summaryrefslogtreecommitdiff
path: root/src
diff options
context:
space:
mode:
authorJoseph Smith <joe@smittys.pointclark.net>2007-10-30 21:55:11 +0000
committerUwe Hermann <uwe@hermann-uwe.de>2007-10-30 21:55:11 +0000
commit68d8a56cc56ab9805bee85c08f7211ef8455ca4d (patch)
tree9f47b9ccf67f54a8ce95b67c4e225f1f7e3a4474 /src
parentc4590dae6aaed753ecac00351262936084807d48 (diff)
Various fixes and improvements of the 82801xx code.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net> Acked-by: Corey Osgood <corey.osgood@gmail.com> Acked-by: Uwe Hermann <uwe@hermann-uwe.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2912 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Diffstat (limited to 'src')
-rw-r--r--src/southbridge/intel/i82801xx/i82801xx.h25
-rw-r--r--src/southbridge/intel/i82801xx/i82801xx_lpc.c243
2 files changed, 170 insertions, 98 deletions
diff --git a/src/southbridge/intel/i82801xx/i82801xx.h b/src/southbridge/intel/i82801xx/i82801xx.h
index fa306bc0a4..41179c9640 100644
--- a/src/southbridge/intel/i82801xx/i82801xx.h
+++ b/src/southbridge/intel/i82801xx/i82801xx.h
@@ -33,21 +33,30 @@ extern void i82801xx_enable(device_t dev);
#define RTC_CONF 0xd8
#define GEN_PMCON_3 0xa4
-#define PCICMD 0x04
#define PMBASE 0x40
-#define PM_BASE_ADDR 0x1100
#define ACPI_CNTL 0x44
#define BIOS_CNTL 0x4E
-#define GPIO_BASE 0x58
-#define GPIO_BASE_ADDR 0x1180
-#define GPIO_CNTL 0x5C
+#define GPIO_BASE_ICH0_5 0x58 /* LPC GPIO Base Addr. Reg. (ICH0-ICH5) */
+#define GPIO_BASE_ICH6_9 0x48 /* LPC GPIO Base Address Register (ICH6-ICH9) */
+#define GPIO_CNTL_ICH0_5 0x5C /* LPC GPIO Control Register (ICH0-ICH5) */
+#define GPIO_CNTL_ICH6_9 0x4C /* LPC GPIO Control Register (ICH6-ICH9) */
+
#define PIRQA_ROUT 0x60
+#define PIRQB_ROUT 0x61
+#define PIRQC_ROUT 0x62
+#define PIRQD_ROUT 0x63
#define PIRQE_ROUT 0x68
-#define COM_DEC 0xE0
-#define LPC_EN 0xE6
+#define PIRQF_ROUT 0x69
+#define PIRQG_ROUT 0x6A
+#define PIRQH_ROUT 0x6B
+
#define FUNC_DIS 0xF2
-#define CMD 0x04
+#define COM_DEC 0xE0 /* LPC I/F Communication Port Decode Ranges (ICH0-ICH5) */
+#define LPC_IO_DEC 0x80 /* IO Decode Ranges Register (ICH6-ICH9) */
+#define LPC_EN_ICH0_5 0xE6 /* LPC IF Enables Register (ICH0-ICH5) */
+#define LPC_EN_ICH6_9 0x82 /* LPC IF Enables Register (ICH6-ICH9) */
+
#define SBUS_NUM 0x19
#define SUB_BUS_NUM 0x1A
#define SMLT 0x1B
diff --git a/src/southbridge/intel/i82801xx/i82801xx_lpc.c b/src/southbridge/intel/i82801xx/i82801xx_lpc.c
index 6d35c187ec..eefd7bb9f1 100644
--- a/src/southbridge/intel/i82801xx/i82801xx_lpc.c
+++ b/src/southbridge/intel/i82801xx/i82801xx_lpc.c
@@ -32,14 +32,53 @@
#include <arch/io.h>
#include "i82801xx.h"
+#define PMBASE_ADDR 0x00000400 /* ACPI Base Address Register */
+#define GPIO_BASE_ADDR 0x00000500 /* GPIO Base Address Register */
+
#define NMI_OFF 0
-void i82801xx_enable_ioapic(struct device *dev)
+/* PIRQ[n]_ROUT[3:0] - PIRQ Routing Control
+ * 0x00 - 0000 = Reserved
+ * 0x01 - 0001 = Reserved
+ * 0x02 - 0010 = Reserved
+ * 0x03 - 0011 = IRQ3
+ * 0x04 - 0100 = IRQ4
+ * 0x05 - 0101 = IRQ5
+ * 0x06 - 0110 = IRQ6
+ * 0x07 - 0111 = IRQ7
+ * 0x08 - 1000 = Reserved
+ * 0x09 - 1001 = IRQ9
+ * 0x0A - 1010 = IRQ10
+ * 0x0B - 1011 = IRQ11
+ * 0x0C - 1100 = IRQ12
+ * 0x0D - 1101 = Reserved
+ * 0x0E - 1110 = IRQ14
+ * 0x0F - 1111 = IRQ15
+ * PIRQ[n]_ROUT[7] - PIRQ Routing Control
+ * 0x80 - The PIRQ is not routed.
