Intel E7501 P64H2 ICH5R support

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1616 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
author: Yinghai Lu <yinghailu@gmail.com> 2004-07-01 03:55:03 +0000
committer: Yinghai Lu <yinghailu@gmail.com> 2004-07-01 03:55:03 +0000
commit: 70093f7875371abe52c4417c6cc3a427d20781c5 (patch)
tree: f5812172eab817e66840583c669f16d4b1121531
parent: 7dea9552d5fa10c5542e744fe1d8e0a81689e3c1 (diff)
47 files changed, 5035 insertions, 11 deletions
diff --git a/src/cpu/p6/Config.lb b/src/cpu/p6/Config.lb
index d4918f9147..8242a6e874 100644
--- a/src/cpu/p6/Config.lb
+++ b/src/cpu/p6/Config.lb
@@ -1,5 +1,10 @@
 uses INTEL_PPRO_MTRR
+uses CPU_FIXUP
 dir /cpu/p5
-object cpufixup.o
+config chip.h
+if CPU_FIXUP
+  object cpufixup.o
+  object apic_timer.o
+end
 object mtrr.o
 object pgtbl.o
diff --git a/src/cpu/p6/apic_timer.c b/src/cpu/p6/apic_timer.c
new file mode 100644
index 0000000000..fa7e9b905f
--- /dev/null
+++ b/src/cpu/p6/apic_timer.c
@@ -0,0 +1,26 @@
+#include <stdint.h>
+#include <delay.h>
+#include <cpu/p6/msr.h>
+#include <cpu/p6/apic.h>
+
+void init_timer(void)
+{
+	/* Set the apic timer to no interrupts and periodic mode */
+	apic_write(APIC_LVTT, (1 << 17)|(1<< 16)|(0 << 12)|(0 << 0));
+	/* Set the divider to 1, no divider */
+	apic_write(APIC_TDCR, APIC_TDR_DIV_1);
+	/* Set the initial counter to 0xffffffff */
+	apic_write(APIC_TMICT, 0xffffffff);
+}
+
+void udelay(unsigned usecs)
+{
+	uint32_t start, value, ticks;
+	/* Calculate the number of ticks to run, our FSB runs a 200Mhz */
+	ticks = usecs * 200;
+	start = apic_read(APIC_TMCCT);
+	do {
+		value = apic_read(APIC_TMCCT);
+	} while((start - value) < ticks);
+	
+}
diff --git a/src/cpu/p6/chip.h b/src/cpu/p6/chip.h
new file mode 100644
index 0000000000..bfcdf79ed7
--- /dev/null
+++ b/src/cpu/p6/chip.h
@@ -0,0 +1,5 @@
+extern struct chip_control cpu_p6_control;
+
+struct cpu_p6_config {
+	int nothing;
+};
diff --git a/src/cpu/p6/cpufixup.c b/src/cpu/p6/cpufixup.c
index e5cd3fc017..f611524fab 100644
--- a/src/cpu/p6/cpufixup.c
+++ b/src/cpu/p6/cpufixup.c
@@ -351,3 +351,27 @@ void p6_cpufixup(struct mem_range *mem)
 	printk_debug("Updating microcode\n");
 	display_cpuid_update_microcode();
 }
+
+
+static
+void p6_enable(struct chip *chip, enum chip_pass pass)
+{
+
+        struct cpu_p6_config *conf = (struct cpu_p6_config *)chip->chip_info;
+
+        switch (pass) {
+        case CONF_PASS_PRE_CONSOLE:
+                break;
+        case CONF_PASS_PRE_PCI:
+                init_timer();
+                break;
+        default:
+                /* nothing yet */
+                break;
+        }
+}
+
+struct chip_control cpu_p6_control = {
+        .enable = p6_enable,
+        .name   = "Intel P6  CPU",
+};
diff --git a/src/cpu/p6/disable_mmx_sse.inc b/src/cpu/p6/disable_mmx_sse.inc
new file mode 100644
index 0000000000..5ce9dfdc1f
--- /dev/null
+++ b/src/cpu/p6/disable_mmx_sse.inc
@@ -0,0 +1,27 @@
+	/* Clear out an mmx state */
+	emms
+
+	/*
+	 * Put the processor back into a reset state
+	 * with respect to the xmm registers.
+	 */
+	
+	pxor %xmm0, %xmm0
+	pxor %xmm1, %xmm1
+	pxor %xmm2, %xmm2
+	pxor %xmm3, %xmm3
+	pxor %xmm4, %xmm4
+	pxor %xmm5, %xmm5
+	pxor %xmm6, %xmm6
+	pxor %xmm7, %xmm7
+
+	/* Disable floating point emulation */
+	movl	%cr0, %eax
+	andl	$~(1<<2), %eax
+	movl	%eax, %cr0
+
+	/* Disable sse instructions */
+	movl	%cr4, %eax
+	andl	$~(3<<9), %eax
+	movl	%eax, %cr4
+
diff --git a/src/cpu/p6/enable_mmx_sse.inc b/src/cpu/p6/enable_mmx_sse.inc
new file mode 100644
index 0000000000..f0b2487b8c
--- /dev/null
+++ b/src/cpu/p6/enable_mmx_sse.inc
@@ -0,0 +1,25 @@
+	/* Save the BIST result */
+	movl	%eax, %ebp
+	
+	/*
+	 * Enabling mmx registers is a noop
+	 * Enable the use of the xmm registers
+	 */
+
+        /* Enable sse instructions */
+        movl    %cr4, %eax
+        orl     $(1<<9), %eax
+        movl    %eax, %cr4
+
+	/* Disable floating point emulation */
+	movl	%cr0, %eax
+	andl	$~(1<<2), %eax
+	movl	%eax, %cr0
+
+        /* enable sse extension */
+        movl    %cr0, %eax
+        andl    $~(1<<1), %eax
+        movl    %eax, %cr0
+
+	/* Restore the BIST result */
+	movl	%ebp, %eax
diff --git a/src/include/device/pci_ids.h b/src/include/device/pci_ids.h
index 586083a966..eeab66cc16 100644
--- a/src/include/device/pci_ids.h
+++ b/src/include/device/pci_ids.h
@@ -1890,6 +1890,20 @@
 #define PCI_DEVICE_ID_INTEL_82801CA_1F5 0x2485 
 #define PCI_DEVICE_ID_INTEL_82801CA_1D2 0x2487
 
+#define PCI_DEVICE_ID_INTEL_82801ER_1E0 0x244e 
+#define PCI_DEVICE_ID_INTEL_82801ER_1F0 0x24d0 
+#define PCI_DEVICE_ID_INTEL_82801ER_1F1 0x24db 
+#define PCI_DEVICE_ID_INTEL_82801ER_1F2 0x24d1
+#define PCI_DEVICE_ID_INTEL_82801ER_1F2_R 0x24df 
+#define PCI_DEVICE_ID_INTEL_82801ER_1F3 0x24d3 
+#define PCI_DEVICE_ID_INTEL_82801ER_1F5 0x24d5 
+#define PCI_DEVICE_ID_INTEL_82801ER_1F6 0x24d6
+#define PCI_DEVICE_ID_INTEL_82801ER_1D0 0x24d2 
+#define PCI_DEVICE_ID_INTEL_82801ER_1D1 0x24d4 
+#define PCI_DEVICE_ID_INTEL_82801ER_1D2 0x24d7
+#define PCI_DEVICE_ID_INTEL_82801ER_1D3 0x24de
+#define PCI_DEVICE_ID_INTEL_82801ER_1D7 0x24dd
+
 #define PCI_DEVICE_ID_INTEL_82870_1E0   0x1461 
 #define PCI_DEVICE_ID_INTEL_82870_1F0   0x1460 
 
diff --git a/src/mainboard/tyan/s2735/Config.lb b/src/mainboard/tyan/s2735/Config.lb
new file mode 100644
index 0000000000..2b94689ba6
--- /dev/null
+++ b/src/mainboard/tyan/s2735/Config.lb
@@ -0,0 +1,222 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD
+uses ARCH
+uses HARD_RESET_BUS
+uses HARD_RESET_DEVICE
+uses HARD_RESET_FUNCTION
+#
+#
+###
+### Set all of the defaults for an x86 architecture
+###
+#
+#
+###
+### Build the objects we have code for in this directory.
+###
+##object mainboard.o
+config chip.h
+register "fixup_scsi" = "1" 
+register "fixup_vga" = "1"
+
+
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+driver mainboard.o
+#dir /drvers/adaptec/7902
+#dir /drivers/si/3114
+#dir /drivers/intel/82551_ipmi
+#dir /drivers/ati/ragexl
+if HAVE_MP_TABLE object mptable.o end
+if HAVE_PIRQ_TABLE object irq_tables.o end
+#
+#default HARD_RESET_BUS=1
+#default HARD_RESET_DEVICE=4
+#default HARD_RESET_FUNCTION=0
+#
+arch i386 end
+#
+###
+### Build our 16 bit and 32 bit linuxBIOS entry code
+###
+mainboardinit cpu/i386/entry16.inc
+mainboardinit cpu/i386/entry32.inc
+mainboardinit cpu/i386/bist32.inc
+ldscript /cpu/i386/entry16.lds
+ldscript /cpu/i386/entry32.lds
+#
+###
+### Build our reset vector (This is where linuxBIOS is entered)
+###
+if USE_FALLBACK_IMAGE 
+	mainboardinit cpu/i386/reset16.inc 
+	ldscript /cpu/i386/reset16.lds 
+else
+	mainboardinit cpu/i386/reset32.inc 
+	ldscript /cpu/i386/reset32.lds 
+end
+#
+#### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+#
+###
+### Include an id string (For safe flashing)
+###
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+#
+####
+#### This is the early phase of linuxBIOS startup 
+#### Things are delicate and we test to see if we should
+#### failover to another image.
+####
+#option MAX_REBOOT_CNT=2
+if USE_FALLBACK_IMAGE
+  ldscript /arch/i386/lib/failover.lds 
+end
+#
+###
+### Setup our mtrrs
+###
+#mainboardinit cpu/p6/earlymtrr.inc
+###
+### Only the bootstrap cpu makes it here.
+### Failover if we need to 
+###
+#
+if USE_FALLBACK_IMAGE
+  mainboardinit ./failover.inc
+end
+
+#
+#
+###
+### Setup the serial port
+###
+mainboardinit pc80/serial.inc
+mainboardinit arch/i386/lib/console.inc
+mainboardinit cpu/i386/bist32_fail.inc
+#
+####
+#### O.k. We aren't just an intermediary anymore!
+####
+#
+###
+### When debugging disable the watchdog timer
+###
+##option MAXIMUM_CONSOLE_LOGLEVEL=7
+#default MAXIMUM_CONSOLE_LOGLEVEL=7
+#
+#if USE_FALLBACK_IMAGE mainboardinit arch/i386/lib/noop_failover.inc  end
+#
+###
+### Romcc output
+###
+
+makerule ./failover.E
+	depends "$(MAINBOARD)/failover.c" 
+	action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E"
+end
+
+makerule ./failover.inc
+	depends "./romcc ./failover.E"
+	action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
+end
+
+makerule ./auto.E 
+        depends "$(MAINBOARD)/auto.c option_table.h"
+        action  "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+end
+makerule ./auto.inc 
+	depends "./romcc ./auto.E"
+	action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E" 
+#        action  "./romcc -O2 ./auto.E > auto.inc"
+end
+mainboardinit cpu/p6/enable_mmx_sse.inc
+mainboardinit ./auto.inc
+mainboardinit cpu/p6/disable_mmx_sse.inc
+#
+###
+### Include the secondary Configuration files 
+###
+
+config chip.h
+
+northbridge intel/e7501 "e7501"
+		pci 0:2.0
+		pci 0:0.0
+		pci 0:0.1
+                pci 0:6.0
+	southbridge intel/i82870 "i82870"
+		pci 0:1c.0
+		pci 0:1d.0
+		pci 0:1e.0
+		pci 0:1f.0
+	end
+end
+        southbridge intel/i82801er "i82801er"
+                pci 0:1f.0 
+                pci 0:1d.0 on
+                pci 0:1d.1 on
+                pci 0:1d.2 on
+                pci 0:1d.3 on
+                pci 0:1d.7 on
+                pci 0:1e.0 on
+                pci 0:1f.1 off
+                pci 0:1f.2 on
+                pci 0:1f.3 on
+                pci 0:1f.5 off
+                pci 0:1f.6 off
+#                pci 1:8.0 off
+                superio winbond/w83627hf 
+                        pnp 2e.0 on #  Floppy
+                                 io 0x60 = 0x3f0
+                                irq 0x70 = 6
+                                drq 0x74 = 2
+                        pnp 2e.1 off #  Parallel Port
+                                 io 0x60 = 0x378
+                                irq 0x70 = 7
+                        pnp 2e.2 on #  Com1
+                                 io 0x60 = 0x3f8
+                                irq 0x70 = 4
+                        pnp 2e.3 off #  Com2
+                                 io 0x60 = 0x2f8
+                                irq 0x70 = 3
+                        pnp 2e.5 on #  Keyboard
+                                 io 0x60 = 0x60
+                                 io 0x62 = 0x64
+                                irq 0x70 = 1
+				irq 0x72 = 12
+                        pnp 2e.6 off #  CIR
+                        pnp 2e.7 off #  GAME_MIDI_GIPO1
+                        pnp 2e.8 off #  GPIO2
+                        pnp 2e.9 off #  GPIO3
+                        pnp 2e.a off #  ACPI
+                        pnp 2e.b on  #  HW Monitor
+				 io 0x60 = 0x290
+                end
+        end
+#end
+dir /pc80
+#dir /bioscall
+cpu p6 "cpu0"
+end
+
+cpu p6 "cpu1"
+end
+
+cpu p6 "cpu2"
+end
+
+cpu p6 "cpu3"
+end
diff --git a/src/mainboard/tyan/s2735/auto.c b/src/mainboard/tyan/s2735/auto.c
new file mode 100644
index 0000000000..3a99aa29a9
--- /dev/null
+++ b/src/mainboard/tyan/s2735/auto.c
@@ -0,0 +1,135 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/smp/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "southbridge/intel/i82801er/i82801er_early_smbus.c"
+#include "northbridge/intel/e7501/raminit.h"
+
+#if 1
+#include "cpu/p6/apic_timer.c"
+#include "lib/delay.c"
+#endif
+
+#include "cpu/p6/boot_cpu.c"
+#include "northbridge/intel/e7501/debug.c"
+#include "superio/winbond/w83627hf/w83627hf_early_serial.c" 
+
+#include "cpu/p6/earlymtrr.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
+
+static void hard_reset(void)
+{
+        outb(0x0e, 0x0cf9);
+}
+
+static void memreset_setup(void)
+{
+}
+
+static void memreset(int controllers, const struct mem_controller *ctrl)
+{
+}
+
+
+
+static inline void activate_spd_rom(const struct mem_controller *ctrl)
+{
+        /* nothing to do */
+}
+ 
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+	return smbus_read_byte(device, address);
+}
+
+#include "northbridge/intel/e7501/raminit.c"
+#include "northbridge/intel/e7501/reset_test.c"
+#include "sdram/generic_sdram.c"
+
+static void main(void)
+{
+	static const struct mem_controller memctrl[] = {
+		{
+			.d0 = PCI_DEV(0, 0, 0),
+			.d0f1 = PCI_DEV(0, 0, 1),
+			.channel0 = { (0xa<<3)|0, (0xa<<3)|1, (0xa<<3)|2, 0 },
+			.channel1 = { (0xa<<3)|4, (0xa<<3)|5, (0xa<<3)|6, 0 },
+		},
+	};
+
+#if 1
+        enable_lapic();
+        init_timer();
+#endif
+        
+        w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+        uart_init();
+        console_init();
+//        setup_default_resource_map();
+#if 0
+	print_pci_devices();
+#endif
+	if(!bios_reset_detected()) {
+        	enable_smbus();
+#if 0
+//      	dump_spd_registers(&memctrl[0]);
+        	dump_smbus_registers();
+#endif
+
+		memreset_setup();
+		sdram_initialize(sizeof(memctrl)/sizeof(memctrl[0]), memctrl);
+	} 
+#if 0
+	else {
+		        /* clear memory 1meg */
+        __asm__ volatile(
+                "1: \n\t"
+                "movl %0, %%fs:(%1)\n\t"
+                "addl $4,%1\n\t"
+                "subl $4,%2\n\t"
+                "jnz 1b\n\t"
+                :
+                : "a" (0), "D" (0), "c" (1024*1024)
+                ); 
+	
+	}
+#endif
+
+#if 0
+	dump_pci_devices();
+#endif
+#if 0
+	dump_pci_device(PCI_DEV(0, 0, 0));
+#endif
+
+#if 0
+	msr_t msr;
+	msr = rdmsr(TOP_MEM2);
+	print_debug("TOP_MEM2: ");
+	print_debug_hex32(msr.hi);
+	print_debug_hex32(msr.lo);
+	print_debug("\r\n");
+#endif
+/*
+#if  0
+	ram_check(0x00000000, msr.lo+(msr.hi<<32));
+#else
+#if 0
+	// Check 16MB of memory @ 0
+	ram_check(0x00000000, 0x01000000);
+#else
+	// Check 16MB of memory @ 2GB 
+	ram_check(0x80000000, 0x81000000);
+#endif
+#endif
+*/
+}
diff --git a/src/mainboard/tyan/s2735/chip.h b/src/mainboard/tyan/s2735/chip.h
new file mode 100644
index 0000000000..f3a2ec6962
--- /dev/null
+++ b/src/mainboard/tyan/s2735/chip.h
@@ -0,0 +1,6 @@
+extern struct chip_control mainboard_tyan_s2735_control;
+
+struct mainboard_tyan_s2735_config {
+	int fixup_scsi;
+	int fixup_vga;
+};
diff --git a/src/mainboard/tyan/s2735/cmos.layout b/src/mainboard/tyan/s2735/cmos.layout
new file mode 100644
index 0000000000..2252e6720c
--- /dev/null
+++ b/src/mainboard/tyan/s2735/cmos.layout
@@ -0,0 +1,96 @@
+entries
+
+#start-bit length  config config-ID    name
+#0            8       r       0        seconds
+#8            8       r       0        alarm_seconds
+#16           8       r       0        minutes
+#24           8       r       0        alarm_minutes
+#32           8       r       0        hours
+#40           8       r       0        alarm_hours
+#48           8       r       0        day_of_week
+#56           8       r       0        day_of_month
+#64           8       r       0        month
+#72           8       r       0        year
+#80           4       r       0        rate_select
+#84           3       r       0        REF_Clock
+#87           1       r       0        UIP
+#88           1       r       0        auto_switch_DST
+#89           1       r       0        24_hour_mode
+#90           1       r       0        binary_values_enable
+#91           1       r       0        square-wave_out_enable
+#92           1       r       0        update_finished_enable
+#93           1       r       0        alarm_interrupt_enable
+#94           1       r       0        periodic_interrupt_enable
+#95           1       r       0        disable_clock_updates
+#96         288       r       0        temporary_filler
+0          384       r       0        reserved_memory
+384          1       e       4        boot_option
+385          1       e       4        last_boot
+386          1       e       1        ECC_memory
+388          4       r       0        reboot_bits
+392          3       e       5        baud_rate
+395          1       e       2        hyper_threading
+396          1       e       1        thermal_monitoring 
+397          1       e       1        remap_memory_high 
+400          1       e       1        power_on_after_fail
+412          4       e       6        debug_level
+416          4       e       7        boot_first
+420          4       e       7        boot_second
+424          4       e       7        boot_third
+428          4       h       0        boot_index
+432	     8       h       0        boot_countdown
+#440          4       e       9        slow_cpu
+444          1       e       1        nmi
+728        256       h       0        user_data
+984         16       h       0        check_sum
+# Reserve the extended AMD configuration registers
+1000        24       r       0        reserved_memory
+
+
+
+enumerations
+
+#ID value   text
+1     0     Disable
+1     1     Enable
+2     0     Enable
+2     1     Disable
+4     0     Fallback
+4     1     Normal
+5     0     115200
+5     1     57600
+5     2     38400
+5     3     19200
+5     4     9600
+5     5     4800
+5     6     2400
+5     7     1200
+6     6     Notice
+6     7     Info
+6     8     Debug
+6     9     Spew
+7     0     Network
+7     1     HDD
+7     2     Floppy
+7     8     Fallback_Network
+7     9     Fallback_HDD
+7     10    Fallback_Floppy
+#7     3     ROM
+#8     0     200Mhz
+#8     1     166Mhz
+#8     2     133Mhz
+#8     3     100Mhz
+#9     0     off
+#9     1     87.5%
+#9     2     75.0%
+#9     3     62.5%
+#9     4     50.0%
+#9     5     37.5%
+#9     6     25.0%
+#9     7     12.5%
+
+checksums
+
+checksum 392 983 984
+
+
diff --git a/src/mainboard/tyan/s2735/failover.c b/src/mainboard/tyan/s2735/failover.c
new file mode 100644
index 0000000000..6ba3cae62a
--- /dev/null
+++ b/src/mainboard/tyan/s2735/failover.c
@@ -0,0 +1,59 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <arch/smp/lapic.h>
+#include "pc80/mc146818rtc_early.c"
+#include "southbridge/intel/i82801er/cmos_failover.c"
+#include "cpu/p6/boot_cpu.c"
+#include "northbridge/intel/e7501/reset_test.c"
+
+#define HAVE_REGPARM_SUPPORT 0
+#if HAVE_REGPARM_SUPPORT
+static unsigned long main(unsigned long bist)
+{
+#else
+static void main(void)
+{
+	unsigned long bist = 0;
+	
+#endif
+	/* Is this a deliberate reset by the bios */
+	if (bios_reset_detected() && last_boot_normal()) {
+		goto normal_image;
+	}
+	/* This is the primary cpu how should I boot? */
+	else  {
+
+		check_cmos_failed();		
+
+		if (do_normal_boot()) {
+			goto normal_image;
+		}
+		else {
+			goto fallback_image;
+		}
+	}
+ normal_image:
+	asm volatile ("jmp __normal_image" 
+		: /* outputs */ 
+		: "a" (bist) /* inputs */
+		: /* clobbers */
+		);
+#if 0
+ cpu_reset:
+	asm volatile ("jmp __cpu_reset"
+		: /* outputs */ 
+		: "a"(bist) /* inputs */
+		: /* clobbers */
+		);
+#endif
+ fallback_image:
+#if HAVE_REGPARM_SUPPORT
+	return bist;
+#else
+	return;
+#endif
+}
diff --git a/src/mainboard/tyan/s2735/irq_tables.c b/src/mainboard/tyan/s2735/irq_tables.c
new file mode 100644
index 0000000000..b85847e9aa
--- /dev/null
+++ b/src/mainboard/tyan/s2735/irq_tables.c
@@ -0,0 +1,40 @@
+/* This file was generated by getpir.c, do not modify! 
