diff options
Diffstat (limited to 'WCNSS_qcom_cfg.ini')
| -rw-r--r-- | WCNSS_qcom_cfg.ini | 612 |
1 files changed, 612 insertions, 0 deletions
diff --git a/WCNSS_qcom_cfg.ini b/WCNSS_qcom_cfg.ini new file mode 100644 index 0000000..7f49593 --- /dev/null +++ b/WCNSS_qcom_cfg.ini @@ -0,0 +1,612 @@ +# This file allows user to override the factory + +# defaults for the WLAN Driver + + +# Enable IMPS or not +gEnableImps=1 + +# Enable/Disable Idle Scan + +gEnableIdleScan=0 + + +# Increase sleep duration (seconds) during IMPS +# 0 implies no periodic wake up from IMPS. Periodic wakeup is +# unnecessary if Idle Scan is disabled. +gImpsModSleepTime=0 + + +# Enable BMPS or not +gEnableBmps=1 + +# Enable suspend or not + +# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter + +gEnableSuspend=3 + + +# Phy Mode (auto, b, g, n, etc) +# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac +# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only +# 7 = 11b only 8 = 11ac only. +gDot11Mode=0 + + +# CSR Roaming Enable(1) Disable(0) + +gRoamingTime=0 + + +# Assigned MAC Addresses - This will be used until NV items are in place + +# Each byte of MAC address is represented in Hex format as XX + +Intf0MacAddress=000AF58989FF +Intf1MacAddress=000AF58989FE +Intf2MacAddress=000AF58989FD + +Intf3MacAddress=000AF58989FC + + +# UAPSD service interval for VO,VI, BE, BK traffic + +InfraUapsdVoSrvIntv=0 + +InfraUapsdViSrvIntv=0 + +InfraUapsdBeSrvIntv=0 + +InfraUapsdBkSrvIntv=0 + +# Flag to allow STA send AddTspec even when ACM is Off +gAddTSWhenACMIsOff=1 + +# Make 1x1 the default antenna configuration + +gNumRxAnt=1 + + +# Beacon filtering frequency (unit in beacon intervals) + +gNthBeaconFilter=50 + + +# Enable WAPI or not + +# WAPIIsEnabled=0 + + +# Flags to filter Mcast abd Bcast RX packets. + +# Value 0: No filtering, 1: Filter all Multicast. + +# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast + +McastBcastFilter=3 + + +#Flag to enable HostARPOffload feature or not + +hostArpOffload=1 + +#Flag to enable HostNSOffload feature or not + +hostNSOffload=1 + +#SoftAP Related Parameters + +# AP MAc addr + +gAPMacAddr=000AF589dcab + + +# 802.11n Protection flag + +gEnableApProt=1 + + +#Enable OBSS protection + +gEnableApOBSSProt=1 + + +#Enable/Disable UAPSD for SoftAP + +gEnableApUapsd=1 + + +# Fixed Rate + +gFixedRate=0 + + +# Maximum Tx power + +# gTxPowerCap=30 + + +# Fragmentation Threshold + +# gFragmentationThreshold=2346 + + +# RTS threshold + +RTSThreshold=1048576 + + +# Intra-BSS forward + +gDisableIntraBssFwd=0 + + +# WMM Enable/Disable + +WmmIsEnabled=0 + + +# 802.11d support + +g11dSupportEnabled=0 + +# 802.11h support + +g11hSupportEnabled=1 + +# DFS Master Capability +gEnableDFSMasterCap=1 + +# ESE Support and fast transition +EseEnabled=1 +ImplicitQosIsEnabled=0 +gNeighborScanTimerPeriod=200 + +gNeighborLookupThreshold=76 +gNeighborReassocThreshold=81 + +gNeighborScanChannelMinTime=20 +gNeighborScanChannelMaxTime=30 +gMaxNeighborReqTries=3 + +# Legacy (non-ESE, non-802.11r) Fast Roaming Support +# To enable, set FastRoamEnabled=1 +# To disable, set FastRoamEnabled=0 +FastRoamEnabled=1 + +#Check if the AP to which we are roaming is better than current AP in terms of RSSI. +#Checking is disabled if set to Zero.Otherwise it will use this value as to how better +#the RSSI of the new/roamable AP should be for roaming +RoamRssiDiff=3 + +# If the RSSI of any available candidate is better than currently associated +# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without +# registering for reassoc threshold). +# NOTE: Value of 0 means that we would register for reassoc threshold. +gImmediateRoamRssiDiff=10 + +# To enable, set gRoamIntraBand=1 (Roaming within band) +# To disable, set gRoamIntraBand=0 (Roaming across band) +gRoamIntraBand=0 + +#Short Guard Interval Enable/disable + +gShortGI20Mhz=1 + +gShortGI40Mhz=1 + + +#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled + +gAPAutoShutOff=0 + +#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec +gWlanAutoShutdown = 0 + +# Not used. +gApAutoChannelSelection=0 + + +# Listen Energy Detect Mode Configuration + +# Valid values 0-128 + +# 128 means disable Energy Detect feature + +# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. + +# 10-128 are reserved. + +# The EDET threshold mapping is as follows in 3dB step: + +# 0 = -60 dBm + +# 1 = -63 dBm + +# 2 = -66 dBm + +# ... + +# 7 = -81 dBm + +# 8 = -84 dBm + +# 9 = -87 dBm + +# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: + +# + +# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. + +# + +gEnablePhyAgcListenMode=128 + + +#Preferred band (both or 2.4 only or 5 only) + +BandCapability=0 + + +#Beacon Early Termination (1 = enable the BET feature, 0 = disable) + +enableBeaconEarlyTermination=0 + +beaconEarlyTerminationWakeInterval=3 + + +#Channel Bonding +gChannelBondingMode5GHz=1 + + +#Enable Keep alive with non-zero period value + +gStaKeepAlivePeriod = 30 + +#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). +#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) +#For both active and power save clients. + +#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. +#If doesn't honor for 5 seconds then DUT remove client. + +#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on +#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. +#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. + +#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period +#where we send NULL frame. + +#gApLinkMonitorPeriod = 10 + +#gGoLinkMonitorPeriod = 10 + +#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. +#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. + + +gGoKeepAlivePeriod = 20 + +gApKeepAlivePeriod = 20 + + +#If set will start with active scan after driver load, otherwise will start with + +#passive scan to find out the domain + +gEnableBypass11d=1 + + +#If set to 0, will not scan DFS channels + +gEnableDFSChnlScan=1 + +# Enable DFS channel roam +# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE +gAllowDFSChannelRoam=1 + +gVhtChannelWidth=2 + +# Enable Automatic Tx Power control + +gEnableAutomaticTxPowerControl=1 + +# 0 for OLPC 1 for CLPC and SCPC +gEnableCloseLoop=1 + +#Data Inactivity Timeout when in powersave (in ms) +gDataInactivityTimeout=200 + +# Set txchainmask and rxchainmask +# These parameters are used only if gEnable2x2 is 0 +# Valid values are 1,2 +# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. +# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. +gSetTxChainmask1x1=1 +gSetRxChainmask1x1=1 + +# Scan Timing Parameters +# gPassiveMaxChannelTime=110 +# gPassiveMinChannelTime=60 +gActiveMaxChannelTime=40 +gActiveMinChannelTime=20 + +#If set to 0, MCC is not allowed. +gEnableMCCMode=1 + +# MCC to SCC Switch mode: +# 0-Disable +# 1-Enable +# 2-Force SCC if same band, with SAP restart +# 3-Force SCC if same band, without SAP restart by sending (E)CSA +# 4-Force SCC if same band (or) use SAP