 - row_attributes |= (page_size.side1 - 13) << (i << 3); // Side 1 of each DIMM is an EVEN row - - if (sdram_width.side2 > 0) - row_attributes |= (page_size.side2 - 13) << ((i << 3) + 4); // Side 2 is ODD - - // Set x4 flags if appropriate - if (sdram_width.side1 == 4) { - row_attributes |= 0x08 << (i << 3); - } - - if (sdram_width.side2 == 4) { - row_attributes |= 0x08 << ((i << 3) + 4); - } - - /* go to the next DIMM */ - } - - /* Write the new row attributes register */ - pci_write_config32(PCI_DEV(0, 0, 0), DRA, row_attributes); -} - -/* - * Enable clock signals for populated DIMM sockets and disable them for - * unpopulated sockets (to reduce EMI). - * - * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms(). - */ -static void enable_e7501_clocks(uint8_t dimm_mask) -{ - int i; - uint8_t clock_disable = pci_read_config8(PCI_DEV(0, 0, 0), CKDIS); - - for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { - - uint8_t socket_mask = 1 << i; - - if (dimm_mask & socket_mask) - clock_disable &= ~socket_mask; // DIMM present, enable clock - else - clock_disable |= socket_mask; // DIMM absent, disable clock - } - - pci_write_config8(PCI_DEV(0, 0, 0), CKDIS, clock_disable); -} - -/* DIMM-dedependent configuration functions */ - -/** - * DDR Receive FIFO RE-Sync (?) - */ -static void RAM_RESET_DDR_PTR(void) -{ - uint8_t byte; - byte = pci_read_config8(PCI_DEV(0, 0, 0), 0x88); - byte |= (1 << 4); - pci_write_config8(PCI_DEV(0, 0, 0), 0x88, byte); - - byte = pci_read_config8(PCI_DEV(0, 0, 0), 0x88); - byte &= ~(1 << 4); - pci_write_config8(PCI_DEV(0, 0, 0), 0x88, byte); -} - -/** - * Set E7501 registers that are either independent of DIMM specifics, or - * establish default settings that will be overridden when we learn the - * specifics. - * - * This sets PCI configuration registers to known good values based on the - * table 'constant_register_values', which are a triple of configuration - * register offset, mask, and bits to set. - */ -static void ram_set_d0f0_regs(void) -{ - int i; - int num_values = ARRAY_SIZE(constant_register_values); - - ASSERT((num_values % 3) == 0); // Bad table? - - for (i = 0; i < num_values; i += 3) { - - uint32_t register_offset = constant_register_values[i]; - uint32_t bits_to_mask = constant_register_values[i + 1]; - uint32_t bits_to_set = constant_register_values[i + 2]; - uint32_t register_value; - - // It's theoretically possible to set values for something other than D0:F0, - // but it's not typically done here - ASSERT(!(register_offset & 0xFFFFFF00)); - - // bits_to_mask and bits_to_set should not reference the same bits - // Again, not strictly an error, but flagged as a potential bug - ASSERT((bits_to_mask & bits_to_set) == 0); - - register_value = - pci_read_config32(PCI_DEV(0, 0, 0), register_offset); - register_value &= bits_to_mask; - register_value |= bits_to_set; - - pci_write_config32(PCI_DEV(0, 0, 0), register_offset, - register_value); - } -} - -/** - * Copy 64 bytes from one location to another. - * - * @param src_addr TODO - * @param dst_addr TODO - */ -static void write_8dwords(const uint32_t *src_addr, u8 *dst_addr) -{ - int i; - for (i = 0; i < 8; i++) { - write32(dst_addr, *src_addr); - src_addr++; - dst_addr += sizeof(uint32_t); - } -} - -/** - * Set the E7501's (undocumented) RCOMP registers. - * - * Per the 855PM datasheet and IXP2800 HW Initialization Reference Manual, - * RCOMP registers appear to affect drive strength, pullup/pulldown offset, - * and slew rate of various signal groups. - * - * Comments below are conjecture based on apparent similarity between the - * E7501 and these two chips. - */ -static void ram_set_rcomp_regs(void) -{ - uint32_t dword; - uint8_t maybe_strength_control; - - RAM_DEBUG_MESSAGE("Setting RCOMP registers.