+ */
+
+#define PIRQA 0x03
+#define PIRQB 0x05
+#define PIRQC 0x06
+#define PIRQD 0x07
+#define PIRQE 0x09
+#define PIRQF 0x0A
+#define PIRQG 0x0B
+#define PIRQH 0x0C
+
+void i82801xx_enable_apic(struct device *dev)
{
uint32_t reg32;
volatile uint32_t *ioapic_index = (volatile uint32_t *)0xfec00000;
volatile uint32_t *ioapic_data = (volatile uint32_t *)0xfec00010;
+ /* Set ACPI base address (I/O space). */
+ pci_write_config32(dev, PMBASE, (PMBASE_ADDR | 1));
+
+ /* Enable ACPI I/O and power management. */
+ pci_write_config8(dev, ACPI_CNTL, 0x10);
+
reg32 = pci_read_config32(dev, GEN_CNTL);
reg32 |= (3 << 7); /* Enable IOAPIC */
reg32 |= (1 << 13); /* Coprocessor error enable */
@@ -58,8 +97,8 @@ void i82801xx_enable_ioapic(struct device *dev)
die("APIC Error\n");
/* TODO: From i82801ca, needed/useful on other ICH? */
- *ioapic_index = 3; // Select Boot Configuration register
- *ioapic_data = 1; // Use Processor System Bus to deliver interrupts
+ *ioapic_index = 3; /* Select Boot Configuration register. */
+ *ioapic_data = 1; /* Use Processor System Bus to deliver interrupts. */
}
void i82801xx_enable_serial_irqs(struct device *dev)
@@ -72,22 +111,67 @@ void i82801xx_enable_serial_irqs(struct device *dev)
/* TODO: Explain/#define the real meaning of these magic numbers. */
}
-void i82801xx_lpc_route_dma(struct device *dev, uint8_t mask)
+static void i82801xx_pirq_init(device_t dev, uint16_t ich_model)
{
- uint16_t reg16;
- int i;
+ /* Route PIRQA - PIRQD. */
+ pci_write_config8(dev, PIRQA_ROUT, PIRQA);
+ pci_write_config8(dev, PIRQB_ROUT, PIRQB);
+ pci_write_config8(dev, PIRQC_ROUT, PIRQC);
+ pci_write_config8(dev, PIRQD_ROUT, PIRQD);
+
+ /* Route PIRQE - PIRQH (for ICH2-ICH9). */
+ if (ich_model >= 0x2440) {
+ pci_write_config8(dev, PIRQE_ROUT, PIRQE);
+ pci_write_config8(dev, PIRQF_ROUT, PIRQF);
+ pci_write_config8(dev, PIRQG_ROUT, PIRQG);
+ pci_write_config8(dev, PIRQH_ROUT, PIRQH);
+ }
+}
- reg16 = pci_read_config16(dev, PCI_DMA_CFG);
- reg16 &= 0x300;
- for (i = 0; i < 8; i++) {
- if (i == 4)
- continue;
- reg16 |= ((mask & (1 << i)) ? 3 : 1) << (i * 2);
+static void i82801xx_power_options(device_t dev)
+{
+ uint8_t byte;
+ int pwr_on = -1;
+ int nmi_option;
+
+ /* power after power fail */
+ /* FIXME this doesn't work! */
+ /* Which state do we want to goto after g3 (power restored)?
+ * 0 == S0 Full On
+ * 1 == S5 Soft Off
+ */
+ pci_write_config8(dev, GEN_PMCON_3, pwr_on ? 0 : 1);
+ printk_info("Set power %s if power fails\n", pwr_on ? "on" : "off");
+
+ /* Set up NMI on errors. */
+ byte = inb(0x61);
+ byte &= ~(1 << 3); /* IOCHK# NMI Enable */
+ byte &= ~(1 << 2); /* PCI SERR# Enable */
+ outb(byte, 0x61);
+ byte = inb(0x70);
+
+ nmi_option = NMI_OFF;
+ get_option(&nmi_option, "nmi");
+ if (nmi_option) {
+ byte &= ~(1 << 7); /* Set NMI. */
+ outb(byte, 0x70);
+ }
+}
+
+static void gpio_init(device_t dev, uint16_t ich_model)
+{
+ /* Set the value for GPIO base address register and enable GPIO.
