wayne: wifi: Organize for wifi configs

Change-Id: I7babdea2c169c02bc2659054e3675bc7aa6f65a3
Signed-off-by: Isaac Chen <isaacchen@isaacchen.cn>

1 files changed, 0 insertions, 449 deletions

diff --git a/WCNSS_qcom_cfg.ini b/WCNSS_qcom_cfg.ini
deleted file mode 100755
index b411b5e..0000000
--- a/WCNSS_qcom_cfg.ini
+++ /dev/null
@@ -1,449 +0,0 @@
-# This file allows user to override the factory
-# defaults for the WLAN Driver
-
-# Enable IMPS or not
-gEnableImps=1
-
-# Enable BMPS or not
-gEnableBmps=1
-
-# Phy Mode (auto, b, g, n, etc)
-# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
-# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
-# 7 = 11b only 8 = 11ac only.
-gDot11Mode=0
-
-# Assigned MAC Addresses - This will be used until NV items are in place
-# Each byte of MAC address is represented in Hex format as XX
-Intf0MacAddress=000AF58989FF
-Intf1MacAddress=000AF58989FE
-Intf2MacAddress=000AF58989FD
-Intf3MacAddress=000AF58989FC
-
-# UAPSD service interval for VO,VI, BE, BK traffic
-InfraUapsdVoSrvIntv=0
-InfraUapsdViSrvIntv=0
-InfraUapsdBeSrvIntv=0
-InfraUapsdBkSrvIntv=0
-
-# Flag to allow STA send AddTspec even when ACM is Off
-gAddTSWhenACMIsOff=1
-
-# Flags to filter Mcast and Bcast RX packets.
-# Value 0: No filtering, 1: Filter all Multicast.
-# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
-McastBcastFilter=3
-
-#Flag to enable HostARPOffload feature or not
-hostArpOffload=1
-
-#Flag to enable HostNSOffload feature or not
-hostNSOffload=1
-
-# 802.11n Protection flag
-gEnableApProt=1
-
-#Enable OBSS protection
-gEnableApOBSSProt=1
-
-#Enable/Disable UAPSD for SoftAP
-gEnableApUapsd=1
-
-# Fixed Rate
-gFixedRate=0
-
-# Maximum Tx power
-# gTxPowerCap=30
-
-# Fragmentation Threshold
-# gFragmentationThreshold=2346
-
-# RTS threshold
-RTSThreshold=1048576
-
-# Intra-BSS forward
-gDisableIntraBssFwd=0
-
-# WMM Enable/Disable
-WmmIsEnabled=0
-
-# 802.11d support
-g11dSupportEnabled=0
-
-# 802.11h support
-g11hSupportEnabled=1
-
-# DFS Master Capability
-gEnableDFSMasterCap=1
-
-# ESE Support and fast transition
-EseEnabled=1
-
-ImplicitQosIsEnabled=0
-
-gNeighborScanTimerPeriod=200
-gNeighborLookupThreshold=76
-gNeighborScanChannelMinTime=20
-gNeighborScanChannelMaxTime=30
-gMaxNeighborReqTries=3
-
-# Legacy (non-ESE, non-802.11r) Fast Roaming Support
-# To enable, set FastRoamEnabled=1
-# To disable, set FastRoamEnabled=0
-FastRoamEnabled=1
-
-# Check if the AP to which we are roaming is better than current AP in
-# terms of RSSI.  Checking is disabled if set to Zero.Otherwise it will
-# use this value as to how better the RSSI of the new/roamable AP should
-# be for roaming
-RoamRssiDiff=3
-
-# To enable, set gRoamIntraBand=1 (Roaming within band)
-# To disable, set gRoamIntraBand=0 (Roaming across band)
-gRoamIntraBand=0
-
-#Short Guard Interval Enable/disable
-gShortGI20Mhz=1
-gShortGI40Mhz=1
-
-#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
-gAPAutoShutOff=0
-
-#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
-gWlanAutoShutdown = 0
-
-# Not used.
-gApAutoChannelSelection=0
-
-#Preferred band (both or 2.4 only or 5 only)
-BandCapability=0
-
-#Channel Bonding
-gChannelBondingMode5GHz=1
-
-#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
-#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
-#is idle for last 10 seconds.) For both active and power save clients.
-
-#Power save clients: DUT set TIM bit from 10th second onwards and till client
-#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.
-
-#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
-#success still we try on 11th second if not tries on 12th and so on till 15th
-#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
-#case DUT will detect client got removed in (10+5) seconds.
-#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
-
-#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
-#it is period where we send NULL frame.
