cleanup due to failing tla-svn-sync

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1972 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

1 files changed, 0 insertions, 243 deletions

diff --git a/src/mainboard/tyan/s4880/Options.lb b/src/mainboard/tyan/s4880/Options.lb
deleted file mode 100644
index 42284e422d..0000000000
--- a/src/mainboard/tyan/s4880/Options.lb
+++ /dev/null
@@ -1,243 +0,0 @@
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HARD_RESET_BUS
-uses HARD_RESET_DEVICE
-uses HARD_RESET_FUNCTION
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
-uses CONFIG_MAX_CPUS
-uses CONFIG_MAX_PHYSICAL_CPUS
-uses CONFIG_LOGICAL_CPUS
-uses SERIAL_CPU_INIT
-uses CONFIG_IOAPIC
-uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses CONFIG_ROM_STREAM
-uses CONFIG_ROM_STREAM_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
-uses LINUXBIOS_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
-uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
-uses CC
-uses HOSTCC
-uses OBJCOPY
-uses CONFIG_CHIP_NAME
-uses CONFIG_CONSOLE_VGA
-uses CONFIG_PCI_ROM_RUN
-uses K8_E0_MEM_HOLE_SIZEK
-
-uses CONFIG_USE_INIT
-
-###
-### Build options
-###
-
-##
-## ROM_SIZE is the size of boot ROM that this board will use.
-##
-default ROM_SIZE=524288
-
-##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
-##
-default FALLBACK_SIZE=131072
-
-##
-## Build code for the fallback boot
-##
-default HAVE_FALLBACK_BOOT=1
-
-##
-## Build code to reset the motherboard from linuxBIOS
-##
-default HAVE_HARD_RESET=1
-
-##
-## Funky hard reset implementation
-## 
-default HARD_RESET_BUS=1
-default HARD_RESET_DEVICE=4
-default HARD_RESET_FUNCTION=0
-
-##
-## Build code to export a programmable irq routing table
-##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=22
-
-##
-## Build code to export an x86 MP table
-## Useful for specifying IRQ routing values
-##
-default HAVE_MP_TABLE=1
-
-##
-## Build code to export a CMOS option table
-##
-default HAVE_OPTION_TABLE=1
-
-##
-## Move the default LinuxBIOS cmos range off of AMD RTC registers
-##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
-
-##
-## Build code for SMP support
-## Only worry about 2 micro processors
-##
-default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=4
-default CONFIG_MAX_PHYSICAL_CPUS=4
-default CONFIG_LOGICAL_CPUS=0
-
-
-#default SERIAL_CPU_INIT=0
-
-#1G memory hole
-default K8_E0_MEM_HOLE_SIZEK=0x100000
-
-#VGA Console
-default CONFIG_CONSOLE_VGA=1
-default CONFIG_PCI_ROM_RUN=1
-
-##
-## Build code to setup a generic IOAPIC
-##
-default CONFIG_IOAPIC=1
-
-##
-## Clean up the motherboard id strings
-##
-default MAINBOARD_PART_NUMBER="s4880"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x4880
-
-###
-### LinuxBIOS layout values
-###
-
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
-default ROM_IMAGE_SIZE = 65536
-
-##
-## Use a small 8K stack
-##
-default STACK_SIZE=0x2000
-
-##
-## Use a small 16K heap
-##
-default HEAP_SIZE=0x4000
-
-##
-## Only use the option table in a normal image
-##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-
-##
-## LinuxBIOS C code runs at this location in RAM
-##
-default _RAMBASE=0x00004000
-
-##
-## Load the payload from the ROM
-##
-default CONFIG_ROM_STREAM = 1
-
-###
-### Defaults of options that you may want to override in the target config file
-### 
-
-##
-## The default compiler
-##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
-
-##
-## Disable the gdb stub by default
-## 
-default CONFIG_GDB_STUB=0
-
-##
-## The Serial Console
-##
-
-# To Enable the Serial Console
-default CONFIG_CONSOLE_SERIAL8250=1
-
-## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
-
-# Select the serial console base port
-default TTYS0_BASE=0x3f8
-
-# Select the serial protocol
-# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
-
-##
-### Select the linuxBIOS loglevel
-##
-## EMERG      1   system is unusable               
-## ALERT      2   action must be taken immediately 
-## CRIT       3   critical conditions              
-## ERR        4   error conditions                 
-## WARNING    5   warning conditions               
-## NOTICE     6   normal but significant condition 
-## INFO       7   informational                    
-## DEBUG      8   debug-level messages             
-## SPEW       9   Way too many details             
-
-## Request this level of debugging output
-default  DEFAULT_CONSOLE_LOGLEVEL=8
-## At a maximum only compile in this level of debugging
-default  MAXIMUM_CONSOLE_LOGLEVEL=8
-
-##
-## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
-
-### End Options.lb
-end