diff options
Diffstat (limited to 'configs/gps/gps.conf')
| -rw-r--r-- | configs/gps/gps.conf | 212 |
1 files changed, 0 insertions, 212 deletions
diff --git a/configs/gps/gps.conf b/configs/gps/gps.conf deleted file mode 100644 index 54036df..0000000 --- a/configs/gps/gps.conf +++ /dev/null @@ -1,212 +0,0 @@ -#Uncommenting these urls would only enable -#the power up auto injection and force injection(test case). -#XTRA_SERVER_1=http://xtrapath1.izatcloud.net/xtra2.bin -#XTRA_SERVER_2=http://xtrapath2.izatcloud.net/xtra2.bin -#XTRA_SERVER_3=http://xtrapath3.izatcloud.net/xtra2.bin - -#Version check for XTRA -#DISABLE = 0 -#AUTO = 1 -#XTRA2 = 2 -#XTRA3 = 3 -XTRA_VERSION_CHECK=0 - -XTRA_TEST_ENABLED = 1 -XTRA_THROTTLE_ENABLED = 0 - - - -# Error Estimate -# _SET = 1 -# _CLEAR = 0 -ERR_ESTIMATE=0 - -#NTP server -NTP_SERVER=time.izatcloud.net - -#XTRA CA path -XTRA_CA_PATH=/system/etc/security/cacerts - -# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info -# 4 - Debug, 5 - Verbose -# If DEBUG_LEVEL is commented, Android's logging levels will be used -DEBUG_LEVEL = 5 - -# Intermediate position report, 1=enable, 0=disable -INTERMEDIATE_POS=0 - -# Below bit mask configures how GPS functionalities -# should be locked when user turns off GPS on Settings -# Set bit 0x1 if MO GPS functionalities are to be locked -# Set bit 0x2 if NI GPS functionalities are to be locked -# default - non is locked for backward compatibility -#GPS_LOCK = 0 - -# supl version 1.0 -SUPL_VER=0x20000 - -# Emergency SUPL, 1=enable, 0=disable -#SUPL_ES=0 - -#Choose PDN for Emergency SUPL -#1 - Use emergency PDN -#0 - Use regular SUPL PDN for Emergency SUPL -USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0 - -#SUPL_MODE is a bit mask set in config.xml per carrier by default. -#If it is uncommented here, this value will overwrite the value from -#config.xml. -#MSA=0X2 -#MSB=0X1 -#SUPL_MODE= - -# GPS Capabilities bit mask -# SCHEDULING = 0x01 -# MSB = 0x02 -# MSA = 0x04 -# ON_DEMAND_TIME = 0x10 -# GEOFENCE = 0x20 -# default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING | GEOFENCE -CAPABILITIES=0x37 - -# Accuracy threshold for intermediate positions -# less accurate positions are ignored, 0 for passing all positions -# ACCURACY_THRES=5000 - -################################ -##### AGPS server settings ##### -################################ - -# FOR SUPL SUPPORT, set the following -SUPL_HOST=supl.qxwz.com -SUPL_PORT=7275 - -# FOR C2K PDE SUPPORT, set the following -# C2K_HOST=c2k.pde.com or IP -# C2K_PORT=1234 - -# Bitmask of slots that are available -# for write/install to, where 1s indicate writable, -# and the default value is 0 where no slots -# are writable. For example, AGPS_CERT_WRITABLE_MASK -# of b1000001010 makes 3 slots available -# and the remaining 7 slots unwritable. -#AGPS_CERT_WRITABLE_MASK=0 - -#################################### -# LTE Positioning Profile Settings -#################################### -# 0: Enable RRLP on LTE(Default) -# 1: Enable LPP_User_Plane on LTE -# 2: Enable LPP_Control_Plane -# 3: Enable both LPP_User_Plane and LPP_Control_Plane -LPP_PROFILE = 3 - -################################ -# EXTRA SETTINGS -################################ -# NMEA provider (1=Modem Processor, 0=Application Processor) -NMEA_PROVIDER=0 -# Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE) -SGLTE_TARGET=0 - -################################################## -# Select Positioning Protocol on A-GLONASS system -################################################## -# 0x1: RRC CPlane -# 0x2: RRLP UPlane -# 0x4: LLP Uplane -A_GLONASS_POS_PROTOCOL_SELECT = 0 - -################################################## -# Select technology for LPPe Control Plane -################################################## -# 0x1: DBH for LPPe CP -# 0x2: WLAN AP Measurements for LPPe CP -# 0x4: SRN AP measurement for CP -# 0x8: Sensor Barometer Measurement LPPe CP -LPPE_CP_TECHNOLOGY = 0 - -################################################## -# Select technology for LPPe User Plane -################################################## -# 0x1: DBH for LPPe UP -# 0x2: WLAN AP Measurements for LPPe UP -# 0x4: SRN AP measurement for UP -# 0x8: Sensor Barometer Measurement LPPe UP -LPPE_UP_TECHNOLOGY = 0 - -################################################## -# AGPS_CONFIG_INJECT -################################################## -# enable/disable injection of AGPS configurations: -# SUPL_VER -# SUPL_HOST -# SUPL_PORT -# C2K_HOST -# C2K_PORT -# LPP_PROFILE -# A_GLONASS_POS_PROTOCOL_SELECT -# 0: disable -# 1: enable -AGPS_CONFIG_INJECT = 1 - -################################################## -# GNSS settings for automotive use cases -# Configurations in following section are -# specific to automotive use cases, others -# please do not change, keep the default values -################################################## - -# AP Coarse Timestamp Uncertainty -################################################## -# default : 10 -# AP time stamp uncertainty, until GNSS receiver -# is able to acquire better timing information -AP_TIMESTAMP_UNCERTAINTY = 10 - -################################################## -# QDR engine availability status -################################################## -# 0 : NO QDR (default) -# 1 : QDR enabled -# This settings enables QDR Configuration for -# automotive use case, if enabled then -# DR_AP_Service needs to be enabled in izat.conf -#EXTERNAL_DR_ENABLED = 0 - -##################################### -# DR_SYNC Pulse Availability -##################################### -# 0 : DR_SYNC pulse not available (default) -# 1 : DR_SYNC pulse available -# This configuration enables the driver to make use -# of PPS events generated by DR_SYNC pulse -# Standard Linux PPS driver needs to be enabled -DR_SYNC_ENABLED = 0 - -##################################### -# PPS Device name -##################################### -PPS_DEVICENAME = /dev/pps0 - -##################################### -# AP Clock Accuracy -##################################### -# Quality of APPS processor clock (in PPM). -# Value specified is used for calculation of -# APPS time stamp uncertainty -AP_CLOCK_PPM = 100 - -##################################### -# MAX ms difference to detect missing pulse -##################################### -# Specifies time threshold in ms to validate any missing PPS pulses -MISSING_PULSE_TIME_DELTA = 900 - -##################################### -# Propagation time uncertainty -##################################### -# This settings enables time uncertainty propagation -# logic incase of missing PPS pulse -PROPAGATION_TIME_UNCERTAINTY = 1 |