-#gApLinkMonitorPeriod = 10
-#gGoLinkMonitorPeriod = 10
-
-#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame
-#are succeed to send or not. Hence total effective detection time is
-# (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) /
-# (gApLinkMonitorPeriod + gApKeepAlivePeriod)
-gGoKeepAlivePeriod = 20
-gApKeepAlivePeriod = 20
-
-#If set will start with active scan after driver load, otherwise will start with
-#passive scan to find out the domain
-gEnableBypass11d=1
-
-#If set to 0, will not scan DFS channels
-gEnableDFSChnlScan=1
-
-# Enable DFS channel roam
-# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
-gAllowDFSChannelRoam=1
-
-gVhtChannelWidth=2
-
-#Data Inactivity Timeout when in powersave (in ms)
-gDataInactivityTimeout=200
-
-# Set txchainmask and rxchainmask
-# These parameters are used only if gEnable2x2 is 0
-# Valid values are 1,2
-# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
-# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
-gSetTxChainmask1x1=1
-gSetRxChainmask1x1=1
-
-# Scan Timing Parameters
-# gPassiveMaxChannelTime=110
-# gPassiveMinChannelTime=60
-gActiveMaxChannelTime=40
-gActiveMinChannelTime=20
-
-#If set to 0, MCC is not allowed.
-gEnableMCCMode=1
-
-# MCC to SCC Switch mode:
-# 0-Disable
-# 1-Enable
-# 2-Force SCC if same band, with SAP restart
-# 3-Force SCC if same band, without SAP restart by sending (E)CSA
-# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
-#   without SAP restart by sending (E)CSA
-gWlanMccToSccSwitchMode = 0
-
-# 1=enable STBC; 0=disable STBC
-gEnableRXSTBC=1
-
-# 1=enable tx STBC; 0=disable
-gEnableTXSTBC=1
-
-# 1=enable rx LDPC; 0=disable
-gEnableRXLDPC=1
-
-#Enable/Disable Tx beamforming
-gTxBFEnable=1
-
-#Enable/Disable Tx beamformee in SAP mode
-gEnableTxBFeeSAP=1
-
-# Enable Tx beamforming in VHT20MHz
-# Valid values are 0,1. If commented out, the default value is 0.
-# 0=disable, 1=enable
-gEnableTxBFin20MHz=1
-
-#Enable/Disable SU Tx beamformer support.
-gEnableTxSUBeamformer=1
-
-#Enable thermal mitigation
-gThermalMitigationEnable=0
-
-gEnableFastRoamInConcurrency=1
-
-#Maxium Channel time in msec
-gMaxMediumTime = 6000
-
-# 802.11K support
-gRrmEnable=1
-
-#Enable Power Save offload
-gEnablePowerSaveOffload=2
-
-#Enable firmware uart print
-gEnablefwprint=0
-
-# Firmware log mode
-# Valid values are 0,1,2
-# 0 - Disable
-# 1 - WMI
-# 2 - DIAG
-gEnablefwlog=1
-
-# Maximum Receive AMPDU size (VHT only. Valid values:
-# 0->8k 1->16k 2->32k 3->64k 4->128k)
-gVhtAmpduLenExponent=7
-
-# Maximum MPDU length (VHT only. Valid values:
-# 0->3895 octets, 1->7991 octets, 2->11454 octets)
-gVhtMpduLen=2
-
-# Maximum number of wow filters required
-#gMaxWoWFilters=22
-
-# WOW Enable/Disable.
-# 0 - Disable both magic pattern match and pattern byte match.
-# 1 - Enable magic pattern match on all interfaces.
-# 2 - Enable pattern byte match on all interfaces.
-# 3 - Enable both magic pattern and pattern byte match on all interfaces.
-# Default value of gEnableWoW is 3.
-# gEnableWoW=0
-
-# Enable or Disable MCC Adaptive Scheduler at the FW
-# 1=Enable (default), 0=Disable
-gEnableMCCAdaptiveScheduler=1
-
-#Enable or Disable p2p device address administered
-isP2pDeviceAddrAdministrated=0
-
-# Set Thermal Power limit
-TxPower2g=10
-TxPower5g=10
-
-# Remove Overlap channel restriction
-gEnableOverLapCh=0
-
-#Enable VHT on 2.4Ghz
-gEnableVhtFor24GHzBand=1
-
-#Maximum number of offload peers supported
-# gMaxOffloadPeers=2
-
-# controlling the following offload patterns
-# through ini parameter. Default value is 1
-# to disable set it to zero. ssdp = 0
-# Setup multicast pattern for mDNS 224.0.0.251,
-# SSDP 239.255.255.250 and LLMNR 224.0.0.252
-ssdp=0
-
-#Enable Memory Deep Sleep
-gEnableMemDeepSleep=1
-
-# Regulatory Setting; 0=STRICT; 1=CUSTOM
-gRegulatoryChangeCountry=1
-
-# RA filtering rate limit param, the current value would not
-# help if the lifetime in RA is less than 3*60=3min. Then
-# we need to change it, though it is uncommon.
