*** empty log message ***

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

1 files changed, 214 insertions, 0 deletions

diff --git a/src/mainboard/tyan/s2735/Options.lb b/src/mainboard/tyan/s2735/Options.lb
new file mode 100644
index 0000000000..cecb58bb9f
--- /dev/null
+++ b/src/mainboard/tyan/s2735/Options.lb
@@ -0,0 +1,214 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses HARD_RESET_BUS
+uses HARD_RESET_DEVICE
+uses HARD_RESET_FUNCTION
+uses IRQ_SLOT_COUNT
+uses HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_LOGICAL_CPUS
+#uses CONFIG_MAX_PHYSICAL_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses FALLBACK_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses USE_OPTION_TABLE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+uses MAINBOARD
+uses LINUXBIOS_EXTRA_VERSION
+uses _RAMBASE
+uses CC
+uses HOSTCC
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_CONSOLE_SERIAL8250
+
+
+###
+### Build options
+###
+
+##
+## ROM_SIZE is the size of boot ROM that this board will use.
+##
+default ROM_SIZE=524288
+
+##
+## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+##
+default FALLBACK_SIZE=131072
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=1
+
+##
+## Funky hard reset implementation
+## 
+#default HARD_RESET_BUS=3
+#default HARD_RESET_DEVICE=4
+#default HARD_RESET_FUNCTION=0
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=15
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default HAVE_MP_TABLE=1
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=1
+
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_CPUS=4
+default CONFIG_LOGICAL_CPUS=1
+#default CONFIG_MAX_PHYSICAL_CPUS=2
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+default MAINBOARD_PART_NUMBER="Tyan"
+default MAINBOARD_VENDOR="s2735"
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+
+##
+## LinuxBIOS C code runs at this location in RAM
+##
+default _RAMBASE=0x00004000
+
+##
+## Load the payload from the ROM
+##
+default CONFIG_ROM_STREAM = 1
+
+###
+### Defaults of options that you may want to override in the target config file
+### 
+
+##
+## The default compiler
+##
+default CC="gcc"
+default HOSTCC="gcc"
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG      1   system is unusable               
+## ALERT      2   action must be taken immediately 
+## CRIT       3   critical conditions              
+## ERR        4   error conditions                 
+## WARNING    5   warning conditions               
+## NOTICE     6   normal but significant condition 
+## INFO       7   informational                    
+## DEBUG      8   debug-level messages             
+## SPEW       9   Way too many details             
+
+## Request this level of debugging output
+default  DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default  MAXIMUM_CONSOLE_LOGLEVEL=8
+
+##
+## Select power on after power fail setting
+default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+
+### End Options.lb
+end