+   (but if you do, please run checkpir on it to verify)
+   Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+   Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+	PIRQ_SIGNATURE,  /* u32 signature */
+	PIRQ_VERSION,    /* u16 version   */
+	32+16*15,	 /* there can be total 15 devices on the bus */
+	0x00,		 /* Where the interrupt router lies (bus) */
+	(0x1f<<3)|0x0,   /* Where the interrupt router lies (dev) */
+	0,		 /* IRQs devoted exclusively to PCI usage */
+	0x8086,		 /* Vendor */
+	0x24d0,		 /* Device */
+	0,		 /* Crap (miniport) */
+	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+	0x9a,         /*  u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+	{
+		/* bus,     dev|fn,   {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap},  slot, rfu */
+		{0x04,(0x08<<3)|0x0, {{0x68, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+		{0x00,(0x1f<<3)|0x0, {{0x62, 0xdcf8}, {0x61, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+		{0x00,(0x1d<<3)|0x0, {{0x60, 0xdcf8}, {0x63, 0xdcf8}, {0x62, 0xdcf8}, {0x6b, 0x0dcf8}}, 0x0, 0x0},
+		{0x04,(0x03<<3)|0x0, {{0x62, 0xdcf8}, {0x63, 0xdcf8}, {0x60, 0xdcf8}, {0x61, 0x0dcf8}}, 0x3, 0x0},
+		{0x04,(0x02<<3)|0x0, {{0x62, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+		{0x03,(0x1f<<3)|0x0, {{0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+		{0x02,(0x1f<<3)|0x0, {{0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+		{0x03,(0x03<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x1, 0x0},
+		{0x03,(0x06<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x2, 0x0},
+		{0x02,(0x01<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+		{0x02,(0x02<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+		{0x04,(0x01<<3)|0x0, {{0x61, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+		{0x04,(0x04<<3)|0x0, {{0x63, 0xdcf8}, {0x60, 0xdcf8}, {0x61, 0xdcf8}, {0x62, 0x0dcf8}}, 0x4, 0x0},
+		{0x03,(0x04<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x5, 0x0},
+		{0x03,(0x05<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x6, 0x0},
+	}
+};
diff --git a/src/mainboard/tyan/s2735/mainboard.c b/src/mainboard/tyan/s2735/mainboard.c
new file mode 100644
index 0000000000..143909f1a5
--- /dev/null
+++ b/src/mainboard/tyan/s2735/mainboard.c
@@ -0,0 +1,183 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/chip.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "chip.h"
+//#include <part/mainboard.h>
+//#include "lsi_scsi.c"
+unsigned long initial_apicid[CONFIG_MAX_CPUS] =
+{
+	0, 6, 1, 7
+};
+#if 0
+static void fixup_lsi_53c1030(struct device *pdev)
+{
+//	uint8_t byte;
+	uint16_t word;
+
+	byte = 1;
+        pci_write_config8(pdev, 0xff, byte);
+           // Set the device id 
+//      pci_write_config_word(pdev, PCI_DEVICE_ID, PCI_DEVICE_ID_LSILOGIC_53C1030);
+           // Set the subsytem vendor id 
+//      pci_write_config16(pdev, PCI_SUBSYSTEM_VENDOR_ID, PCI_VENDOR_ID_TYAN);  
+        word = 0x10f1;
+	pci_write_config16(pdev, PCI_SUBSYSTEM_VENDOR_ID, word);
+            // Set the subsytem id 
+	word = 0x2880;
+        pci_write_config16(pdev, PCI_SUBSYSTEM_ID, word);
+            // Disable writes to the device id 
+	byte = 0;
+        pci_write_config8(pdev, 0xff, byte);
+
+//	lsi_scsi_init(pdev);
+	
+}
+#endif
+//extern static void lsi_scsi_init(struct device *dev);
+#if 0
+static void print_pci_regs(struct device *dev)
+{
+      uint8_t byte;
+      int i;
+
+      for(i=0;i<256;i++) {
+	     byte = pci_read_config8(dev, i);
+   
+             if((i%16)==0) printk_info("\n%02x:",i);
+             printk_debug(" %02x",byte);
+      }
+      printk_debug("\n");
+	
+//        pci_write_config8(dev, 0x4, byte);
+
+}
+#endif
+#if 0
+static void print_mem(void)
+{
+        int i;
+	int low_1MB = 0;
+	for(i=low_1MB;i<low_1MB+1024*4;i++) {
+             if((i%16)==0) printk_debug("\n %08x:",i);
+             printk_debug(" %02x ",(unsigned char)*((unsigned char *)i));
+             }
+
+        for(i=low_1MB;i<low_1MB+1024*4;i++) {
+             if((i%16)==0) printk_debug("\n %08x:",i);
+             printk_debug(" %c ",(unsigned char)*((unsigned char *)i));
+             }
+ }
+#endif
+#if 0
+static void onboard_scsi_fixup(void)
+{
+       struct device *dev;
+	unsigned char i,j,k;
+#if 1
+	for(i=0;i<=5;i++) {
+		for(j=0;j<=0x1f;j++) {
+			for (k=0;k<=6;k++){
+				dev = dev_find_slot(i, PCI_DEVFN(j, k));
+				if (dev) {
+			                printk_debug("%02x:%02x:%02x",i,j,k);
+					print_pci_regs(dev);
+        			}
+			}
+		}
+	}
+#endif
+
+
+#if 0
+        dev = dev_find_device(PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C1030,0);
+        if(!dev) {
+                printk_info("LSI_SCSI_FW_FIXUP: No Device Found!");
+                return;
+        }
+
+	lsi_scsi_init(dev); 
+#endif
+//	print_mem();
+//	amd8111_enable_rom();
+}
+#endif
+/*
+static void vga_fixup(void) {
+        // we do this right here because:
+        // - all the hardware is working, and some VGA bioses seem to need
+        //   that
+        // - we need page 0 below for linuxbios tables.
+#if CONFIG_REALMODE_IDT == 1
+        printk_debug("INSTALL REAL-MODE IDT\n");
+        setup_realmode_idt();
+#endif
+#if CONFIG_VGABIOS == 1
+        printk_debug("DO THE VGA BIOS\n");
+        do_vgabios();
+        post_code(0x93);
+#endif
+
+}
+ */
+
+static void
+enable(struct chip *chip, enum chip_pass pass)
+{
+
+        struct mainboard_tyan_s2735_config *conf = 
+		(struct mainboard_tyan_s2735_config *)chip->chip_info;
+
+        switch (pass) {
+		default: break;
+//		case CONF_PASS_PRE_CONSOLE:
+//		case CONF_PASS_PRE_PCI:
+		case CONF_PASS_POST_PCI:		
+                case CONF_PASS_PRE_BOOT:
+//			if (conf->fixup_scsi)
+//        			onboard_scsi_fixup();
+//			if (conf->fixup_vga)
+//				vga_fixup();
+//			printk_debug("mainboard fixup pass %d done\r\n",pass);
+			break;
+	}
+
+}
+
+static int
+mainboard_scan_bus(device_t root, int maxbus)
+{
+        int retval;
+        printk_spew("%s: root %p maxbus %d\n", __FUNCTION__, root, maxbus);
+        retval = pci_scan_bus(root->bus, 0, 0xff, maxbus);
+        printk_spew("DONE %s: return %d\n", __FUNCTION__, maxbus);
+        return maxbus;
+}
+
+static struct device_operations mainboard_operations = {
+        .read_resources   = root_dev_read_resources,
+        .set_resources    = root_dev_set_resources,
+        .enable_resources = enable_childrens_resources,
+        .init             = 0,
+        .scan_bus         = mainboard_scan_bus,
+        .enable           = 0,
+};
+
+static void enumerate(struct chip *chip)
+{
+        struct chip *child;
+        dev_root.ops = &mainboard_operations;
+        chip->dev = &dev_root;
+        chip->bus = 0;
+        for(child = chip->children; child; child = child->next) {
+                child->bus = &dev_root.link[0];
+        }
+}
+struct chip_control mainboard_tyan_s2735_control = {
+        .enable = enable,
+        .enumerate = enumerate,
+        .name      = "Tyan s2735 mainboard ",
+};
+
diff --git a/src/mainboard/tyan/s2735/mptable.c b/src/mainboard/tyan/s2735/mptable.c
new file mode 100644
index 0000000000..25b1929eba
--- /dev/null
+++ b/src/mainboard/tyan/s2735/mptable.c
@@ -0,0 +1,165 @@
+#include <console/console.h>
+#include <arch/smp/mpspec.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+
+void *smp_write_config_table(void *v, unsigned long * processor_map)
+{
+        static const char sig[4] = "PCMP";
+        static const char oem[8] = "TYAN    ";
+        static const char productid[12] = "S2735       ";
+        struct mp_config_table *mc;
+
+        mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
+        memset(mc, 0, sizeof(*mc));
+
+        memcpy(mc->mpc_signature, sig, sizeof(sig));
+        mc->mpc_length = sizeof(*mc); /* initially just the header */
+        mc->mpc_spec = 0x04;
+        mc->mpc_checksum = 0; /* not yet computed */
+        memcpy(mc->mpc_oem, oem, sizeof(oem));
+        memcpy(mc->mpc_productid, productid, sizeof(productid));
+        mc->mpc_oemptr = 0;
+        mc->mpc_oemsize = 0;
+        mc->mpc_entry_count = 0; /* No entries yet... */
+        mc->mpc_lapic = LAPIC_ADDR;
+        mc->mpe_length = 0;
+        mc->mpe_checksum = 0;
+        mc->reserved = 0;
+
+        smp_write_processors(mc, processor_map);
+
+
+/*Bus:		Bus ID	Type*/
+	smp_write_bus(mc, 0, "PCI   ");
+	smp_write_bus(mc, 1, "PCI   ");
+	smp_write_bus(mc, 2, "PCI   ");
+	smp_write_bus(mc, 3, "PCI   ");
+	smp_write_bus(mc, 4, "PCI   ");
+	smp_write_bus(mc, 5, "ISA   ");
+/*I/O APICs:	APIC ID	Version	State		Address*/
+	smp_write_ioapic(mc, 8, 0x20, 0xfec00000);
+	{
+		struct pci_dev *dev;
+		uint32_t base;
+		dev = dev_find_slot(1, PCI_DEVFN(0x1e,0));
+		if (dev) {
+			base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
+			base &= PCI_BASE_ADDRESS_MEM_MASK;
+			smp_write_ioapic(mc, 9, 0x20, base);
+		}
+		dev = dev_find_slot(1, PCI_DEVFN(0x1c,0));
+		if (dev) {
+			base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
+			base &= PCI_BASE_ADDRESS_MEM_MASK;
+			smp_write_ioapic(mc, 0xa, 0x20, base);
+		}
+	}
+/*I/O Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	PIN#
+*/	
+	smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x0, 0x8, 0x0);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x1, 0x8, 0x1);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x0, 0x8, 0x2);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x3, 0x8, 0x3);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x4, 0x8, 0x4);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x6, 0x8, 0x6);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x8, 0x8, 0x8);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x9, 0x8, 0x9);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0xc, 0x8, 0xc);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0xd, 0x8, 0xd);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0xe, 0x8, 0xe);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0xf, 0x8, 0xf);
+//USB
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x7c, 0x8, 0x12);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x7d, 0x8, 0x11);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x74, 0x8, 0x10);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x75, 0x8, 0x13);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x77, 0x8, 0x17);
+
+//onboard ati
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, 0x8, 0x8, 0x12);
+
+//onboard intel 82551 10/100
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, 0x4, 0x8, 0x11);
+
+// onboard Intel 82547 1000
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x4, 0xa, 0x0);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x5, 0xa, 0x1);
+
+//Slot 4
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|0, 0x8, 0x12);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|1, 0x8, 0x13);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|2, 0x8, 0x10);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|3, 0x8, 0x11);
+//Slot 3
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|0, 0x8, 0x13);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|1, 0x8, 0x10);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|2, 0x8, 0x11);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|3, 0x8, 0x12);
+//Slot 1
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|0, 0x9, 0x0);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|1, 0x9, 0x1);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|2, 0x9, 0x2);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|3, 0x9, 0x3);
+//Slot 2
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|0, 0x9, 0x4);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|1, 0x9, 0x5);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|2, 0x9, 0x6);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|3, 0x9, 0x7);
+
+/*Local Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	PIN#*/
+	smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x0, 0x0, MP_APIC_ALL, 0x0);
+	smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x0, 0x0, MP_APIC_ALL, 0x1);
+/*
+MP Config Extended Table Entries:
+
+--
+System Address Space
+ bus ID: 0 address type: I/O address
+ address base: 0x9000
+ address range: 0x6000
+--
+System Address Space
+ bus ID: 0 address type: I/O address
+ address base: 0x0
+ address range: 0x100
+--
+System Address Space
+ bus ID: 0 address type: memory address
+ address base: 0xa0000
+ address range: 0x20000
+--
+System Address Space
+ bus ID: 0 address type: memory address
+ address base: 0xfc700000
+ address range: 0x2500000
+--
+System Address Space
+ bus ID: 0 address type: prefetch address
+ address base: 0xff600000
+ address range: 0x500000
+--
+Bus Heirarchy
+ bus ID: 5 bus info: 0x01 parent bus ID: 0--
+Compatibility Bus Address
+ bus ID: 0 address modifier: add
+ predefined range: 0x00000000--
+Compatibility Bus Address
+ bus ID: 0 address modifier: add
+ predefined range: 0x00000001	// There is no extension information... 
+*/
+	/* Compute the checksums */
+	mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
+	mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
+	printk_debug("Wrote the mp table end at: %p - %p\n",
+		mc, smp_next_mpe_entry(mc));
+	return smp_next_mpe_entry(mc);
+}
+
+unsigned long write_smp_table(unsigned long addr, unsigned long *processor_map)
+{
+	void *v;
+	v = smp_write_floating_table(addr);
+	return (unsigned long)smp_write_config_table(v, processor_map);
+}
diff --git a/src/northbridge/intel/e7501/Config.lb b/src/northbridge/intel/e7501/Config.lb
new file mode 100644
index 0000000000..f101a921fd
--- /dev/null
+++ b/src/northbridge/intel/e7501/Config.lb
@@ -0,0 +1,4 @@
+config chip.h
+object northbridge.o
+#driver misc_control.o
+
diff --git a/src/northbridge/intel/e7501/chip.h b/src/northbridge/intel/e7501/chip.h
new file mode 100644
index 0000000000..4fa6df49b3
--- /dev/null
+++ b/src/northbridge/intel/e7501/chip.h
@@ -0,0 +1,5 @@
+struct northbridge_intel_e7501_config
+{
+};
+
+extern struct chip_control northbridge_intel_e7501_control;
diff --git a/src/northbridge/intel/e7501/debug.c b/src/northbridge/intel/e7501/debug.c
new file mode 100644
index 0000000000..67670f9844
--- /dev/null
+++ b/src/northbridge/intel/e7501/debug.c
@@ -0,0 +1,164 @@
+/*
+ * generic K8 debug code, used by mainboard specific auto.c
+ *
+ */
+#if 1
+static void print_debug_pci_dev(unsigned dev)
+{
+	print_debug("PCI: ");
+	print_debug_hex8((dev >> 16) & 0xff);
+	print_debug_char(':');
+	print_debug_hex8((dev >> 11) & 0x1f);
+	print_debug_char('.');
+	print_debug_hex8((dev >> 8) & 7);
+}
+
+static void print_pci_devices(void)
+{
+	device_t dev;
+	for(dev = PCI_DEV(0, 0, 0); 
+		dev <= PCI_DEV(0, 0x1f, 0x7); 
+		dev += PCI_DEV(0,0,1)) {
+		uint32_t id;
+		id = pci_read_config32(dev, PCI_VENDOR_ID);
+		if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0x0000)) {
+			continue;
+		}
+		print_debug_pci_dev(dev);
+		print_debug("\r\n");
+	}
+}
+
+static void dump_pci_device(unsigned dev)
+{
+	int i;
+	print_debug_pci_dev(dev);
+	print_debug("\r\n");
+	
+	for(i = 0; i <= 255; i++) {
+		unsigned char val;
+		if ((i & 0x0f) == 0) {
+			print_debug_hex8(i);
+			print_debug_char(':');
+		}
+		val = pci_read_config8(dev, i);
+		print_debug_char(' ');
+		print_debug_hex8(val);
+		if ((i & 0x0f) == 0x0f) {
+			print_debug("\r\n");
+		}
+	}
+}
+
+static void dump_pci_devices(void)
+{
+	device_t dev;
+	for(dev = PCI_DEV(0, 0, 0); 
+		dev <= PCI_DEV(0, 0x1f, 0x7); 
+		dev += PCI_DEV(0,0,1)) {
+		uint32_t id;
+		id = pci_read_config32(dev, PCI_VENDOR_ID);
+		if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0x0000)) {
+			continue;
+		}
+		dump_pci_device(dev);
+	}
+}
+
+static void dump_spd_registers(const struct mem_controller *ctrl)
+{
+	int i;
+	print_debug("\r\n");
+	for(i = 0; i < 4; i++) {
+		unsigned device;
+		device = ctrl->channel0[i];
+		if (device) {
+			int j;
+			print_debug("dimm: "); 
+			print_debug_hex8(i); 
+			print_debug(".0: ");
+			print_debug_hex8(device);
+			for(j = 0; j < 256; j++) {
+				int status;
+				unsigned char byte;
+				if ((j & 0xf) == 0) {
+					print_debug("\r\n");
+					print_debug_hex8(j);
+					print_debug(": ");
+				}
+				status = smbus_read_byte(device, j);
+				if (status < 0) {
+					print_debug("bad device\r\n");
+					break;
+				}
+				byte = status & 0xff;
+				print_debug_hex8(byte);
+				print_debug_char(' ');
+			}
+			print_debug("\r\n");
+		}
+#if 0
+		device = ctrl->channel1[i];
+		if (device) {
+			int j;
+			print_debug("dimm: "); 
+			print_debug_hex8(i); 
+			print_debug(".1: ");
+			print_debug_hex8(device);
+			for(j = 0; j < 256; j++) {
+				int status;
+				unsigned char byte;
+				if ((j & 0xf) == 0) {
+					print_debug("\r\n");
+					print_debug_hex8(j);
+					print_debug(": ");
+				}
+				status = smbus_read_byte(device, j);
+				if (status < 0) {
+					print_debug("bad device\r\n");
+					break;
+				}
+				byte = status & 0xff;
+				print_debug_hex8(byte);
+				print_debug_char(' ');
+			}
+			print_debug("\r\n");
+		}
+#endif
+	}
+}
+static void dump_smbus_registers(void)
+{
+        int i;
+        print_debug("\r\n");
+        for(i = 1; i < 0x80; i++) {
+                unsigned device;
+                device = i;
+                int j;
+                print_debug("smbus: ");
+                print_debug_hex8(device);
+                for(j = 0; j < 256; j++) {
+                	int status; 
+                        unsigned char byte;
+                        if ((j & 0xf) == 0) {
+                	        print_debug("\r\n");
+                                print_debug_hex8(j);
+                                print_debug(": ");
+                        }
+                        status = smbus_read_byte(device, j);
+                        if (status < 0) {
+                                print_debug("bad device\r\n");
+                                break;
+                        }
+                        byte = status & 0xff;
+                        print_debug_hex8(byte);
+                        print_debug_char(' ');
+                }
+                print_debug("\r\n");
+	}	
+}
+#endif
diff --git a/src/northbridge/intel/e7501/e7501.h b/src/northbridge/intel/e7501/e7501.h
new file mode 100644
index 0000000000..e69de29bb2
--- /dev/null
+++ b/src/northbridge/intel/e7501/e7501.h
diff --git a/src/northbridge/intel/e7501/northbridge.c b/src/northbridge/intel/e7501/northbridge.c
new file mode 100644
index 0000000000..452166ba28
--- /dev/null
+++ b/src/northbridge/intel/e7501/northbridge.c
@@ -0,0 +1,151 @@
+#include <console/console.h>
+#include <arch/io.h>
+#include <stdint.h>
+#include <mem.h>
+#include <part/sizeram.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/chip.h>
+#include <stdlib.h>
+#include <string.h>
+#include <bitops.h>
+#include "chip.h"
+
+struct mem_range *sizeram(void)
+{
+	static struct mem_range mem[4];
+	/* the units of tolm are 64 KB */
+	/* the units of drb16 are 64 MB */
+	uint16_t tolm, remapbase, remaplimit, drb16;
+	uint16_t tolm_r, remapbase_r, remaplimit_r;
+	uint8_t  drb;
+	int remap_high;
+        device_t dev;
+
+        dev = dev_find_slot(0, 0); // d0f0
+	if (!dev) {
+                printk_err("Cannot find PCI: 0:0\n");
+                return 0;
+        }
+	
+	/* Calculate and report the top of low memory and 
+	 * any remapping.
+	 */
+	/* Test if the remap memory high option is set */
+        remap_high = 0;
+//        if(get_option(&remap_high, "remap_memory_high")){
+//                remap_high = 0;
+//        }
+	printk_debug("remap_high is %d\n", remap_high);
+	/* get out the value of the highest DRB. This tells the end of 
+	 * physical memory. The units are ticks of 64 MB i.e. 1 means
+	 * 64 MB. 
+	 */
+	drb = pci_read_config8(dev, 0x67);
+	drb16 = (uint16_t)drb;
+	if(remap_high && (drb16 > 0x08)) {
+		/* We only come here if we have at least 512MB of memory,
+		 * so it is safe to hard code tolm.
+		 * 0x2000 means 512MB 
+		 */
+
+		tolm = 0x2000;
+		/* i.e 0x40 * 0x40 is 0x1000 which is 4 GB */
+		if(drb16 > 0x0040) {
+			/* There is more than 4GB of memory put
+			 * the remap window at the end of ram.
+			 */
+			remapbase = drb16;
+			remaplimit = remapbase + 0x38;
+		}
+		else {
+			remapbase = 0x0040;
+			remaplimit = remapbase + (drb16-8);
+		}
+	}
+	else {
+		tolm = (uint16_t)((dev_root.resource[1].base >> 16)&0x0f800);
+		if((tolm>>8) >= (drb16<<2)) {
+			tolm = (drb16<<10);
+			remapbase = 0x3ff;
+			remaplimit = 0;
+		}
+		else {
+			remapbase = drb16;
+			remaplimit = remapbase + ((0x0040-(tolm>>10))-1);
+		}
+	}
+	/* Write the ram configruation registers,
+	 * preserving the reserved bits.
+	 */
+	tolm_r = pci_read_config16(dev, 0xc4);
+	tolm |= (tolm_r & 0x7ff); 
+	pci_write_config16(dev, 0xc4, tolm);
+	remapbase_r = pci_read_config16(dev, 0xc6);
+	remapbase |= (remapbase_r & 0xfc00);
+	pci_write_config16(dev, 0xc6, remapbase);
+	remaplimit_r = pci_read_config16(dev, 0xc8);
+	remaplimit |= (remaplimit_r & 0xfc00);
+	pci_write_config16(dev, 0xc8, remaplimit);
+
+#if 0
+    printk_debug("mem info tolm = %x, drb = %x, pci_memory_base = %x, remap = %x-%x\n",tolm,drb,pci_memory_base,remapbase,remaplimit);
+#endif
+	
+	mem[0].basek = 0;
+	mem[0].sizek = 640;
+	mem[1].basek = 768;
+	/* Convert size in 64K bytes to size in K bytes */
+	mem[1].sizek = (tolm << 6) - mem[1].basek;
+	mem[2].basek = 0;
+	mem[2].sizek = 0;
+	if ((drb << 16) > (tolm << 6)) {
+		/* We don't need to consider the remap window
+		 * here because we put it immediately after the
+		 * rest of ram.