+ * Note: ICH-ICH5 registers differ from ICH6-ICH9.
+ */
+ if (ich_model <= 0x24D0) {
+ pci_write_config32(dev, GPIO_BASE_ICH0_5, (GPIO_BASE_ADDR | 1));
+ pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
+ } else if (ich_model >= 0x2640) {
+ pci_write_config32(dev, GPIO_BASE_ICH6_9, (GPIO_BASE_ADDR | 1));
+ pci_write_config8(dev, GPIO_CNTL_ICH6_9, 0x10);
}
- pci_write_config16(dev, PCI_DMA_CFG, reg16);
}
-/* TODO: Needs serious cleanup/comments. */
void i82801xx_rtc_init(struct device *dev)
{
uint8_t reg8;
@@ -97,46 +181,47 @@ void i82801xx_rtc_init(struct device *dev)
reg8 = pci_read_config8(dev, GEN_PMCON_3);
rtc_failed = reg8 & RTC_BATTERY_DEAD;
if (rtc_failed) {
- reg8 &= ~(1 << 1); /* preserve the power fail state */
+ reg8 &= ~(1 << 1); /* Preserve the power fail state. */
pci_write_config8(dev, GEN_PMCON_3, reg8);
}
reg32 = pci_read_config32(dev, GEN_STS);
rtc_failed |= reg32 & (1 << 2);
rtc_init(rtc_failed);
+
+ /* Enable access to the upper 128 byte bank of CMOS RAM. */
+ pci_write_config8(dev, RTC_CONF, 0x04);
}
-void i82801xx_1f0_misc(struct device *dev)
+void i82801xx_lpc_route_dma(struct device *dev, uint8_t mask)
{
- /* TODO: break this down into smaller functions */
+ uint16_t reg16;
+ int i;
- //move to acpi_enable or something
- /* Set ACPI base address to 0x1100 (I/O space) */
- pci_write_config32(dev, PMBASE, PM_BASE_ADDR | 1);
- /* Enable ACPI I/O and power management */
- pci_write_config8(dev, ACPI_CNTL, 0x10);
- /* Set GPIO base address to 0x1180 (I/O space) */
- pci_write_config32(dev, GPIO_BASE, GPIO_BASE_ADDR | 1);
- /* Enable GPIO */
- pci_write_config8(dev, GPIO_CNTL, 0x10);
-
- //get rid of?
- /* Route PIRQA to IRQ11, PIRQB to IRQ3, PIRQC to IRQ5, PIRQD to IRQ10 */
- pci_write_config32(dev, PIRQA_ROUT, 0x0A05030B);
- /* Route PIRQE to IRQ7. Leave PIRQF - PIRQH unrouted */
- pci_write_config8(dev, PIRQE_ROUT, 0x07);
-
- //move to i82801xx_init
- /* Prevent LPC disabling, enable parity errors, and SERR# (System Error) */
- pci_write_config16(dev, PCI_COMMAND, 0x014f);
- /* Enable access to the upper 128 byte bank of CMOS RAM */
- pci_write_config8(dev, RTC_CONF, 0x04);
- /* Decode 0x3F8-0x3FF (COM1) for COMA port, 0x2F8-0x2FF (COM2) for COMB */
- pci_write_config8(dev, COM_DEC, 0x10);
- /* LPT decode defaults to 0x378-0x37F and 0x778-0x77F
- * Floppy decode defaults to 0x3F0-0x3F5, 0x3F7 */
- /* Enable: COMA, COMB, LPT, Floppy
- * Disable: Microcontroller, Sound, Gameport */
- pci_write_config16(dev, LPC_EN, 0x000F);
+ reg16 = pci_read_config16(dev, PCI_DMA_CFG);
+ reg16 &= 0x300;
+ for (i = 0; i < 8; i++) {
+ if (i == 4)
+ continue;
+ reg16 |= ((mask & (1 << i)) ? 3 : 1) << (i * 2);
+ }
+ pci_write_config16(dev, PCI_DMA_CFG, reg16);
+}
+
+static void i82801xx_lpc_decode_en(device_t dev, uint16_t ich_model)
+{
+ /* Decode 0x3F8-0x3FF (COM1) for COMA port, 0x2F8-0x2FF (COM2) for COMB.
+ * LPT decode defaults to 0x378-0x37F and 0x778-0x77F.
+ * Floppy decode defaults to 0x3F0-0x3F5, 0x3F7.
