via epia is putting out bytes!

ron


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1153 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

3 files changed, 16 insertions, 18 deletions

diff --git a/src/mainboard/via/epia/auto.c b/src/mainboard/via/epia/auto.c
index 859aadc614..31bb04363c 100644
--- a/src/mainboard/via/epia/auto.c
+++ b/src/mainboard/via/epia/auto.c
@@ -52,7 +52,9 @@ static inline int spd_read_byte(unsigned device, unsigned address)
 
 static void main(void)
 {
+  unsigned long x;
   /*	init_timer();*/
+  outb(5, 0x80);
 
 	enable_vt8231_serial();
 	uart_init();
diff --git a/src/mainboard/via/epia/failover.c b/src/mainboard/via/epia/failover.c
index 8eeeaef7e1..bd0df4e89d 100644
--- a/src/mainboard/via/epia/failover.c
+++ b/src/mainboard/via/epia/failover.c
@@ -5,20 +5,13 @@
 #include <arch/io.h>
 #include "arch/romcc_io.h"
 #include "pc80/mc146818rtc_early.c"
-#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
-#include "northbridge/amd/amdk8/early_ht.c"
 #include "cpu/p6/boot_cpu.c"
-#include "northbridge/amd/amdk8/reset_test.c"
 
 static void main(void)
 {
-	/* Nothing special needs to be done to find bus 0 */
-	/* Allow the HT devices to be found */
-	enumerate_ht_chain(0);
-
-	/* Setup the 8111 */
-	amd8111_enable_rom();
+  /* for now, just always assume failure */
 
+#if 0
 	/* Is this a cpu reset? */
 	if (cpu_init_detected()) {
 		if (last_boot_normal()) {
@@ -27,12 +20,10 @@ static void main(void)
 			asm("jmp __cpu_reset");
 		}
 	}
-	/* Is this a secondary cpu? */
-	else if (!boot_cpu() && last_boot_normal()) {
-		asm("jmp __normal_image");
-	}
+
 	/* This is the primary cpu how should I boot? */
 	else if (do_normal_boot()) {
 		asm("jmp __normal_image");
 	}
+#endif
 }
diff --git a/src/southbridge/via/vt8231/vt8231_early_serial.c b/src/southbridge/via/vt8231/vt8231_early_serial.c
index 168ee07377..ca7831df42 100644
--- a/src/southbridge/via/vt8231/vt8231_early_serial.c
+++ b/src/southbridge/via/vt8231/vt8231_early_serial.c
@@ -31,19 +31,24 @@ vt8231_writesioword(uint16_t reg, uint16_t val) {
 
 static void
 enable_vt8231_serial(void) {
+  unsigned long x;
+  uint8_t c;
   device_t dev;
-
-  dev = pci_locate_device(PCI_ID(0x1106,0x3065), 0);
+  outb(6, 0x80);
+  dev = pci_locate_device(PCI_ID(0x1106,0x8231), 0);
   
   if (dev == PCI_DEV_INVALID) {
+    outb(7, 0x80);
     die("Serial controller not found\r\n");
   }
-  
 
   /* first, you have to enable the superio and superio config. 
-     put a 3 in devfn 38 reg 85
+     put a 6 reg 80
   */
-  pci_write_config8(dev, 0x85, 3);
+  c = pci_read_config8(dev, 0x50);
+  c |= 6;
+  pci_write_config8(dev, 0x50, c);
+  outb(2, 0x80);
   // now go ahead and set up com1. 
   // set address
   vt8231_writesuper(0xf4, 0xfe);