+		 * All we must do is calculate the amount
+		 * of unused memory and report it at 4GB.
+		 */
+		mem[2].basek = 4096*1024;
+		mem[2].sizek = (drb << 16) - (tolm << 6);
+	}
+	mem[3].basek = 0;
+	mem[3].sizek = 0;
+	
+	return mem;
+}
+static void enumerate(struct chip *chip)
+{
+        extern struct device_operations default_pci_ops_bus;
+        chip_enumerate(chip);
+        chip->dev->ops = &default_pci_ops_bus;
+}
+#if 0
+static void northbridge_init(struct chip *chip, enum chip_pass pass)
+{
+
+        struct northbridge_intel_e7501_config *conf =
+                (struct northbridge_intel_e7501_config *)chip->chip_info;
+
+        switch (pass) {
+        case CONF_PASS_PRE_PCI:
+                break;
+
+        case CONF_PASS_POST_PCI:
+                break;
+
+        case CONF_PASS_PRE_BOOT:
+                break;
+
+        default:
+                /* nothing yet */
+                break;
+        }
+}
+#endif
+
+struct chip_control northbridge_intel_e7501_control = {
+        .enumerate = enumerate,
+//        .enable    = northbridge_init,
+        .name      = "intel E7501 Northbridge",
+};
diff --git a/src/northbridge/intel/e7501/raminit.c b/src/northbridge/intel/e7501/raminit.c
new file mode 100644
index 0000000000..09743ba5fd
--- /dev/null
+++ b/src/northbridge/intel/e7501/raminit.c
@@ -0,0 +1,2099 @@
+
+/* This was originally for the e7500, modified for e7501
+ * The primary differences are that 7501 apparently can 
+ * support single channel RAM (i haven't tested),
+ * CAS1.5 is no longer supported, The ECC scrubber
+ * now supports a mode to zero RAM and init ECC in one step
+ * and the undocumented registers at 0x80 require new 
+ * (undocumented) values determined by guesswork and
+ * comparison w/ OEM BIOS values.
+ * Steven James 02/06/2003
+ */
+
+/* converted to C 6/2004 yhlu */
+
+#define DEBUG_RAM_CONFIG 0
+
+#define dumpnorth() dump_pci_device(PCI_DEV(0, 0, 0)) 
+
+/* DDR DIMM Mode register Definitions */
+
+#define BURST_2           (1<<0)
+#define BURST_4           (2<<0)
+#define BURST_8           (3<<0)
+
+#define BURST_SEQUENTIAL  (0<<3)
+#define BURST_INTERLEAVED (1<<3)
+
+#define CAS_2_0	          (0x2<<4)
+#define CAS_3_0           (0x3<<4)
+#define CAS_1_5           (0x5<<4)
+#define CAS_2_5           (0x6<<4)
+
+#define MODE_NORM         (0 << 7)
+#define MODE_DLL_RESET    (2 << 7)
+#define MODE_TEST         (1 << 7)
+
+#define BURST_LENGTH BURST_4
+#define BURST_TYPE   BURST_INTERLEAVED
+#define CAS_LATENCY  CAS_2_0
+//#define CAS_LATENCY  CAS_2_5
+//#define CAS_LATENCY  CAS_1_5
+
+#define MRS_VALUE (MODE_NORM | CAS_LATENCY | BURST_TYPE | BURST_LENGTH)
+#define EMRS_VALUE 0x000
+
+#define MD_SHIFT 4
+
+#define RAM_COMMAND_NONE	0x0
+#define RAM_COMMAND_NOP		0x1
+#define RAM_COMMAND_PRECHARGE	0x2
+#define RAM_COMMAND_MRS		0x3
+#define RAM_COMMAND_EMRS	0x4
+#define RAM_COMMAND_CBR		0x6
+#define RAM_COMMAND_NORMAL	0x7
+
+
+static inline void do_ram_command (const struct mem_controller *ctrl, uint32_t value) {
+        uint32_t dword;
+        uint8_t byte;
+        int i;
+        uint32_t result;
+#if DEBUG_RAM_CONFIG >= 2
+        print_debug("P:");
+        print_debug_hex8(value);
+        print_debug("\r\n");
+#endif
+        /* %ecx - initial address to read from */
+        /* Compute the offset */
+        dword = value >> 16;
+        for(i=0;i<8;i++) {
+                /* Set the ram command */
+                byte = pci_read_config8(ctrl->d0, 0x7c);
+                byte &= 0x8f;
+                byte |= (uint8_t)(value & 0xff);
+                pci_write_config8(ctrl->d0, 0x7c, byte);
+
+                /* Assert the command to the memory */
+#if DEBUG_RAM_CONFIG  >= 2
+                print_debug("R:");
+                print_debug_hex32(dword);
+                print_debug("\r\n");
+#endif
+
+                result = read32(dword);
+
+                /* Go to the next base address */
+                dword += 0x04000000;
+
+        } 
+
+        /* The command has been sent to all dimms so get out */
+}
+
+
+static inline void RAM_CMD(const struct mem_controller *ctrl, uint32_t command, uint32_t offset)  {
+	uint32_t value = 	((offset) << (MD_SHIFT + 16))|((command << 4) & 0x70) ; 
+	do_ram_command(ctrl, value);
+}
+	
+#define RAM_NOP(ctrl)		RAM_CMD(ctrl, RAM_COMMAND_NOP, 0)
+#define RAM_PRECHARGE(ctrl)		RAM_CMD(ctrl, RAM_COMMAND_PRECHARGE, 0)
+#define RAM_CBR(ctrl)		RAM_CMD(ctrl, RAM_COMMAND_CBR, 0)
+#define RAM_EMRS(ctrl)		RAM_CMD(ctrl, RAM_COMMAND_EMRS, EMRS_VALUE)
+
+static const uint8_t ram_cas_latency[] = {
+	CAS_2_5, CAS_2_0, CAS_1_5, CAS_2_5
+	};
+
+static inline void ram_mrs(const struct mem_controller *ctrl, uint32_t value){
+	/* Read the cas latency setting */
+	uint8_t byte;
+	uint32_t dword;
+	byte = pci_read_config8(ctrl->d0, 0x78); 
+	/* Transform it into the form expected by SDRAM */
+	dword = ram_cas_latency[(byte>>4) & 3];
+
+	value  |= (dword<<(16+MD_SHIFT));
+	
+	value |= (MODE_NORM | BURST_TYPE | BURST_LENGTH) << (16+MD_SHIFT);
+
+	do_ram_command(ctrl, value);
+}
+
+#define RAM_MRS(ctrl, dll_reset) ram_mrs( ctrl, (dll_reset << (8+MD_SHIFT+ 16)) | ((RAM_COMMAND_MRS <<4)& 0x70) )
+
+static void RAM_NORMAL(const struct mem_controller *ctrl) {
+	uint8_t byte;
+	byte = pci_read_config8(ctrl->d0, 0x7c);
+	byte &=  0x8f;
+	byte |= (RAM_COMMAND_NORMAL << 4);
+	pci_write_config8(ctrl->d0, 0x7c, byte);
+}
+
+static void  RAM_RESET_DDR_PTR(const struct mem_controller *ctrl) {
+	uint8_t byte;
+	byte = pci_read_config8(ctrl->d0, 0x88);
+	byte |= (1 << 4 );
+	pci_write_config8(ctrl->d0, 0x88, byte);
+	byte = pci_read_config8(ctrl->d0, 0x88);
+	byte &= ~(1 << 4);
+	pci_write_config8(ctrl->d0, 0x88, byte);
+}
+
+static void ENABLE_REFRESH(const struct mem_controller *ctrl) 
+{
+	uint32_t dword;
+	dword = pci_read_config32(ctrl->d0, 0x7c);
+	dword |= (1 << 29);
+	pci_write_config32(ctrl->d0, 0x7c, dword);
+}
+
+	/*
+	 * Table:	constant_register_values
+	 */
+static const long register_values[] = {
+	/* SVID - Subsystem Vendor Identification Register
+	 * 0x2c - 0x2d
+	 * [15:00] Subsytem Vendor ID (Indicates system board vendor)
+	 */
+	/* SID - Subsystem Identification Register
+	 * 0x2e - 0x2f
+	 * [15:00] Subsystem ID
+	 */
+	 0x2c, 0, (0x15d9 << 0) | (0x3580 << 16),
+
+	/* Undocumented
+	 * 0x80 - 0x80
+	 * This register has something to do with CAS latencies,
+	 * possibily this is the real chipset control.
+	 * At 0x00 CAS latency 1.5 works.
+	 * At 0x06 CAS latency 2.5 works.
+	 * At 0x01 CAS latency 2.0 works.
+	 */
+	/* This is still undocumented in e7501, but with different values
+	 * CAS 2.0 values taken from Intel BIOS settings, others are a guess
+	 * and may be terribly wrong. Old values preserved as comments until I
+	 * figure this out for sure.
+	 * e7501 docs claim that CAS1.5 is unsupported, so it may or may not 
+	 * work at all.
+	 * Steven James 02/06/2003
+	 */
+#if CAS_LATENCY == CAS_2_5
+//	0x80, 0xfffffe00, 0x06 /* Intel E7500 recommended */
+	0x80, 0xfffff000, 0x0662, /* from Factory Bios */
+#elif CAS_LATENCY == CAS_2_0
+//	0x80, 0xfffffe00, 0x0d /* values for register 0x80 */
+	0x80, 0xfffff000, 0x0bb1, /* values for register 0x80 */
+#endif
+
+	/* Enable periodic memory recalibration */
+	0x88, 0xffffff00, 0x80,
+
+	/* FDHC - Fixed DRAM Hole Control
+	 * 0x58
+	 * [7:7] Hole_Enable
+	 *       0 == No memory Hole
+	 *       1 == Memory Hole from 15MB to 16MB
+	 * [6:0] Reserved
+	 *
+	 * PAM - Programmable Attribute Map
+	 * 0x59 [1:0] Reserved
+	 * 0x59 [5:4] 0xF0000 - 0xFFFFF
+	 * 0x5A [1:0] 0xC0000 - 0xC3FFF
+	 * 0x5A [5:4] 0xC4000 - 0xC7FFF
+	 * 0x5B [1:0] 0xC8000 - 0xCBFFF
+	 * 0x5B [5:4] 0xCC000 - 0xCFFFF
+	 * 0x5C [1:0] 0xD0000 - 0xD3FFF
+	 * 0x5C [5:4] 0xD4000 - 0xD7FFF
+	 * 0x5D [1:0] 0xD8000 - 0xDBFFF
+	 * 0x5D [5:4] 0xDC000 - 0xDFFFF
+	 * 0x5E [1:0] 0xE0000 - 0xE3FFF
+	 * 0x5E [5:4] 0xE4000 - 0xE7FFF
+	 * 0x5F [1:0] 0xE8000 - 0xEBFFF
+	 * 0x5F [5:4] 0xEC000 - 0xEFFFF
+	 *       00 == DRAM Disabled (All Access go to memory mapped I/O space)
+	 *       01 == Read Only (Reads to DRAM, Writes to memory mapped I/O space)
+	 *       10 == Write Only (Writes to DRAM, Reads to memory mapped I/O space)
+	 *       11 == Normal (All Access go to DRAM)
+	 */
+	0x58, 0xcccccf7f, (0x00 << 0) | (0x30 << 8) | (0x33 << 16) | (0x33 << 24),
+	0x5C, 0xcccccccc, (0x33 << 0) | (0x33 << 8) | (0x33 << 16) | (0x33 << 24),
+
+	/* DRB - DRAM Row Boundary Registers
+	 * 0x60 - 0x6F
+	 *     An array of 8 byte registers, which hold the ending
+	 *     memory address assigned  to each pair of DIMMS, in 64MB 
+	 *     granularity.   
+	 */
+	/* Conservatively say each row has 64MB of ram, we will fix this up later */
+	0x60, 0x00000000, (0x01 << 0) | (0x02 << 8) | (0x03 << 16) | (0x04 << 24),
+	0x64, 0x00000000, (0x05 << 0) | (0x06 << 8) | (0x07 << 16) | (0x08 << 24),
+	0x68, 0xffffffff, 0,
+	0x6C, 0xffffffff, 0,
+
+	/* DRA - DRAM Row Attribute Register 
+	 * 0x70 Row 0,1
+	 * 0x71 Row 2,3
+ 	 * 0x72 Row 4,5
+	 * 0x73 Row 6,7
+	 * [7:7] Device width for Odd numbered rows
+	 *       0 == 8 bits wide x8
+	 *       1 == 4 bits wide x4
+	 * [6:4] Row Attributes for Odd numbered rows
+	 *       010 == 8KB
+	 *       011 == 16KB
+	 *       100 == 32KB
+	 *       101 == 64KB
+	 *       Others == Reserved
+	 * [3:3] Device width for Even numbered rows
+	 *       0 == 8 bits wide x8
+	 *       1 == 4 bits wide x4
+	 * [2:0] Row Attributes for Even numbered rows
+	 *       010 == 8KB
+	 *       011 == 16KB
+	 *       100 == 32KB
+	 *       101 == 64KB (This page size appears broken)
+	 *       Others == Reserved
+	 */
+	0x70, 0x00000000, 
+		(((0<<3)|(0<<0))<< 0) | 
+		(((0<<3)|(0<<0))<< 4) | 
+		(((0<<3)|(0<<0))<< 8) | 
+		(((0<<3)|(0<<0))<<12) | 
+		(((0<<3)|(0<<0))<<16) | 
+		(((0<<3)|(0<<0))<<20) | 
+		(((0<<3)|(0<<0))<<24) | 
+		(((0<<3)|(0<<0))<<28),
+	0x74, 0xffffffff, 0,
+
+	/* DRT - DRAM Time Register
+	 * 0x78
+	 * [31:30] Reserved
+	 * [29:29] Back to Back Write-Read Turn Around
+	 *         0 == 3 clocks between WR-RD commands
+	 *         1 == 2 clocks between WR-RD commands
+	 * [28:28] Back to Back Read-Write Turn Around
+	 *         0 == 5 clocks between RD-WR commands
+	 *         1 == 4 clocks between RD-WR commands
+	 * [27:27] Back to Back Read Turn Around
+	 *         0 == 4 clocks between RD commands
+	 *         1 == 3 clocks between RD commands
+	 * [26:24] Read Delay (tRD)
+	 *         000 == 7 clocks
+	 *         001 == 6 clocks
+	 *         010 == 5 clocks
+	 *         Others == Reserved
+	 * [23:19] Reserved
+	 * [18:16] DRAM idle timer
+	 *	000 == infinite
+	 *	011 == 16 dram clocks
+	 *	001 == Datasheet says reserved, but Intel BIOS sets it
+	 * [15:11] Reserved
+	 * [10:09] Active to Precharge (tRAS)
+	 *         00 == 7 clocks
+	 *         01 == 6 clocks
+	 *         10 == 5 clocks
+	 *         11 == Reserved
+	 * [08:06] Reserved
+	 * [05:04] Cas Latency (tCL)
+	 *         00 == 2.5 Clocks
+	 *         01 == 2.0 Clocks
+	 *         10 == 1.5 Clocks
+	 *         11 == Reserved
+	 * [03:03] Write Ras# to Cas# Delay (tRCD)
+	 *         0 == 3 DRAM Clocks
+	 *         1 == 2 DRAM Clocks
+ 	 * [02:01] Read RAS# to CAS# Delay (tRCD)
+ 	 *         00 == reserved
+ 	 *         01 == reserved
+	 *         10 == 3 DRAM Clocks
+	 *         11 == 2 DRAM Clocks
+	 * [00:00] DRAM RAS# to Precharge (tRP)
+	 *         0 == 3 DRAM Clocks
+	 *         1 == 2 DRAM Clocks
+	 */
+#define DRT_CAS_2_5 (0<<4)
+#define DRT_CAS_2_0 (1<<4)   
+#define DRT_CAS_1_5 (2<<4)
+#define DRT_CAS_MASK (3<<4)
+
+#if CAS_LATENCY == CAS_2_5
+#define DRT_CL DRT_CAS_2_5
+#elif CAS_LATENCY == CAS_2_0
+#define DRT_CL DRT_CAS_2_0
+#elif CAS_LATENCY == CAS_1_5
+#define DRT_CL DRT_CAS_1_5
+#endif
+
+	/* Most aggressive settings possible */
+//	0x78, 0xc0fff8c4, (1<<29)|(1<<28)|(1<<27)|(2<<24)|(2<<9)|DRT_CL|(1<<3)|(1<<1)|(1<<0),
+//	0x78, 0xc0f8f8c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|DRT_CL|(1<<3)|(3<<1)|(1<<0),
+	0x78, 0xc0f8f9c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|DRT_CL|(1<<3)|(3<<1)|(1<<0),
+
+	/* FIXME why was I attempting to set a reserved bit? */
+	/* 0x0100040f */
+
+	/* DRC - DRAM Contoller Mode Register
+	 * 0x7c
+	 * [31:30] Reserved
+	 * [29:29] Initialization Complete
+	 *         0 == Not Complete
+	 *         1 == Complete
+	 * [28:23] Reserved
+	 * [22:22]	   Channels
+	 * 		0 == Single channel
+	 *		1 == Dual Channel
+	 * [21:20] DRAM Data Integrity Mode
+	 *         00 == Disabled, no ECC
+	 *         01 == Reserved
+	 *         10 == Error checking, using chip-kill, with correction
+	 *         11 == Reserved
+	 * [19:18] Reserved
+	 *         Must equal 01
+	 * [17:17] (Intel Undocumented)	should always be set to 1
+	 * [16:16] Command Per Clock - Address/Control Assertion Rule (CPC)
+	 *         0 == 2n Rule
+	 *         1 == 1n rule
+	 * [15:11] Reserved
+	 * [10:08] Refresh mode select
+	 *         000 == Refresh disabled
+	 *         001 == Refresh interval 15.6 usec
+	 *         010 == Refresh interval 7.8 usec
+	 *         011 == Refresh interval 64 usec
+	 *         111 == Refresh every 64 clocks (fast refresh)
+	 * [07:07] Reserved
+	 * [06:04] Mode Select (SMS)
+	 *         000 == Self Refresh Mode
+	 *         001 == NOP Command
+	 *         010 == All Banks Precharge
+	 *         011 == Mode Register Set
+ 	 *         100 == Extended Mode Register Set
+	 *         101 == Reserved
+	 *         110 == CBR Refresh
+	 *         111 == Normal Operation
+	 * [03:00] Reserved
+	 */
+//	.long 0x7c, 0xffcefcff, (1<<22)|(2 << 20)|(1 << 16)| (0 << 8),
+//	.long 0x7c, 0xff8cfcff, (1<<22)|(2 << 20)|(1 << 17)|(1 << 16)| (0 << 8),
+//	.long 0x7c, 0xff80fcff, (1<<22)|(2 << 20)|(1 << 18)|(1 << 17)|(1 << 16)| (0 << 8),
+	0x7c, 0xff82fcff, (1<<22)|(2 << 20)|(1 << 18)|(1 << 16)| (0 << 8),
+
+
+	/* Another Intel undocumented register */
+	0x88, 0x080007ff, (1<<31)|(1 << 30)|(1<<28)|(0 << 26)|(0x10 << 21)|(10 << 16)|(0x13 << 11),
+
+	/* CLOCK_DIS - CK/CK# Disable Register
+	 * 0x8C
+	 * [7:4] Reserved
+	 * [3:3] CK3
+	 *       0 == Enable
+	 *       1 == Disable
+	 * [2:2] CK2
+	 *       0 == Enable
+	 *       1 == Disable
+	 * [1:1] CK1
+	 *       0 == Enable
+	 *       1 == Disable
+	 * [0:0] CK0
+	 *       0 == Enable
+	 *       1 == Disable
+	 */
+	0x8C, 0xfffffff0, 0xf,
+
+	/* TOLM - Top of Low Memory Register
+	 * 0xC4 - 0xC5
+	 * [15:11] Top of low memory (TOLM)
+	 *         The address below 4GB that should be treated as RAM,
+	 *         on a 128MB granularity.
+	 * [10:00] Reserved
+	 */
+	/* REMAPBASE - Remap Base Address Regsiter
+	 * 0xC6 - 0xC7
+	 * [15:10] Reserved
+	 * [09:00] Remap Base Address [35:26] 64M aligned
+	 *         Bits [25:0] are assumed to be 0.
+	 */
+	0xc4, 0xfc0007ff, (0x2000 << 0) | (0x3ff << 16),
+	/* REMAPLIMIT - Remap Limit Address Register
+	 * 0xC8 - 0xC9
+	 * [15:10] Reserved
+	 * [09:00] Remap Limit Address [35:26] 64M aligned
+	 * When remaplimit < remapbase this register is disabled.
+	 */
+	0xc8, 0xfffffc00, 0,
+
+	/* DVNP - Device Not Present Register
+	 * 0xE0 - 0xE1
+	 * [15:05] Reserved
+ 	 * [04:04] Device 4 Function 1 Present
+	 *         0 == Present
+	 *         1 == Absent
+ 	 * [03:03] Device 3 Function 1 Present
+	 *         0 == Present
+	 *         1 == Absent
+ 	 * [02:02] Device 2 Function 1 Present
+	 *         0 == Present
+	 *         1 == Absent
+ 	 * [01:01] Reserved
+ 	 * [00:00] Device 0 Function 1 Present
+	 *         0 == Present
+	 *         1 == Absent
+	 */
+	0xe0, 0xffffffe2, (1<<4)|(1<<3)|(1<<2)|(0<<0),
+	0xd8, 0xffff9fff, 0x00000000,
+	0xf4, 0x3f8ffffd, 0x40300002,
+	0x1050, 0xffffffcf, 0x00000030,
+};
+
+
+	/*
+	 * Routine:	ram_set_registers
+	 * Arguments:	none
+	 * Results:	none
+	 * Trashed:	%eax, %ebx, %ecx, %edx, %esi, %eflags
+	 * Effects:	Do basic ram setup that does not depend on serial
+	 *		presence detect information.
+	 *		This sets PCI configuration registers to known good
+	 *		values based on the table: 
+	 *			constant_register_values
+	 *		Which are a triple of configuration regiser, mask, and value.