+ * We also need to set the value for LPC I/F Enables Register.
+ * Note: ICH-ICH5 registers differ from ICH6-ICH9.
+ */
+ if (ich_model <= 0x24D0) {
+ pci_write_config8(dev, COM_DEC, 0x10);
+ pci_write_config16(dev, LPC_EN_ICH0_5, 0x300F);
+ } else if (ich_model >= 0x2640) {
+ pci_write_config8(dev, LPC_IO_DEC, 0x10);
+ pci_write_config16(dev, LPC_EN_ICH6_9, 0x300F);
+ }
}
static void enable_hpet(struct device *dev)
@@ -146,7 +231,7 @@ static void enable_hpet(struct device *dev)
uint32_t code = (0 & 0x3);
reg32 = pci_read_config32(dev, GEN_CNTL);
- reg32 |= (1 << 17); /* Enable HPET */
+ reg32 |= (1 << 17); /* Enable HPET. */
/*
* Bits [16:15] Memory Address Range
* 00 FED0_0000h - FED0_03FFh
@@ -156,67 +241,45 @@ static void enable_hpet(struct device *dev)
*/
reg32 &= ~(3 << 15); /* Clear it */
reg32 |= (code << 15);
- /* reg32 is never written to anywhere? */
+ /* TODO: reg32 is never written to anywhere? */
printk_debug("Enabling HPET @0x%x\n", HPET_ADDR | (code << 12));
#endif
}
static void lpc_init(struct device *dev)
{
- uint8_t byte;
- int pwr_on = -1;
- int nmi_option;
+ uint16_t ich_model = pci_read_config16(dev, PCI_DEVICE_ID);
- /* IO APIC initialization */
- i82801xx_enable_ioapic(dev);
+ /* Set the value for PCI command register. */
+ pci_write_config16(dev, PCI_COMMAND, 0x000f);
- i82801xx_enable_serial_irqs(dev);
+ /* IO APIC initialization. */
+ i82801xx_enable_apic(dev);
- /* TODO: Find out if this is being used/works */
-#ifdef SUSPICIOUS_LOOKING_CODE
- /* The ICH-4 datasheet does not mention this configuration register.
- * This code may have been inherited (incorrectly) from code for
- * the AMD 766 southbridge, which *does* support this functionality.
- */
+ i82801xx_enable_serial_irqs(dev);
- /* Posted memory write enable */
- byte = pci_read_config8(dev, 0x46);
- pci_write_config8(dev, 0x46, byte | (1 << 0));
-#endif
+ /* Setup the PIRQ. */
+ i82801xx_pirq_init(dev, ich_model);
- /* power after power fail */
- /* FIXME this doesn't work! */
- /* Which state do we want to goto after g3 (power restored)?
- * 0 == S0 Full On
- * 1 == S5 Soft Off
- */
- pci_write_config8(dev, GEN_PMCON_3, pwr_on ? 0 : 1);
- printk_info("Set power %s if power fails\n", pwr_on ? "on" : "off");
+ /* Setup power options. */
+ i82801xx_power_options(dev);
- /* Set up NMI on errors */
- byte = inb(0x61);
- byte &= ~(1 << 3); /* IOCHK# NMI Enable */
- byte &= ~(1 << 2); /* PCI SERR# Enable */
- outb(byte, 0x61);
- byte = inb(0x70);
+ /* Set the state of the GPIO lines. */
+ gpio_init(dev, ich_model);
- nmi_option = NMI_OFF;
- get_option(&nmi_option, "nmi");
- if (nmi_option) {
- byte &= ~(1 << 7); /* Set NMI */
- outb(byte, 0x70);
- }
-
- /* Initialize the real time clock */
+ /* Initialize the real time clock. */
i82801xx_rtc_init(dev);
+ /* Route DMA. */
i82801xx_lpc_route_dma(dev, 0xff);
- /* Initialize isa dma */
+ /* Initialize ISA DMA. */
isa_dma_init();
- i82801xx_1f0_misc(dev);
- /* Initialize the High Precision Event Timers, if present */
+ /* Setup decode ports and LPC I/F enables. */
+ i82801xx_lpc_decode_en(dev, ich_model);
+
+ /* Initialize the High Precision Event Timers, if present. */
enable_hpet(dev);
}
@@ -224,10 +287,10 @@ static void i82801xx_lpc_read_resources(device_t dev)
{
struct resource *res;
- /* Get the normal pci resources of this device */
+ /* Get the normal PCI resources of this device. */
pci_dev_read_resources(dev);
- /* Add an extra subtractive resource for both memory and I/O */
+ /* Add an extra subtractive resource for both memory and I/O. */
res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0));
res->flags =
IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;