start of epia-m port

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1512 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

6 files changed, 537 insertions, 0 deletions

diff --git a/src/northbridge/via/vt8623/Config.lb b/src/northbridge/via/vt8623/Config.lb
new file mode 100644
index 0000000000..4a0c2c8658
--- /dev/null
+++ b/src/northbridge/via/vt8623/Config.lb
@@ -0,0 +1,2 @@
+config chip.h
+object northbridge.o
diff --git a/src/northbridge/via/vt8623/chip.h b/src/northbridge/via/vt8623/chip.h
new file mode 100644
index 0000000000..b689f0dedd
--- /dev/null
+++ b/src/northbridge/via/vt8623/chip.h
@@ -0,0 +1,5 @@
+struct northbridge_via_vt8601_config
+{
+};
+
+extern struct chip_control northbridge_via_vt8601_control;
diff --git a/src/northbridge/via/vt8623/northbridge.c b/src/northbridge/via/vt8623/northbridge.c
new file mode 100644
index 0000000000..5f5e5d9dd8
--- /dev/null
+++ b/src/northbridge/via/vt8623/northbridge.c
@@ -0,0 +1,122 @@
+#include <console/console.h>
+#include <arch/io.h>
+#include <stdint.h>
+#include <mem.h>
+#include <part/sizeram.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/hypertransport.h>
+#include <device/chip.h>
+#include <stdlib.h>
+#include <string.h>
+#include <bitops.h>
+#include "chip.h"
+#include "northbridge.h"
+
+static const uint8_t ramregs[] = {0x5a, 0x5b, 0x5c, 0x5d, 0x5e, 0x5f, 
+	  				0x56, 0x57};
+
+struct mem_range *sizeram(void)
+{
+	unsigned long mmio_basek;
+	static struct mem_range mem[10];
+	device_t dev;
+	int i, idx;
+	unsigned char rambits;
+
+	dev = dev_find_slot(0, 0);
+	if (!dev) {
+		printk_err("Cannot find PCI: 0:0\n");
+		return 0;
+	}
+	mem[0].basek = 0;
+	mem[0].sizek = 65536;
+	idx = 1;
+	while(idx < sizeof(mem)/sizeof(mem[0])) {
+		mem[idx].basek = 0;
+		mem[idx].sizek = 0;
+		idx++;
+	}
+	for(rambits = 0, i = 0; i < sizeof(ramregs)/sizeof(ramregs[0]); i++) {
+		unsigned char reg;
+		reg = pci_read_config8(dev, ramregs[i]);
+		/* these are ENDING addresses, not sizes. 
+		 * if there is memory in this slot, then reg will be > rambits.
+		 * So we just take the max, that gives us total. 
+		 * We take the highest one to cover for once and future linuxbios
+		 * bugs. We warn about bugs.
+		 */
+		if (reg > rambits)
+			rambits = reg;
+		if (reg < rambits)
+			printk_err("ERROR! register 0x%x is not set!\n", 
+				ramregs[i]);
+	}
+	
+	printk_debug("I would set ram size to 0x%x Kbytes\n", (rambits)*8*1024);
+	mem[0].sizek = rambits*8*1024;
+#if 1
+	for(i = 0; i < idx; i++) {
+		printk_debug("mem[%d].basek = %08x mem[%d].sizek = %08x\n",
+			i, mem[i].basek, i, mem[i].sizek);
+	}
+#endif
+
+	return mem;
+}
+static void enumerate(struct chip *chip)
+{
+	extern struct device_operations default_pci_ops_bus;
+	chip_enumerate(chip);
+	chip->dev->ops = &default_pci_ops_bus;
+}
+
+/*
+ * This fixup is based on capturing values from an Award bios.  Without
+ * this fixup the DMA write performance is awful (i.e. hdparm -t /dev/hda is 20x
+ * slower than normal, ethernet drops packets).
+ * Apparently these registers govern some sort of bus master behavior.