+	 *		
+	 */
+/* from 1M or 512K */
+#define RCOMP_MMIO 0x100000
+
+	/* DDR RECOMP table */
+
+static const long ddr_rcomp_1[] = {
+	0x44332211, 0xc9776655, 0xffffffff, 0xffffffff,
+	0x22111111, 0x55444332, 0xfffca876, 0xffffffff,
+};
+static const long ddr_rcomp_2[] = {
+	0x00000000, 0x76543210, 0xffffeca8, 0xffffffff,
+	0x21000000, 0xa8765432, 0xffffffec, 0xffffffff,
+};
+static const long ddr_rcomp_3[] = {
+	0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
+	0x88888888, 0x88888888, 0x88888888, 0x88888888,
+};
+
+#define rcomp_init_str "Setting RCOMP registers.\r\n"
+
+static void write_8dwords(uint32_t src_addr, uint32_t dst_addr) {
+	int i;
+	uint32_t dword;
+	for(i=0;i<8;i++) {
+		dword = read32(src_addr);
+		write32(dst_addr, dword);
+		src_addr+=4;
+		dst_addr+=4;
+		
+	}
+}
+
+//#define SLOW_DOWN_IO inb(0x80);
+#define SLOW_DOWN_IO udelay(40);
+
+static void ram_set_rcomp_regs(const struct mem_controller *ctrl) {
+	uint32_t dword;
+#if DEBUG_RAM_CONFIG
+	print_debug(rcomp_init_str);
+#endif
+
+	/*enable access to the rcomp bar */
+	dword = pci_read_config32(ctrl->d0, 0x0f4);
+        dword &= ~(1<<31);
+        dword |=((1<<30)|1<<22);
+        pci_write_config32(ctrl->d0, 0x0f4, dword);
+        
+
+	/* Set the MMIO address to 512K */
+        pci_write_config32(ctrl->d0, 0x14, RCOMP_MMIO);
+
+	dword = read32(RCOMP_MMIO + 0x20);
+	dword |= (1<<9);
+	write32(RCOMP_MMIO + 0x20, dword);
+	
+
+	/* Begin to write the RCOMP registers */
+	
+	write8(RCOMP_MMIO + 0x2c, 0xff);
+	write32(RCOMP_MMIO + 0x30, 0x01040444);
+	write8(RCOMP_MMIO + 0x34, 0x04);
+	write32(RCOMP_MMIO + 0x40, 0);
+	write16(RCOMP_MMIO + 0x44, 0);
+	write16(RCOMP_MMIO + 0x48, 0);
+	write16(RCOMP_MMIO + 0x50, 0);
+	write_8dwords((uint32_t)ddr_rcomp_1, RCOMP_MMIO + 0x60);
+	write_8dwords((uint32_t)ddr_rcomp_2, RCOMP_MMIO + 0x80);
+	write_8dwords((uint32_t)ddr_rcomp_2, RCOMP_MMIO + 0xa0);
+	write_8dwords((uint32_t)ddr_rcomp_2, RCOMP_MMIO + 0x140);
+	write_8dwords((uint32_t)ddr_rcomp_2, RCOMP_MMIO + 0x1c0);
+	write_8dwords((uint32_t)ddr_rcomp_3, RCOMP_MMIO + 0x180);
+
+#if 0	/* Print the RCOMP registers */
+	movl    $RCOMP_MMIO, %ecx
+1:	movl	%ecx, %eax
+	andb	$0x0f, %al
+	jnz	2f
+	CONSOLE_INFO_TX_CHAR($'\r')
+        CONSOLE_INFO_TX_CHAR($'\n')
+	CONSOLE_INFO_TX_HEX32(%ecx)
+	CONSOLE_INFO_TX_CHAR($' ')
+	CONSOLE_INFO_TX_CHAR($'-')
+	CONSOLE_INFO_TX_CHAR($' ')
+2:	movl    (%ecx), %eax
+	CONSOLE_INFO_TX_HEX32(%eax)
+	CONSOLE_INFO_TX_CHAR($' ')
+	addl	$4, %ecx
+	cmpl	$(RCOMP_MMIO + 0x1e0), %ecx
+	jnz	1b
+        CONSOLE_INFO_TX_CHAR($'\r')
+        CONSOLE_INFO_TX_CHAR($'\n')
+#endif
+
+	dword = read32(RCOMP_MMIO + 0x20);
+	dword &= ~(3);
+	dword |= 1;
+	write32(RCOMP_MMIO + 0x20, dword);
+
+	/* Wait 40 usec */
+	SLOW_DOWN_IO;
+	
+	/* unblock updates */
+	dword = read32(RCOMP_MMIO + 0x20);
+	dword &= ~(1<<9);
+	write32(RCOMP_MMIO+0x20, dword);
+	dword |= (1<<8);
+	write32(RCOMP_MMIO+0x20, dword);
+	dword &= ~(1<<8);
+	write32(RCOMP_MMIO+0x20, dword);
+	
+	/* Wait 40 usec */
+	SLOW_DOWN_IO;
+
+	/*disable access to the rcomp bar */
+	dword = pci_read_config32(ctrl->d0, 0x0f4);
+	dword &= ~(1<<22);
+	pci_write_config32(ctrl->d0, 0x0f4, dword);	
+
+}
+
+static void ram_set_d0f0_regs(const struct mem_controller *ctrl) {
+#if DEBUG_RAM_CONFIG
+	dumpnorth();
+#endif
+	int i;
+	int max;
+        max = sizeof(register_values)/sizeof(register_values[0]);
+        for(i = 0; i < max; i += 3) {
+                uint32_t reg;
+#if DEBUG_RAM_CONFIG
+                print_debug_hex32(register_values[i]);
+                print_debug(" <-");
+                print_debug_hex32(register_values[i+2]);
+                print_debug("\r\n");
+#endif
+                reg = pci_read_config32(ctrl->d0,register_values[i]);
+                reg &= register_values[i+1];
+                reg |= register_values[i+2] & ~(register_values[i+1]);
+                pci_write_config32(ctrl->d0,register_values[i], reg);
+
+
+        }
+#if DEBUG_RAM_CONFIG
+	dumpnorth();
+#endif
+}
+static void sdram_set_registers(const struct mem_controller *ctrl){
+        ram_set_rcomp_regs(ctrl);
+        ram_set_d0f0_regs(ctrl);
+}
+
+
+	/*
+	 * Routine:	sdram_spd_get_page_size
+	 * Arguments:	%bl SMBUS_MEM_DEVICE
+	 * Results:	
+	 *		%edi log base 2 page size of DIMM side 1 in bits
+	 *		%esi log base 2 page size of DIMM side 2 in bits
+	 *
+	 * Preserved:	%ebx (except %bh), %ebp
+	 *
+	 * Trashed:	%eax, %bh, %ecx, %edx, %esp, %eflags
+	 * Used:	%eax, %ebx, %ecx, %edx, %esi, %edi, %esp, %eflags
+	 *
+	 * Effects:	Uses serial presence detect to set %edi & %esi
+	 *		to the page size of a dimm.
+	 * Notes:
+	 *              %bl SMBUS_MEM_DEVICE
+	 *              %edi holds the page size for the first side of the DIMM.
+	 *		%esi holds the page size for the second side of the DIMM.
+	 *		     memory size is represent as a power of 2.
+	 *
+	 *		This routine may be worth moving into generic code somewhere.
+	 */
+struct dimm_page_size { 
+        unsigned long side1;
+        unsigned long side2;
+};      
+  
+static struct dimm_page_size sdram_spd_get_page_size(unsigned device) {
+
+	uint32_t ecx;
+	int value;
+	struct dimm_page_size pgsz;
+
+	pgsz.side1 = 0;
+	pgsz.side2 = 0;	
+		
+	value  = spd_read_byte(device, 4); /* columns */
+	if(value < 0) goto hw_err;
+	pgsz.side1 = value & 0xf;
+	
+	/* Get the module data width and convert it to a power of two */
+	value = spd_read_byte(device,7);		/* (high byte) */
+	if(value < 0) goto hw_err;
+	ecx = value & 0xff;
+	ecx <<= 8;
+
+	value = spd_read_byte(device, 6);	 /* (low byte) */
+	if(value < 0) goto hw_err;
+	ecx |= (value & 0xff);
+
+	pgsz.side1 += log2(ecx);	 /* compute cheap log base 2 */	
+
+	/* side two */
+	value = spd_read_byte(device, 5);	/* number of physical banks */
+	if(value < 0) goto hw_err;
+	if(value==1) goto out;
+	if(value!=2) goto val_err;
+
+	/* Start with the symmetrical case */
+	pgsz.side2 = pgsz.side1;
+	value = spd_read_byte(device,4);   /* columns */
+	if(value < 0) goto hw_err;
+	if((value & 0xf0)==0 ) goto out;
+	pgsz.side2 -=value & 0xf; /* Subtract out columns on side 1 */
+	pgsz.side2 +=(value>>4)& 0xf; /* Add in columns on side 2 */
+        goto out;
+
+ val_err:
+        die("Bad SPD value\r\n");
+        /* If an hw_error occurs report that I have no memory */
+hw_err:
+	pgsz.side1 = 0;
+	pgsz.side2 = 0;
+out:
+	return pgsz;	
+}
+
+
+	/*
+	 * Routine:	sdram_spd_get_width
+	 * Arguments:	%bl SMBUS_MEM_DEVICE
+	 * Results:	
+	 *		%edi width of SDRAM chips on DIMM side 1 in bits
+	 *		%esi width of SDRAM chips on DIMM side 2 in bits
+	 *
+	 * Preserved:	%ebx (except %bh), %ebp
+	 *
+	 * Trashed:	%eax, %bh, %ecx, %edx, %esp, %eflags
+	 * Used:	%eax, %ebx, %ecx, %edx, %esi, %edi, %esp, %eflags
+	 *
+	 * Effects:	Uses serial presence detect to set %edi & %esi
+	 *		to the width of a dimm.
+	 * Notes:
+	 *              %bl SMBUS_MEM_DEVICE
+	 *              %edi holds the width for the first side of the DIMM.
+	 *		%esi holds the width for the second side of the DIMM.
+	 *		     memory size is represent as a power of 2.
+	 *
+	 *		This routine may be worth moving into generic code somewhere.
+	 */
+struct dimm_width {
+        unsigned side1;
+        unsigned side2;
+};      
+  
+static struct dimm_width sdram_spd_get_width(unsigned device) {
+	int value;
+	struct dimm_width wd;
+	uint32_t ecx;
+	
+	wd.side1 = 0;
+	wd.side2 = 0;
+
+	value = spd_read_byte(device, 13); /* sdram width */
+	if(value < 0 )  goto hw_err;
+	ecx = value;
+	
+	wd.side1 = value & 0x7f;	
+	
+	/* side two */
+	value = spd_read_byte(device, 5); /* number of physical banks */
+	if(value < 0 ) goto hw_err;	
+	if(value <=1 ) goto out;
+
+	/* Start with the symmetrical case */
+	wd.side2 = wd.side1;
+
+	if((ecx & 0x80)==0) goto out;
+	
+	wd.side2 <<=1;
+hw_err:
+	wd.side1 = 0;
+	wd.side2 = 0;
+
+ out:
+        return wd;
+}
+	
+	/*
+	 * Routine:	sdram_spd_get_dimm_size
+	 * Arguments:	%bl SMBUS_MEM_DEVICE
+	 * Results:	
+	 *		%edi log base 2 size of DIMM side 1 in bits
+	 *		%esi log base 2 size of DIMM side 2 in bits
+	 *
+	 * Preserved:	%ebx (except %bh), %ebp
+	 *
+	 * Trashed:	%eax, %bh, %ecx, %edx, %esp, %eflags
+	 * Used:	%eax, %ebx, %ecx, %edx, %esi, %edi, %esp, %eflags
+	 *
+	 * Effects:	Uses serial presence detect to set %edi & %esi
+	 *		the size of a dimm.
+	 * Notes:
+	 *              %bl SMBUS_MEM_DEVICE
+	 *              %edi holds the memory size for the first side of the DIMM.
+	 *		%esi holds the memory size for the second side of the DIMM.
+	 *		     memory size is represent as a power of 2.
+	 *
+	 *		This routine may be worth moving into generic code somewhere.
+	 */
+
+struct dimm_size {
+        unsigned long side1;
+        unsigned long side2;
+};
+
+static struct dimm_size spd_get_dimm_size(unsigned device)
+{
+        /* Calculate the log base 2 size of a DIMM in bits */
+        struct dimm_size sz;
+        int value, low;
+        sz.side1 = 0;
+        sz.side2 = 0;
+
+        /* Note it might be easier to use byte 31 here, it has the DIMM size as
+         * a multiple of 4MB.  The way we do it now we can size both
+         * sides of an assymetric dimm.
+         */
+        value = spd_read_byte(device, 3);       /* rows */
+        if (value < 0) goto hw_err;
+//        if ((value & 0xf) == 0) goto val_err;
+        sz.side1 += value & 0xf;
+
+        value = spd_read_byte(device, 4);       /* columns */
+        if (value < 0) goto hw_err;
+//        if ((value & 0xf) == 0) goto val_err;
+        sz.side1 += value & 0xf;
+
+        value = spd_read_byte(device, 17);      /* banks */
+        if (value < 0) goto hw_err;
+//        if ((value & 0xff) == 0) goto val_err;
+	value &=0xff;
+        sz.side1 += log2(value);
+
+        /* Get the module data width and convert it to a power of two */
+        value = spd_read_byte(device, 7);       /* (high byte) */
+        if (value < 0) goto hw_err;
+        value &= 0xff;
+        value <<= 8;
+        
+        low = spd_read_byte(device, 6); /* (low byte) */
+        if (low < 0) goto hw_err;
+        value |= (low & 0xff);
+//        if ((value != 72) && (value != 64)) goto val_err;
+        sz.side1 += log2(value);
+        
+        /* side 2 */
+        value = spd_read_byte(device, 5);       /* number of physical banks */
+        if (value < 0) goto hw_err;
+        if (value == 1) goto out;
+//        if (value != 2) goto val_err;
+
+        /* Start with the symmetrical case */
+        sz.side2 = sz.side1;
+
+        value = spd_read_byte(device, 3);       /* rows */
+        if (value < 0) goto hw_err;
+        if ((value & 0xf0) == 0) goto out;      /* If symmetrical we are done */
+        sz.side2 -= (value & 0x0f);             /* Subtract out rows on side 1 */
+        sz.side2 += ((value >> 4) & 0x0f);      /* Add in rows on side 2 */
+
+        value = spd_read_byte(device, 4);       /* columns */
+        if (value < 0) goto hw_err;
+//        if ((value & 0xff) == 0) goto val_err;
+        sz.side2 -= (value & 0x0f);             /* Subtract out columns on side 1 */
+        sz.side2 += ((value >> 4) & 0x0f);      /* Add in columsn on side 2 */
+        goto out;
+
+ val_err:
+        die("Bad SPD value\r\n");
+        /* If an hw_error occurs report that I have no memory */
+hw_err:
+        sz.side1 = 0;
+        sz.side2 = 0;
+ out:
+        return sz;
+}
+
+
+
+	/*
+	 * This is a place holder fill this out
+	 * Routine:	spd_set_row_attributes 
+	 * Arguments:	%bl SMBUS_MEM_DEVICE
+	 * Results:	
+	 *		%edi log base 2 size of DIMM side 1 in bits
+	 *		%esi log base 2 size of DIMM side 2 in bits
+	 *
+	 * Preserved:	%ebx (except %bh), %ebp
+	 *
+	 * Trashed:	%eax, %bh, %ecx, %edx, %esp, %eflags
+	 * Used:	%eax, %ebx, %ecx, %edx, %esi, %edi, %esp, %eflags
+	 *
+	 * Effects:	Uses serial presence detect to set %edi & %esi
+	 *		the size of a dimm.
+	 * Notes:
+	 *              %bl SMBUS_MEM_DEVICE
+	 *              %edi holds the memory size for the first side of the DIMM.
+	 *		%esi holds the memory size for the second side of the DIMM.
+	 *		     memory size is represent as a power of 2.
+	 *
+	 *		This routine may be worth moving into generic code somewhere.
+	 */
+static long spd_set_row_attributes(const struct mem_controller *ctrl, long dimm_mask) {
+	int i;  
+        uint32_t dword=0;
+        int value;
+        
+
+        /* Walk through all dimms and find the interesection of the support
+         * for ecc sdram and refresh rates
+         */        
+        
+ 
+        for(i = 0; i < DIMM_SOCKETS; i++) {
+		if (!(dimm_mask & (1 << i))) {
+                        continue;
+                }
+                 /* Test to see if I have ecc sdram */
+		struct dimm_page_size sz;
+                sz = sdram_spd_get_page_size(ctrl->channel0[i]);  /* SDRAM type */
+#if DEBUG_RAM_CONFIG
+		print_debug("page size =");
+		print_debug_hex32(sz.side1);
+		print_debug(" ");
+		print_debug_hex32(sz.side2);
+		print_debug("\r\n");
+#endif
+	
+		/* Test to see if the dimm is present */
+		if( sz.side1 !=0) {
+
+			/* Test for a valid dimm width */
+			if((sz.side1 <15) || (sz.side1>18) ) {
+				print_err("unsupported page size\r\n");
+			}
+
+	 		/* double because I have 2 channels */
+			sz.side1++;
+
+			/* Convert to the format needed for the DRA register */
+			sz.side1-=14;	
+
+			/* Place in the %ebp the dra place holder */ //i
+			dword |= sz.side1<<(i<<3);
+			
+			/* Test to see if the second side is present */
+
+	                if( sz.side2 !=0) {
+        
+	                        /* Test for a valid dimm width */
+        	                if((sz.side2 <15) || (sz.side2>18) ) {
+                	                print_err("unsupported page size\r\n");
+                        	}
+
+                        	/* double because I have 2 channels */
+                        	sz.side2++;
+
+                        	/* Convert to the format needed for the DRA register */
+                        	sz.side2-=14;
+
+	                        /* Place in the %ebp the dra place holder */ //i
+        	                dword |= sz.side2<<((i<<3) + 4 );
+
+			}
+		}
+
+		/* Now add the SDRAM chip width to the DRA */
+		struct dimm_width wd;
+		wd = sdram_spd_get_width(ctrl->channel0[i]);
+
+#if DEBUG_RAM_CONFIG
+                print_debug("width =");
+                print_debug_hex32(wd.side1);
+                print_debug(" ");
+                print_debug_hex32(wd.side2);
+                print_debug("\r\n");
+#endif
+		
+		if(wd.side1 == 0) continue;
+		if(wd.side1 == 4) {
+			/* Enable an x4 device */
+			dword |= 0x08 << (i<<3);
+		}
+
+		if(wd.side2 == 0) continue;
+                if(wd.side2 == 4) {
+                        /* Enable an x4 device */
+                        dword |= 0x08 << ((i<<3 ) + 4);
+                }
+		
+	/* go to the next DIMM */
+	}
+
+	/* Write the new row attributes register */
+	pci_write_config32(ctrl->d0, 0x70, dword);
+
+	return dimm_mask;
+
+}
+#if 0
+	/*
+	 * Routine:	sdram_read_paired_byte
+	 * Arguments:	%esp return address
+	 *		%bl device on the smbus to read from
+	 *              %bh address on the smbus to read
+	 * Results:	
+	 *		zf clear
+	 *		byte read in %al
+	 *	On Error:
+	 *		zf set
+	 *		%eax trashed
+	 *
+	 * Preserved:	%ebx, %esi, %edi
+	 *
+	 * Trashed:	%eax, %ecx, %edx, %ebp, %esp, %eflags
+	 * Used:	%eax, %ebx, %ecx, %edx, %esp, %eflags
+	 *
+	 * Effects:	Reads two spd bytes from both ram channesl
+	 *              and errors if they are not equal.
+	 *		It then returns the equal result.
+	 */
+static spd_read_paired_byte () {
+	movl	%esp, %ebp
+	CALLSP(smbus_read_byte)
+	setnz	%cl
+	movb	%al, %ch
+	addb	$(SMBUS_MEM_CHANNEL_OFF), %bl
+	CALLSP(smbus_read_byte)
+	movb	%ch, %ah
+	setnz	%ch
+	subb	$(SMBUS_MEM_CHANNEL_OFF), %bl
+
+	/* See if dimms on both sides are equally present */	
+	cmp	%cl, %ch
+	jne	sdram_presence_mismatch
+
+	/* Leave if I have no data */
+	testb	%cl, %cl
+	jz	spd_verify_byte_out
+
+	/* Verify the data is identical */
+	cmp	%ah, %al
+	jne	sdram_value_mismatch
+
+	/* Clear the zero flag */
+	testb	%cl, %cl
+spd_verify_byte_out:
+	movl	%ebp, %esp
+	RETSP
+}
+
+	/*
+	 * Routine:	spd_verify_dimms
+	 * Arguments:	none
+	 * Results:	none
+	 * Preserved:	none
+	 * Trashed:	%eax, %ebx, %ecx, %edx, %ebp, %esi, %edi, %esp, %eflags
+	 * Used:	%eax, %ebx, %ecx, %edx, %ebp, %esi, %edi, %esp, %eflags
+	 *
+	 * Effects:	
+	 *		- Verify all interesting spd information
+	 *		  matches for both dimm channels.
+	 *		- Additional error checks that can be easily done
+	 *		  here are computed as well, so I don't need to
+	 *		  worry about them later.
