khepri resource map update to keep compatibility chain

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1129 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

2 files changed, 274 insertions, 13 deletions

diff --git a/src/mainboard/newisys/khepri/auto.c b/src/mainboard/newisys/khepri/auto.c
index 21c12345b7..3d28fa728d 100644
--- a/src/mainboard/newisys/khepri/auto.c
+++ b/src/mainboard/newisys/khepri/auto.c
@@ -102,6 +102,8 @@ static void coherent_ht_mainboard(unsigned cpus)
 #include "northbridge/amd/amdk8/coherent_ht.c"
 #include "sdram/generic_sdram.c"
 
+#include "resourcemap.c" /* newisys khepri does not want the default */
+
 static void enable_lapic(void)
 {
 
@@ -155,9 +157,6 @@ static void pc87360_enable_serial(void)
 	pnp_set_iobase0(SIO_BASE, 0x3f8);
 }
 
-#define FIRST_CPU  1
-#define SECOND_CPU 0
-#define TOTAL_CPUS (FIRST_CPU + SECOND_CPU)
 static void main(void)
 {
 	/*
@@ -165,7 +164,6 @@ static void main(void)
 	 * GPIO29 of 8111 will control H1_MEMRESET_L
 	 */
 	static const struct mem_controller cpu[] = {
-#if FIRST_CPU
 		{
 			.node_id = 0,
 			.f0 = PCI_DEV(0, 0x18, 0),
@@ -175,8 +173,6 @@ static void main(void)
 			.channel0 = { (0xa<<3)|0, (0xa<<3)|2, 0, 0 },
 			.channel1 = { (0xa<<3)|1, (0xa<<3)|3, 0, 0 },
 		},
-#endif
-#if SECOND_CPU
 		{
 			.node_id = 1,
 			.f0 = PCI_DEV(0, 0x19, 0),
@@ -186,7 +182,6 @@ static void main(void)
 			.channel0 = { (0xa<<3)|4, (0xa<<3)|6, 0, 0 },
 			.channel1 = { (0xa<<3)|5, (0xa<<3)|7, 0, 0 },
 		},
-#endif
 	};
 	if (cpu_init_detected()) {
 		asm("jmp __cpu_reset");
@@ -199,7 +194,7 @@ static void main(void)
 	pc87360_enable_serial();
 	uart_init();
 	console_init();
-	setup_default_resource_map();
+	setup_khepri_resource_map();
 	setup_coherent_ht_domain();
 	enumerate_ht_chain(0);
 	distinguish_cpu_resets(0);
@@ -233,12 +228,7 @@ static void main(void)
 #if 0
 	ram_check(0x00000000, msr.lo);
 #else
-#if TOTAL_CPUS < 2
 	/* Check 16MB of memory @ 0*/
 	ram_check(0x00000000, 0x01000);
-#else
-	/* Check 16MB of memory @ 2GB */
-	ram_check(0x80000000, 0x81000000);
-#endif
 #endif
 }
diff --git a/src/mainboard/newisys/khepri/resourcemap.c b/src/mainboard/newisys/khepri/resourcemap.c
new file mode 100644
index 0000000000..ccc163210e
--- /dev/null
+++ b/src/mainboard/newisys/khepri/resourcemap.c
@@ -0,0 +1,271 @@
+/*
+ * Resource map for Newisys Khepri
+ *
+ */
+
+#define LDT0 0
+#define LDT1 1
+#define LDT2 2
+
+/* Khepri has the I/O hub connected to Link1 */
+#define SB_LINK LDT1
+
+static void setup_khepri_resource_map(void)
+{
+	static const unsigned int register_values[] = {
+	/* Careful set limit registers before base registers which contain the enables */
+	/* DRAM Limit i Registers
+	 * F1:0x44 i = 0
+	 * F1:0x4C i = 1
+	 * F1:0x54 i = 2
+	 * F1:0x5C i = 3
+	 * F1:0x64 i = 4
+	 * F1:0x6C i = 5
+	 * F1:0x74 i = 6
+	 * F1:0x7C i = 7
+	 * [ 2: 0] Destination Node ID
+	 *	   000 = Node 0
+	 *	   001 = Node 1
+	 *	   010 = Node 2
+	 *	   011 = Node 3
+	 *	   100 = Node 4
+	 *	   101 = Node 5
+	 *	   110 = Node 6
+	 *	   111 = Node 7
+	 * [ 7: 3] Reserved
+	 * [10: 8] Interleave select
+	 *	   specifies the values of A[14:12] to use with interleave enable.
+	 * [15:11] Reserved
+	 * [31:16] DRAM Limit Address i Bits 39-24
+	 *	   This field defines the upper address bits of a 40 bit  address
+	 *	   that define the end of the DRAM region.
+	 */
+	PCI_ADDR(0, 0x18, 1, 0x44), 0x0000f8f8, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x4C), 0x0000f8f8, 0x00000001,
+	PCI_ADDR(0, 0x18, 1, 0x54), 0x0000f8f8, 0x00000002,
+	PCI_ADDR(0, 0x18, 1, 0x5C), 0x0000f8f8, 0x00000003,
+	PCI_ADDR(0, 0x18, 1, 0x64), 0x0000f8f8, 0x00000004,