+ */
+static void random_fixup() {
+	device_t pcidev = dev_find_slot(0, 0);
+
+	printk_spew("VT8601 random fixup ...\n");
+	if (pcidev) {
+		pci_write_config8(pcidev, 0x70, 0xc0);
+		pci_write_config8(pcidev, 0x71, 0x88);
+		pci_write_config8(pcidev, 0x72, 0xec);
+		pci_write_config8(pcidev, 0x73, 0x0c);
+		pci_write_config8(pcidev, 0x74, 0x0e);
+		pci_write_config8(pcidev, 0x75, 0x81);
+		pci_write_config8(pcidev, 0x76, 0x52);
+	}
+}
+
+static void northbridge_init(struct chip *chip, enum chip_pass pass)
+{
+
+	struct northbridge_via_vt8601_config *conf = 
+		(struct northbridge_via_vt8601_config *)chip->chip_info;
+
+	switch (pass) {
+	case CONF_PASS_PRE_PCI:
+		break;
+		
+	case CONF_PASS_POST_PCI:
+		break;
+		
+	case CONF_PASS_PRE_BOOT:
+		random_fixup();
+		break;
+		
+	default:
+		/* nothing yet */
+		break;
+	}
+}
+
+struct chip_control northbridge_via_vt8601_control = {
+	.enumerate = enumerate,
+	.enable    = northbridge_init,
+	.name      = "VIA vt8601 Northbridge",
+};
diff --git a/src/northbridge/via/vt8623/northbridge.h b/src/northbridge/via/vt8623/northbridge.h
new file mode 100644
index 0000000000..d7f8e605b8
--- /dev/null
+++ b/src/northbridge/via/vt8623/northbridge.h
@@ -0,0 +1,6 @@
+#ifndef NORTHBRIDGE_VIA_VT8601_H
+#define NORTHBRIDGE_VIA_VT8601_H
+
+extern unsigned int vt8601_scan_root_bus(device_t root, unsigned int max);
+
+#endif /* NORTHBRIDGE_VIA_VT8601_H */
diff --git a/src/northbridge/via/vt8623/raminit.c b/src/northbridge/via/vt8623/raminit.c
new file mode 100644
index 0000000000..f295c9c737
--- /dev/null
+++ b/src/northbridge/via/vt8623/raminit.c
@@ -0,0 +1,394 @@
+#include <cpu/p6/mtrr.h>
+#include "raminit.h"
+
+/*
+This software and ancillary information (herein called SOFTWARE )
+called LinuxBIOS          is made available under the terms described
+here.  The SOFTWARE has been approved for release with associated
+LA-CC Number 00-34   .  Unless otherwise indicated, this SOFTWARE has
+been authored by an employee or employees of the University of
+California, operator of the Los Alamos National Laboratory under
+Contract No. W-7405-ENG-36 with the U.S. Department of Energy.  The
+U.S. Government has rights to use, reproduce, and distribute this
+SOFTWARE.  The public may copy, distribute, prepare derivative works
+and publicly display this SOFTWARE without charge, provided that this
+Notice and any statement of authorship are reproduced on all copies.
+Neither the Government nor the University makes any warranty, express 
+or implied, or assumes any liability or responsibility for the use of
+this SOFTWARE.  If SOFTWARE is modified to produce derivative works,
+such modified SOFTWARE should be clearly marked, so as not to confuse
+it with the version available from LANL.
+ */
+/* Copyright 2000, Ron Minnich, Advanced Computing Lab, LANL
+ * rminnich@lanl.gov
+ */
+/*
+ * 11/26/02 - kevinh@ispiri.com - The existing comments implied that
+ * this didn't work yet.  Therefore, I've updated it so that it works
+ * correctly - at least on my VIA epia motherboard.  64MB DIMM in slot 0.
+ */
+
+/* Added automatic detection of first equipped bank and its MA mapping type.
+ * (Rest of configuration is done in C)
+ * 5/19/03 by SONE Takeshi <ts1@tsn.or.jp>
+ */
+/* converted to C 9/2003 Ron Minnich */
+
+/* Set to 1 if your DIMMs are PC133 Note that I'm assuming CPU's FSB
+ * frequency is 133MHz. If your CPU runs at another bus speed, you
+ * might need to change some of register values.