+	 */
+static spd_verify_dimms() {
+	movl	$(SMBUS_MEM_DEVICE_START), %ebx
+spd_verify_dimm:
+	/* Verify this is DDR SDRAM */
+	movb	$2, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_verify_next_dimm
+	cmpb	$7, %al
+	jne	invalid_dimm_type
+
+	/* Verify the row addresses */
+	movb	$3, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	$0x0f, %al
+	jz	spd_invalid_data
+	
+	/* Column addresses */
+	movb	$4, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	$0xf, %al
+	jz	spd_invalid_data
+
+	/* Physical Banks */
+	movb	$5, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	cmp	$1, %al
+	jb	spd_invalid_data
+	cmp	$2, %al
+	ja	spd_invalid_data
+
+	/* Module Data Width */
+	movb	$7, %bh
+	CALLSP(spd_read_paired_byte)	
+	jz	spd_missing_data
+	cmpb	$0, %al
+	jne	spd_invalid_data
+
+	movb	$6, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	cmpb	$64, %al
+	je	1f
+	cmpb	$72, %al
+	je	1f
+	jmp	spd_unsupported_data
+1:
+
+	/* Cycle time at highest CAS latency CL=X */
+	movb	$9, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+
+	/* SDRAM type */
+	movb	$11, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+
+	/* Refresh Interval */
+	movb	$12, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	
+	/* SDRAM Width */
+	movb	$13, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	andb	$0x7f, %al
+	cmpb	$4, %al
+	je	1f
+	cmpb	$8, %al
+	je	1f
+	jmp	spd_unsupported_data
+1:
+
+	/* Back-to-Back Random Column Accesses */
+	movb	$15, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	%al, %al
+	jz	spd_invalid_data
+	cmpb	$4, %al
+	ja	spd_unsupported_data
+
+	/* Burst Lengths */
+	movb	$16, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	$(1<<2), %al
+	jz	spd_unsupported_data
+
+	/* Logical Banks */
+	movb	$17, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	%al, %al
+	jz	spd_invalid_data
+	
+	/* Supported CAS Latencies */
+	movb	$18, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	$(1 << 1), %al /* CL 1.5 */
+	jnz	1f
+	testb	$(1 << 2), %al /* CL 2.0 */
+	jnz	1f
+	testb	$(1 << 3), %al /* CL 2.5 */
+	jnz	1f
+	jmp	spd_unsupported_data
+1:
+	
+	/* Cycle time at Cas Latency (CLX - 0.5) */
+	movb	$23, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	
+	/* Cycle time at Cas Latency (CLX - 1.0) */
+	movb	$26, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	
+	/* tRP Row precharge time */
+	movb	$27, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	$0xfc, %al
+	jz	spd_invalid_data
+	
+
+	/* tRCD RAS to CAS */
+	movb	$29, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	$0xfc, %al
+	jz	spd_invalid_data
+	
+	/* tRAS Activate to Precharge */
+	movb	$30, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	%al, %al
+	jz	spd_invalid_data
+
+	/* Module Bank Density */
+	movb	$31, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+	testb	$(1<<2), %al		/* 16MB */
+	jnz	spd_unsupported_data
+	testb	$(1<<3), %al
+	jnz	spd_unsupported_data	/* 32MB */
+	
+	/* Address and Command Hold Time After Clock */
+	movb	$33, %bh
+	CALLSP(spd_read_paired_byte)
+	jz	spd_missing_data
+
+spd_verify_next_dimm:
+	/* go to the next DIMM */
+	addb	$(SMBUS_MEM_DEVICE_INC), %bl /* increment the smbus device */
+	cmpb	$SMBUS_MEM_DEVICE_END, %bl
+	jbe	spd_verify_dimm
+spd_verify_dimms_out:
+	RET_LABEL(spd_verify_dimms)
+}
+#endif
+#define spd_pre_init  "Reading SPD data...\r\n"
+#define spd_pre_set "setting based on SPD data...\r\n"
+#define spd_post_init "done\r\n"
+
+
+static const uint32_t refresh_rate_rank[]= {
+	/* Refresh rates ordered from most conservative (lowest)
+	 * to most agressive (highest)
+	 * disabled 0 -> rank 3 
+	 * 15.6usec 1 -> rank 1
+	 * 7.8 usec 2 -> rank 0
+	 * 64usec   3 -> rank 2
+	 */
+	3, 1, 0, 2 };
+static const uint32_t refresh_rate_index[] = {
+	/* Map the spd refresh rates to memory controller settings 
+	 * 15.625us -> 15.6us
+ 	 * 3.9us    -> err
+	 * 7.8us    -> 7.8us
+	 * 31.3s    -> 15.6us
+	 * 62.5us   -> 15.6us
+	 * 125us    -> 64us
+	 */
+	1, 0xff, 2, 1, 1, 3
+};
+#define MAX_SPD_REFRESH_RATE 5
+
+static long spd_set_dram_controller_mode (const struct mem_controller *ctrl, long dimm_mask) {
+
+        int i;  
+        uint32_t dword;
+        int value;
+	uint32_t ecx;
+	uint32_t edx;
+        
+        /* Read the inititial state */
+        dword = pci_read_config32(ctrl->d0, 0x7c);
+
+#if 0
+        /* Test if ECC cmos option is enabled */
+        movb    $RTC_BOOT_BYTE, %al
+        outb    %al, $0x70
+        inb     $0x71, %al
+        testb   $(1<<2), %al
+        jnz     1f
+        /* Clear the ecc enable */
+        andl    $~(3 << 20), %esi
+1:
+#endif
+
+
+        /* Walk through all dimms and find the interesection of the support
+         * for ecc sdram and refresh rates
+         */        
+
+ 
+        for(i = 0; i < DIMM_SOCKETS; i++) {
+		if (!(dimm_mask & (1 << i))) {
+                        continue;
+                }
+		 /* Test to see if I have ecc sdram */
+                value = spd_read_byte(ctrl->channel0[i], 11);  /* SDRAM type */
+                if(value < 0) continue;
+		if(value !=2 ) {
+			/* Clear the ecc enable */
+			dword &= ~(3 << 20);
+		}
+		value = spd_read_byte(ctrl->channel0[i], 12);  /* SDRAM refresh rate */
+		if(value < 0 ) continue;
+		value &= 0x7f;
+		if(value > MAX_SPD_REFRESH_RATE) { print_err("unsupported refresh rate\r\n");}
+//		if(value == 0xff) { print_err("unsupported refresh rate\r\n");}
+		
+		ecx = refresh_rate_index[value];
+
+		/* Isolate the old refresh rate setting */
+		/* Load the refresh rate ranks */
+		edx = refresh_rate_rank[(dword >> 8) & 3]<<8;
+		edx |= refresh_rate_rank[ecx] & 0xff; 
+	
+		/* See if the new refresh rate is more conservative than the old
+	 	* refresh rate setting. (Lower ranks are more conservative)
+	 	*/
+		if((edx & 0xff)< ((edx >> 8) & 0xff) ) {
+			/* Clear the old refresh rate */
+			dword &= ~(3<<8);
+			/* Move in the new refresh rate */
+			dword |= (ecx<<8);
+		}
+		
+		value = spd_read_byte(ctrl->channel0[i], 33); /* Address and command hold time after clock */
+		if(value < 0) continue;
+		if(value >= 0xa0) { 		/* At 133Mhz this constant should be 0x75 */
+			dword &= ~(1<<16);	/* Use two clock cyles instead of one */
+		}
+	
+	/* go to the next DIMM */
+	}
+
+	/* Now write the controller mode */
+	pci_write_config32(ctrl->d0, 0x7c, dword);
+	
+	return dimm_mask;
+
+}
+static long spd_enable_clocks(const struct mem_controller *ctrl, long dimm_mask)
+{
+        int i;
+	uint32_t dword;
+	int value;
+
+        /* Read the inititial state */
+        dword = pci_read_config32(ctrl->d0, 0x8c);
+#if 0
+# Intel clears top bit here, should we?
+# No the default is on and for normal timming it should be on.  Tom Z
+        andl    $0x7f, %esi
+#endif
+
+ 
+        for(i = 0; i < DIMM_SOCKETS; i++) {
+		if (!(dimm_mask & (1 << i))) {
+                        continue;
+                }
+	        /* Read any spd byte to see if the dimm is present */
+	        value = spd_read_byte(ctrl->channel0[i], 5); /* Physical Banks */
+       	 	if(value < 0) continue;
+        
+        	dword &= ~(1<<i);
+        }
+	
+	pci_write_config32(ctrl->d0, 0x8c, dword);
+	
+	return dimm_mask;
+}
+
+static const uint16_t cas_latency_80[] = {
+	/* For cas latency 2.0 0x01 works and until I see a large test sample
+	 * I am not prepared to change this value, to the intel recommended value
+	 * of 0x0d.  Eric Biederman
+ 	 */
+ 	/* The E7501 requires b1 rather than 01 for CAS2 or memory will be hosed
+ 	 * CAS 1.5 is claimed to be unsupported, will try to test that
+ 	 * will need to determine correct values for other CAS values
+ 	 * (perhaps b5, b1, b6?)
+ 	 * Steven James 02/06/2003
+ 	 */
+ 	 
+//#	.byte 0x05, 0x01, 0x06 
+//#	.byte 0xb5, 0xb1, 0xb6 
+	0x0, 0x0bb1, 0x0662   /* RCVEN */ 
+};
+static const uint16_t cas_latency_80_4dimms[] = {
+        0x0, 0x0bb1, 0x0882
+};
+
+
+static const uint8_t cas_latency_78[] = {
+	DRT_CAS_1_5, DRT_CAS_2_0, DRT_CAS_2_5
+};
+
+static long spd_set_cas_latency(const struct mem_controller *ctrl, long dimm_mask) {
+	/* Walk through all dimms and find the interesection of the
+	 * supported cas latencies.
+	 */
+        int i;
+        /* Initially allow cas latencies 2.5, 2.0
+         * which the chipset supports.
+         */
+	uint32_t dword = (1<<3)| (1<<2);// esi
+	uint32_t edi;
+	uint32_t ecx;
+	unsigned device;
+	int value;
+	uint8_t byte;
+	uint16_t word;
+
+	
+        for(i = 0; i < DIMM_SOCKETS; i++) {
+		if (!(dimm_mask & (1 << i))) {
+                        continue;
+                }
+		value = spd_read_byte(ctrl->channel0[i], 18);
+		if(value < 0) continue;
+		/* Find the highest supported cas latency */
+		ecx = log2(value & 0xff); 
+		edi = (1<< ecx);
+
+		 /* Remember the supported cas latencies */
+        	ecx = (value & 0xff);
+
+		/* Verify each cas latency at 133Mhz */
+		/* Verify slowest/highest CAS latency */
+		value = spd_read_byte(ctrl->channel0[i], 9);
+		if(value < 0 ) continue;
+		if(value > 0x75 ) {	
+			/* The bus is too fast so we cannot support this case latency */
+			ecx &= ~edi;
+		}
+
+		/* Verify the highest CAS latency - 0.5 clocks */
+		edi >>= 1;
+		if(edi != 0) {
+			value = spd_read_byte(ctrl->channel0[i], 23);
+			if(value < 0 ) continue;
+			if(value > 0x75) {
+				/* The bus is too fast so we cannot support this cas latency */
+				ecx &= ~edi;
+			}
+		}
+
+		/* Verify the highest CAS latency - 1.0 clocks */
+		edi >>=1;
+		if(edi !=0) {
+                        value = spd_read_byte(ctrl->channel0[i], 25);
+                        if(value < 0 ) continue;
+                        if(value > 0x75) {
+                                /* The bus is too fast so we cannot support this cas latency */
+                                ecx &= ~edi;
+                        }
+		}
+
+		/* Now find which cas latencies are supported for the bus */
+		dword &= ecx;
+	/* go to the next DIMM */
+	}
+
+	/* After all of the arduous calculation setup with the fastest
+	 * cas latency I can use.
+	 */
+	value = __builtin_bsf(dword);  // bsrl = log2 how about bsfl?
+	if(value ==0 ) return -1;
+	ecx = value -1;
+
+	byte = pci_read_config8(ctrl->d0, 0x78);
+	byte &= ~(DRT_CAS_MASK);
+	byte |= cas_latency_78[ecx];
+	pci_write_config8(ctrl->d0,0x78, byte);
+
+	/* set master DLL reset */
+	dword = pci_read_config32(ctrl->d0, 0x88);
+	dword |= (1<<26);
+	
+	/* the rest of the references are words */
+//	ecx<<=1;  // don't need shift left, because we already define that in u16 array
+	pci_write_config32(ctrl->d0, 0x88, dword);
+	
+	
+	dword &= 0x0c0000ff;	/* patch try register 88 is undocumented tnz */
+	dword |= 0xd2109800;
+
+	pci_write_config32(ctrl->d0, 0x88, dword);
+	
+	word = pci_read_config16(ctrl->d0, 0x80);
+	word &= ~(0x0fff);
+	word |= cas_latency_80[ecx];
+
+	dword = pci_read_config32(ctrl->d0, 0x70);
+
+	if((dword & 0xff) !=0 ) {
+		dword >>=8;
+		if((dword & 0xff)!=0) {
+			dword >>=8;
+			if((dword & 0xff)!=0) {
+				dword >>= 8;
+				if( (dword & 0xff)!=0) {
+        				word &=~(0x0fff);  /* we have dimms in all 4 slots */ 
+        				word |=cas_latency_80_4dimms[ecx];
+				}
+			}
+		}
+	}
+	
+	pci_write_config16(ctrl->d0, 0x80, word);
+	
+	dword = pci_read_config32(ctrl->d0, 0x88);	/* reset master DLL reset */
+	dword &= ~(1<<26);
+	pci_write_config32(ctrl->d0, 0x88, dword);
+	
+	RAM_RESET_DDR_PTR(ctrl);
+
+	return dimm_mask;
+
+}
+
+static long spd_set_dram_timing(const struct mem_controller *ctrl, long dimm_mask) {
+	/* Walk through all dimms and find the interesection of the
+	 * supported dram timings.
+	 */
+
+        int i;
+        uint32_t dword;
+        int value;
+
+        /* Read the inititial state */
+        dword = pci_read_config32(ctrl->d0, 0x78);
+#if 0
+# Intel clears top bit here, should we?
+# No the default is on and for normal timming it should be on.  Tom Z
+        andl    $0x7f, %esi
+#endif
+        
+        
+        for(i = 0; i < DIMM_SOCKETS; i++) {
+		if (!(dimm_mask & (1 << i))) {
+                        continue;
+                }
+		/* Trp */
+                value = spd_read_byte(ctrl->channel0[i], 27);
+                if(value < 0) continue;
+		if(value > (15<<2)) {
+        		/* At 133Mhz if row precharge time is above than 15ns than we
+         		 * need 3 clocks not 2 clocks.
+         		*/
+			dword &= ~(1<<0); 
+		}
+		/*  Trcd */
+		value = spd_read_byte(ctrl->channel0[i],29);
+		if(value < 0 ) continue;
+		if(value > (15<<2)) {
+		        /* At 133Mhz if the Minimum ras to cas delay is about 15ns we
+        		 * need 3 clocks not 2 clocks.
+         		*/
+			dword &= ~((1<<3)|(1<<1));
+		}
+		/* Tras */
+		value = spd_read_byte(ctrl->channel0[i],30);
+		if(value < 0 ) continue;
+		        /* Convert tRAS from ns to 133Mhz clock cycles */
+		value <<=1;	 /* mult by 2 to make 7.5 15 */
+		value  += 15;	/* Make certain we round up */
+		value --;
+		value &= 0xff;	/* Clear the upper bits of eax */
+		value /= 15;
+		
+		/* Don't even process small timings */
+		if(value >5) {
+			uint32_t tmp;
+			/* Die if the value is to large */
+			if(value>7) {
+				die ("unsupported_rcd\r\n");
+			}
+			/* Convert to clocks - 5 */
+			value -=5;
+			/* Convert the existing value into clocks - 5 */
+			tmp = (~((dword>>9) & 3) - 1) & 3;
+			/* See if we need a slower timing */
+			if(value > tmp ) {
+				/* O.k. put in our slower timing */
+				dword &= ~(3<<9);
+				dword |= ((~(value + 1)) & 3)<<9 ;
+			}
+		}
+	
+		/* Trd */ 
+		/* Set to a 7 clock read delay. This is for 133Mhz
+	 	*  with a CAS latency of 2.5  if 2.0 a 6 clock
+	 	*  delay is good  */
+		if( (pci_read_config8(ctrl->d0, 0x78) & 0x30) ==0 ){
+			dword &= ~(7<<24); /* CAS latency is 2.5, make 7 clks */
+		}
+
+		/*
+	 	* Back to Back Read Turn Around
+	 	*/
+		/* Set to a 3 clock back to back read turn around.  This
+	 	 *  is good for CAS latencys 2.5 and 2.0 */
+		dword |= (1<<27);
+		/*
+	 	* Back to Back Read-Write Turn Around
+	 	*/
+		/* Set to a 5 clock back to back read to write turn around.
+	 	*  4 is a good delay if the CAS latency is 2.0 */
+		if( ( pci_read_config8(ctrl->d0, 0x78) & (1<<4)) == 0) {
+			dword &= ~(1<<28);
+		}
+		/*
+	 	* Back to Back Write-Read Turn Around
+	 	*/
+		/* Set to a 2 clock back to back write to read turn around.
+	 	*  This is good for 2.5 and 2.0 CAS Latencies. */
+		dword |= (1<<29);
+	}
+	
+	pci_write_config32(ctrl->d0, 0x78, dword);
+	
+	return dimm_mask;
+
+}
+static unsigned int spd_detect_dimms(const struct mem_controller *ctrl)
+{               
+        unsigned dimm_mask;
+        int i;  
+        dimm_mask = 0;  
+#if DEBUG_RAM_CONFIG
+	print_debug("spd_detect_dimms:\r\n");
+#endif
+        for(i = 0; i < DIMM_SOCKETS; i++) {
+                int byte;
+                unsigned device;
+#if DEBUG_RAM_CONFIG
+		print_debug_hex32(i);
+		print_debug("\r\n");
+#endif
+                device = ctrl->channel0[i];
+                if (device) {
+                        byte = spd_read_byte(ctrl->channel0[i], 2);  /* Type */
+                        if (byte == 7) {
+                                dimm_mask |= (1 << i);
+                        }
+                }
+#if 1
+                device = ctrl->channel1[i];
+                if (device) {
+                        byte = spd_read_byte(ctrl->channel1[i], 2);
+                        if (byte == 7) {
+                                dimm_mask |= (1 << (i + DIMM_SOCKETS));
+                        }
+                }
+#endif
+        }       
+#if 1
+	i = (dimm_mask>>DIMM_SOCKETS);
+	if(i != (dimm_mask & ( (1<<DIMM_SOCKETS) - 1) ) ) {
+		die("now we only support dual channel\r\n");
+	}
+
+#endif
+
+        return dimm_mask;
+}               
+
+static uint32_t set_dimm_size(const struct mem_controller *ctrl, struct dimm_size sz, uint32_t memsz, unsigned index)
+{
+        int i;
+        uint32_t base0, base1;
+        uint32_t dch;
+	uint8_t byte;
+
+        /* Double the size if we are using dual channel memory */
+//        if (is_dual_channel(ctrl)) {
+                /* Since I have 2 identical channels double the sizes */
+                sz.side1++ ;
+                sz.side2++;
+//        }
+              
+	if (sz.side1 != sz.side2) {
+                sz.side2 = 0;
+        } 
+ 
+        /* Make certain side1 of the dimm is at least 64MB */
+        if (sz.side1 >= (25 + 4)) {
+                memsz += (1 << (sz.side1 - (25 + 4)) ) ;
+        }
+	 /* Write the size of side 1 of the dimm */
+	byte = memsz;
+        pci_write_config8(ctrl->d0, 0x60+(index<<1), byte);
+
+        /* Make certain side2 of the dimm is at least 64MB */
+        if (sz.side2 >= (25 + 4)) {
+                memsz += (1 << (sz.side2 - (25 + 4)) ) ;
+        }
+        
+         /* Write the size of side 2 of the dimm */
+	byte = memsz;
+        pci_write_config8(ctrl->d0, 0x61+(index<<1), byte);
+        
+        /* now, fill in DRBs where no physical slot exists */
+        
+        for(i=index+1;i<4;i++) {
+                pci_write_config8(ctrl->d0, 0x60+(i<<1),byte);
+                pci_write_config8(ctrl->d0, 0x61+(i<<1),byte);
+        
+        }
+        
+        return memsz;
+
+}
+/* LAST_DRB_SLOT is a constant for any E7500 board */
+#define LAST_DRB_SLOT 0x67
+
+static long spd_set_ram_size(const struct mem_controller *ctrl, long dimm_mask)
+{
+        int i;
+        uint32_t memsz=0;
+	uint16_t word;
+
+        for(i = 0; i < DIMM_SOCKETS; i++) {
+                struct dimm_size sz;
+                if (!(dimm_mask & (1 << i))) {
+                        continue;
+                }
+                sz = spd_get_dimm_size(ctrl->channel0[i]);
+#if DEBUG_RAM_CONFIG
+                print_debug("dimm size =");
+                print_debug_hex32(sz.side1);
+                print_debug(" ");
+                print_debug_hex32(sz.side2);
+                print_debug("\r\n");
+#endif
+
+                if (sz.side1 == 0) {
+			return -1; /* Report SPD error */
+                }
+                memsz = set_dimm_size(ctrl, sz, memsz, i);
+        }
+        /* For now hardset everything at 128MB boundaries */
+        /* %ebp has the ram size in multiples of 64MB */
+//        cmpl    $0, %ebp        /* test if there is no mem - smbus went bad */
+//        jz      no_memory_bad_smbus
+        if(memsz < 0x30)  {
+        	/* I should really adjust all of this in C after I have resources
+         	* to all of the pcie devices.
+         	*/
+
+        	/* Round up to 128M granularity */
+        	memsz++;
+        	memsz &= 0xfe;
+        	memsz<<= 10;
+		word = memsz;
+        	pci_write_config16(ctrl->d0, 0xc4, word);
+        } else {
+
+        	/* FIXME will this work with 3.5G of ram? */
+        	/* Put TOLM at 3G */
+        	pci_write_config16(ctrl->d0, 0xc4, 0xc000);
+        	/* Hard code a 1G remap window, right after the ram */
+        	if(memsz< 0x40){
+                	word = 0x40;  /* Ensure we are over 4G */
+        	} else {
+			word = memsz;
+		}
+        	pci_write_config16(ctrl->d0, 0xc6, word);
+		word += 0x10;
+        	pci_write_config16(ctrl->d0, 0xc8, word);
+
+        }
+
+        return dimm_mask;
+}
+                                                
+static void sdram_set_spd_registers(const struct mem_controller *ctrl) {
+	long dimm_mask;
+#if DEBUG_RAM_CONFIG
+	print_debug(spd_pre_init);
+#endif
+        //activate_spd_rom(ctrl);
+        dimm_mask = spd_detect_dimms(ctrl);
+	if (!(dimm_mask & ((1 << DIMM_SOCKETS) - 1))) {
+                print_debug("No memory for this controller\n");
+                return;
+        }
+	dimm_mask = spd_enable_clocks(ctrl, dimm_mask);
+        if (dimm_mask < 0)
+                goto hw_spd_err;
+	//spd_verify_dimms(ctrl);
+#if DEBUG_RAM_CONFIG
+	print_debug(spd_pre_set);
+#endif
+	dimm_mask = spd_set_row_attributes(ctrl,dimm_mask);
+        if (dimm_mask < 0)
+                goto hw_spd_err;
+	dimm_mask = spd_set_dram_controller_mode(ctrl,dimm_mask);
+        if (dimm_mask < 0)
+                goto hw_spd_err;	
+	dimm_mask = spd_set_cas_latency(ctrl,dimm_mask);
+        if (dimm_mask < 0)
+                goto hw_spd_err;
+	dimm_mask = spd_set_dram_timing(ctrl,dimm_mask);
+        if (dimm_mask < 0)
+                goto hw_spd_err;
+#if DEBUG_RAM_CONFIG
+	print_debug(spd_post_init);
+#endif
+	//moved from dram_post_init
+	spd_set_ram_size(ctrl, dimm_mask);
+	        return;
+ hw_spd_err:
+        /* Unrecoverable error reading SPD data */
+        print_err("SPD error - reset\r\n");
+        hard_reset();
+        return;
+}
+
+
+	/* I have finally seen ram bad enough to cause LinuxBIOS
+	 * to die in mysterious ways, before booting up far
+	 * enough to run a memory tester.  This code attempts
+	 * to catch this blatantly bad ram, with a spot check.
+	 * For most cases you should boot all of the way up 
+	 * and run a memory tester.  
+	 */
+	/* Ensure I read/write each stick of bank of memory &&
+	 * that I do more than 1000 bytes to avoid the northbridge cache.
+	 * Only 64M of each side of each DIMM is currently mapped,
+	 * so we can handle > 4GB of ram here.
