sc7180: Add support for sn65dsi86 bridge

Add sn65dsi86 bridge driver to enable the eDP bridge.
Datasheet used : https://www.ti.com/lit/ds/sllseh2b/sllseh2b.pdf

Changes in V1:
- fix the dp lanes using mask
- separate out the refclk and hpd config to init function

Change-Id: I36a68f3241f0ba316c261a73c2f6d30fe6c3ccdc
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>

4 files changed, 546 insertions, 0 deletions

diff --git a/src/drivers/ti/sn65dsi86bridge/Kconfig b/src/drivers/ti/sn65dsi86bridge/Kconfig
new file mode 100644
index 0000000000..b7abb34231
--- /dev/null
+++ b/src/drivers/ti/sn65dsi86bridge/Kconfig
@@ -0,0 +1,7 @@
+## SPDX-License-Identifier: GPL-2.0-only
+
+config DRIVERS_TI_SN65DSI86BRIDGE
+	bool
+	default n
+	help
+	  TI SN65DSI86 eDP bridge driver
diff --git a/src/drivers/ti/sn65dsi86bridge/Makefile.inc b/src/drivers/ti/sn65dsi86bridge/Makefile.inc
new file mode 100644
index 0000000000..b146fe363c
--- /dev/null
+++ b/src/drivers/ti/sn65dsi86bridge/Makefile.inc
@@ -0,0 +1,3 @@
+## SPDX-License-Identifier: GPL-2.0-only
+
+ramstage-$(CONFIG_DRIVERS_TI_SN65DSI86BRIDGE) += sn65dsi86bridge.c
diff --git a/src/drivers/ti/sn65dsi86bridge/sn65dsi86bridge.c b/src/drivers/ti/sn65dsi86bridge/sn65dsi86bridge.c
new file mode 100644
index 0000000000..e0058c4fe7
--- /dev/null
+++ b/src/drivers/ti/sn65dsi86bridge/sn65dsi86bridge.c
@@ -0,0 +1,514 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <console/console.h>
+#include <delay.h>
+#include <endian.h>
+#include <device/i2c_simple.h>
+#include <edid.h>
+#include <timer.h>
+#include <types.h>
+#include <soc/addressmap.h>
+#include "sn65dsi86bridge.h"
+
+#define BRIDGE_GETHIGHERBYTE(x)		(uint8_t)((x & 0xff00) >> 8)
+#define BRIDGE_GETLOWERBYTE(x)		(uint8_t)((x & 0x00ff))
+
+/* fudge factor required to account for 8b/10b encoding */
+#define DP_CLK_FUDGE_NUM 10
+#define DP_CLK_FUDGE_DEN 8
+
+/* DPCD */
+#define DP_BRIDGE_DPCD_REV		0x700
+#define DP_BRIDGE_11			0x00
+#define DP_BRIDGE_12			0x01
+#define DP_BRIDGE_13			0x02
+#define DP_BRIDGE_14			0x03
+#define DP_BRIDGE_CONFIGURATION_SET	0x10a
+#define DP_MAX_LINK_RATE		0x001
+#define DP_MAX_LANE_COUNT		0x002
+#define DP_SUPPORTED_LINK_RATES		0x010 /* eDP 1.4 */
+#define DP_MAX_LINK_RATE		0x001
+#define DP_MAX_SUPPORTED_RATES		8 /* 16-bit little-endian */
+#define DP_LANE_COUNT_MASK		0xf
+
+/* link configuration */
+#define DP_LINK_BW_SET		0x100
+#define DP_LINK_BW_1_62		0x06
+#define DP_LINK_BW_2_7		0x0a
