soc/qualcomm: Increase SPI frequency to 75 MHz

Increase frequency of sc7280 to 75 MHz.  Setting the delay to 1/8 of
a cycle as a result of experimentation.

BUG=b:190231148
BRANCH=None
TEST=Make sure that herobrine board boots
     HW Engineer measured SPI frequency and verified running at 75 MHz

Signed-off-by: Shelley Chen <shchen@google.com>
Change-Id: I3cf5a7c85f12800a11ece397a354349f2a0a235f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64673
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>

5 files changed, 48 insertions, 7 deletions

diff --git a/src/soc/qualcomm/common/include/soc/qspi_common.h b/src/soc/qualcomm/common/include/soc/qspi_common.h
index a0f612c04f..6a1496aed1 100644
--- a/src/soc/qualcomm/common/include/soc/qspi_common.h
+++ b/src/soc/qualcomm/common/include/soc/qspi_common.h
@@ -26,6 +26,7 @@ struct qcom_qspi_regs {
 	u32 current_mem_addr;
 	u32 hw_version;
 	u32 rd_fifo[16];
+	u32 sampling_clk_cfg;
 };
 
 check_member(qcom_qspi_regs, rd_fifo, 0x50);
@@ -97,7 +98,16 @@ static struct qcom_qspi_regs * const qcom_qspi = (void *) QSPI_BASE;
 
 #define QSPI_MAX_PACKET_COUNT 0xFFC0
 
-void quadspi_init(uint32_t hz);
+/*
+ * quadspi_init(): Configure SPI
+ *
+ * @param hz:      SPI frequency in Hz
+ * @param sdelay:  sampling delay in sdelay/8 cycle units example, if sdelay=1,
+ *                 then will delay sampling clock by 1/8 cycle.  Note that
+ *                 setting sdelay to 4-7 would result in a negative sampling
+ *                 delay compared to 0.
+ */
+void quadspi_init(uint32_t hz, uint32_t sdelay);
 int qspi_claim_bus(const struct spi_slave *slave);
 int qspi_setup_bus(const struct spi_slave *slave);
 void qspi_release_bus(const struct spi_slave *slave);
diff --git a/src/soc/qualcomm/common/qspi.c b/src/soc/qualcomm/common/qspi.c
index 448fb86145..1c345ccf12 100644
--- a/src/soc/qualcomm/common/qspi.c
+++ b/src/soc/qualcomm/common/qspi.c
@@ -221,11 +221,26 @@ static void queue_data(uint8_t *data, uint32_t data_bytes,
 		queue_bounce_data(epilog_ptr, epilog_bytes, data_mode, write);
 }
 
-static void reg_init(void)
+/*
+ * The way to encode the sampling delay is:
+ *
+ * QSPI_SAMPLE_CLK_CONFIG	delay (cycle)
+ * ----------------------------------------
+ * 0xFFFh = 1111 1111 1111b	7/8
+ * 0xDB6h = 1101 1011 0110b	6/8
+ * 0xB6Dh = 1011 0110 1101b	5/8
+ * 0x924h = 1001 0010 0100b	4/8
+ * 0x6DBh = 0110 1101 1011b	3/8
+ * 0x492h = 0100 1001 0010b	2/8
+ * 0x249h = 0010 0100 1001b	1/8
+ * 0x000h = 0000 0000 0000b	None
+ */
+static void reg_init(uint32_t sdelay)
 {
 	uint32_t spi_mode;
 	uint32_t tx_data_oe_delay, tx_data_delay;
 	uint32_t mstr_config;
+	uint32_t sampling_delay;
 
 	spi_mode = 0;
 
@@ -236,7 +251,6 @@ static void reg_init(void)
 		(tx_data_delay << TX_DATA_DELAY_SHIFT) | (SBL_EN) |
 		(spi_mode << SPI_MODE_SHIFT) |
 		(PIN_HOLDN) |
-		(FB_CLK_EN) |
 		(DMA_ENABLE) |
 		(FULL_CYCLE_MODE);
 
@@ -246,14 +260,16 @@ static void reg_init(void)
 	write32(&qcom_qspi->mstr_int_sts, 0xFFFFFFFF);
 	write32(&qcom_qspi->rd_fifo_cfg, 0x0);
 	write32(&qcom_qspi->rd_fifo_rst, RESET_FIFO);
+	sampling_delay = sdelay << 9 | sdelay << 6 | sdelay << 3 | sdelay << 0;
+	write32(&qcom_qspi->sampling_clk_cfg, sampling_delay);
 }
 
-void quadspi_init(uint32_t hz)
+void quadspi_init(uint32_t hz, uint32_t sdelay)
 {
 	assert(dcache_line_bytes() == CACHE_LINE_SIZE);
 	clock_configure_qspi(hz * 4);
 	configure_gpios();
-	reg_init();
+	reg_init(sdelay);
 }
 
 int qspi_claim_bus(const struct spi_slave *slave)
diff --git a/src/soc/qualcomm/sc7180/bootblock.c b/src/soc/qualcomm/sc7180/bootblock.c
index 365b7d4460..c108157573 100644
--- a/src/soc/qualcomm/sc7180/bootblock.c
+++ b/src/soc/qualcomm/sc7180/bootblock.c
@@ -8,6 +8,6 @@
 void bootblock_soc_init(void)
 {
 	clock_init();
-	quadspi_init(37500 * KHz);
+	quadspi_init(37500 * KHz, 0);
 	qupv3_fw_init();
 }
diff --git a/src/soc/qualcomm/sc7280/bootblock.c b/src/soc/qualcomm/sc7280/bootblock.c
index bdabea1fbb..0926127baf 100644
--- a/src/soc/qualcomm/sc7280/bootblock.c
+++ b/src/soc/qualcomm/sc7280/bootblock.c
@@ -8,6 +8,11 @@
 void bootblock_soc_init(void)
 {
 	clock_init();
-	quadspi_init(50000 * KHz);
+	/*
+	 * Through experimentation, we have determined
+	 * that a delay of 1/8 cycle is best for herobrine.
+	 * See b/190231148
+	 */
+	quadspi_init(75000 * KHz, 1);
 	qupv3_fw_init();
 }
diff --git a/src/soc/qualcomm/sc7280/clock.c b/src/soc/qualcomm/sc7280/clock.c
index 4441e48083..7b017c4d80 100644
--- a/src/soc/qualcomm/sc7280/clock.c
+++ b/src/soc/qualcomm/sc7280/clock.c
@@ -28,6 +28,16 @@ static struct clock_freq_config qspi_core_cfg[] = {
 		.div = QCOM_CLOCK_DIV(3),
 	},
 	{
+		.hz = 240 * MHz,
+		.src = SRC_GPLL0_MAIN_600MHZ,
+		.div = QCOM_CLOCK_DIV(2.5),
+	},
+	{
+		.hz = 300 * MHz,
+		.src = SRC_GPLL0_MAIN_600MHZ,
+		.div = QCOM_CLOCK_DIV(2),
+	},
+	{
 		.hz = 400 * MHz,
 		.src = SRC_GPLL0_MAIN_600MHZ,
 		.div = QCOM_CLOCK_DIV(1.5),