+	 */
+#if 0
+#define bank_msg  "Bank "
+#define side_msg " Side "
+static void verify_ram() {
+	xorl	%ecx, %ecx
+	/* Check to see if the RAM is present,
+	 * in the specified bank and side.
+	 */
+1:	movl	%ecx, %ebx
+	shrl	$1, %ebx
+	addl	$((5<<8) | SMBUS_MEM_DEVICE_START), %ebx
+	CALLSP(smbus_read_byte)
+	jz	5f
+	testl	$1, %ecx
+	jz	2f
+	cmpb	$2, %al
+	jne	5f
+
+	/* Display the bank and side we are spot checking.
+	 */
+2:	CONSOLE_INFO_TX_STRING($bank_msg)
+	movl	%ecx, %ebx
+	shrl	$1, %ebx
+	incl	%ebx
+	CONSOLE_INFO_TX_HEX8(%bl)
+	CONSOLE_INFO_TX_STRING($side_msg)
+	movl	%ecx, %ebx
+	andl	$1, %ebx
+	CONSOLE_INFO_TX_HEX8(%bl)
+
+	/* Compute the memory address to spot check. */
+	movl	%ecx, %ebx
+	xorl	%eax, %eax
+3:	testl	%ebx, %ebx
+	jz	4f
+	addl	$0x04000000, %eax
+	decl	%ebx
+	jmp	3b
+4:
+	/* Spot check 512K of RAM */
+	movl	%eax, %ebx
+	addl	$0x0007ffff, %ebx
+	CALLSP(spot_check)
+5:	
+	/* Now find the next bank and side to spot check */
+	incl	%ecx
+	cmpl	$((SMBUS_MEM_DEVICE_END - SMBUS_MEM_DEVICE_START)<<1), %ecx
+	jb	1b
+	RET_LABEL(verify_ram)
+
+}
+#endif	
+
+#if 0
+static void ram_postinit(const struct mem_controller *ctrl) {
+#if DEBUG_RAM_CONFIG 
+	dumpnorth();
+#endif
+	/* Include a test to verify that memory is more or less working o.k. 
+  	 * This test is to catch programming errors and hardware that is out of
+	 * spec, not a test to see if the memory dimms are working 100%
+	 */
+//#	CALL_LABEL(verify_ram)
+	spd_set_ram_size(ctrl);
+}
+#define FIRST_NORMAL_REFERENCE() CALL_LABEL(ram_postinit)
+
+#define SPECIAL_FINISHUP()   CALL_LABEL(dram_finish)
+
+#endif
+
+#define ecc_pre_init	"Initializing ECC state...\r\n"
+#define ecc_post_init	"ECC state initialized.\r\n"
+static void dram_finish(const struct mem_controller *ctrl)
+{
+	uint32_t dword;
+	uint8_t byte;
+	/* Test to see if ECC support is enabled */
+	dword = pci_read_config32(ctrl->d0, 0x7c);
+	dword >>=20;
+	dword &=3;
+	if(dword == 2)  {
+		
+#if DEBUG_RAM_CONFIG	
+		print_debug(ecc_pre_init);
+#endif
+		/* Initialize ECC bits , use ECC zero mode (new to 7501)*/
+		pci_write_config8(ctrl->d0, 0x52, 0x06);
+		pci_write_config8(ctrl->d0, 0x52, 0x07);
+		do {
+			byte = pci_read_config8(ctrl->d0, 0x52);
+
+		} while ( (byte & 0x08 ) == 0);
+
+		pci_write_config8(ctrl->d0, 0x52, byte & 0xfc);
+#if DEBUG_RAM_CONFIG		
+		print_debug(ecc_post_init);	
+#endif
+
+		/* Clear the ECC error bits */
+		pci_write_config8(ctrl->d0f1, 0x80, 0x03); /* dev 0, function 1, offset 80 */
+		pci_write_config8(ctrl->d0f1, 0x82, 0x03); /* dev 0, function 1, offset 82 */
+
+		pci_write_config32(ctrl->d0f1, 0x40, 1<<18); /* clear dev 0, function 1, offset 40; bit 18 by writing a 1 to it */
+  	        pci_write_config32(ctrl->d0f1, 0x44, 1<<18); /* clear dev 0, function 1, offset 44; bit 18 by writing a 1 to it */
+
+		pci_write_config8(ctrl->d0, 0x52, 0x0d);
+	}
+	
+	dword = pci_read_config32(ctrl->d0, 0x7c); /* FCS_EN */
+	dword |= (1<<17);
+	pci_write_config32(ctrl->d0, 0x7c, dword);
+
+
+#if DEBUG_RAM_CONFIG 
+	dumpnorth();
+#endif
+
+//	verify_ram();
+}
+#if 0
+#define ERRFUNC(x, str) mem_err(x, str)
+
+
+ERRFUNC(invalid_dimm_type,          "Invalid dimm type")
+ERRFUNC(spd_missing_data,           "Missing sdram spd data")
+ERRFUNC(spd_invalid_data,           "Invalid sdram spd data")
+ERRFUNC(spd_unsupported_data,       "Unsupported sdram spd value")
+ERRFUNC(unsupported_page_size,      "Unsupported page size")
+ERRFUNC(sdram_presence_mismatch,    "DIMM presence mismatch")
+ERRFUNC(sdram_value_mismatch,       "spd data does not match")
+ERRFUNC(unsupported_refresh_rate,   "Unsuported spd refresh rate")
+ERRFUNC(inconsistent_cas_latencies, "No cas latency supported by all dimms")
+ERRFUNC(unsupported_rcd,            "Unsupported ras to cas delay")
+#undef ERRFUNC
+
+#define mem_err_err "ERROR: "
+#define mem_err_pair " on dimm pair "
+#define mem_err_byte " spd byte "
+static void mem_err {
+	movl	%ebx, %edi
+	CONSOLE_ERR_TX_STRING($mem_err_err)
+	CONSOLE_ERR_TX_STRING(%esi)
+	CONSOLE_ERR_TX_STRING($mem_err_pair)
+	movl	%edi, %ebx
+	subb	$(SMBUS_MEM_DEVICE_START), %bl
+	CONSOLE_ERR_TX_HEX8(%bl)
+	CONSOLE_ERR_TX_STRING($mem_err_byte)
+	movl	%edi, %ebx
+	CONSOLE_ERR_TX_HEX8(%bh)
+	jmp	mem_stop
+
+}
+
+#endif
+
+
+#if ASM_CONSOLE_LOGLEVEL > BIOS_DEBUG
+#define ram_enable_1    "Ram Enable 1\r\n"
+#define ram_enable_2	"Ram Enable 2\r\n"
+#define ram_enable_3 	"Ram Enable 3\r\n"
+#define ram_enable_4 	"Ram Enable 4\r\n"
+#define ram_enable_5 	"Ram Enable 5\r\n"
+#define ram_enable_6 	"Ram Enable 6\r\n"
+#define ram_enable_7 	"Ram Enable 7\r\n"
+#define ram_enable_8 	"Ram Enable 8\r\n"
+#define ram_enable_9 	"Ram Enable 9\r\n"
+#define ram_enable_10 	"Ram Enable 10\r\n"
+#define ram_enable_11 	"Ram Enable 11\r\n"
+#endif
+
+	/* Estimate that SLOW_DOWN_IO takes about 50&76us*/
+	/* delay for 200us */
+
+#define DO_DELAY \
+	udelay(200);
+//	for(i=0; i<16;i++)  { 	SLOW_DOWN_IO	}
+		
+
+#define EXTRA_DELAY DO_DELAY
+
+static void sdram_enable(int controllers, const struct mem_controller *ctrl)
+{
+	int i;
+	/* 1 & 2 Power up and start clocks */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_1);
+	print_debug(ram_enable_2);
+#endif
+
+	/* A 200us delay is needed */
+
+	DO_DELAY
+	EXTRA_DELAY
+
+	/* 3. Apply NOP */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_3);
+#endif
+	RAM_NOP(ctrl);
+	EXTRA_DELAY
+
+	/* 4 Precharge all */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_4);
+#endif
+	RAM_PRECHARGE(ctrl);
+	EXTRA_DELAY
+	
+	/* wait until the all banks idle state... */
+	/* 5. Issue EMRS to enable DLL */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_5);
+#endif
+	RAM_EMRS(ctrl);
+	EXTRA_DELAY
+	
+	/* 6. Reset DLL */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_6);
+#endif
+	RAM_MRS(ctrl,1);
+	EXTRA_DELAY
+
+	/* Ensure a 200us delay between the DLL reset in step 6 and the final
+	 * mode register set in step 9.
+	 * Infineon needs this before any other command is sent to the ram.
+	 */
+	DO_DELAY
+	EXTRA_DELAY
+	
+	/* 7 Precharge all */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_7);
+#endif
+	RAM_PRECHARGE(ctrl);
+	EXTRA_DELAY
+	
+	/* 8 Now we need 2 AUTO REFRESH / CBR cycles to be performed */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_8);
+#endif
+	RAM_CBR(ctrl);
+	EXTRA_DELAY
+	RAM_CBR(ctrl);
+	EXTRA_DELAY
+	/* And for good luck 6 more CBRs */
+	RAM_CBR(ctrl);
+	EXTRA_DELAY
+	RAM_CBR(ctrl);
+	EXTRA_DELAY
+	RAM_CBR(ctrl);
+	EXTRA_DELAY
+	RAM_CBR(ctrl);
+	EXTRA_DELAY
+	RAM_CBR(ctrl);
+	EXTRA_DELAY
+	RAM_CBR(ctrl);
+	EXTRA_DELAY
+
+	/* 9 mode register set */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_9);
+#endif
+	RAM_MRS(ctrl,0);
+	EXTRA_DELAY
+	
+	/* 10 DDR Receive FIFO RE-Sync */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_10);
+#endif
+	RAM_RESET_DDR_PTR(ctrl);
+	EXTRA_DELAY
+	
+	/* 11 normal operation */
+#if DEBUG_RAM_CONFIG 
+	print_debug(ram_enable_11);
+#endif
+	RAM_NORMAL(ctrl);
+
+
+	// special from v1
+        //FIRST_NORMAL_REFERENCE();
+	//spd_set_ram_size(ctrl, 0x03);
+
+        /* Finally enable refresh */
+        ENABLE_REFRESH(ctrl);
+
+	//SPECIAL_FINISHUP();
+	dram_finish(ctrl);
+
+}
+
diff --git a/src/northbridge/intel/e7501/raminit.h b/src/northbridge/intel/e7501/raminit.h
new file mode 100644
index 0000000000..c1dc4baeaf
--- /dev/null
+++ b/src/northbridge/intel/e7501/raminit.h
@@ -0,0 +1,12 @@
+#ifndef RAMINIT_H
+#define RAMINIT_H
+
+#define DIMM_SOCKETS 4
+struct mem_controller {
+	device_t d0, d0f1; 
+	uint16_t channel0[DIMM_SOCKETS];
+	uint16_t channel1[DIMM_SOCKETS];
+};
+
+
+#endif /* RAMINIT_H */
diff --git a/src/northbridge/intel/e7501/reset_test.c b/src/northbridge/intel/e7501/reset_test.c
new file mode 100644
index 0000000000..79a5cdaee1
--- /dev/null
+++ b/src/northbridge/intel/e7501/reset_test.c
@@ -0,0 +1,18 @@
+/* Convert to C by yhlu */
+#define MCH_DRC 0x7c
+#define DRC_DONE (1 << 29)
+	/* If I have already booted once skip a bunch of initialization */
+	/* To see if I have already booted I check to see if memory
+	 * has been enabled.
+	 */
+static int bios_reset_detected(void) {
+	uint32_t dword;
+	
+	dword = pci_read_config32(PCI_DEV(0, 0, 0), MCH_DRC);
+	
+	if( (dword & DRC_DONE) != 0 ) {
+		return 1;
+	} 
+	
+	return 0;
+}
diff --git a/src/southbridge/intel/i82801er/Config.lb b/src/southbridge/intel/i82801er/Config.lb
new file mode 100644
index 0000000000..cc77c755a7
--- /dev/null
+++ b/src/southbridge/intel/i82801er/Config.lb
@@ -0,0 +1,11 @@
+config i82801er.h
+driver i82801er.o
+driver i82801er_usb.o
+driver i82801er_lpc.o
+driver i82801er_ide.o
+driver i82801er_sata.o
+driver i82801er_usb2.o
+driver i82801er_ac97.o
+#driver i82801er_nic.o
+#driver i82801er_pci.o
+object i82801er_reset.o
diff --git a/src/southbridge/intel/i82801er/cmos_failover.c b/src/southbridge/intel/i82801er/cmos_failover.c
new file mode 100644
index 0000000000..9702313f9c
--- /dev/null
+++ b/src/southbridge/intel/i82801er/cmos_failover.c
@@ -0,0 +1,16 @@
+//kind of cmos_err for ich5
+#define RTC_FAILED    (1 <<2)
+#define GEN_PMCON_3     0xa4
+static void check_cmos_failed(void) 
+{
+
+                uint8_t byte;
+                byte = pci_read_config8(PCI_DEV(0,0x1f,0),GEN_PMCON_3);
+                if( byte & RTC_FAILED){
+//clear bit 1 and bit 2
+                        byte = cmos_read(RTC_BOOT_BYTE);
+                        byte &= 0x0c;
+                        byte |= MAX_REBOOT_CNT << 4;
+                        cmos_write(byte, RTC_BOOT_BYTE);
+                }
+}
diff --git a/src/southbridge/intel/i82801er/i82801er.c b/src/southbridge/intel/i82801er/i82801er.c
new file mode 100644
index 0000000000..565d672260
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er.c
@@ -0,0 +1,57 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/chip.h>
+#include "i82801er.h"
+
+void i82801er_enable(device_t dev)
+{
+	device_t lpc_dev;
+	unsigned int index;
+	uint16_t reg_old, reg;
+
+//	all 82801er device ares in bus 0
+	unsigned int devfn;
+	devfn = PCI_DEVFN(0x1f, 0); // lpc
+	lpc_dev = dev_find_slot(0, devfn); // 0
+	if (!lpc_dev ) {
+		return;
+	}
+#if 0
+	if ((lpc_dev->vendor != PCI_VENDOR_ID_INTEL) ||
+	    (lpc_dev->device != PCI_DEVICE_ID_INTEL_82801ER_1F0)) {
+		uint32_t id;
+		id = pci_read_config32(lpc_dev, PCI_VENDOR_ID);
+		if (id != (PCI_VENDOR_ID_INTEL | (PCI_DEVICE_ID_INTEL_82801ER_1F0 << 16))) {
+			return;
+		}
+	}
+#endif
+
+	index = (dev->path.u.pci.devfn & 7);
+        if((dev->path.u.pci.devfn & ~0x7)==devfn) { // D=0x1f
+                if(index==0){   //1f0   
+                        index = 14;
+                } 
+        } else { // D=0x1d
+                index += 8;
+        }
+
+	reg_old = pci_read_config16(lpc_dev, FUNC_DIS);
+	reg = reg_old;
+	reg &= ~(1<<index); // enable it
+	if (!dev->enabled) {
+		reg |= (1<<index);  // disable it
+	}
+	if (reg != reg_old) {
+		pci_write_config16(lpc_dev, FUNC_DIS, reg);
+	}
+	reg = pci_read_config16(lpc_dev, FUNC_DIS);
+
+}
+
+struct chip_control southbridge_intel_i82801er_control = {
+	.name       = "Intel 82801er Southbridge",
+	.enable_dev = i82801er_enable,
+};
diff --git a/src/southbridge/intel/i82801er/i82801er.h b/src/southbridge/intel/i82801er/i82801er.h
new file mode 100644
index 0000000000..85dce4ecb7
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er.h
@@ -0,0 +1,81 @@
+#ifndef I82801ER_H
+#define I82801ER_H
+
+struct southbridge_intel_i82801er_config 
+{
+};
+struct chip_control;
+extern struct chip_control southbridge_intel_i82801er_control;
+
+extern void i82801er_enable(device_t dev);
+
+/*
+000 = Non-combined. P0 is primary master. P1 is secondary master.
+001 = Non-combined. P0 is secondary master. P1 is primary master.
+100 = Combined. P0 is primary master. P1 is primary slave. IDE is secondary; Primary IDE channel
+disabled.
+101 = Combined. P0 is primary slave. P1 is primary master. IDE is secondary.
+110 = Combined. IDE is primary. P0 is secondary master. P1 is secondary slave; Secondary IDE
+channel disabled.
+111 = Combined. IDE is primary. P0 is secondary slave. P1 is secondary master.
+*/
+
+#define ICH5_SATA_ADDRESS_MAP 0
+
+
+#define PCI_DMA_CFG     0x90
+#define SERIRQ_CNTL     0x64
+#define GEN_CNTL        0xd0
+#define GEN_STS         0xd4
+#define RTC_CONF        0xd8
+#define GEN_PMCON_3     0xa4
+
+#define PCICMD          0x04
+#define PMBASE          0x40
+#define ACPI_CNTL       0x44
+#define BIOS_CNTL       0x4E
+#define GPIO_BASE       0x58
+#define GPIO_CNTL       0x5C
+#define PIRQA_ROUT      0x60
+#define PIRQE_ROUT      0x68
+#define COM_DEC         0xE0
+#define LPC_EN          0xE6
+#define FUNC_DIS        0xF2
+
+/* 1e f0 244e */
+
+#define CMD             0x04
+#define SBUS_NUM        0x19
+#define SUB_BUS_NUM     0x1A
+#define SMLT            0x1B
+#define IOBASE          0x1C
+#define IOLIM           0x1D
+#define MEMBASE         0x20
+#define MEMLIM          0x22
+#define CNF             0x50
+#define MTT             0x70
+#define PCI_MAST_STS    0x82
+
+#define RTC_FAILED      (1 <<2)
+
+
+#define SMBUS_IO_BASE 0x1000
+
+#define SMBHSTSTAT 0x0
+#define SMBHSTCTL  0x2
+#define SMBHSTCMD  0x3
+#define SMBXMITADD 0x4
+#define SMBHSTDAT0 0x5
+#define SMBHSTDAT1 0x6
+#define SMBBLKDAT  0x7
+#define SMBTRNSADD 0x9
+#define SMBSLVDATA 0xa
+#define SMLINK_PIN_CTL 0xe
+#define SMBUS_PIN_CTL  0xf 
+
+/* Between 1-10 seconds, We should never timeout normally 
+ * Longer than this is just painful when a timeout condition occurs.
+ */
+#define SMBUS_TIMEOUT (100*1000)
+
+#endif /* I82801ER_H */
diff --git a/src/southbridge/intel/i82801er/i82801er_ac97.c b/src/southbridge/intel/i82801er/i82801er_ac97.c
new file mode 100644
index 0000000000..d16ab84fd9
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_ac97.c
@@ -0,0 +1,41 @@
+/*
+ * (C) 2003 Linux Networx
+ */
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "i82801er.h"
+
+
+static struct device_operations ac97audio_ops  = {
+	.read_resources   = pci_dev_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.enable           = i82801er_enable,
+	.init             = 0,
+	.scan_bus         = 0,
+};
+
+static struct pci_driver ac97audio_driver __pci_driver = {
+	.ops    = &ac97audio_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = PCI_DEVICE_ID_INTEL_82801ER_1F5,
+};
+
+
+static struct device_operations ac97modem_ops  = {
+	.read_resources   = pci_dev_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.enable           = i82801er_enable,
+	.init             = 0,
+	.scan_bus         = 0,
+};
+
+static struct pci_driver ac97modem_driver __pci_driver = {
+	.ops    = &ac97modem_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = PCI_DEVICE_ID_INTEL_82801ER_1F6,
+};
diff --git a/src/southbridge/intel/i82801er/i82801er_early_smbus.c b/src/southbridge/intel/i82801er/i82801er_early_smbus.c
new file mode 100644
index 0000000000..ed014f1a86
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_early_smbus.c
@@ -0,0 +1,156 @@
+
+//#define SMBUS_IO_BASE 0x1000
+#define SMBUS_IO_BASE 0x0f00
+
+#define SMBHSTSTAT 0x0
+#define SMBHSTCTL  0x2
+#define SMBHSTCMD  0x3
+#define SMBXMITADD 0x4
+#define SMBHSTDAT0 0x5
+#define SMBHSTDAT1 0x6
+#define SMBBLKDAT  0x7
+#define SMBTRNSADD 0x9
+#define SMBSLVDATA 0xa
+#define SMLINK_PIN_CTL 0xe
+#define SMBUS_PIN_CTL  0xf 
+
+/* Between 1-10 seconds, We should never timeout normally 
+ * Longer than this is just painful when a timeout condition occurs.