+#define DP_LINK_BW_5_4		0x14
+
+#define AUX_CMD_SEND		0x1
+#define MIN_DSI_CLK_FREQ_MHZ	40
+#define MAX_DSI_CLK_FREQ_MHZ    750
+
+enum bridge_regs {
+	SN_DPPLL_SRC_REG = 0x0A,
+	SN_PLL_ENABLE_REG = 0x0D,
+	SN_DSI_LANES_REG = 0x10,
+	SN_DSIA_CLK_FREQ_REG = 0x12,
+	SN_CHA_ACTIVE_LINE_LENGTH_LOW_REG = 0x20,
+	SN_CHA_ACTIVE_LINE_LENGTH_HIGH_REG = 0x21,
+	SN_CHA_VERTICAL_DISPLAY_SIZE_LOW_REG = 0x24,
+	SN_CHA_VERTICAL_DISPLAY_SIZE_HIGH_REG = 0x25,
+	SN_CHA_HSYNC_PULSE_WIDTH_LOW_REG = 0x2C,
+	SN_CHA_HSYNC_PULSE_WIDTH_HIGH_REG = 0x2D,
+	SN_CHA_VSYNC_PULSE_WIDTH_LOW_REG = 0x30,
+	SN_CHA_VSYNC_PULSE_WIDTH_HIGH_REG = 0x31,
+	SN_CHA_HORIZONTAL_BACK_PORCH_REG = 0x34,
+	SN_CHA_VERTICAL_BACK_PORCH_REG = 0x36,
+	SN_CHA_HORIZONTAL_FRONT_PORCH_REG = 0x38,
+	SN_CHA_VERTICAL_FRONT_PORCH_REG = 0x3A,
+	SN_COLOR_BAR_REG = 0x3C,
+	SN_ENH_FRAME_REG = 0x5A,
+	SN_DATA_FORMAT_REG = 0x5B,
+	SN_HPD_DISABLE_REG = 0x5C,
+	SN_I2C_CLAIM_ADDR_EN1 = 0x60,
+	SN_AUX_WDATA_REG_0 = 0x64,
+	SN_AUX_WDATA_REG_1 = 0x65,
+	SN_AUX_WDATA_REG_2 = 0x66,
+	SN_AUX_WDATA_REG_3 = 0x67,
+	SN_AUX_WDATA_REG_4 = 0x68,
+	SN_AUX_WDATA_REG_5 = 0x69,
+	SN_AUX_WDATA_REG_6 = 0x6A,
+	SN_AUX_WDATA_REG_7 = 0x6B,
+	SN_AUX_WDATA_REG_8 = 0x6C,
+	SN_AUX_WDATA_REG_9 = 0x6D,
+	SN_AUX_WDATA_REG_10 = 0x6E,
+	SN_AUX_WDATA_REG_11 = 0x6F,
+	SN_AUX_WDATA_REG_12 = 0x70,
+	SN_AUX_WDATA_REG_13 = 0x71,
+	SN_AUX_WDATA_REG_14 = 0x72,
+	SN_AUX_WDATA_REG_15 = 0x73,
+	SN_AUX_ADDR_19_16_REG = 0x74,
+	SN_AUX_ADDR_15_8_REG = 0x75,
+	SN_AUX_ADDR_7_0_REG = 0x76,
+	SN_AUX_LENGTH_REG = 0x77,
+	SN_AUX_CMD_REG = 0x78,
+	SN_AUX_RDATA_REG_0 = 0x79,
+	SN_AUX_RDATA_REG_1 = 0x7A,
+	SN_AUX_RDATA_REG_2 = 0x7B,
+	SN_AUX_RDATA_REG_3 = 0x7C,
+	SN_AUX_RDATA_REG_4 = 0x7D,
+	SN_AUX_RDATA_REG_5 = 0x7E,
+	SN_AUX_RDATA_REG_6 = 0x7F,
+	SN_AUX_RDATA_REG_7 = 0x80,
+	SN_AUX_RDATA_REG_8 = 0x81,
+	SN_AUX_RDATA_REG_9 = 0x82,
+	SN_AUX_RDATA_REG_10 = 0x83,
+	SN_AUX_RDATA_REG_11 = 0x84,
+	SN_AUX_RDATA_REG_12 = 0x85,
+	SN_AUX_RDATA_REG_13 = 0x86,
+	SN_AUX_RDATA_REG_14 = 0x87,
+	SN_AUX_RDATA_REG_15 = 0x88,
+	SN_SSC_CONFIG_REG = 0x93,
+	SN_DATARATE_CONFIG_REG = 0x94,
+	SN_ML_TX_MODE_REG = 0x96,
+	SN_AUX_CMD_STATUS_REG = 0xF4,
+};
+
+enum {
+	HPD_ENABLE = 0x0,
+	HPD_DISABLE = 0x1,
+};
+
+enum {
+	SOT_ERR_TOL_DSI = 0x0,
+	CHB_DSI_LANES = 0x1,
+	CHA_DSI_LANES = 0x2,
+	DSI_CHANNEL_MODE = 0x3,
+	LEFT_RIGHT_PIXELS = 0x4,
+};
+
+enum vstream_config {
+	VSTREAM_DISABLE = 0,
+	VSTREAM_ENABLE = 1,
+};
+
+enum i2c_over_aux {
+	I2C_OVER_AUX_WRITE_MOT_0 = 0x0,