+	PCI_ADDR(0, 0x18, 1, 0x6C), 0x0000f8f8, 0x00000005,
+	PCI_ADDR(0, 0x18, 1, 0x74), 0x0000f8f8, 0x00000006,
+	PCI_ADDR(0, 0x18, 1, 0x7C), 0x0000f8f8, 0x00000007,
+	/* DRAM Base i Registers
+	 * F1:0x40 i = 0
+	 * F1:0x48 i = 1
+	 * F1:0x50 i = 2
+	 * F1:0x58 i = 3
+	 * F1:0x60 i = 4
+	 * F1:0x68 i = 5
+	 * F1:0x70 i = 6
+	 * F1:0x78 i = 7
+	 * [ 0: 0] Read Enable
+	 *	   0 = Reads Disabled
+	 *	   1 = Reads Enabled
+	 * [ 1: 1] Write Enable
+	 *	   0 = Writes Disabled
+	 *	   1 = Writes Enabled
+	 * [ 7: 2] Reserved
+	 * [10: 8] Interleave Enable
+	 *	   000 = No interleave
+	 *	   001 = Interleave on A[12] (2 nodes)
+	 *	   010 = reserved
+	 *	   011 = Interleave on A[12] and A[14] (4 nodes)
+	 *	   100 = reserved
+	 *	   101 = reserved
+	 *	   110 = reserved
+	 *	   111 = Interleve on A[12] and A[13] and A[14] (8 nodes)
+	 * [15:11] Reserved
+	 * [13:16] DRAM Base Address i Bits 39-24
+	 *	   This field defines the upper address bits of a 40-bit address
+	 *	   that define the start of the DRAM region.
+	 */
+	PCI_ADDR(0, 0x18, 1, 0x40), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x48), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x50), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x58), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x60), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x68), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x70), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x78), 0x0000f8fc, 0x00000000,
+
+	/* Memory-Mapped I/O Limit i Registers
+	 * F1:0x84 i = 0
+	 * F1:0x8C i = 1
+	 * F1:0x94 i = 2
+	 * F1:0x9C i = 3
+	 * F1:0xA4 i = 4
+	 * F1:0xAC i = 5
+	 * F1:0xB4 i = 6
+	 * F1:0xBC i = 7
+	 * [ 2: 0] Destination Node ID
+	 *	   000 = Node 0
+	 *	   001 = Node 1
+	 *	   010 = Node 2
+	 *	   011 = Node 3
+	 *	   100 = Node 4
+	 *	   101 = Node 5
+	 *	   110 = Node 6
+	 *	   111 = Node 7
+	 * [ 3: 3] Reserved
+	 * [ 5: 4] Destination Link ID
+	 *	   00 = Link 0
+	 *	   01 = Link 1
+	 *	   10 = Link 2
+	 *	   11 = Reserved
+	 * [ 6: 6] Reserved
+	 * [ 7: 7] Non-Posted
+	 *	   0 = CPU writes may be posted
+	 *	   1 = CPU writes must be non-posted
+	 * [31: 8] Memory-Mapped I/O Limit Address i (39-16)
+	 *	   This field defines the upp adddress bits of a 40-bit address that
+	 *	   defines the end of a memory-mapped I/O region n
+	 */
+	PCI_ADDR(0, 0x18, 1, 0x84), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x8C), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x94), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x9C), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xA4), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xAC), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xB4), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xBC), 0x00000048, 0x00ffff00 | (SB_LINK<<4),
+
+	/* Memory-Mapped I/O Base i Registers
+	 * F1:0x80 i = 0
+	 * F1:0x88 i = 1
+	 * F1:0x90 i = 2
+	 * F1:0x98 i = 3
+	 * F1:0xA0 i = 4
+	 * F1:0xA8 i = 5
+	 * F1:0xB0 i = 6
+	 * F1:0xB8 i = 7
+	 * [ 0: 0] Read Enable
+	 *	   0 = Reads disabled
+	 *	   1 = Reads Enabled
+	 * [ 1: 1] Write Enable
+	 *	   0 = Writes disabled
+	 *	   1 = Writes Enabled
+	 * [ 2: 2] Cpu Disable
+	 *	   0 = Cpu can use this I/O range
+	 *	   1 = Cpu requests do not use this I/O range
+	 * [ 3: 3] Lock
+	 *	   0 = base/limit registers i are read/write
+	 *	   1 = base/limit registers i are read-only
+	 * [ 7: 4] Reserved
+	 * [31: 8] Memory-Mapped I/O Base Address i (39-16)
+	 *	   This field defines the upper address bits of a 40bit address 
+	 *	   that defines the start of memory-mapped I/O region i
+	 */