+ */
+#define SMBUS_TIMEOUT (100*1000*10)
+
+static void enable_smbus(void)
+{
+	device_t dev;
+	dev = pci_locate_device(PCI_ID(0x8086, 0x24d3), 0);
+	if (dev == PCI_DEV_INVALID) {
+		die("SMBUS controller not found\r\n");
+	}
+	
+	print_debug("SMBus controller enabled\r\n");
+	/* set smbus iobase */
+	pci_write_config32(dev, 0x20, SMBUS_IO_BASE | 1);
+	/* Set smbus enable */
+	pci_write_config8(dev, 0x40, 0x01);
+	/* Set smbus iospace enable */ 
+	pci_write_config16(dev, 0x4, 0x01);
+	/* Disable interrupt generation */ 
+	outb(0, SMBUS_IO_BASE + SMBHSTCTL);
+	/* clear any lingering errors, so the transaction will run */
+	outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
+}
+
+
+static inline void smbus_delay(void)
+{
+	outb(0x80, 0x80);
+}
+
+static int smbus_wait_until_ready(void)
+{
+	unsigned long loops;
+	loops = SMBUS_TIMEOUT;
+	do {
+		unsigned char val;
+		smbus_delay();
+		val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
+		if ((val & 1) == 0) {
+			break;
+		}
+		if(loops == (SMBUS_TIMEOUT / 2)) {
+			outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), 
+				SMBUS_IO_BASE + SMBHSTSTAT);
+		}
+	} while(--loops);
+	return loops?0:-2;
+}
+
+static int smbus_wait_until_done(void)
+{
+	unsigned long loops;
+	loops = SMBUS_TIMEOUT;
+	do {
+		unsigned char val;
+		smbus_delay();
+		
+		val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
+		if ( (val & 1) == 0) {
+			break;
+		}
+		if ((val & ~((1<<6)|(1<<0)) ) != 0 ) {
+			break;
+		}
+	} while(--loops);
+	return loops?0:-3;
+}
+
+static int smbus_read_byte(unsigned device, unsigned address)
+{
+	unsigned char global_control_register;
+	unsigned char global_status_register;
+	unsigned char byte;
+
+	if (smbus_wait_until_ready() < 0) {
+		return -2;
+	}
+	
+	/* setup transaction */
+	/* disable interrupts */
+	outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xfe, SMBUS_IO_BASE + SMBHSTCTL);
+	/* set the device I'm talking too */
+	outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBXMITADD);
+	/* set the command/address... */
+	outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
+	/* set up for a byte data read */
+	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xe3) | (0x2<<2), SMBUS_IO_BASE + SMBHSTCTL);
+
+	/* clear any lingering errors, so the transaction will run */
+	outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
+
+	/* clear the data byte...*/
+	outb(0, SMBUS_IO_BASE + SMBHSTDAT0);
+
+	/* start a byte read, with interrupts disabled */
+	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), SMBUS_IO_BASE + SMBHSTCTL);
+
+
+	/* poll for transaction completion */
+	if (smbus_wait_until_done() < 0) {
+		return -3;
+	}
+
+	global_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT) & ~(1<<6); /* Ignore the In Use Status... */
+
+	/* read results of transaction */
+	byte = inb(SMBUS_IO_BASE + SMBHSTDAT0);
+
+	if (global_status_register != 2) {
+		return -1;
+	}
+	return byte;
+}
+#if 0
+static void smbus_write_byte(unsigned device, unsigned address, unsigned char val)
+{
+	if (smbus_wait_until_ready() < 0) {
+		return;
+	}
+
+	/* by LYH */
+	outb(0x37,SMBUS_IO_BASE + SMBHSTSTAT);
+	/* set the device I'm talking too */
+	outw(((device & 0x7f) << 1) | 0, SMBUS_IO_BASE + SMBHSTADDR);
+
+	/* data to send */
+	outb(val, SMBUS_IO_BASE + SMBHSTDAT);
+
+	outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
+
+	/* start the command */
+	outb(0xa, SMBUS_IO_BASE + SMBHSTCTL);
+
+	/* poll for transaction completion */
+	smbus_wait_until_done();
+	return;
+}
+#endif
diff --git a/src/southbridge/intel/i82801er/i82801er_ide.c b/src/southbridge/intel/i82801er/i82801er_ide.c
new file mode 100644
index 0000000000..b33a0b0f09
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_ide.c
@@ -0,0 +1,53 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "i82801er.h"
+
+
+static void ide_init(struct device *dev)
+{
+#if ICH5_SATA_ADDRESS_MAP<=1
+	/* Enable ide devices so the linux ide driver will work */
+	uint16_t word;
+	uint8_t byte;
+	int enable_a=1, enable_b=1;
+
+
+	word = pci_read_config16(dev, 0x40);
+	word &= ~((1 << 15));
+	if (enable_a) {
+		/* Enable first ide interface */
+		word |= (1<<15);
+		printk_debug("IDE0 ");
+	}
+	pci_write_config16(dev, 0x40, word);
+
+        word = pci_read_config16(dev, 0x42);
+        word &= ~((1 << 15));
+        if (enable_a) {
+                /* Enable secondary ide interface */
+                word |= (1<<15);
+                printk_debug("IDE1 ");
+        }
+        pci_write_config16(dev, 0x42, word);
+#endif
+
+}
+
+static struct device_operations ide_ops  = {
+	.read_resources   = pci_dev_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.init             = ide_init,
+	.scan_bus         = 0,
+	.enable           = i82801er_enable,
+};
+
+static struct pci_driver ide_driver __pci_driver = {
+	.ops    = &ide_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = PCI_DEVICE_ID_INTEL_82801ER_1F1,
+};
+
diff --git a/src/southbridge/intel/i82801er/i82801er_lpc.c b/src/southbridge/intel/i82801er/i82801er_lpc.c
new file mode 100644
index 0000000000..c1ee7410ed
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_lpc.c
@@ -0,0 +1,219 @@
+/*
+ * (C) 2003 Linux Networx, SuSE Linux AG
+ * (C) 2004 Tyan Computer
+ */
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <device/chip.h>
+#include <pc80/mc146818rtc.h>
+#include "i82801er.h"
+
+void isa_dma_init(void); /* from /pc80/isa-dma.c */
+
+#define NMI_OFF 0
+
+void i82801er_enable_ioapic( struct device *dev) 
+{
+        uint32_t dword;
+        volatile uint32_t *ioapic_sba = (volatile uint32_t *)0xfec00000;
+        volatile uint32_t *ioapic_sbd = (volatile uint32_t *)0xfec00010;
+
+        dword = pci_read_config32(dev, GEN_CNTL);
+        dword |= (3 << 7); /* enable ioapic */
+        dword |= (1 <<13); /* coprocessor error enable */
+        dword |= (1 << 1); /* delay transaction enable */
+        dword |= (1 << 2); /* DMA collection buf enable */
+        pci_write_config32(dev, GEN_CNTL, dword);
+        printk_debug("ioapic southbridge enabled %x\n",dword);
+        *ioapic_sba=0;
+        *ioapic_sbd=(2<<24);
+        //lyh *ioapic_sba=3;
+        //lyh *ioapic_sbd=1;    
+        *ioapic_sba=0;
+        dword=*ioapic_sbd;
+        printk_debug("Southbridge apic id = %x\n",dword);
+        if(dword!=(2<<24))
+                for(;;);
+        //lyh *ioapic_sba=3;
+        //lyh dword=*ioapic_sbd;
+        //lyh printk_debug("Southbridge apic DT = %x\n",dword);
+        //lyh if(dword!=1)
+        //lyh   for(;;);
+
+
+}
+void i82801er_enable_serial_irqs( struct device *dev)
+{
+        pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(1 << 6)|((21 - 17) << 2)|(0<< 0));
+}
+void i82801er_lpc_route_dma( struct device *dev, uint8_t mask) 
+{
+        uint16_t word;
+        int i;
+        word = pci_read_config8(dev, PCI_DMA_CFG);
+        word &= ((1 << 10) - (1 << 8));
+        for(i = 0; i < 8; i++) {
+                if (i == 4)
+                        continue;
+                word |= ((mask & (1 << i))? 3:1) << (i*2);
+        }
+        pci_write_config16(dev, PCI_DMA_CFG, word);
+}
+void i82801er_rtc_init(struct device *dev)
+{
+        uint8_t byte;
+        uint32_t dword;
+        int rtc_failed;
+        byte = pci_read_config8(dev, GEN_PMCON_3);
+        rtc_failed = byte & RTC_FAILED;
+        if (rtc_failed) {
+                byte &= ~(1 << 1); /* preserve the power fail state */
+                pci_write_config8(dev, GEN_PMCON_3, byte);
+        }
+        dword = pci_read_config32(dev, GEN_STS);
+        rtc_failed |= dword & (1 << 2);
+        rtc_init(rtc_failed);
+}
+
+
+void i82801er_1f0_misc(struct device *dev)
+{
+        pci_write_config16(dev, PCICMD, 0x014f);
+        pci_write_config32(dev, PMBASE, 0x00001001);
+        pci_write_config8(dev, ACPI_CNTL, 0x10);
+        pci_write_config32(dev, GPIO_BASE, 0x00001181);
+        pci_write_config8(dev, GPIO_CNTL, 0x10);
+        pci_write_config32(dev, PIRQA_ROUT, 0x0A05030B);
+        pci_write_config8(dev, PIRQE_ROUT, 0x07);
+        pci_write_config8(dev, RTC_CONF, 0x04);
+        pci_write_config8(dev, COM_DEC, 0x10);  //lyh E0->
+        pci_write_config16(dev, LPC_EN, 0x000F);  //LYH 000D->
+}
+
+static void enable_hpet(struct device *dev)
+{
+	const unsigned long hpet_address = 0xfed0000;
+
+        uint32_t dword;
+	uint32_t code = (0 & 0x3);
+        
+        dword = pci_read_config32(dev, GEN_CNTL);
+        dword |= (1 << 17); /* enable hpet */
+	/*Bits [16:15]Memory Address Range
+	00 FED0_0000h - FED0_03FFh
+	01 FED0_1000h - FED0_13FFh
+	10 FED0_2000h - FED0_23FFh
+	11 FED0_3000h - FED0_33FFh*/
+
+        dword &= ~(3 << 15); /* clear it */
+	dword |= (code<<15);
+
+	printk_debug("enabling HPET @0x%x\n", hpet_address | (code <<12) );
+}
+
+static void lpc_init(struct device *dev)
+{
+	uint8_t byte;
+	int pwr_on=-1;
+	int nmi_option;
+
+	/* IO APIC initialization */
+	i82801er_enable_ioapic(dev);
+
+	i82801er_enable_serial_irqs(dev);
+	
+	/* posted memory write enable */
+	byte = pci_read_config8(dev, 0x46);
+	pci_write_config8(dev, 0x46, byte | (1<<0)); 
+
+	/* power after power fail */
+	        /* FIXME this doesn't work! */
+        /* Which state do we want to goto after g3 (power restored)?
+         * 0 == S0 Full On
+         * 1 == S5 Soft Off
+         */
+        pci_write_config8(dev, GEN_PMCON_3, pwr_on?0:1);
+        printk_info("set power %s after power fail\n", pwr_on?"on":"off");
+#if 0
+	/* Enable Error reporting */
+	/* Set up sync flood detected */
+	byte = pci_read_config8(dev, 0x47);
+	byte |= (1 << 1);
+	pci_write_config8(dev, 0x47, byte);
+#endif
+
+	/* Set up NMI on errors */
+	byte = pci_read_config8(dev, 0x61);
+	byte |= (1 << 3); /* IOCHK# NMI Enable */
+	byte |= (1 << 6); /* PCI SERR# Enable */
+	pci_write_config8(dev, 0x61, byte);
+	byte = pci_read_config8(dev, 0x70);
+	nmi_option = NMI_OFF;
+	get_option(&nmi_option, "nmi");
+	if (nmi_option) {			
+		byte |= (1 << 7); /* set NMI */
+		pci_write_config8(dev, 0x70, byte);
+	}
+	
+	/* Initialize the real time clock */
+	i82801er_rtc_init(dev);
+
+	i82801er_lpc_route_dma(dev, 0xff);
+
+	/* Initialize isa dma */
+	isa_dma_init();
+
+	i82801er_1f0_misc(dev);
+	/* Initialize the High Precision Event Timers */
+	enable_hpet(dev);
+}
+
+static void i82801er_lpc_read_resources(device_t dev)
+{
+	unsigned int reg;
+
+	/* Get the normal pci resources of this device */
+	pci_dev_read_resources(dev);
+
+	/* Find my place in the resource list */
+	reg = dev->resources;
+
+	/* Add an extra subtractive resource for both memory and I/O */
+	dev->resource[reg].base  = 0;
+	dev->resource[reg].size  = 0;
+	dev->resource[reg].align = 0;
+	dev->resource[reg].gran  = 0;
+	dev->resource[reg].limit = 0;
+	dev->resource[reg].flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;
+	dev->resource[reg].index = 0;
+	reg++;
+	
+	dev->resource[reg].base  = 0;
+	dev->resource[reg].size  = 0;
+	dev->resource[reg].align = 0;
+	dev->resource[reg].gran  = 0;
+	dev->resource[reg].limit = 0;
+	dev->resource[reg].flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;
+	dev->resource[reg].index = 0;
+	reg++;
+	
+	dev->resources = reg;
+}
+
+static struct device_operations lpc_ops  = {
+	.read_resources   = i82801er_lpc_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.init             = lpc_init,
+	.scan_bus         = scan_static_bus,
+	.enable           = i82801er_enable,
+};
+
+static struct pci_driver lpc_driver __pci_driver = {
+	.ops    = &lpc_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = PCI_DEVICE_ID_INTEL_82801ER_1F0,
+};
diff --git a/src/southbridge/intel/i82801er/i82801er_nic.c b/src/southbridge/intel/i82801er/i82801er_nic.c
new file mode 100644
index 0000000000..4815cf19e0
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_nic.c
@@ -0,0 +1,21 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "i82801er.h"
+
+
+static struct device_operations nic_ops  = {
+	.read_resources   = pci_dev_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.init             = 0,
+	.scan_bus         = 0,
+};
+
+static struct pci_driver nic_driver __pci_driver = {
+	.ops    = &nic_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = 0x1051,
+};
diff --git a/src/southbridge/intel/i82801er/i82801er_pci.c b/src/southbridge/intel/i82801er/i82801er_pci.c
new file mode 100644
index 0000000000..201cedb1a9
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_pci.c
@@ -0,0 +1,33 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "i82801er.h"
+
+static void pci_init(struct device *dev)
+{
+	/* Enable pci error detecting */
+	uint32_t dword;
+	/* System error enable */
+	dword = pci_read_config32(dev, 0x04);
+	dword |= (1<<8); /* SERR# Enable */
+	dword |= (1<<6); /* Parity Error Response */
+	pci_write_config32(dev, 0x04, dword);
+
+}
+
+static struct device_operations pci_ops  = {
+	.read_resources   = pci_bus_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_bus_enable_resources,
+	.init             = pci_init,
+	.scan_bus         = pci_scan_bridge,
+};
+
+static struct pci_driver pci_driver __pci_driver = {
+	.ops    = &pci_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = PCI_DEVICE_ID_INTEL_82801ER_1E0,
+};
+
diff --git a/src/southbridge/intel/i82801er/i82801er_reset.c b/src/southbridge/intel/i82801er/i82801er_reset.c
new file mode 100644
index 0000000000..3d7a4b79b6
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_reset.c
@@ -0,0 +1,7 @@
+#include <arch/io.h>
+
+void hard_reset(void)
+{
+        /* Try rebooting through port 0xcf9 */
+        outb((0 <<3)|(1<<2)|(1<<1), 0xcf9);
+}
diff --git a/src/southbridge/intel/i82801er/i82801er_sata.c b/src/southbridge/intel/i82801er/i82801er_sata.c
new file mode 100644
index 0000000000..b00231e459
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_sata.c
@@ -0,0 +1,75 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "i82801er.h"
+
+static void sata_init(struct device *dev)
+{
+
+        uint16_t word;
+        uint8_t byte;
+	int enable_c=1, enable_d=1;
+	int i;
+                
+        //Enable Serial ATA port
+        byte = pci_read_config8(dev,0x90);
+        byte &= 0xf8;
+        byte |= ICH5_SATA_ADDRESS_MAP & 7;
+        pci_write_config8(dev,0x90,byte);
+
+//        for(i=0;i<10;i++) {
+		word = pci_read_config16(dev,0x92);
+                word &= 0xfffc;
+//                if( (word & 0x0003) == 0x0003) break;
+                word |= 0x0003; // enable P0/P1 
+                pci_write_config16(dev,0x92,word);
+//        }
+
+//        for(i=0;i<10;i++) {
+              /* enable ide0 */
+		word = pci_read_config16(dev, 0x40);
+        	word &= ~(1 << 15);
+                if(enable_c==0) {
+//                     	if( (word & 0x8000) == 0x0000) break;
+                       	word |= 0x0000;
+                }
+                else {
+//                       	if( (word & 0x8000) == 0x8000) break;
+                       	word |= 0x8000;
+                }
+                pci_write_config16(dev, 0x40, word);
+//	}
+                /* enable ide1 */
+//        for(i=0;i<10;i++) {
+              	word = pci_read_config16(dev, 0x42);
+                word &= ~(1 << 15);
+                if(enable_d==0) {
+//                       	if( (word & 0x8000) == 0x0000) break;
+                       	word |= 0x0000;
+                }
+                else {
+//                       	if( (word & 0x8000) == 0x8000) break;
+                       	word |= 0x8000;
+                }
+                pci_write_config16(dev, 0x42, word);
+//        }
+
+}
+
+static struct device_operations sata_ops  = {
+	.read_resources   = pci_dev_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.init             = sata_init,
+	.scan_bus         = 0,
+	.enable           = i82801er_enable,
+};
+
+static struct pci_driver stat_driver __pci_driver = {
+	.ops    = &sata_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = PCI_DEVICE_ID_INTEL_82801ER_1F2_R,
+};
+
diff --git a/src/southbridge/intel/i82801er/i82801er_smbus.c b/src/southbridge/intel/i82801er/i82801er_smbus.c
new file mode 100644
index 0000000000..fd06871234
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_smbus.c
@@ -0,0 +1,92 @@
+#include <smbus.h>
+#include <pci.h>
+#include <arch/io.h>
+
+#define PM_BUS 0
+#define PM_DEVFN PCI_DEVFN(0x1f,3)
+
+#define SMBUS_IO_BASE 0x1000
+#define SMBHSTSTAT 0
+#define SMBHSTCTL  2
+#define SMBHSTCMD  3
+#define SMBHSTADD  4
+#define SMBHSTDAT0 5
+#define SMBHSTDAT1 6
+#define SMBBLKDAT  7
+
+void smbus_enable(void)
+{
+	unsigned char byte;
+	/* iobase addr */
+	pcibios_write_config_dword(PM_BUS, PM_DEVFN, 0x20, SMBUS_IO_BASE | 1);
+	/* smbus enable */
+	pcibios_write_config_byte(PM_BUS, PM_DEVFN, 0x40,  1);
+	/* iospace enable */
+	pcibios_write_config_word(PM_BUS, PM_DEVFN, 0x4, 1);
+
+        /* Disable interrupt generation */
+        outb(0, SMBUS_IO_BASE + SMBHSTCTL);
+
+}
+
+void smbus_setup(void)
+{
+	outb(0, SMBUS_IO_BASE + SMBHSTSTAT);
+}
+
+static void smbus_wait_until_ready(void)
+{
+	while((inb(SMBUS_IO_BASE + SMBHSTSTAT) & 1) == 1) {
+		/* nop */
+	}
+}
+
+static void smbus_wait_until_done(void)
+{
+	unsigned char byte;
+	do {
+		byte = inb(SMBUS_IO_BASE + SMBHSTSTAT);
+	}
+	while((byte &1) == 1);
+	while( (byte & ~1) == 0) {
+		byte = inb(SMBUS_IO_BASE + SMBHSTSTAT);
+	}
+}
+
+int smbus_read_byte(unsigned device, unsigned address, unsigned char *result)
+{
+	unsigned char host_status_register;
+	unsigned char byte;
+
+	smbus_wait_until_ready();
+
+	/* setup transaction */
+	/* disable interrupts */
+	outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & (~1), SMBUS_IO_BASE + SMBHSTCTL);
+	/* set the device I'm talking too */
+	outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBHSTADD);
+	/* set the command/address... */
+	outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
+	/* set up for a byte data read */
+	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xE3) | (0x2 << 2), SMBUS_IO_BASE + SMBHSTCTL);
+
+	/* clear any lingering errors, so the transaction will run */
+	outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
+
+	/* clear the data byte...*/
+	outb(0, SMBUS_IO_BASE + SMBHSTDAT0);
+
+	/* start the command */
+	outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), SMBUS_IO_BASE + SMBHSTCTL);
+
+	/* poll for transaction completion */
+	smbus_wait_until_done();
+
+	host_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT);
+
+	/* read results of transaction */
+	byte = inb(SMBUS_IO_BASE + SMBHSTDAT0);
+
+	*result = byte;
+	return host_status_register != 0x02;
+}
diff --git a/src/southbridge/intel/i82801er/i82801er_usb.c b/src/southbridge/intel/i82801er/i82801er_usb.c
new file mode 100644
index 0000000000..49c6263add
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_usb.c
@@ -0,0 +1,54 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "i82801er.h"
+
+static void usb_init(struct device *dev)
+{
+	uint32_t cmd;
+
+#if 0
+	printk_debug("USB: Setting up controller.. ");
+	cmd = pci_read_config32(dev, PCI_COMMAND);
+	pci_write_config32(dev, PCI_COMMAND, 
+		cmd | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | 
+		PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE);
+
+
+	printk_debug("done.\n");
+#endif
+
+}
+
+static struct device_operations usb_ops  = {
+	.read_resources   = pci_dev_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.init             = usb_init,
+	.scan_bus         = 0,
+	.enable           = i82801er_enable,
+};
+
+static struct pci_driver usb_driver_1 __pci_driver = {
+	.ops    = &usb_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = PCI_DEVICE_ID_INTEL_82801ER_1D0,
+};
+static struct pci_driver usb_driver_2 __pci_driver = {
+        .ops    = &usb_ops,
+        .vendor = PCI_VENDOR_ID_INTEL,
+        .device = PCI_DEVICE_ID_INTEL_82801ER_1D1,
+};
+static struct pci_driver usb_driver_3 __pci_driver = {
+        .ops    = &usb_ops,
+        .vendor = PCI_VENDOR_ID_INTEL,
+        .device = PCI_DEVICE_ID_INTEL_82801ER_1D2,
+};
+static struct pci_driver usb_driver_4 __pci_driver = {
+        .ops    = &usb_ops,
+        .vendor = PCI_VENDOR_ID_INTEL,
+        .device = PCI_DEVICE_ID_INTEL_82801ER_1D3,
+};
+
diff --git a/src/southbridge/intel/i82801er/i82801er_usb2.c b/src/southbridge/intel/i82801er/i82801er_usb2.c
new file mode 100644
index 0000000000..551d4ed3e0
--- /dev/null
+++ b/src/southbridge/intel/i82801er/i82801er_usb2.c
@@ -0,0 +1,39 @@
+//2003 Copywright Tyan