+	I2C_OVER_AUX_READ_MOT_0 = 0x1,
+	I2C_OVER_AUX_WRITE_STATUS_UPDATE_0 = 0x4,
+	I2C_OVER_AUX_WRITE_MOT_1 = 0x5,
+	I2C_OVER_AUX_READ_MOT_1 = 0x6,
+	I2C_OVER_AUX_WRITE_STATUS_UPDATE_1 = 0x7,
+	NATIVE_AUX_WRITE = 0x8,
+	NATIVE_AUX_READ = 0x9,
+};
+
+enum ml_tx_mode {
+	MAIN_LINK_OFF = 0x0,
+	NORMAL_MODE = 0x1,
+	TPS1 = 0x2,
+	TPS2 = 0x3,
+	TPS3 = 0x4,
+	PRBS7 = 0x5,
+	HBR2_COMPLIANCE_EYE_PATTERN = 0x6,
+	SYMBOL_ERR_RATE_MEASUREMENT_PATTERN = 0x7,
+	CUTSOM_PATTERN = 0x8,
+	FAST_LINK_TRAINING = 0x9,
+	SEMI_AUTO_LINK_TRAINING = 0xa,
+	REDRIVER_SEMI_AUTO_LINK_TRAINING = 0xb,
+};
+
+enum dpcd_request {
+	DPCD_READ = 0x0,
+	DPCD_WRITE = 0x1,
+};
+
+enum {
+	EDID_LENGTH = 128,
+	EDID_I2C_ADDR = 0x50,
+	EDID_EXTENSION_FLAG = 0x7e,
+};
+
+/*
+ * LUT index corresponds to register value and LUT values corresponds
+ * to dp data rate supported by the bridge in Mbps unit.
+ */
+static const unsigned int sn65dsi86_bridge_dp_rate_lut[] = {
+	0, 1620, 2160, 2430, 2700, 3240, 4320, 5400
+};
+
+enum cb_err sn65dsi86_bridge_read_edid(uint8_t bus, uint8_t chip, struct edid *out)
+{
+	int ret;
+	u8 edid[EDID_LENGTH * 2];
+	int edid_size = EDID_LENGTH;
+
+	/* Send I2C command to claim EDID I2c slave */
+	i2c_writeb(bus, chip, SN_I2C_CLAIM_ADDR_EN1, (EDID_I2C_ADDR << 1) | 0x1);
+
+	/* read EDID */
+	ret = i2c_read_bytes(bus, EDID_I2C_ADDR, 0x0, edid, EDID_LENGTH);
+	if (ret != 0) {
+		printk(BIOS_ERR, "ERROR: Failed to read EDID.\n");
+		return CB_ERR;
+	}
+
+	if (edid[EDID_EXTENSION_FLAG]) {
+		edid_size += EDID_LENGTH;
+		ret = i2c_read_bytes(bus, EDID_I2C_ADDR, EDID_LENGTH,
+					&edid[EDID_LENGTH], EDID_LENGTH);
+		if (ret != 0) {
+			printk(BIOS_ERR, "Failed to read EDID ext block.\n");
+			return CB_ERR;
+		}
+	}
+
+	if (decode_edid(edid, edid_size, out) != EDID_CONFORMANT) {
+		printk(BIOS_ERR, "ERROR: Failed to decode EDID.\n");
+		return CB_ERR;
+	}
+
+	return CB_SUCCESS;
+}
+
+static void sn65dsi86_bridge_dpcd_request(uint8_t bus,
+					  uint8_t chip,
+					  unsigned int dpcd_reg,
+					  unsigned int len,
+					  enum dpcd_request request,
+					  uint8_t *data)
+{
+	int i;
+	uint32_t length;
+	uint8_t buf;
+	uint8_t reg;
+
+	while (len) {
+		length = MIN(len, 16);
+
+		i2c_writeb(bus, chip, SN_AUX_ADDR_19_16_REG, (dpcd_reg >> 16) & 0xF);
+		i2c_writeb(bus, chip, SN_AUX_ADDR_15_8_REG, (dpcd_reg >> 8) & 0xFF);
+		i2c_writeb(bus, chip, SN_AUX_ADDR_7_0_REG, (dpcd_reg) & 0xFF);
+		i2c_writeb(bus, chip, SN_AUX_LENGTH_REG, length); /* size of 1 Byte data */