\n"); - - /*enable access to the rcomp bar */ - dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST); - dword |= (1 << 22); - pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST, dword); - - // Set the RCOMP MMIO base address - pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_SMRBASE, - (uintptr_t)RCOMP_MMIO); - - // Block RCOMP updates while we configure the registers - dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); - dword |= (1 << 9); - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); - - /* Begin to write the RCOMP registers */ - - // Set CMD and DQ/DQS strength to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_DQCMDSTR) & 0x88; - maybe_strength_control |= 0x44; - write8(RCOMP_MMIO + MAYBE_DQCMDSTR, maybe_strength_control); - - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x80); - write16(RCOMP_MMIO + 0x42, 0); - - write_8dwords(maybe_1x_slew_table, RCOMP_MMIO + 0x60); - - // NOTE: some factory BIOS set 0x9088 here. Seems to work either way. - write16(RCOMP_MMIO + 0x40, 0); - - // Set RCVEnOut# strength to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_RCVENSTR) & 0xF8; - maybe_strength_control |= 4; - write8(RCOMP_MMIO + MAYBE_RCVENSTR, maybe_strength_control); - - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x1c0); - write16(RCOMP_MMIO + 0x50, 0); - - // Set CS# strength for x4 SDRAM to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CSBSTR) & 0xF8; - maybe_strength_control |= 4; - write8(RCOMP_MMIO + MAYBE_CSBSTR, maybe_strength_control); - - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x140); - write16(RCOMP_MMIO + 0x48, 0); - - // Set CKE strength for x4 SDRAM to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKESTR) & 0xF8; - maybe_strength_control |= 4; - write8(RCOMP_MMIO + MAYBE_CKESTR, maybe_strength_control); - - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0xa0); - write16(RCOMP_MMIO + 0x44, 0); - - // Set CK strength for x4 SDRAM to 1x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKSTR) & 0xF8; - maybe_strength_control |= 1; - write8(RCOMP_MMIO + MAYBE_CKSTR, maybe_strength_control); - - write_8dwords(maybe_pull_updown_offset_table, RCOMP_MMIO + 0x180); - write16(RCOMP_MMIO + 0x4c, 0); - - write8(RCOMP_MMIO + 0x2c, 0xff); - - // Set the digital filter length to 8 (?) - dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); - - // NOTE: Some factory BIOS don't do this. - // Doesn't seem to matter either way. - dword &= ~2; - - dword |= 1; - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); - - /* Wait 40 usec */ - SLOW_DOWN_IO; - - /* unblock updates */ - dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); - dword &= ~(1 << 9); - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); - - // Force a RCOMP measurement cycle? - dword |= (1 << 8); - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); - dword &= ~(1 << 8); - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); - - /* Wait 40 usec */ - SLOW_DOWN_IO; - - /*disable access to the rcomp bar */ - dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST); - dword &= ~(1 << 22); - pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST, dword); - -} - -/*----------------------------------------------------------------------------- -Public interface: ------------------------------------------------------------------------------*/ - -/** - * Go through the JEDEC initialization sequence for all DIMMs, then enable - * refresh and initialize ECC and memory to zero. Upon exit, SDRAM is up - * and running. - * - * @param controllers Not used. - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - */ -static void sdram_enable(int controllers, - const struct mem_controller *ctrl) -{ - uint8_t dimm_mask = pci_read_config16(PCI_DEV(0, 0, 0), SKPD); - uint32_t dram_controller_mode; - - if (dimm_mask == 0) - return; - - /* 1 & 2 Power up and start clocks */ - RAM_DEBUG_MESSAGE("Ram Enable 1\n"); - RAM_DEBUG_MESSAGE("Ram Enable 2\n"); - - /* A 200us delay is needed */ - DO_DELAY; EXTRA_DELAY; - - /* 3. Apply NOP */ - RAM_DEBUG_MESSAGE("Ram Enable 3\n"); - do_ram_command(RAM_COMMAND_NOP, 0); - EXTRA_DELAY; - - /* 4 Precharge all */ - RAM_DEBUG_MESSAGE("Ram Enable 4\n"); - do_ram_command(RAM_COMMAND_PRECHARGE, 0); - EXTRA_DELAY; - /* wait until the all banks idle state... */ - - /* 5. Issue EMRS to enable DLL */ - RAM_DEBUG_MESSAGE("Ram Enable 5\n"); - do_ram_command(RAM_COMMAND_EMRS, - SDRAM_EXTMODE_DLL_ENABLE | - SDRAM_EXTMODE_DRIVE_NORMAL); - EXTRA_DELAY; - - /* 6. Reset DLL */ - RAM_DEBUG_MESSAGE("Ram Enable 6\n"); - set_ram_mode(E7501_SDRAM_MODE | SDRAM_MODE_DLL_RESET); - EXTRA_DELAY; - /* Ensure a 200us delay between the DLL reset in step 6 and the final - * mode register set in step 9. - * Infineon needs this before any other command is sent to the ram. - */ - DO_DELAY; EXTRA_DELAY; - - /* 7 Precharge all */ - RAM_DEBUG_MESSAGE("Ram Enable 7\n"); - do_ram_command(RAM_COMMAND_PRECHARGE, 0); - EXTRA_DELAY; - - /* 8 Now we need 2 AUTO REFRESH / CBR cycles to be performed */ - RAM_DEBUG_MESSAGE("Ram Enable 8\n"); - do_ram_command(RAM_COMMAND_CBR, 0); - EXTRA_DELAY; - do_ram_command(RAM_COMMAND_CBR, 0); - EXTRA_DELAY; - - /* And for good luck 6 more CBRs */ - do_ram_command(RAM_COMMAND_CBR, 0); - EXTRA_DELAY; - do_ram_command(RAM_COMMAND_CBR, 0); - EXTRA_DELAY; - do_ram_command(RAM_COMMAND_CBR, 0); - EXTRA_DELAY; - do_ram_command(RAM_COMMAND_CBR, 0); - EXTRA_DELAY; - do_ram_command(RAM_COMMAND_CBR, 0); - EXTRA_DELAY; - do_ram_command(RAM_COMMAND_CBR, 0); - EXTRA_DELAY; - - /* 9 mode register set */ - RAM_DEBUG_MESSAGE("Ram Enable 9\n"); - set_ram_mode(E7501_SDRAM_MODE | SDRAM_MODE_NORMAL); - EXTRA_DELAY; - - /* 10 DDR Receive FIFO RE-Sync */ - RAM_DEBUG_MESSAGE("Ram Enable 10\n"); - RAM_RESET_DDR_PTR(); - EXTRA_DELAY; - - /* 11 normal operation */ - RAM_DEBUG_MESSAGE("Ram Enable 11\n"); - do_ram_command(RAM_COMMAND_NORMAL, 0); - EXTRA_DELAY; - - // Reconfigure the row boundaries and Top of Low Memory - // to match the true size of the DIMMs - configure_e7501_ram_addresses(ctrl, dimm_mask); - - /* Finally enable refresh */ - dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); - dram_controller_mode |= (1 << 29); - pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); - EXTRA_DELAY; - initialize_ecc(); - - dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); /* FCS_EN */ - dram_controller_mode |= (1 << 17); // NOTE: undocumented reserved bit - pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); - - RAM_DEBUG_MESSAGE("Northbridge following SDRAM init:\n"); - DUMPNORTH(); -} - -/** - * Configure SDRAM controller parameters that depend on characteristics of the - * DIMMs installed in the system. These characteristics are read from the - * DIMMs via the standard Serial Presence Detect (SPD) interface. - * - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - */ -static void sdram_set_spd_registers(const struct mem_controller *ctrl) -{ - uint8_t dimm_mask; - - RAM_DEBUG_MESSAGE("Reading SPD data...