+ */
+#ifndef DIMM_PC133
+#define DIMM_PC133 0
+#endif
+
+// Set to 1 if your DIMMs are CL=2
+#ifndef DIMM_CL2
+#define DIMM_CL2 0
+#endif
+
+void dimms_read(unsigned long x) 
+{
+	uint8_t c;
+	unsigned long eax; 
+	volatile unsigned long y;
+	eax =  x;
+	for(c = 0; c < 6; c++) {
+		y = * (volatile unsigned long *) eax;
+		eax += 0x10000000;
+	}
+}
+
+void dimms_write(int x) 
+{
+	uint8_t c;
+	unsigned long eax = x;
+	for(c = 0; c < 6; c++) {
+		*(volatile unsigned long *) eax = 0;
+		eax += 0x10000000;
+	}
+}
+
+
+
+#ifdef DEBUG_SETNORTHB
+void setnorthb(device_t north, uint8_t reg, uint8_t val) 
+{
+	print_debug("setnorth: reg ");
+	print_debug_hex8(reg);
+	print_debug(" to ");
+	print_debug_hex8(val);
+	print_debug("\r\n");
+	pci_write_config8(north, reg, val);
+}
+#else
+#define setnorthb pci_write_config8
+#endif
+
+void
+dumpnorth(device_t north) 
+{
+	uint8_t r, c;
+	for(r = 0; r < 256; r += 16) {
+		print_debug_hex8(r);
+		print_debug(":");
+		for(c = 0; c < 16; c++) {
+			print_debug_hex8(pci_read_config8(north, r+c));
+			print_debug(" ");
+		}
+		print_debug("\r\n");
+  }
+}
+
+static void sdram_set_registers(const struct mem_controller *ctrl) 
+{
+	device_t north = (device_t) 0;
+	uint8_t c, r;
+
+	print_err("vt8601 init starting\r\n");
+	north = pci_locate_device(PCI_ID(0x1106, 0x8601), 0);
+	north = 0;
+	print_debug_hex32(north);
+	print_debug(" is the north\n");
+	print_debug_hex16(pci_read_config16(north, 0));
+	print_debug(" ");
+	print_debug_hex16(pci_read_config16(north, 2));
+	print_debug("\r\n");
+	
+	/* All we are doing now is setting initial known-good values that will
+	 * be revised later as we read SPD
+	 */	
+	// memory clk enable. We are not using ECC
+	pci_write_config8(north,0x78, 0x01);
+	print_debug_hex8(pci_read_config8(north, 0x78));
+	// dram control, see the book. 
+#if DIMM_PC133
+	pci_write_config8(north,0x68, 0x52);
+#else
+	pci_write_config8(north,0x68, 0x42);
+#endif
+	// dram control, see the book. 
+	pci_write_config8(north,0x6B, 0x0c);
+	// Initial setting, 256MB in each bank, will be rewritten later.
+	pci_write_config8(north,0x5A, 0x20);
+	print_debug_hex8(pci_read_config8(north, 0x5a));
+	pci_write_config8(north,0x5B, 0x40);
+	pci_write_config8(north,0x5C, 0x60);
+	pci_write_config8(north,0x5D, 0x80);
+	pci_write_config8(north,0x5E, 0xA0);
+	pci_write_config8(north,0x5F, 0xC0);
+	// It seems we have to take care of these 2 registers as if 
+	// they are bank 6 and 7.
+	pci_write_config8(north,0x56, 0xC0);
+	pci_write_config8(north,0x57, 0xC0);
+	
+	// SDRAM in all banks
+	pci_write_config8(north,0x60, 0x3F);
+	// DRAM timing. I'm suspicious of this
+	// This is for all banks, 64 is 0,1.  65 is 2,3. 66 is 4,5.
+	// ras precharge 4T, RAS pulse 5T
+	// cas2 is 0xd6, cas3 is 0xe6
+	// we're also backing off write pulse width to 2T, so result is 0xee
+#if DIMM_CL2
+	pci_write_config8(north,0x64, 0xd4);
+	pci_write_config8(north,0x65, 0xd4);
+	pci_write_config8(north,0x66, 0xd4);
+#else // CL=3
+	pci_write_config8(north,0x64, 0xe4);
+	pci_write_config8(north,0x65, 0xe4);
+	pci_write_config8(north,0x66, 0xe4);
+#endif
+
+	// dram frequency select.