+		if (request == DPCD_WRITE) {
+			reg = SN_AUX_WDATA_REG_0;
+			for (i = 0; i < length; i++)
+				i2c_writeb(bus, chip, reg++, *data++);
+
+			i2c_writeb(bus, chip,
+				   SN_AUX_CMD_REG, AUX_CMD_SEND | (NATIVE_AUX_WRITE << 4));
+		} else {
+			i2c_writeb(bus, chip,
+				   SN_AUX_CMD_REG, AUX_CMD_SEND | (NATIVE_AUX_READ << 4));
+			if (!wait_ms(100,
+			    !i2c_readb(bus, chip, SN_AUX_CMD_REG,
+			    &buf) && !(buf & AUX_CMD_SEND))) {
+				printk(BIOS_ERR, "ERROR: aux command send failed\n");
+			}
+
+			reg = SN_AUX_RDATA_REG_0;
+			for (i = 0; i < length; i++) {
+				i2c_readb(bus, chip, reg++, &buf);
+				*data++ = buf;
+			}
+		}
+
+		len -= length;
+	}
+}
+
+static void sn65dsi86_bridge_valid_dp_rates(uint8_t bus, uint8_t chip, bool rate_valid[])
+{
+	unsigned int rate_per_200khz;
+	uint8_t dpcd_val;
+	int i, j;
+
+	sn65dsi86_bridge_dpcd_request(bus, chip,
+					DP_BRIDGE_DPCD_REV, 1, DPCD_READ, &dpcd_val);
+	if (dpcd_val >= DP_BRIDGE_14) {
+		/* eDP 1.4 devices must provide a custom table */
+		uint8_t sink_rates[DP_MAX_SUPPORTED_RATES * 2];
+
+		sn65dsi86_bridge_dpcd_request(bus, chip, DP_SUPPORTED_LINK_RATES,
+					      sizeof(sink_rates),
+					      DPCD_READ, sink_rates);
+		for (i = 0; i < ARRAY_SIZE(sink_rates); i++) {
+			rate_per_200khz = le16_to_cpu(sink_rates[i]);
+
+			if (!rate_per_200khz)
+				break;
+
+			for (j = 0;
+			     j < ARRAY_SIZE(sn65dsi86_bridge_dp_rate_lut);
+			     j++) {
+				if (sn65dsi86_bridge_dp_rate_lut[j] * (MHz / KHz) ==
+				    rate_per_200khz * 200)
+					rate_valid[j] = true;
+			}
+		}
+
+		for (i = 0; i < ARRAY_SIZE(sn65dsi86_bridge_dp_rate_lut); i++) {
+			if (rate_valid[i])
+				return;
+		}
+
+		printk(BIOS_ERR, "No matching eDP rates in table; falling back\n");
+	}
+
+	/* On older versions best we can do is use DP_MAX_LINK_RATE */
+	 sn65dsi86_bridge_dpcd_request(bus, chip,
+					DP_MAX_LINK_RATE, 1, DPCD_READ, &dpcd_val);
+
+	switch (dpcd_val) {
+	default:
+		printk(BIOS_ERR,
+			      "Unexpected max rate (%#x); assuming 5.4 GHz\n",
+			      (int)dpcd_val);
+		/* fall through */
+	case DP_LINK_BW_5_4:
+		rate_valid[7] = 1;
+		/* fall through */
+	case DP_LINK_BW_2_7:
+		rate_valid[4] = 1;
+		/* fall through */
+	case DP_LINK_BW_1_62:
+		rate_valid[1] = 1;
+		break;
+	}
+}
+
+static void sn65dsi86_bridge_set_dsi_clock_range(uint8_t bus, uint8_t chip,
+						 struct edid *edid,
+						 uint32_t num_of_lanes, uint32_t bpp)
+{