-# gRAFilterEnable=0
-gRArateLimitInterval=600
-
-# Maximum number of concurrent connections
-gMaxConcurrentActiveSessions=3
-
-# Disable/Enable GreenAP
-# 0 to disable, 1 to enable, default: 1
-gEnableGreenAp=0
-
-# Radar PRI multiplier
-gDFSradarMappingPriMultiplier=4
-
-gPNOScanSupport=1
-
-#Enable/Disable LPASS support
-# 0 to disable, 1 to enable
-gEnableLpassSupport=1
-
-# Whether userspace country code setting shld have priority
-gCountryCodePriority=1
-
-# Enable(1)/Disable(0) SIFS burst
-gEnableSifsBurst=1
-
-# Enable or Disable Multi-user MIMO
-# 1=Enable (default), 0=Disable
-gEnableMuBformee=1
-
-# Enable/Disable channel avoidance for SAP in SCC scenario
-# 0 - disable
-# 1 - enable
-gSapSccChanAvoidance=0
-
-# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
-gIbssTxSpEndInactivityTime=10
-
-# Enable support for TDLS
-#  0 - disable
-#  1 - enable
-gEnableTDLSSupport=1
-
-# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
-# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
-# and RSSI) is met and then will initiate teardown when teardown criteria
-# (idle packet count and RSSI) is met.
-#  0 - disable
-#  1 - enable
-gEnableTDLSImplicitTrigger=1
-
-# Enable TDLS External Control. That is, user space application has to
-# first configure a peer MAC in wlan driver towards which TDLS is desired.
-# Device will establish TDLS only towards those configured peers whenever
-# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
-# when teardown criteria (idle packet count and RSSI) is met. However,
-# device will accept TDLS connection if it is initiated from any other peer,
-# even if that peer is not configured.
-#  0 - disable
-#  1 - enable
-# For TDLS External Control, Implicit Trigger must also be enabled.
-gTDLSExternalControl=1
-
-# Enable support for TDLS off-channel operation
-#  0 - disable
-#  1 - enable
-# TDLS off-channel operation will be invoked when there is only one
-# TDLS connection.
-gEnableTDLSOffChannel=1
-
-# Enable or Disable Random MAC (Spoofing)
-# 1=Enable, 0=Disable (default)
-gEnableMacAddrSpoof=1
-
-################ Datapath feature set Begin ################
-# Bus bandwidth threshold values in terms of number of packets
-gBusBandwidthHighThreshold=2000
-gBusBandwidthMediumThreshold=500
-gBusBandwidthLowThreshold=150
-
-# Bus bandwidth compute timeout value in ms
-gBusBandwidthComputeInterval=100
-
-# VHT Tx/Rx MCS values
-# Valid values are 0,1,2. If commented out, the default value is 0.
-# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
-gVhtRxMCS=2
-gVhtTxMCS=2
-
-# VHT Tx/Rx MCS values for 2x2
-# Valid values are 0,1,2. If commented out, the default value is 0.
-# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
-gEnable2x2=1
-gVhtRxMCS2x2=2
-gVhtTxMCS2x2=2
-
-#IPA config is a bit mask and following are the configurations.
-#bit0 IPA Enable
-#bit1 IPA PRE Filter enable
-#bit2 IPv6 enable
-#bit3 IPA Resource Manager (RM) enable
-#bit4 IPA Clock scaling enable
-#bit5 IPA uC ENABLE
-#bit6 IPA uC STA ENABLE
-#bit8 IPA Real Time Debugging
-gIPAConfig=0x7d
-gIPADescSize=800
-
-# Enable/Disable RX full reorder offload
-gReorderOffloadSupported=1
-
-# Enable CE classification
-# 1 - enable(default)  0 - disable
-gCEClassifyEnable=1
-
-# Enable Rx handling options
-# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
-rx_mode=4
-
-# Enable(Tx) fastpath for data traffic.
-# 1 - enable(default)  0 - disable
-gEnableFastPath=1
-
-# This flag enables IP, TCP and UDP checksum offload
-# 1 - enable(default)  0 - disable
-gEnableIpTcpUdpChecksumOffload=1
-
-# Enable TCP Segmentation Offload
-# 1 - enable  0 - disable
-TSOEnable=1
-
-# Enable Large Recieve Offload
-# 1 - enable(default)  0 - disable
-LROEnable=1
-
-# Enable HT MPDU Density
-# 4 for 2 micro sec
-ght_mpdu_density=4
-
-# Enable flow steering to enable multiple CEs for Rx flows.
-# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
-# Parallel Rx paths.
-# 1 - enable 0 - disable(default)
-gEnableFlowSteering=1
-
-################ Datapath feature set End ################
-
-################ NAN feature set start ###################
-
-# Enable NAN discovery (NAN 1.0)
-# 1 - enable  0 - disable(default)
-gEnableNanSupport=1
-################ NAN feature set end #####################
-
-END
-
-# Note: Configuration parser would not read anything past the END marker
-