Initial changes to bringup msmfalcon_64 target.

Change-Id: If686e44247fe1c98c015f26a80fc64debfd521a0

1 files changed, 612 insertions, 0 deletions

diff --git a/WCNSS_qcom_cfg.ini b/WCNSS_qcom_cfg.ini
new file mode 100644
index 0000000..7f49593
--- /dev/null
+++ b/WCNSS_qcom_cfg.ini
@@ -0,0 +1,612 @@
+# This file allows user to override the factory
+
+# defaults for the WLAN Driver
+
+
+# Enable IMPS or not
+gEnableImps=1
+
+# Enable/Disable Idle Scan
+
+gEnableIdleScan=0
+
+
+# Increase sleep duration (seconds) during IMPS
+# 0 implies no periodic wake up from IMPS. Periodic wakeup is
+# unnecessary if Idle Scan is disabled.
+gImpsModSleepTime=0
+
+
+# Enable BMPS or not
+gEnableBmps=1
+
+# Enable suspend or not
+
+# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
+
+gEnableSuspend=3
+
+
+# Phy Mode (auto, b, g, n, etc)
+# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
+# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
+# 7 = 11b only 8 = 11ac only.
+gDot11Mode=0
+
+
+# CSR Roaming Enable(1) Disable(0)
+
+gRoamingTime=0
+
+
+# Assigned MAC Addresses - This will be used until NV items are in place
+
+# Each byte of MAC address is represented in Hex format as XX
+
+Intf0MacAddress=000AF58989FF
+Intf1MacAddress=000AF58989FE
+Intf2MacAddress=000AF58989FD
+
+Intf3MacAddress=000AF58989FC
+
+
+# UAPSD service interval for VO,VI, BE, BK traffic
+
+InfraUapsdVoSrvIntv=0
+
+InfraUapsdViSrvIntv=0
+
+InfraUapsdBeSrvIntv=0
+
+InfraUapsdBkSrvIntv=0
+
+# Flag to allow STA send AddTspec even when ACM is Off
+gAddTSWhenACMIsOff=1
+
+# Make 1x1 the default antenna configuration
+
+gNumRxAnt=1
+
+
+# Beacon filtering frequency (unit in beacon intervals)
+
+gNthBeaconFilter=50
+
+
+# Enable WAPI or not
+
+# WAPIIsEnabled=0
+
+
+# Flags to filter Mcast abd Bcast RX packets.
+
+# Value 0: No filtering, 1: Filter all Multicast.
+
+# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
+
+McastBcastFilter=3
+
+
+#Flag to enable HostARPOffload feature or not
+
+hostArpOffload=1
+
+#Flag to enable HostNSOffload feature or not
+
+hostNSOffload=1
+
+#SoftAP Related Parameters
+
+# AP MAc addr
+
+gAPMacAddr=000AF589dcab
+
+
+# 802.11n Protection flag
+
+gEnableApProt=1
+
+
+#Enable OBSS protection
+
+gEnableApOBSSProt=1
+
+
+#Enable/Disable UAPSD for SoftAP
+
+gEnableApUapsd=1
+
+
+# Fixed Rate
+
+gFixedRate=0
+
+
+# Maximum Tx power
+
+# gTxPowerCap=30
+
+
+# Fragmentation Threshold
+
+# gFragmentationThreshold=2346
+
+
+# RTS threshold
+
+RTSThreshold=1048576
+
+
+# Intra-BSS forward
+
+gDisableIntraBssFwd=0
+
+
+# WMM Enable/Disable
+
+WmmIsEnabled=0
+
+
+# 802.11d support
+
+g11dSupportEnabled=0
+
+# 802.11h support
+
+g11hSupportEnabled=1
+
+# DFS Master Capability
+gEnableDFSMasterCap=1
+
+# ESE Support and fast transition
+EseEnabled=1
+ImplicitQosIsEnabled=0
+gNeighborScanTimerPeriod=200
+
+gNeighborLookupThreshold=76
+gNeighborReassocThreshold=81
+
+gNeighborScanChannelMinTime=20
+gNeighborScanChannelMaxTime=30
+gMaxNeighborReqTries=3
+
+# Legacy (non-ESE, non-802.11r) Fast Roaming Support
+# To enable, set FastRoamEnabled=1
+# To disable, set FastRoamEnabled=0
+FastRoamEnabled=1
+
+#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
+#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
+#the RSSI of the new/roamable AP should be for roaming
+RoamRssiDiff=3
+
+# If the RSSI of any available candidate is better than currently associated
+# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
+# registering for reassoc threshold).
+# NOTE: Value of 0 means that we would register for reassoc threshold.
+gImmediateRoamRssiDiff=10
+
+# To enable, set gRoamIntraBand=1 (Roaming within band)
+# To disable, set gRoamIntraBand=0 (Roaming across band)
+gRoamIntraBand=0
+
+#Short Guard Interval Enable/disable
+
+gShortGI20Mhz=1
+
+gShortGI40Mhz=1
+
+
+#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
+
+gAPAutoShutOff=0
+
+#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
+gWlanAutoShutdown = 0
+
+# Not used.
+gApAutoChannelSelection=0
+
+
+# Listen Energy Detect Mode Configuration
+
+# Valid values 0-128
+
+# 128 means disable Energy Detect feature
+
+# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
+
+# 10-128 are reserved.
+