+	uint64_t pixel_clk_hz;
+	uint64_t stream_bit_rate_mhz;
+	uint64_t min_req_dsi_clk;
+
+	pixel_clk_hz = edid->mode.pixel_clock * KHz;
+	stream_bit_rate_mhz = (pixel_clk_hz * bpp) / MHz;
+
+	/* For TI the clock frequencies are half the bit rates */
+	min_req_dsi_clk = stream_bit_rate_mhz / (num_of_lanes * 2);
+
+	/* for each increment in val, frequency increases by 5MHz */
+	min_req_dsi_clk = MAX(MIN_DSI_CLK_FREQ_MHZ,
+			  MIN(MAX_DSI_CLK_FREQ_MHZ, min_req_dsi_clk)) / 5;
+	i2c_writeb(bus, chip, SN_DSIA_CLK_FREQ_REG, min_req_dsi_clk);
+}
+
+static void sn65dsi86_bridge_set_dp_clock_range(uint8_t bus, uint8_t chip,
+						struct edid *edid, uint32_t num_of_lanes)
+{
+	uint64_t stream_bit_rate_khz;
+	bool rate_valid[ARRAY_SIZE(sn65dsi86_bridge_dp_rate_lut)] = { };
+	uint64_t dp_rate_mhz;
+	int dp_rate_idx, i;
+
+	stream_bit_rate_khz = edid->mode.pixel_clock * 18;
+
+	/* Calculate minimum DP data rate, taking 80% as per DP spec */
+	dp_rate_mhz = DIV_ROUND_UP(stream_bit_rate_khz * DP_CLK_FUDGE_NUM,
+				   KHz * num_of_lanes * DP_CLK_FUDGE_DEN);
+
+	for (i = 0; i < ARRAY_SIZE(sn65dsi86_bridge_dp_rate_lut) - 1; i++)
+		if (sn65dsi86_bridge_dp_rate_lut[i] > dp_rate_mhz)
+			break;
+
+	sn65dsi86_bridge_valid_dp_rates(bus, chip, rate_valid);
+
+	/* Train until we run out of rates */
+	for (dp_rate_idx = i;
+	     dp_rate_idx < ARRAY_SIZE(sn65dsi86_bridge_dp_rate_lut);
+	     dp_rate_idx++)
+		if (rate_valid[dp_rate_idx])
+			break;
+
+	if (dp_rate_idx < ARRAY_SIZE(sn65dsi86_bridge_dp_rate_lut))
+		i2c_write_field(bus, chip, SN_DATARATE_CONFIG_REG, dp_rate_idx, 8, 5);
+	else
+		printk(BIOS_ERR, "ERROR: valid dp rate not found");
+}
+
+static void sn65dsi86_bridge_set_bridge_active_timing(uint8_t bus,
+						      uint8_t chip,
+						      struct edid *edid)
+{
+	i2c_writeb(bus, chip, SN_CHA_ACTIVE_LINE_LENGTH_LOW_REG,
+			   BRIDGE_GETLOWERBYTE(edid->mode.ha));
+	i2c_writeb(bus, chip, SN_CHA_ACTIVE_LINE_LENGTH_HIGH_REG,
+			   BRIDGE_GETHIGHERBYTE(edid->mode.ha));
+	i2c_writeb(bus, chip, SN_CHA_VERTICAL_DISPLAY_SIZE_LOW_REG,
+			   BRIDGE_GETLOWERBYTE(edid->mode.va));
+	i2c_writeb(bus, chip, SN_CHA_VERTICAL_DISPLAY_SIZE_HIGH_REG,
+			   BRIDGE_GETHIGHERBYTE(edid->mode.va));
+	i2c_writeb(bus, chip, SN_CHA_HSYNC_PULSE_WIDTH_LOW_REG,
+			   BRIDGE_GETLOWERBYTE(edid->mode.hspw));
+	i2c_writeb(bus, chip, SN_CHA_HSYNC_PULSE_WIDTH_HIGH_REG,
+			   BRIDGE_GETHIGHERBYTE(edid->mode.hspw));
+	i2c_writeb(bus, chip, SN_CHA_VSYNC_PULSE_WIDTH_LOW_REG,
