mb/*/*: use ACPIMMIO common block wherever possible

TEST=boot PC Engines apu2 and launch Debian Linux

Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I648167ec94367c9494c4253bec21dab20ad7b615
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>

1 files changed, 39 insertions, 29 deletions

diff --git a/src/mainboard/lippert/frontrunner-af/mainboard.c b/src/mainboard/lippert/frontrunner-af/mainboard.c
index 6ad5234d81..9e3eab7a6c 100644
--- a/src/mainboard/lippert/frontrunner-af/mainboard.c
+++ b/src/mainboard/lippert/frontrunner-af/mainboard.c
@@ -59,32 +59,41 @@ static const u16 sio_init_table[] = { // hi = offset, lo = value
 
 static void init(struct device *dev)
 {
-	volatile u8 *spi_base;	// base addr of Hudson's SPI host controller
+	volatile u8 *spi_base;	/* base addr of Hudson's SPI host controller */
 	int i;
 	printk(BIOS_DEBUG, CONFIG_MAINBOARD_PART_NUMBER " ENTER %s\n", __func__);
 
 	/* Init Hudson GPIOs. */
 	printk(BIOS_DEBUG, "Init FCH GPIOs @ 0x%08x\n", ACPI_MMIO_BASE+GPIO_BASE);
-	FCH_IOMUX(50) = 2;    // GPIO50: FCH_ARST#_GATE resets stuck PCIe devices
-	FCH_GPIO (50) = 0xC0; // = output set to 1 as it's never needed
-	FCH_IOMUX(197) = 2;    // GPIO197: BIOS_DEFAULTS# = input (int. PU)
-	FCH_IOMUX(56) = 1;    // GPIO58-56: REV_ID2-0
-	FCH_GPIO (56) = 0x28; // = inputs, disable int. pull-ups
-	FCH_IOMUX(57) = 1;
-	FCH_GPIO (57) = 0x28;
-	FCH_IOMUX(58) = 1;
-	FCH_GPIO (58) = 0x28;
-	FCH_IOMUX(96) = 1;    // "Gpio96": GEVENT0# signal on X2 connector (int. PU)
-	FCH_IOMUX(52) = 1;    // GPIO52,61,62,187-192 free to use on X2 connector
-	FCH_IOMUX(61) = 2;    // default to inputs with int. PU
-	FCH_IOMUX(62) = 2;
-	FCH_IOMUX(187) = 2;
-	FCH_IOMUX(188) = 2;
-	FCH_IOMUX(189) = 1;
-	FCH_IOMUX(190) = 1;
-	FCH_IOMUX(191) = 1;
-	FCH_IOMUX(192) = 1;
-	if (!fch_gpio_state(197)) // just in case anyone cares
+	/* GPIO50: FCH_ARST#_GATE resets stuck PCIe devices */
+	iomux_write8(50, 2);
+	/* output set to 1 as it's never needed */
+	iomux_write8(50, 0xc0);
+	/* GPIO197: BIOS_DEFAULTS# = input (int. PU) */
+	iomux_write8(197, 2);
+	/* GPIO58-56: REV_ID2-0 */
+	iomux_write8(56, 1);
+	/* inputs, disable int. pull-ups */
+	gpio_100_write8(56, 0x28);
+	iomux_write8(57, 1);
+	gpio_100_write8(57, 0x28);
+	iomux_write8(58, 1);
+	gpio_100_write8(58, 0x28);
+	/* "Gpio96": GEVENT0# signal on X2 connector (int. PU) */
+	iomux_write8(96, 1);
+	/* GPIO52,61,62,187-192 free to use on X2 connector */
+	iomux_write8(52, 1);
+	/* default to inputs with int. PU */
+	iomux_write8(61, 2);
+	iomux_write8(62, 2);
+	iomux_write8(187, 2);
+	iomux_write8(188, 2);
+	iomux_write8(189, 1);
+	iomux_write8(190, 1);
+	iomux_write8(191, 1);
+	iomux_write8(192, 1);
+	/* just in case anyone cares */
+	if (!fch_gpio_state(197))
 		printk(BIOS_INFO, "BIOS_DEFAULTS jumper is present.\n");
 	printk(BIOS_INFO, "Board revision ID: %u\n",
 	       fch_gpio_state(58)<<2 | fch_gpio_state(57)<<1 | fch_gpio_state(56));
@@ -99,9 +108,11 @@ static void init(struct device *dev)
 	/* Lower SPI speed from default 66 to 22 MHz for SST 25VF032B */
 	spi_base = (u8 *)((uintptr_t)pci_read_config32(pcidev_on_root(0x14, 3),
 							   0xA0) & 0xFFFFFFE0);
-	spi_base[0x0D] = (spi_base[0x0D] & ~0x30) | 0x20; // NormSpeed in SPI_Cntrl1 register
+	/* NormSpeed in SPI_Cntrl1 register */
+	spi_base[0x0D] = (spi_base[0x0D] & ~0x30) | 0x20;
 
-	/* Notify the SMC we're alive and kicking, or after a while it will
+	/*
+	 * Notify the SMC we're alive and kicking, or after a while it will
 	 * effect a power cycle and switch to the alternate BIOS chip.
 	 * Should be done as late as possible.
 	 * Failure here does not matter if watchdog was already disabled,
@@ -122,12 +133,11 @@ static void mainboard_enable(struct device *dev)
 
 	/* enable GPP CLK0 */
 	/* disable GPP CLK1 thru SLT_GFX_CLK */
-	u8 *misc_mem_clk_cntrl = (u8 *)(ACPI_MMIO_BASE + MISC_BASE);
-	write8(misc_mem_clk_cntrl + 0, 0x0F);
-	write8(misc_mem_clk_cntrl + 1, 0x00);
-	write8(misc_mem_clk_cntrl + 2, 0x00);
-	write8(misc_mem_clk_cntrl + 3, 0x00);
-	write8(misc_mem_clk_cntrl + 4, 0x00);
+	misc_write8(0, 0x0f);
+	misc_write8(1, 0);
+	misc_write8(2, 0);
+	misc_write8(3, 0);
+	misc_write8(4, 0);
 
 	/*
 	 * Initialize ASF registers to an arbitrary address because someone