\n"); - - dimm_mask = spd_get_supported_dimms(ctrl); - - if (dimm_mask == 0) { - printk(BIOS_DEBUG, "No usable memory for this controller\n"); - } else { - enable_e7501_clocks(dimm_mask); - - RAM_DEBUG_MESSAGE("setting based on SPD data...\n"); - - configure_e7501_row_attributes(ctrl, dimm_mask); - configure_e7501_dram_controller_mode(ctrl, dimm_mask); - configure_e7501_cas_latency(ctrl, dimm_mask); - RAM_RESET_DDR_PTR(); - - configure_e7501_dram_timing(ctrl, dimm_mask); - DO_DELAY; - RAM_DEBUG_MESSAGE("done\n"); - } - - /* NOTE: configure_e7501_ram_addresses() is NOT called here. - * We want to keep the default 64 MB/row mapping until sdram_enable() is called, - * even though the default mapping is almost certainly incorrect. - * The default mapping makes it easy to initialize all of the DIMMs - * even if the total system memory is > 4 GB. - * - * Save the dimm_mask for when sdram_enable is called, so it can call - * configure_e7501_ram_addresses() without having to regenerate the bitmask - * of usable DIMMs. - */ - pci_write_config16(PCI_DEV(0, 0, 0), SKPD, dimm_mask); -} - -/** - * Do basic RAM setup that does NOT depend on serial presence detect - * information (i.e. independent of DIMM specifics). - * - * @param ctrl PCI addresses of memory controller functions, and SMBus - * addresses of DIMM slots on the mainboard. - */ -static void sdram_set_registers(const struct mem_controller *ctrl) -{ - RAM_DEBUG_MESSAGE("Northbridge prior to SDRAM init:\n"); - DUMPNORTH(); - - ram_set_rcomp_regs(); - ram_set_d0f0_regs(); -} diff --git a/src/northbridge/intel/e7501/raminit.h b/src/northbridge/intel/e7501/raminit.h deleted file mode 100644 index 05c3889aa2..0000000000 --- a/src/northbridge/intel/e7501/raminit.h +++ /dev/null @@ -1,20 +0,0 @@ -#ifndef RAMINIT_H -#define RAMINIT_H - -#define MAX_DIMM_SOCKETS_PER_CHANNEL 4 -#define MAX_NUM_CHANNELS 2 -#define MAX_DIMM_SOCKETS (MAX_NUM_CHANNELS * MAX_DIMM_SOCKETS_PER_CHANNEL) - -struct mem_controller { - device_t d0, d0f1; // PCI bus/device/fcns of E7501 memory controller - - // SMBus addresses of DIMM slots for each channel, - // in order from closest to MCH to furthest away - // 0 == not present - uint16_t channel0[MAX_DIMM_SOCKETS_PER_CHANNEL]; - uint16_t channel1[MAX_DIMM_SOCKETS_PER_CHANNEL]; -}; - -void sdram_initialize(int controllers, const struct mem_controller *ctrl); - -#endif /* RAMINIT_H */ diff --git a/src/northbridge/intel/e7501/reset_test.c b/src/northbridge/intel/e7501/reset_test.c deleted file mode 100644 index 62e3283c8f..0000000000 --- a/src/northbridge/intel/e7501/reset_test.c +++ /dev/null @@ -1,18 +0,0 @@ -/* Convert to C by yhlu */ -#define MCH_DRC 0x7c -#define DRC_DONE (1 << 29) - /* If I have already booted once skip a bunch of initialization */ - /* To see if I have already booted I check to see if memory - * has been enabled. - */ -static int bios_reset_detected(void) { - uint32_t dword; - - dword = pci_read_config32(PCI_DEV(0, 0, 0), MCH_DRC); - - if ( (dword & DRC_DONE) != 0 ) { - return 1; - } - - return 0; -} |