mandatory channel for DBS, +# without SAP restart by sending (E)CSA +gWlanMccToSccSwitchMode = 0 + +# 1=enable STBC; 0=disable STBC +gEnableRXSTBC=1 + +# 1=enable tx STBC; 0=disable +gEnableTXSTBC=1 + +# 1=enable rx LDPC; 0=disable +gEnableRXLDPC=0 + +#Enable/Disable Tx beamforming +gTxBFEnable=1 + +#Enable/Disable Tx beamformee in SAP mode +gEnableTxBFeeSAP=1 + +# Enable Tx beamforming in VHT20MHz +# Valid values are 0,1. If commented out, the default value is 0. +# 0=disable, 1=enable +gEnableTxBFin20MHz=1 + +#Enable/Disable SU Tx beamformer support. +gEnableTxSUBeamformer=1 + +#Enable Scan Results Aging based on timer +#Timer value is in seconds +#If Set to 0 it will not enable the feature +gScanAgingTime=30 + +#Enable Scan Results Aging based on number of scans +gScanResultAgeCount=1 + +#Enable Power saving mechanism Based on Android Framework +#If set to 0 Driver internally control the Power saving mechanism +#If set to 1 Android Framwrok control the Power saving mechanism +isAndroidPsEn=0 + +#Enable thermal mitigation +gThermalMitigationEnable=0 + +gEnableFastRoamInConcurrency=1 + +#Maxium Channel time in msec +gMaxMediumTime = 6000 + +# 802.11K support +gRrmEnable=1 +gRrmOperChanMax=8 +gRrmNonOperChanMax=8 +gRrmRandIntvl=100 + +#Scan offload +gEnableDirectedScanOffload=1 + +#FlexConnect Power Factor +#Default is set to 0 (disable) +gFlexConnectPowerFactor=0 + +#Disable split scan, the FW will take care of it +gNumChanCombinedConc=60 + +#Enable Power Save offload +gEnablePowerSaveOffload=2 + +#Enable firmware uart print +gEnablefwprint=0 + +#P2P Listen offload +gEnableP2pListenOffload=1 + +# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) +gVhtAmpduLenExponent=7 + +# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) +gVhtMpduLen=2 + +# Maximum number of wow filters required +#gMaxWoWFilters=22 + +# WOW Enable/Disable. +# 0 - Disable both magic pattern match and pattern byte match. +# 1 - Enable magic pattern match on all interfaces. +# 2 - Enable pattern byte match on all interfaces. +# 3 - Enable both magic patter and pattern byte match on all interfaces. +# Default value of gEnableWoW is 3. +# gEnableWoW=0 + +# Enable or Disable MCC Adaptive Scheduler at the FW +# 1=Enable (default), 0=Disable +gEnableMCCAdaptiveScheduler=1 + +#Enable or Disable p2p device address administered +isP2pDeviceAddrAdministrated=0 + +# Set Thermal Power limit +TxPower2g=10 +TxPower5g=10 + +# Remove Overlap channel restriction +gEnableOverLapCh=0 + +#Enable VHT on 2.4Ghz +gEnableVhtFor24GHzBand=1 + +#Enable or Disable 5G early beacon termination +gEnable5gEBT=1 + +#Maximum number of offload peers supported +# gMaxOffloadPeers=2 + +# controlling the following offload patterns +# through ini parameter. Default value is 1 +# to disable set it to zero. ssdp = 0 +# Setup multicast pattern for mDNS 224.0.0.251, +# SSDP 239.255.255.250 and LLMNR 224.0.0.252 +ssdp = 0 + +#Enable Memory Deep Sleep +gEnableMemDeepSleep=1 + +# Regulatory Setting; 0=STRICT; 1=CUSTOM +gRegulatoryChangeCountry=1 +# RA filtering rate limit param, the current value would not +# help if the lifetime in RA is less than 3*60=3min. Then +# we need to change it, though it is uncommon. +# gRAFilterEnable=0 +gRArateLimitInterval=600 + +# Maximum number of concurrent connections +gMaxConcurrentActiveSessions=3 + +# Disable/Enable GreenAP +# 0 to disable, 1 to enable, default: 1 +gEnableGreenAp=1 + +# Radar PRI multiplier +gDFSradarMappingPriMultiplier=4 + +gPNOScanSupport=1 + +#Enable/Disable LPASS support +# 0 to disable, 1 to enable +gEnableLpassSupport=0 + +# Whether userspace country code setting shld have priority +gCountryCodePriority=1 + +# Enable(1)/Disable(0) SIFS burst +gEnableSifsBurst=1 + +# Enable or Disable Multi-user MIMO +# 1=Enable (default), 0=Disable +gEnableMuBformee=1 + +# Enable/Disable channel avoidance for SAP in SCC scenario +# 0 - disable +# 1 - enable +gSapSccChanAvoidance=0 + +# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode +gIbssTxSpEndInactivityTime=10 + +# Enable support for TDLS +# 0 - disable +# 1 - enable +gEnableTDLSSupport=1 + +# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall +# initiate TDLS Discovery towards a peer whenever setup criteria (throughput +# and RSSI) is met and then will initiate teardown when teardown criteria +# (idle packet count and RSSI) is met. +# 0 - disable +# 1 - enable +gEnableTDLSImplicitTrigger=1 + +# Enable TDLS External Control. That is, user space application has to +# first configure a peer MAC in wlan driver towards which TDLS is desired. +# Device will establish TDLS only towards those configured peers whenever +# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS +# when teardown criteria (idle packet count and RSSI) is met. However, +# device will accept TDLS connection if it is initiated from any other peer, +# even if that peer is not configured. +# 0 - disable +# 1 - enable +# For TDLS External Control, Implicit Trigger must also be enabled. +gTDLSExternalControl=1 + +# Enable support for TDLS off-channel operation +# 0 - disable +# 1 - enable +# TDLS off-channel operation will be invoked when there is only one +# TDLS connection. +gEnableTDLSOffChannel=1 + +# Enable or Disable Random MAC (Spoofing) +# 1=Enable, 0=Disable (default) +gEnableMacAddrSpoof=0 + +################ Datapath feature set Begin ################ +# Bus bandwidth threshold values in terms of number of packets +gBusBandwidthHighThreshold=2000 +gBusBandwidthMediumThreshold=500 +gBusBandwidthLowThreshold=150 + +# Bus bandwidth compute timeout value in ms +gBusBandwidthComputeInterval=100 + +# VHT Tx/Rx MCS values +# Valid values are 0,1,2. If commented out, the default value is 0. +# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 +gVhtRxMCS=2 +gVhtTxMCS=2 + +# VHT Tx/Rx MCS values for 2x2 +# Valid values are 0,1,2. If commented out, the default value is 0. +# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 +gEnable2x2=1 +gVhtRxMCS2x2=2 +gVhtTxMCS2x2=2 + +#IPA config +gIPAConfig=0 +gIPADescSize=800 +gIPAPreFilterEnable=1 +gIPARMEnable=1 +gIPAIPv6Enable=1 + +IpaUcOffloadEnabled=0 +gIpaUcStaOffload=0 + +# Enable/Disable RX full reorder offload +gReorderOffloadSupported=1 + +# Enable CE classification +# 1 - enable(default) 0 - disable +gCEClassifyEnable=1 + +#Enable Rx thread +# 1 - enable 0 - disable(default) +gEnableRxThread=0 + +# Enable(Tx) fastpath for data traffic. +# 1 - enable(default) 0 - disable +gEnableFastPath=1 + +# This flag enables IP, TCP and UDP checksum offload +# 1 - enable(default) 0 - disable +gEnableIpTcpUdpChecksumOffload=1 + +# Enable NAPI +# 1 - enable(default) 0 - disable +gEnableNAPI=1 + +# Enable TCP Segmentation Offload +# 1 - enable(default) 0 - disable +TSOEnable=1 + +# Enable Large Recieve Offload +# 1 - enable(default) 0 - disable +LROEnable=1 +################ Datapath feature set End ################ + +END + +# Note: Configuration parser would not read anything past the END marker + |