haswell: Add initial support for Haswell platforms

The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.

This code partially gets up through the romstage just before training
memory on a Haswell reference board.

Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>

1 files changed, 57 insertions, 0 deletions

diff --git a/src/southbridge/intel/lynxpoint/early_usb.c b/src/southbridge/intel/lynxpoint/early_usb.c
new file mode 100644
index 0000000000..b2e009123e
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/early_usb.c
@@ -0,0 +1,57 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/console.h>
+#include <device/pci_ids.h>
+#include <device/pci_def.h>
+#include "pch.h"
+
+#define PCH_EHCI1_TEMP_BAR0 0xe8000000
+#define PCH_EHCI2_TEMP_BAR0 0xe8000400
+
+/*
+ * Setup USB controller MMIO BAR to prevent the
+ * reference code from resetting the controller.
+ *
+ * The BAR will be re-assigned during device
+ * enumeration so these are only temporary.
+ */
+void enable_usb_bar(void)
+{
+	device_t usb0 = PCH_EHCI1_DEV;
+	device_t usb1 = PCH_EHCI2_DEV;
+	u32 cmd;
+
+	/* USB Controller 1 */
+	pci_write_config32(usb0, PCI_BASE_ADDRESS_0,
+			   PCH_EHCI1_TEMP_BAR0);
+	cmd = pci_read_config32(usb0, PCI_COMMAND);
+	cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+	pci_write_config32(usb0, PCI_COMMAND, cmd);
+
+	/* USB Controller 1 */
+	pci_write_config32(usb1, PCI_BASE_ADDRESS_0,
+			   PCH_EHCI1_TEMP_BAR0);
+	cmd = pci_read_config32(usb1, PCI_COMMAND);
+	cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+	pci_write_config32(usb1, PCI_COMMAND, cmd);
+}