diff options
author | Furquan Shaikh <furquan@google.com> | 2020-06-22 10:45:12 -0700 |
---|---|---|
committer | Furquan Shaikh <furquan@google.com> | 2020-06-25 08:08:37 +0000 |
commit | 8302585c152926c086107cdf11f48040d0d873d5 (patch) | |
tree | 8d1d1aaa91797d16e5e6e47e7831558d0a52b5b6 /src/mainboard/google/zork/variants/baseboard/gpio_baseboard_trembyle.c | |
parent | 462f3ed111e049cc95e2ee2ce4f4e88a415cc912 (diff) |
mb/google/zork: Add support for WiFi power sequencing
This change replaces variant_wifi_romstage_gpio_table() with
variant_pcie_power_reset_configure() to handle the reset and power
sequencing for WiFi devices pre- and post- v3 version of schematics.
These are the requirements that need to be satisfied:
1. As per PCI Express M.2 Specification Revision 3.0,
Version 1.2, Section 3.1.4 "Power-up Timing", PERST# should stay
disabled until `TPVPGL` time duration after device power has
stabilized. Value of TPVPGL is implementation specific.
2. For Intel WiFi chip, it is known to get into a bad state if the
above requirement is violated and hence requires a power cycle.
3. On pre-v3 schematics:
- For both dalboz and trembyle references, GPIO42 drives
WIFI_AUX_RESET_L which is pulled up to PP3300_WIFI.
- For both dalboz and trembyle references, PP3300_WIFI is controlled
using GPIO29. This pad gets pulled high by default on PWRGOOD
because of internal pull-up. But, at RESET# it is known to have a
glitch. When GPIO29 gets pulled high, it causes WIFI_AUX_RESET_L to
be pulled high as well. This violates the PCIe power sequencing
requirements. Hence, for pre-v3 schematics on both dalboz and
trembyle, following sequence needs to be followed:
a. Assert WIFI_AUX_RESET_L.
b. Disable power to WiFi.
c. Wait 10ms to allow WiFi power to go low.
d. Enable power to WiFi.
e. Wait 50ms as per PCIe specification.
f. Deassert WIFI_AUX_RESET_L.
4. On v3 schematics:
- For trembyle: WIFI_AUX_RESET_L is driven by GPIO86 which has an
internal PU as well as an external PU to PP3300_WIFI.
- For dalboz: WIFI_AUX_RESET is driven by GPIO29. This is active
high and has an internal PU. It also has an external 1K PD to
overcome internal PU.
- For both dalboz and trembyle references, PP3300_WIFI is
controlled by GPIO42 which has an internal PU and external
PD. Trembyle schematics have a comment saying strong PD of 2.2K but
the stuffed resistor is a weak one (499K). ON dalboz, it uses a
weak PD (which doesn't look correct and instead should be a strong
PD just like trembyle). Having a strong PD ensures that the WiFi
power is kept disabled when coming out of G3 until coreboot
configures GPIO42 as high.
- Thus, for v3 schematics, following sequence needs to be followed:
a. Assert WIFI_AUX_RESET{_L} signal.
b. Enable power to WiFi.
c. Wait 50ms as per PCIe specification.
d. Deassert WIFI_AUX_RESET{_L} signal.
BUG=b:157686402, b:158257076
TEST=Verified that QCA and AX200 cards both continue working. Tested
QCA on Dalboz and Trembyle. Tested AX200 on morphius.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I532131ee911d5efb5130d8710f3e01578f6c9627
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42738
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Diffstat (limited to 'src/mainboard/google/zork/variants/baseboard/gpio_baseboard_trembyle.c')
-rw-r--r-- | src/mainboard/google/zork/variants/baseboard/gpio_baseboard_trembyle.c | 89 |
1 files changed, 60 insertions, 29 deletions