+			   BRIDGE_GETLOWERBYTE(edid->mode.vspw));
+	i2c_writeb(bus, chip, SN_CHA_VSYNC_PULSE_WIDTH_HIGH_REG,
+			   BRIDGE_GETHIGHERBYTE(edid->mode.vspw));
+	i2c_writeb(bus, chip, SN_CHA_HORIZONTAL_BACK_PORCH_REG,
+			   edid->mode.hbl - edid->mode.hso - edid->mode.hspw);
+	i2c_writeb(bus, chip, SN_CHA_VERTICAL_BACK_PORCH_REG,
+			   edid->mode.vbl - edid->mode.vso - edid->mode.vspw);
+	i2c_writeb(bus, chip, SN_CHA_HORIZONTAL_FRONT_PORCH_REG,
+			   edid->mode.hso);
+	i2c_writeb(bus, chip, SN_CHA_VERTICAL_FRONT_PORCH_REG,
+			   edid->mode.vso);
+}
+
+static void sn65dsi86_bridge_link_training(uint8_t bus, uint8_t chip)
+{
+	uint8_t buf;
+
+	/* enable pll lock */
+	i2c_writeb(bus, chip, SN_PLL_ENABLE_REG, 0x1);
+
+	if (!wait_ms(500,
+	    !(i2c_readb(bus, chip, SN_DPPLL_SRC_REG, &buf)) &&
+	    (buf & BIT(7)))) {
+		printk(BIOS_ERR, "ERROR: PLL lock failure\n");
+	}
+
+	/*
+	 * The SN65DSI86 only supports ASSR Display Authentication method and
+	 * this method is enabled by default. An eDP panel must support this
+	 * authentication method. We need to enable this method in the eDP panel
+	 * at DisplayPort address 0x0010A prior to link training.
+	 */
+	buf = 0x1;
+	sn65dsi86_bridge_dpcd_request(bus, chip,
+				      DP_BRIDGE_CONFIGURATION_SET, 1, DPCD_WRITE, &buf);
+
+	/* semi auto link training mode */
+	i2c_writeb(bus, chip, SN_ML_TX_MODE_REG, 0xa);
+
+	if (!wait_ms(500,
+	    !(i2c_readb(bus, chip, SN_ML_TX_MODE_REG, &buf)) &&
+	    (buf & NORMAL_MODE))) {
+		printk(BIOS_ERR, "ERROR: Link training failed");
+	}
+
+}
+
+static enum cb_err sn65dsi86_bridge_get_plug_in_status(uint8_t bus, uint8_t chip)
+{
+	int val;
+	uint8_t buf;
+
+	val = i2c_readb(bus, chip, SN_HPD_DISABLE_REG, &buf);
+	if (val == 0 && (buf & HPD_DISABLE))
+		return CB_SUCCESS;
+
+	return CB_ERR;
+}
+
+/*
+ * support bridge HPD function some hardware versions do not support bridge hdp,
+ * we use 360ms to try to get the hpd single now, if we can not get bridge hpd single,
+ * it will delay 360ms, also meet the bridge power timing request, to be compatible
+ * all of the hardware versions
+ */
+static void sn65dsi86_bridge_wait_hpd(uint8_t bus, uint8_t chip)
+{
+	if (wait_ms(400, sn65dsi86_bridge_get_plug_in_status(bus, chip)))
+		return;
+
+	printk(BIOS_WARNING, "HPD detection failed, force hpd\n");
+
+	/* Force HPD */
+	i2c_write_field(bus, chip, SN_HPD_DISABLE_REG, HPD_DISABLE, 1, 0);
+}
+
+static void sn65dsi86_bridge_assr_config(uint8_t bus, uint8_t chip, int enable)