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "i82801er.h"
+
+static void usb2_init(struct device *dev)
+{
+	uint32_t cmd;
+
+#if 0
+	printk_debug("USB: Setting up controller.. ");
+	cmd = pci_read_config32(dev, PCI_COMMAND);
+	pci_write_config32(dev, PCI_COMMAND, 
+		cmd | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | 
+		PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE);
+
+
+	printk_debug("done.\n");
+#endif
+}
+
+static struct device_operations usb2_ops  = {
+	.read_resources   = pci_dev_read_resources,
+	.set_resources    = pci_dev_set_resources,
+	.enable_resources = pci_dev_enable_resources,
+	.init             = usb2_init,
+	.scan_bus         = 0,
+	.enable           = i82801er_enable,
+};
+
+static struct pci_driver usb2_driver __pci_driver = {
+	.ops    = &usb2_ops,
+	.vendor = PCI_VENDOR_ID_INTEL,
+	.device = PCI_DEVICE_ID_INTEL_82801ER_1D7,
+};
diff --git a/src/southbridge/intel/i82870/82870.h b/src/southbridge/intel/i82870/82870.h
new file mode 100644
index 0000000000..f9289d4027
--- /dev/null
+++ b/src/southbridge/intel/i82870/82870.h
@@ -0,0 +1,10 @@
+/* for io apic 1461 */
+#define PCICMD  	0x04
+#define SUBSYS		0x2c
+#define MBAR		0x10
+#define ABAR		0x40
+
+/* for pci bridge  1460 */
+#define MTT	  	0x042
+#define HCCR	  	0x0f0
+#define ACNF	  	0x0e0
diff --git a/src/southbridge/intel/i82870/Config.lb b/src/southbridge/intel/i82870/Config.lb
new file mode 100644
index 0000000000..e6a96517f0
--- /dev/null
+++ b/src/southbridge/intel/i82870/Config.lb
@@ -0,0 +1,3 @@
+driver p64h2_ioapic.o
+driver p64h2_pcibridge.o
+#driver p64h2_pci_parity.o
diff --git a/src/southbridge/intel/i82870/p64h2_ioapic.c b/src/southbridge/intel/i82870/p64h2_ioapic.c
new file mode 100644
index 0000000000..e2bb33883d
--- /dev/null
+++ b/src/southbridge/intel/i82870/p64h2_ioapic.c
@@ -0,0 +1,89 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <pc80/mc146818rtc.h>
+#include "82870.h"
+
+static int ioapic_no = 0;
+
+static void p64h2_ioapic_enable(device_t dev)
+{
+	uint32_t dword;
+	uint16_t word;
+
+	        /* We have to enable MEM and Bus Master for IOAPIC */
+		word = 0x0146;
+		pci_write_config16(dev, PCICMD, word);
+		dword = 0x358015d9;
+		pci_write_config32(dev, SUBSYS, dword);
+
+
+}
+
+static void p64h2_ioapic_init(device_t dev)
+{
+        uint32_t dword;
+        uint16_t word;
+        int i, addr;
+
+        volatile uint32_t *ioapic_a;    /* io apic io memory space command address */
+        volatile uint32_t *ioapic_d;    /* io apic io memory space data address */
+
+        i = ioapic_no++;
+
+                if(i<3)                 /* io apic address numbers are 3,4,5,&8 */
+                        addr=i+3;
+                else
+                        addr=i+5;
+                /* Read the MBAR address for setting up the io apic in io memory space */
+                dword = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
+                ioapic_a = (uint32_t *) dword;
+                ioapic_d = ioapic_a +0x04;
+                printk_debug("IOAPIC %d at %02x:%02x.%01x  MBAR = %x DataAddr = %x\n",
+                        addr, dev->bus->secondary,
+                        PCI_SLOT(dev->path.u.pci.devfn), PCI_FUNC(dev->path.u.pci.devfn),
+                        ioapic_a, ioapic_d);
+
+#if 0
+                dword = (u32)ioapic_a;
+                word = 0x8000 + ((dword >>8)&0x0fff);
+                pci_write_config_word(dev, ABAR, word);
+#endif
+                /* Set up the io apic for the p64h2 - 1461 */
+                *ioapic_a=0;
+                *ioapic_d=(addr<<24); /* Set the address number */
+                *ioapic_a=3;
+                *ioapic_d=1;    /* Enable the io apic */
+
+                /* This code test the setup to see if we really found the io apic */
+                *ioapic_a=0;
+                dword=*ioapic_d;
+                printk_debug("PCI %d apic id = %x\n",addr,dword);
+                if(dword!=(addr<<24))
+                        for(;;);
+                *ioapic_a=3;
+                dword=*ioapic_d;
+                printk_debug("PCI %d apic DT = %x\n",addr,dword);
+                if(dword!=1)
+                        for(;;);
+
+
+}
+
+static struct device_operations ioapic_ops = {
+        .read_resources   = pci_dev_read_resources,
+        .set_resources    = pci_dev_set_resources,
+        .enable_resources = pci_dev_enable_resources,
+        .init     = p64h2_ioapic_init,
+        .scan_bus = 0,
+        .enable   = p64h2_ioapic_enable,
+};
+
+static struct pci_driver ioapic_driver __pci_driver = {
+        .ops    = &ioapic_ops,
+        .vendor = PCI_VENDOR_ID_INTEL,
+        .device = PCI_DEVICE_ID_INTEL_82870_1E0,
+
+};
diff --git a/src/southbridge/intel/i82870/p64h2_pci_parity.c b/src/southbridge/intel/i82870/p64h2_pci_parity.c
new file mode 100644
index 0000000000..d80f9213c9
--- /dev/null
+++ b/src/southbridge/intel/i82870/p64h2_pci_parity.c
@@ -0,0 +1,26 @@
+#include <mem.h>
+#include <pci.h>
+#include <arch/io.h>
+#include <printk.h>
+#
+
+void p64h2_pci_parity_enable(void)
+{
+        uint8_t reg;
+
+        /* 2SERREN - SERR enable for PCI bridge secondary device  */
+        /* 2PEREN  - Parity error for PCI bridge secondary device  */
+        pcibios_read_config_byte(1, ((29 << 3) + (0 << 0)), 0x3e, &reg);
+        reg |= ((1 << 1) + (1 << 0));
+        pcibios_write_config_byte(1, ((29 << 3) + (0 << 0)), 0x3e, reg);
+
+        /* 2SERREN - SERR enable for PCI bridge secondary device  */
+        /* 2PEREN  - Parity error for PCI bridge secondary device  */
+        pcibios_read_config_byte(1, ((31 << 3) + (0 << 0)), 0x3e, &reg);
+        reg |= ((1 << 1) + (1 << 0));
+        pcibios_write_config_byte(1, ((31 << 3) + (0 << 0)), 0x3e, reg);
+
+        return;
+}
+
+
diff --git a/src/southbridge/intel/i82870/p64h2_pcibridge.c b/src/southbridge/intel/i82870/p64h2_pcibridge.c
new file mode 100644
index 0000000000..6f161e900b
--- /dev/null
+++ b/src/southbridge/intel/i82870/p64h2_pcibridge.c
@@ -0,0 +1,39 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <pc80/mc146818rtc.h>
+#include "82870.h"
+
+static void p64h2_pcix_init(device_t dev)
+{
+	uint32_t dword;
+	uint16_t word;
+	uint8_t byte;
+
+
+	/* The purpose of changes to HCCR, ACNF, and MTT is to speed up the 
+	   PCI bus for cards having high speed transfers. */
+	dword = 0xc2040002;
+	pci_write_config32(dev, HCCR, dword);
+	dword = 0x0000c3bf;
+	pci_write_config32(dev, ACNF, dword);
+	byte = 0x08;
+	pci_write_config8(dev, MTT, byte);
+
+}
+static struct device_operations pcix_ops  = {
+        .read_resources   = pci_bus_read_resources,
+        .set_resources    = pci_dev_set_resources,
+        .enable_resources = pci_bus_enable_resources,
+        .init             = p64h2_pcix_init,
+        .scan_bus         = pci_scan_bridge,
+};
+
+static struct pci_driver pcix_driver __pci_driver = {
+        .ops    = &pcix_ops,
+        .vendor = PCI_VENDOR_ID_INTEL,
+        .device = PCI_DEVICE_ID_INTEL_82870_1F0,
+};      
+  
diff --git a/src/superio/winbond/w83627hf/superio.c b/src/superio/winbond/w83627hf/superio.c
index 04a6e2a7e8..ee0a6872e3 100644
--- a/src/superio/winbond/w83627hf/superio.c
+++ b/src/superio/winbond/w83627hf/superio.c
@@ -16,13 +16,100 @@
 #include "chip.h"
 #include "w83627hf.h"
 
-static void init(device_t dev)
+
+void pnp_enter_ext_func_mode(device_t dev) {
+        outb(0x87, dev->path.u.pnp.port);
+        outb(0x87, dev->path.u.pnp.port);
+}
+void pnp_exit_ext_func_mode(device_t dev) {
+        outb(0xaa, dev->path.u.pnp.port);
+}
+
+void pnp_write_hwm(unsigned long port_base, uint8_t reg, uint8_t value)
+{
+        outb(reg, port_base+5);
+        outb(value, port_base+6);
+}
+
+uint8_t pnp_read_hwm(unsigned long port_base, uint8_t reg)
+{
+        outb(reg, port_base + 5);
+        return inb(port_base + 6);
+}       
+
+static void enable_hwm_smbus(device_t dev) {
+	uint8_t reg, value;
+	reg = 0x2b;
+	value = pnp_read_config(dev, reg);
+	value &= 0x3f;
+	pnp_write_config(dev, reg, value);
+}
+
+#if 0
+static void dump_pnp_device(device_t dev)
+{
+        int i;
+        print_debug("\r\n");
+
+        for(i = 0; i <= 255; i++) {
+                uint8_t reg, val;
+                if ((i & 0x0f) == 0) {
+                        print_debug_hex8(i);
+                        print_debug_char(':');
+                }
+		reg = i;
+		if(i!=0xaa) {
+                	val = pnp_read_config(dev, reg);
+		}
+		else {
+			val = 0xaa;
+		}
+                print_debug_char(' ');
+                print_debug_hex8(val);
+                if ((i & 0x0f) == 0x0f) {
+                        print_debug("\r\n");
+                }
+        }
+}
+#endif
+
+static void init_hwm(unsigned long base)
+{
+	uint8_t  reg, value;
+	int i;
+
+	unsigned  hwm_reg_values[] = {
+//	       reg                mask             data
+              0x40     ,       0xff    ,       0x81,  //  ; Start Hardware Monitoring for WIN627
+              0x48     ,       0xaa    ,       0x2a,  //  ; Program SIO SMBus BAR to 54h>>1	
+//              0x48     ,       0xc8    ,       0x48,  //  ; Program SIO SMBus BAR to 90h>>1
+              0x4A     ,       0x21    ,       0x21,  //  ; Program T2 SMBus BAR to 92h>>1 &
+                                                     //  ; Program T3 SMBus BAR to 94h>>1
+              0x4E     ,       0x80    ,       0x00,  
+              0x43     ,       0x00    ,       0xFF,
+              0x44     ,       0x00    ,       0x3F,
+              0x4C     ,       0xBF    ,       0x18,
+              0x4D     ,       0xFF    ,       0x80   //  ; Turn Off Beep
+                                                                            
+	};
+
+	for(i = 0; i<  sizeof(hwm_reg_values)/sizeof(hwm_reg_values[0]); i+=3 ) { 
+		reg = hwm_reg_values[i];	
+	 	value = pnp_read_hwm(base, reg);		
+		value &= 0xff & hwm_reg_values[i+1];
+		value |= 0xff & hwm_reg_values[i+2];
+#if 0
+		printk_debug("base = 0x%04x, reg = 0x%02x, value = 0x%02x\r\n", base,reg,value);
+#endif
+		pnp_write_hwm(base,reg, value);
+	}
+}
+
+
+static void w83627hf_init(device_t dev)
 {
 	struct superio_winbond_w83627hf_config *conf;
 	struct resource *res0, *res1;
-	/* Wishlist handle well known programming interfaces more
-	 * generically.
-	 */
 	if (!dev->enabled) {
 		return;
 	}
@@ -41,15 +128,70 @@ static void init(device_t dev)
 		res1 = get_resource(dev, PNP_IDX_IO1);
 		init_pc_keyboard(res0->base, res1->base, &conf->keyboard);
 		break;
+        case W83627HF_HWM:
+                res0 = get_resource(dev, PNP_IDX_IO0);
+                init_hwm(res0->base);
+                break;
+	}
+	
+}
+
+void w83627hf_pnp_set_resources(device_t dev)
+{
+
+	pnp_enter_ext_func_mode(dev);  
+
+	pnp_set_resources(dev);
+
+#if 0
+        dump_pnp_device(dev);
+#endif
+                
+        pnp_exit_ext_func_mode(dev);  
+        
+}       
+        
+void w83627hf_pnp_enable_resources(device_t dev)
+{       
+        pnp_enter_ext_func_mode(dev);  
+	
+	pnp_enable_resources(dev);               
+
+        switch(dev->path.u.pnp.device) {
+	case W83627HF_HWM:
+		//set the pin 91,92 as I2C bus
+		printk_debug("w83627hf hwm smbus enabled\r\n");
+		enable_hwm_smbus(dev);
+		break;
 	}
+
+#if 0  
+        dump_pnp_device(dev);
+#endif
+
+        pnp_exit_ext_func_mode(dev);  
+
+}
+
+void w83627hf_pnp_enable(device_t dev)
+{
+
+        if (!dev->enabled) {
+                pnp_enter_ext_func_mode(dev);   
+
+                pnp_set_logical_device(dev);
+                pnp_set_enable(dev, 0);
+
+                pnp_exit_ext_func_mode(dev);  
+        }
 }
 
 static struct device_operations ops = {
 	.read_resources   = pnp_read_resources,
-	.set_resources    = pnp_set_resources,
-	.enable_resources = pnp_enable_resources,
-	.enable           = pnp_enable,
-	.init             = init,
+	.set_resources    = w83627hf_pnp_set_resources,
+	.enable_resources = w83627hf_pnp_enable_resources,
+	.enable           = w83627hf_pnp_enable,
+	.init             = w83627hf_init,
 };
 
 static struct pnp_info pnp_dev_info[] = {
@@ -61,8 +203,8 @@ static struct pnp_info pnp_dev_info[] = {
         { &ops, W83627HF_KBC,  PNP_IO0 | PNP_IO1 | PNP_IRQ0 | PNP_IRQ1, { 0x7ff, 0 }, { 0x7ff, 0x4}, },
         { &ops, W83627HF_CIR, PNP_IO0 | PNP_IRQ0, { 0x7f8, 0 }, },
         { &ops, W83627HF_GAME_MIDI_GPIO1, PNP_IO0 | PNP_IO1 | PNP_IRQ0, { 0x7ff, 0 }, {0x7fe, 4} },
-        { &ops, W83627HF_GPIO2, PNP_IO0 | PNP_IO1 | PNP_IRQ0, { 0x7ff, 0 }, {0x7fe, 4} },
-        { &ops, W83627HF_GPIO3, PNP_IO0 | PNP_IO1 | PNP_IRQ0, { 0x7ff, 0 }, {0x7fe, 4} },
+        { &ops, W83627HF_GPIO2,},
+        { &ops, W83627HF_GPIO3,},
         { &ops, W83627HF_ACPI, PNP_IRQ0,  },
         { &ops, W83627HF_HWM,  PNP_IO0 | PNP_IRQ0, { 0xff8, 0 } },
 };
@@ -77,3 +219,4 @@ struct chip_control superio_winbond_w83627hf_control = {
 	.enumerate = enumerate,
 	.name      = "Winbond w83627hf"
 };
+
diff --git a/targets/tyan/s2735/Config.lb b/targets/tyan/s2735/Config.lb
new file mode 100644
index 0000000000..7a3faf4f9c
--- /dev/null
+++ b/targets/tyan/s2735/Config.lb
@@ -0,0 +1,265 @@
+# Sample config file for 
+# the Tyan s2735
+# This will make a target directory of ./s2735
+
+loadoptions
+
+target s2735
+
+uses ARCH
+uses CONFIG_COMPRESS
+uses CONFIG_IOAPIC
+uses CONFIG_ROM_STREAM
+uses CONFIG_ROM_STREAM_START
+uses CONFIG_SMP
+uses CONFIG_UDELAY_TSC
+uses CPU_FIXUP
+uses FALLBACK_SIZE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses i586
+uses i686
+uses INTEL_PPRO_MTRR
+uses HEAP_SIZE
+uses IRQ_SLOT_COUNT
+uses MAINBOARD
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+#uses MEMORY_HOLE
+uses PAYLOAD_SIZE
+uses _RAMBASE
+uses _ROMBASE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_OFFSET
+uses ROM_SECTION_SIZE
+uses ROM_SIZE
+uses STACK_SIZE
+uses USE_FALLBACK_IMAGE
+uses USE_OPTION_TABLE
+uses HAVE_OPTION_TABLE
+uses CONFIG_CHIP_CONFIGURE
+
+uses CONFIG_CONSOLE_BTEXT 
+uses CONFIG_CONSOLE_SERIAL8250
+uses TTYS0_BAUD
+#SMDC Support
+#uses CONFIG_CONSOLE_SERIAL8250_2
+#uses TTYS1_BAUD
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses DEBUG
+uses CONFIG_MAX_CPUS
+uses CONFIG_LOGICAL_CPUS
+uses CONFIG_MAX_PHYSICAL_CPUS
+uses LINUXBIOS_EXTRA_VERSION
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+
+uses CONFIG_FS_STREAM
+uses CONFIG_IDE
+
+uses HAVE_HARD_RESET
+
+#uses CONFIG_VGABIOS
+#uses CONFIG_REALMODE_IDT
+#uses CONFIG_PCIBIOS
+#uses VGABIOS_START
+#uses SCSIFW_START
+
+#
+#uses CONFIG_LSI_SCSI_FW_FIXUP
+
+option HAVE_OPTION_TABLE=1
+option HAVE_MP_TABLE=1
+option CPU_FIXUP=1
+option CONFIG_UDELAY_TSC=0
+option i686=1
+option i586=1
+option INTEL_PPRO_MTRR=1
+#option ROM_SIZE=524288
+option ROM_SIZE=1048576
+
+option HAVE_HARD_RESET=1
+
+#option CONFIG_CONSOLE_BTEXT=1
+#option CONFIG_VGABIOS=1
+#option CONFIG_REALMODE_IDT=1
+#option CONFIG_PCIBIOS=1
+#option VGABIOS_START=0xfff8c000
+#option SCSIFW_START=0xfff80000
+
+#option CONFIG_FS_STREAM=1
+#option CONFIG_IDE=1
+
+option HAVE_FALLBACK_BOOT=1
+  
+# use the new chip configure code.
+
+option CONFIG_CHIP_CONFIGURE=1
+#option CONFIG_LSI_SCSI_FW_FIXUP=1
+
+
+#
+###
+### Build code to export a programmable irq routing table
+###
+option HAVE_PIRQ_TABLE=1
+option IRQ_SLOT_COUNT=15
+#
+###
+### Build code for SMP support
+### Only worry about 2 micro processors
+###
+option CONFIG_SMP=1
+option CONFIG_MAX_CPUS=4
+option CONFIG_LOGICAL_CPUS=1
+option CONFIG_MAX_PHYSICAL_CPUS=2
+#
+###
+### Build code to setup a generic IOAPIC
+###
+option CONFIG_IOAPIC=1
+#
+###
+### MEMORY_HOLE instructs earlymtrr.inc to
+### enable caching from 0-640KB and to disable 
+### caching from 640KB-1MB using fixed MTRRs 
+###
+### Enabling this option breaks SMP because secondary
+### CPU identification depends on only variable MTRRs
+### being enabled.
+###
+#option MEMORY_HOLE=0
+#
+###
+### Clean up the motherboard id strings
+###
+option MAINBOARD_PART_NUMBER="S2735"
+option MAINBOARD_VENDOR="Tyan"
+###
+### Compute the location and size of where this firmware image
+### (linuxBIOS plus bootloader) will live in the boot rom chip.
+###
+#option FALLBACK_SIZE=524288
+#option FALLBACK_SIZE=98304
+option FALLBACK_SIZE=131072
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+option ROM_IMAGE_SIZE=65536
+ 
+
+###
+### Compute where this copy of linuxBIOS will start in the boot rom
+###
+#
+###
+
+## We do use compressed image
+option CONFIG_COMPRESS=1
+
+option CONFIG_CONSOLE_SERIAL8250=1
+option TTYS0_BAUD=115200
+
+#SMDC support
+#option CONFIG_CONSOLE_SERIAL8250_2=1
+#option TTYS1_BAUD=19200
+
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG      1   system is unusable
+## ALERT      2   action must be taken immediately
+## CRIT       3   critical conditions
+## ERR        4   error conditions
+## WARNING    5   warning conditions
+## NOTICE     6   normal but significant condition
+## INFO       7   informational
+## DEBUG      8   debug-level messages
+## SPEW       9   Way too many details
+
+## Request this level of debugging output
+option DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+option MAXIMUM_CONSOLE_LOGLEVEL=8
+
+option DEBUG=1
+
+#
+
+## LinuxBIOS C code runs at this location in RAM
+option _RAMBASE=0x004000
+
+##
+## Use a 32K stack  
+##
+option STACK_SIZE=0x8000
+
+##
+## Use a 56K heap 
+##
+option HEAP_SIZE=0xe000
+
+#
+###
+### Compute the start location and size size of
+### The linuxBIOS bootloader.
+###
+option CONFIG_ROM_STREAM     = 1
+
+#
+# 
+romimage "normal"
+#	48K for SCSI FW
+#        option ROM_SIZE = 475136
+#	48K for SCSI FW and 48K for ATI ROM
+#	option ROM_SIZE = 425984  
+#       64K for Etherboot
+#        option ROM_SIZE = 458752
+        option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
+        option USE_FALLBACK_IMAGE=0
+	option ROM_SECTION_SIZE  = (ROM_SIZE - FALLBACK_SIZE)
+	option ROM_SECTION_OFFSET= 0
+
+	option PAYLOAD_SIZE            = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
+	option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+	option _ROMBASE      = (CONFIG_ROM_STREAM_START + PAYLOAD_SIZE)
+
+#	option XIP_ROM_SIZE = FALLBACK_SIZE
+	option XIP_ROM_SIZE = 65536
+	option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
+
+	mainboard tyan/s2735
+#	payload ../../../payloads/e1000--ide_disk.zelf
+#        payload ../../../payloads/filo.elf
+#        payload ../../../payloads/filo_mem.elf
+#	payload ../../../payloads/filo_mem_btext.elf
+#	payload ../../../payloads/filo_btext.zelf
+	payload ../../../payloads/e1000--filo_btext.zelf
+end
+
+romimage "fallback" 
+	option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
+	option USE_FALLBACK_IMAGE=1
+	option ROM_SECTION_SIZE  = FALLBACK_SIZE
+	option ROM_SECTION_OFFSET= (ROM_SIZE - FALLBACK_SIZE)
+
+	option PAYLOAD_SIZE            = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
+	option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+	option _ROMBASE      = (CONFIG_ROM_STREAM_START + PAYLOAD_SIZE)
+
+#	option XIP_ROM_SIZE = FALLBACK_SIZE
+        option XIP_ROM_SIZE = 65536
+	option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
+
+	mainboard tyan/s2735
+#	payload ../../../payloads/e1000--ide_disk.zelf
+#        payload ../../../payloads/filo_mem.elf
+#	payload ../../../payloads/filo_mem_btext.elf
+#	payload ../../../payloads/e1000_btext.zelf
+	payload ../../../payloads/e1000--filo_btext.zelf
+	
+end
+
+buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"
diff --git a/targets/tyan/s2735/VERSION b/targets/tyan/s2735/VERSION
new file mode 100644
index 0000000000..cd5ac039d6
--- /dev/null
+++ b/targets/tyan/s2735/VERSION
@@ -0,0 +1 @@
+2.0
diff --git a/targets/tyan/s2735/ns2735 b/targets/tyan/s2735/ns2735
new file mode 100644
index 0000000000..f983eb4033
--- /dev/null
+++ b/targets/tyan/s2735/ns2735
@@ -0,0 +1,8 @@
+#!/bin/bash
+TYANMB=s27i35
+cd "$TYANMB"
+make
+#cat ../fwx.rom ../atix.rom ./normal/linuxbios.rom ./fallback/linuxbios.rom > $TYANMB"_linuxbios.rom"
+#cat ../fwx.rom ./normal/linuxbios.rom ./fallback/linuxbios.rom > $TYANMB"_linuxbios.rom"
+cat ./normal/linuxbios.rom ./fallback/linuxbios.rom > $TYANMB"_linuxbios.rom"
+cp -f $TYANMB"_linuxbios.rom" /home/yhlu/
author	Yinghai Lu <yinghailu@gmail.com>	2004-07-01 03:55:03 +0000
committer	Yinghai Lu <yinghailu@gmail.com>	2004-07-01 03:55:03 +0000
commit	70093f7875371abe52c4417c6cc3a427d20781c5 (patch)
tree	f5812172eab817e66840583c669f16d4b1121531
parent	7dea9552d5fa10c5542e744fe1d8e0a81689e3c1 (diff)