+	PCI_ADDR(0, 0x18, 1, 0x80), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x88), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x90), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x98), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xA0), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xA8), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xB0), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xB8), 0x000000f0, 0x00fc0003,
+
+	/* PCI I/O Limit i Registers
+	 * F1:0xC4 i = 0
+	 * F1:0xCC i = 1
+	 * F1:0xD4 i = 2
+	 * F1:0xDC i = 3
+	 * [ 2: 0] Destination Node ID
+	 *	   000 = Node 0
+	 *	   001 = Node 1
+	 *	   010 = Node 2
+	 *	   011 = Node 3
+	 *	   100 = Node 4
+	 *	   101 = Node 5
+	 *	   110 = Node 6
+	 *	   111 = Node 7
+	 * [ 3: 3] Reserved
+	 * [ 5: 4] Destination Link ID
+	 *	   00 = Link 0
+	 *	   01 = Link 1
+	 *	   10 = Link 2
+	 *	   11 = reserved
+	 * [11: 6] Reserved
+	 * [24:12] PCI I/O Limit Address i
+	 *	   This field defines the end of PCI I/O region n
+	 * [31:25] Reserved
+	 */
+	PCI_ADDR(0, 0x18, 1, 0xC4), 0xFE000FC8, 0x01fff000 | (SB_LINK<<4),
+	PCI_ADDR(0, 0x18, 1, 0xCC), 0xFE000FC8, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xD4), 0xFE000FC8, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xDC), 0xFE000FC8, 0x00000000,
+
+	/* PCI I/O Base i Registers
+	 * F1:0xC0 i = 0
+	 * F1:0xC8 i = 1
+	 * F1:0xD0 i = 2
+	 * F1:0xD8 i = 3
+	 * [ 0: 0] Read Enable
+	 *	   0 = Reads Disabled
+	 *	   1 = Reads Enabled
+	 * [ 1: 1] Write Enable
+	 *	   0 = Writes Disabled
+	 *	   1 = Writes Enabled
+	 * [ 3: 2] Reserved
+	 * [ 4: 4] VGA Enable
+	 *	   0 = VGA matches Disabled
+	 *	   1 = matches all address < 64K and where A[9:0] is in the 
+	 *	       range 3B0-3BB or 3C0-3DF independen of the base & limit registers
+	 * [ 5: 5] ISA Enable
+	 *	   0 = ISA matches Disabled
+	 *	   1 = Blocks address < 64K and in the last 768 bytes of eack 1K block
+	 *	       from matching agains this base/limit pair
+	 * [11: 6] Reserved
+	 * [24:12] PCI I/O Base i
+	 *	   This field defines the start of PCI I/O region n 
+	 * [31:25] Reserved
+	 */
+	PCI_ADDR(0, 0x18, 1, 0xC0), 0xFE000FCC, 0x00000003,
+	PCI_ADDR(0, 0x18, 1, 0xC8), 0xFE000FCC, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xD0), 0xFE000FCC, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xD8), 0xFE000FCC, 0x00000000,
+
+	/* Config Base and Limit i Registers
+	 * F1:0xE0 i = 0
+	 * F1:0xE4 i = 1
+	 * F1:0xE8 i = 2
+	 * F1:0xEC i = 3
+	 * [ 0: 0] Read Enable
+	 *	   0 = Reads Disabled
+	 *	   1 = Reads Enabled
+	 * [ 1: 1] Write Enable
+	 *	   0 = Writes Disabled
+	 *	   1 = Writes Enabled
+	 * [ 2: 2] Device Number Compare Enable
+	 *	   0 = The ranges are based on bus number
+	 *	   1 = The ranges are ranges of devices on bus 0
+	 * [ 3: 3] Reserved
+	 * [ 6: 4] Destination Node
+	 *	   000 = Node 0
+	 *	   001 = Node 1
+	 *	   010 = Node 2
+	 *	   011 = Node 3
+	 *	   100 = Node 4
+	 *	   101 = Node 5
+	 *	   110 = Node 6
+	 *	   111 = Node 7
+	 * [ 7: 7] Reserved
+	 * [ 9: 8] Destination Link
+	 *	   00 = Link 0
+	 *	   01 = Link 1
+	 *	   10 = Link 2
+	 *	   11 - Reserved
+	 * [15:10] Reserved
+	 * [23:16] Bus Number Base i
+	 *	   This field defines the lowest bus number in configuration region i
+	 * [31:24] Bus Number Limit i
+	 *	   This field defines the highest bus number in configuration regin i
+	 */
+	PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0xff000003,
+	PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0x00000000,
+	};
+	int max;
+	max = sizeof(register_values)/sizeof(register_values[0]);
+	setup_resource_map(register_values, max);
+}
+