diff --git a/src/mainboard/google/zork/variants/baseboard/gpio_baseboard_trembyle.c b/src/mainboard/google/zork/variants/baseboard/gpio_baseboard_trembyle.c index d3f7ae3454..3f02f00e25 100644 --- a/src/mainboard/google/zork/variants/baseboard/gpio_baseboard_trembyle.c +++ b/src/mainboard/google/zork/variants/baseboard/gpio_baseboard_trembyle.c @@ -1,6 +1,8 @@ /* SPDX-License-Identifier: GPL-2.0-or-later */ #include <baseboard/variants.h> +#include <delay.h> +#include <gpio.h> #include <soc/gpio.h> #include <soc/smi.h> #include <stdlib.h> @@ -20,8 +22,6 @@ static const struct soc_amd_gpio gpio_set_stage_rom_pre_v3[] = { PAD_NF(GPIO_27, PCIE_RST1_L, PULL_NONE), /* NVME_AUX_RESET_L */ PAD_GPO(GPIO_40, HIGH), - /* WIFI_AUX_RESET_L */ - PAD_GPO(GPIO_42, HIGH), /* EN_PWR_TOUCHPAD_PS2 - reset */ PAD_GPO(GPIO_67, LOW), /* EMMC_RESET - reset (default stuffing unused)*/ @@ -42,11 +42,6 @@ static const struct soc_amd_gpio gpio_set_stage_rom_pre_v3[] = { PAD_GPO(GPIO_142, HIGH), }; -static const struct soc_amd_gpio gpio_set_wifi_pre_v3[] = { - /* EN_PWR_WIFI */ - PAD_GPO(GPIO_29, HIGH), -}; - static const struct soc_amd_gpio gpio_set_stage_rom_v3[] = { /* PEN_POWER_EN - reset */ PAD_GPO(GPIO_5, LOW), @@ -66,8 +61,6 @@ static const struct soc_amd_gpio gpio_set_stage_rom_v3[] = { PAD_GPO(GPIO_68, HIGH), /* EN_PWR_CAMERA - reset */ PAD_GPO(GPIO_76, LOW), - /* WIFI_AUX_RESET_L */ - PAD_GPO(GPIO_86, HIGH), /* CLK_REQ0_L - WIFI */ PAD_NF(GPIO_92, CLK_REQ0_L, PULL_UP), /* CLK_REQ1_L - SD Card */ @@ -82,11 +75,6 @@ static const struct soc_amd_gpio gpio_set_stage_rom_v3[] = { PAD_GPO(GPIO_142, HIGH), }; -static const struct soc_amd_gpio gpio_set_wifi_v3[] = { - /* EN_PWR_WIFI */ - PAD_GPO(GPIO_42, HIGH), -}; - static const struct soc_amd_gpio gpio_set_stage_ram[] = { /* PWR_BTN_L */ @@ -214,21 +202,6 @@ struct soc_amd_gpio *variant_romstage_gpio_table(size_t *size) } const __weak -struct soc_amd_gpio *variant_wifi_romstage_gpio_table(size_t *size) -{ - uint32_t board_version; - - if (!google_chromeec_cbi_get_board_version(&board_version) && - (board_version >= CONFIG_VARIANT_MIN_BOARD_ID_V3_SCHEMATICS)) { - *size = ARRAY_SIZE(gpio_set_wifi_v3); - return gpio_set_wifi_v3; - } - - *size = ARRAY_SIZE(gpio_set_wifi_pre_v3); - return gpio_set_wifi_pre_v3; -} - -const __weak struct soc_amd_gpio *variant_base_gpio_table(size_t *size) { *size = ARRAY_SIZE(gpio_set_stage_ram); @@ -246,3 +219,61 @@ const __weak struct sci_source *get_gpe_table(size_t *num) { return NULL; } + +static void wifi_power_reset_configure_v3(void) +{ + /* + * Configure WiFi GPIOs such that: + * - WIFI_AUX_RESET_L is configured first to assert PERST# to WiFi device. + * - Enable power to WiFi using EN_PWR_WIFI. + * - Wait for 50ms after power to WiFi is enabled. + * - Deassert WIFI_AUX_RESET_L. + */ + static const struct soc_amd_gpio v3_wifi_table[] = { + /* WIFI_AUX_RESET_L */ + PAD_GPO(GPIO_86, LOW), + /* EN_PWR_WIFI */ + PAD_GPO(GPIO_42, HIGH), + }; + program_gpios(v3_wifi_table, ARRAY_SIZE(v3_wifi_table)); + + mdelay(50); + gpio_set(GPIO_86, 1); +} + +static void wifi_power_reset_configure_pre_v3(void) +{ + /* + * Configure WiFi GPIOs such that: + * - WIFI_AUX_RESET_L is configured first to assert PERST# to WiFi device. + * - Disable power to WiFi since GPIO_29 goes high on PWRGOOD but has a glitch on RESET# + * deassertion causing WiFi to enter a bad state. + * - Wait 10ms for WiFi power to go low. + * - Enable power to WiFi using EN_PWR_WIFI. + * - Wait for 50ms after power to WiFi is enabled. + * - Deassert WIFI_AUX_RESET_L. + */ + static const struct soc_amd_gpio pre_v3_wifi_table[] = { + /* WIFI_AUX_RESET_L */ + PAD_GPO(GPIO_42, LOW), + /* EN_PWR_WIFI */ + PAD_GPO(GPIO_29, LOW), + }; + program_gpios(pre_v3_wifi_table, ARRAY_SIZE(pre_v3_wifi_table)); + + mdelay(10); + gpio_set(GPIO_29, 1); + mdelay(50); + gpio_set(GPIO_42, 1); +} + +__weak void variant_pcie_power_reset_configure(void) +{ + uint32_t board_version; + + if (!google_chromeec_cbi_get_board_version(&board_version) && + (board_version >= CONFIG_VARIANT_MIN_BOARD_ID_V3_SCHEMATICS)) + wifi_power_reset_configure_v3(); + else + wifi_power_reset_configure_pre_v3(); +} |