+	// enable 4K pages for 64M dram. 
+#if DIMM_PC133
+	pci_write_config8(north,0x69, 0x3c);
+#else
+	pci_write_config8(north,0x69, 0xac);
+#endif
+
+	/* IMPORTANT -- disable refresh counter */
+	// refresh counter, disabled.
+	pci_write_config8(north,0x6A, 0x00);
+	
+
+	// clkenable configuration. kevinh FIXME - add precharge
+	pci_write_config8(north,0x6C, 0x00);
+	// dram read latch delay of 1 ns, MD drive 8 mA,
+	// high drive strength on MA[2:	13], we#, cas#, ras#
+	// As per Cindy Lee, set to 0x37, not 0x57
+	pci_write_config8(north,0x6D, 0x7f);
+}
+
+/* slot is the dram slot. Return size of side0 in lower 16-bit,
+ * side1 in upper 16-bit, in units of 8MB */
+static unsigned long 
+spd_module_size(unsigned char slot) 
+{ 
+	/* for all the DRAMS, see if they are there and get the size of each
+	 * module. This is just a very early first cut at sizing.
+	 */
+	/* we may run out of registers ... */
+	unsigned int banks, rows, cols, reg;
+	unsigned int value = 0;
+	unsigned int module = ((0x50 + slot) << 1) + 1;
+	/* is the module there? if byte 2 is not 4, then we'll assume it 
+	 * is useless. 
+	 */
+	print_info("Slot "); 
+	print_info_hex8(slot); 
+	if (smbus_read_byte(module, 2) != 4) {
+		print_info(" is empty\r\n");
+		return 0;
+	}
+	print_info(" is SDRAM ");
+	
+	banks = smbus_read_byte(module, 17);
+	/* we're going to assume symmetric banks. Sorry. */
+	cols = smbus_read_byte(module, 4)  & 0xf;
+	rows = smbus_read_byte(module, 3)  & 0xf;
+	/* grand total. You have rows+cols addressing, * times of banks, times
+	 * width of data in bytes */
+	/* Width is assumed to be 64 bits == 8 bytes */
+	value = (1 << (cols + rows)) * banks * 8;
+	print_info_hex32(value);
+	print_info(" bytes ");
+	/* Return in 8MB units */
+	value >>= 23;
+
+	/* We should have single or double side */
+	if (smbus_read_byte(module, 5) == 2) {
+		print_info("x2");
+		value = (value << 16) | value;
+	}
+	print_info("\r\n");
+	return value;
+
+}
+
+static int
+spd_num_chips(unsigned char slot) 
+{ 
+	unsigned int module = ((0x50 + slot) << 1) + 1;
+	unsigned int width;
+
+	width = smbus_read_byte(module, 13);
+	if (width == 0)
+		width = 8;
+	return 64 / width;
+}
+
+static void sdram_set_spd_registers(const struct mem_controller *ctrl)
+{
+#define T133 7
+	unsigned char Trp = 1, Tras = 1, casl = 2, val;
+	unsigned char timing = 0xe4;
+	/* read Trp */
+	val = smbus_read_byte(0xa0, 27);
+	if (val < 2*T133)
+		Trp = 1;
+	val = smbus_read_byte(0xa0, 30);
+	if (val < 5*T133)
+		Tras = 0;
+	val = smbus_read_byte(0xa0, 18);
+	if (val < 8)
+		casl = 1;
+	if (val < 4)
+		casl = 0;
+	
+	val = (Trp << 7) | (Tras << 6) | (casl << 4) | 4;
+	
+	print_debug_hex8(val); print_debug(" is the computed timing\n");
+	/* don't set it. Experience shows that this screwy chipset should just
+	 * be run with the most conservative timing.