+{
+	if (enable)
+		i2c_write_field(bus, chip, SN_ENH_FRAME_REG, VSTREAM_ENABLE, 1, 3);
+	else
+		i2c_write_field(bus, chip, SN_ENH_FRAME_REG, VSTREAM_DISABLE, 1, 3);
+}
+
+static int sn65dsi86_bridge_dp_lane_config(uint8_t bus, uint8_t chip)
+{
+	uint8_t lane_count;
+
+	sn65dsi86_bridge_dpcd_request(bus, chip, DP_MAX_LANE_COUNT, 1, DPCD_READ, &lane_count);
+	lane_count &= DP_LANE_COUNT_MASK;
+	i2c_write_field(bus, chip, SN_SSC_CONFIG_REG, MIN(lane_count, 3), 3, 4);
+
+	return lane_count;
+}
+
+void sn65dsi86_bridge_init(uint8_t bus, uint8_t chip, enum dp_pll_clk_src ref_clk)
+{
+	sn65dsi86_bridge_wait_hpd(bus, chip);
+
+	/* set refclk to 19.2 MHZ */
+	i2c_write_field(bus, chip, SN_DPPLL_SRC_REG, ref_clk, 7, 1);
+}
+
+void sn65dsi86_bridge_configure(uint8_t bus, uint8_t chip,
+				struct edid *edid, uint32_t num_of_lanes,
+				uint32_t dsi_bpp)
+{
+	int dp_lanes;
+
+	/* DSI Lanes config */
+	i2c_write_field(bus, chip, SN_DSI_LANES_REG, (4 - num_of_lanes), 3, 3);
+
+	/* DP Lane config */
+	dp_lanes = sn65dsi86_bridge_dp_lane_config(bus, chip);
+
+	sn65dsi86_bridge_set_dsi_clock_range(bus, chip, edid, num_of_lanes, dsi_bpp);
+
+	sn65dsi86_bridge_set_dp_clock_range(bus, chip, edid, dp_lanes);
+
+	/* Disable vstream */
+	sn65dsi86_bridge_assr_config(bus, chip, 0);
+	sn65dsi86_bridge_link_training(bus, chip);
+	sn65dsi86_bridge_set_bridge_active_timing(bus, chip, edid);
+
+	/* DP BPP config */
+	i2c_writeb(bus, chip, SN_DATA_FORMAT_REG, 0x1);
+
+	/* color bar disabled */
+	i2c_writeb(bus, chip, SN_COLOR_BAR_REG, 0x5);
+
+	/* Enable vstream */
+	sn65dsi86_bridge_assr_config(bus, chip, 1);
+}
diff --git a/src/drivers/ti/sn65dsi86bridge/sn65dsi86bridge.h b/src/drivers/ti/sn65dsi86bridge/sn65dsi86bridge.h
new file mode 100644
index 0000000000..83b940bbb4
--- /dev/null
+++ b/src/drivers/ti/sn65dsi86bridge/sn65dsi86bridge.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef __TI_SN65DSI86BRIDGE_H
+#define __TI_SN65DSI86BRIDGE_H
+
+#include <edid.h>
+
+enum dp_pll_clk_src {
+	SN65_SEL_12MHZ = 0x0,
+	SN65_SEL_19MHZ = 0x1,
+	SN65_SEL_26MHZ = 0x2,
+	SN65_SEL_27MHZ = 0x3,
+	SN65_SEL_38MHZ = 0x4,
+};
+
+void sn65dsi86_bridge_init(uint8_t bus, uint8_t chip, enum dp_pll_clk_src ref_clk);
+void sn65dsi86_bridge_configure(uint8_t bus, uint8_t chip,
+				struct edid *edid, uint32_t num_of_lines,
+				uint32_t dsi_bpp);
+enum cb_err sn65dsi86_bridge_read_edid(uint8_t bus, uint8_t chip, struct edid *out);
+
+#endif