diff options
| -rw-r--r-- | src/mainboard/tyan/s2881/mainboard.c | 39 |
1 files changed, 19 insertions, 20 deletions
diff --git a/src/mainboard/tyan/s2881/mainboard.c b/src/mainboard/tyan/s2881/mainboard.c index df7aebcf5e..e781114aca 100644 --- a/src/mainboard/tyan/s2881/mainboard.c +++ b/src/mainboard/tyan/s2881/mainboard.c @@ -2,7 +2,7 @@ * This file is part of the LinuxBIOS project. * * Copyright (C) 2005 Tyan - * Written by Yinghai Lu <yhlu@tyan.com> for Tyan. + * (Written by Yinghai Lu <yhlu@tyan.com> for Tyan) * Copyright (C) 2007 Ward Vandewege <ward@gnu.org> * * This program is free software; you can redistribute it and/or modify @@ -21,9 +21,9 @@ */ #include <device/device.h> -#include "chip.h" #include <console/console.h> #include <device/smbus.h> +#include "chip.h" /** * Do some S2881-specific HWM initialization for the ADT7463 chip. @@ -31,28 +31,24 @@ * See Analog Devices ADT7463 datasheet, Rev C (2004): * http://www.analog.com/en/prod/0,,766_825_ADT7463,00.html */ -static void dummy_init(device_t dev) +static void adt7463_init(device_t dev) { - device_t smbus_dev; - device_t adt7463; + device_t smbus_dev, adt7463; struct device_path path; - int result; /* Find the SMBus controller (AMD-8111). */ smbus_dev = dev_find_device(0x1022, 0x746b, 0); - if (!smbus_dev) { + if (!smbus_dev) die("SMBus controller not found\n"); - } printk_debug("SMBus controller found\n"); /* Find the ADT7463 device. */ path.type = DEVICE_PATH_I2C; path.u.i2c.device = 0x2d; adt7463 = find_dev_path(smbus_dev->link, &path); - if (!adt7463) { + if (!adt7463) die("ADT7463 not found\n"); - } printk_debug("ADT7463 found\n"); /* Set all fans to 'Fastest Speed Calculated by All 3 Temperature @@ -62,9 +58,10 @@ static void dummy_init(device_t dev) result = smbus_write_byte(adt7463, 0x5d, 0xc2); result = smbus_write_byte(adt7463, 0x5e, 0xc2); - /* Make sure that our fans never stop when temp. falls below Tmin, - but rather keep going at minimum duty cycle (applies to automatic - fan control mode only). */ + /* Make sure that our fans never stop when temp. falls below Tmin, + * but rather keep going at minimum duty cycle (applies to automatic + * fan control mode only). + */ result = smbus_write_byte(adt7463, 0x62, 0xc0); /* Set minimum PWM duty cycle to 25%, rather than the default 50%. */ @@ -73,16 +70,18 @@ static void dummy_init(device_t dev) result = smbus_write_byte(adt7463, 0x66, 0x40); /* Set Tmin to 55C, rather than the default 90C. Above this temperature - the fans will start blowing harder as temperature increases - (automatic mode only). */ + * the fans will start blowing harder as temperature increases + * (automatic mode only). + */ result = smbus_write_byte(adt7463, 0x67, 0x37); result = smbus_write_byte(adt7463, 0x68, 0x37); result = smbus_write_byte(adt7463, 0x69, 0x37); /* Set THERM limit to 70C, rather than the default 100C. - The fans will kick in at 100% if the sensors reach this temperature, - (only in automatic mode, but supposedly even when hardware is - locked up). This is a failsafe measure. */ + * The fans will kick in at 100% if the sensors reach this temperature, + * (only in automatic mode, but supposedly even when hardware is + * locked up). This is a failsafe measure. + */ result = smbus_write_byte(adt7463, 0x6a, 0x46); result = smbus_write_byte(adt7463, 0x6b, 0x46); result = smbus_write_byte(adt7463, 0x6c, 0x46); @@ -96,7 +95,7 @@ static void dummy_init(device_t dev) /* Set TACH measurements to normal (1/second). */ result = smbus_write_byte(adt7463, 0x78, 0xf0); - printk_debug("ADT7463 properly initialized"); + printk_debug("ADT7463 properly initialized\n"); } static void dummy_noop(device_t dummy) @@ -107,7 +106,7 @@ static struct device_operations dummy_operations = { .read_resources = dummy_noop, .set_resources = dummy_noop, .enable_resources = dummy_noop, - .init = dummy_init, + .init = adt7463_init, }; static unsigned int scan_root_bus(device_t root, unsigned int max) |