+	 * pci_write_config8(0, 0x64, val);
+	 */
+}
+
+static void set_ma_mapping(device_t north, int slot, int type)
+{
+    unsigned char reg, val;
+    int shift;
+
+    reg = 0x58 + slot/2;
+    if (slot%2 >= 1)
+        shift = 0;
+    else
+        shift = 4;
+
+    val = pci_read_config8(north, reg);
+    val &= ~(0xf << shift);
+    val |= type << shift;
+    pci_write_config8(north, reg, val);
+}
+
+
+static void sdram_enable(int controllers, const struct mem_controller *ctrl) 
+{
+	unsigned char i;
+	static const uint8_t ramregs[] = {
+		0x5a, 0x5b, 0x5c, 0x5d, 0x5e, 0x5f, 0x56, 0x57
+	};
+	device_t north = 0;
+	uint32_t size, base, slot, ma;
+	/* begin to initialize*/
+	// I forget why we need this, but we do
+	dimms_write(0xa55a5aa5);
+	
+	/* set NOP*/
+	pci_write_config8(north,0x6C, 0x01);
+	print_debug("NOP\r\n");
+	/* wait 200us*/
+	// You need to do the memory reference. That causes the nop cycle. 
+	dimms_read(0);
+	udelay(400);
+	print_debug("PRECHARGE\r\n");
+	/* set precharge */
+	pci_write_config8(north,0x6C, 0x02);
+	print_debug("DUMMY READS\r\n");
+	/* dummy reads*/
+	dimms_read(0);
+	udelay(200);
+	print_debug("CBR\r\n");
+	/* set CBR*/
+	pci_write_config8(north,0x6C, 0x04);
+	
+	/* do 8 reads and wait >100us between each - from via*/
+	dimms_read(0);
+	udelay(200);
+	dimms_read(0);
+	udelay(200);
+	dimms_read(0);
+	udelay(200);
+	dimms_read(0);
+	udelay(200);
+	dimms_read(0);
+	udelay(200);
+	dimms_read(0);
+	udelay(200);
+	dimms_read(0);
+	udelay(200);
+	dimms_read(0);
+	udelay(200);
+	print_debug("MRS\r\n");
+	/* set MRS*/
+	pci_write_config8(north,0x6c, 0x03);
+#if DIMM_CL2
+	dimms_read(0x150);
+#else // CL=3
+	dimms_read(0x1d0);
+#endif
+	udelay(200);
+	print_debug("NORMAL\r\n");
+	/* set to normal mode */
+	pci_write_config8(north,0x6C, 0x08);
+	
+	dimms_write(0x55aa55aa);
+	dimms_read(0);
+	udelay(200);
+	print_debug("set ref. rate\r\n");
+	// Set the refresh rate. 
+#if DIMM_PC133
+	pci_write_config8(north,0x6A, 0x86);
+#else
+	pci_write_config8(north,0x6A, 0x65);
+#endif
+	print_debug("enable multi-page open\r\n");
+	// enable multi-page open
+	pci_write_config8(north,0x6B, 0x0d);
+	
+	base = 0;
+	for(slot = 0; slot < 4; slot++) {
+		size = spd_module_size(slot);
+		/* side 0 */
+		base += size & 0xffff;
+		pci_write_config8(north, ramregs[2*slot], base);
+		/* side 1 */
+		base += size >> 16;
+		if (base > 0xff)
+			base = 0xff;
+		pci_write_config8(north, ramregs[2*slot + 1], base);
+
+		if (!size)
+			continue;
+
+		/* Calculate the value of MA mapping type register,
+		 * based on size of SDRAM chips. */
+		size = (size & 0xffff) << (3 + 3);
+			/* convert module size to be in Mbits */
+		size /= spd_num_chips(slot);
+		print_debug_hex16(size);
+		print_debug(" is the chip size\r\n");
+		if (size < 64)
+			ma = 0;
+		if (size < 256)
+			ma = 8;
+		else
+			ma = 0xe;
+		print_debug_hex16(ma);
+		print_debug(" is the MA type\r\n");
+		set_ma_mapping(north, slot, ma);
+	}
+	print_err("vt8601 done\r\n");
+	dumpnorth(north);
+}
diff --git a/src/northbridge/via/vt8623/raminit.h b/src/northbridge/via/vt8623/raminit.h
new file mode 100644
index 0000000000..b6d2339df3
--- /dev/null
+++ b/src/northbridge/via/vt8623/raminit.h
@@ -0,0 +1,8 @@
+#ifndef RAMINIT_H
+#define RAMINIT_H
+
+struct mem_controller {
+	int empty;
+};
+
+#endif /* RAMINIT_H */