+# The EDET threshold mapping is as follows in 3dB step:
+
+# 0 = -60 dBm
+
+# 1 = -63 dBm
+
+# 2 = -66 dBm
+
+# ...
+
+# 7 = -81 dBm
+
+# 8 = -84 dBm
+
+# 9 = -87 dBm
+
+# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
+
+#
+
+#  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.
+
+#
+
+gEnablePhyAgcListenMode=128
+
+
+#Preferred band (both or 2.4 only or 5 only)
+
+BandCapability=0
+
+
+#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
+
+enableBeaconEarlyTermination=0
+
+beaconEarlyTerminationWakeInterval=3
+
+
+#Channel Bonding
+gChannelBondingMode5GHz=1
+
+
+#Enable Keep alive with non-zero period value
+
+gStaKeepAlivePeriod = 30
+
+#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
+#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
+#For both active and power save clients.
+
+#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
+#If doesn't honor for 5 seconds then DUT remove client.
+
+#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
+#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
+#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
+
+#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
+#where we send NULL frame.
+
+#gApLinkMonitorPeriod = 10
+
+#gGoLinkMonitorPeriod = 10
+
+#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
+#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
+
+
+gGoKeepAlivePeriod = 20
+
+gApKeepAlivePeriod = 20
+
+
+#If set will start with active scan after driver load, otherwise will start with
+
+#passive scan to find out the domain
+
+gEnableBypass11d=1
+
+
+#If set to 0, will not scan DFS channels
+
+gEnableDFSChnlScan=1
+
+# Enable DFS channel roam
+# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
+gAllowDFSChannelRoam=1
+
+gVhtChannelWidth=2
+
+# Enable Automatic Tx Power control
+
+gEnableAutomaticTxPowerControl=1
+
+# 0 for OLPC 1 for CLPC and SCPC
+gEnableCloseLoop=1
+
+#Data Inactivity Timeout when in powersave (in ms)
+gDataInactivityTimeout=200
+
+# Set txchainmask and rxchainmask
+# These parameters are used only if gEnable2x2 is 0
+# Valid values are 1,2
+# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
+# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
+gSetTxChainmask1x1=1
+gSetRxChainmask1x1=1
+
+# Scan Timing Parameters
+# gPassiveMaxChannelTime=110
+# gPassiveMinChannelTime=60
+gActiveMaxChannelTime=40
+gActiveMinChannelTime=20
+
+#If set to 0, MCC is not allowed.
+gEnableMCCMode=1
+
+# MCC to SCC Switch mode:
+# 0-Disable
+# 1-Enable
+# 2-Force SCC if same band, with SAP restart
+# 3-Force SCC if same band, without SAP restart by sending (E)CSA
+# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
+#   without SAP restart by sending (E)CSA
+gWlanMccToSccSwitchMode = 0
+
+# 1=enable STBC; 0=disable STBC
+gEnableRXSTBC=1
+
+# 1=enable tx STBC; 0=disable
+gEnableTXSTBC=1
+
+# 1=enable rx LDPC; 0=disable
+gEnableRXLDPC=0
+
+#Enable/Disable Tx beamforming
+gTxBFEnable=1
+
+#Enable/Disable Tx beamformee in SAP mode
+gEnableTxBFeeSAP=1
+
+# Enable Tx beamforming in VHT20MHz
+# Valid values are 0,1. If commented out, the default value is 0.
+# 0=disable, 1=enable
+gEnableTxBFin20MHz=1
+
+#Enable/Disable SU Tx beamformer support.
+gEnableTxSUBeamformer=1
+
+#Enable Scan Results Aging based on timer
+#Timer value is in seconds
+#If Set to 0 it will not enable the feature
+gScanAgingTime=30
+
+#Enable Scan Results Aging based on number of scans
+gScanResultAgeCount=1
+
+#Enable Power saving mechanism Based on Android Framework
+#If set to 0 Driver internally control the Power saving mechanism
+#If set to 1 Android Framwrok control the Power saving mechanism
+isAndroidPsEn=0
+
+#Enable thermal mitigation
+gThermalMitigationEnable=0
+
+gEnableFastRoamInConcurrency=1
+
+#Maxium Channel time in msec
+gMaxMediumTime = 6000
+
+# 802.11K support
+gRrmEnable=1
+gRrmOperChanMax=8
+gRrmNonOperChanMax=8
+gRrmRandIntvl=100
+
+#Scan offload
+gEnableDirectedScanOffload=1
+
+#FlexConnect Power Factor
+#Default is set to 0 (disable)
+gFlexConnectPowerFactor=0
+
+#Disable split scan, the FW will take care of it
+gNumChanCombinedConc=60
+
+#Enable Power Save offload
+gEnablePowerSaveOffload=2
+
+#Enable firmware uart print
+gEnablefwprint=0
+
+#P2P Listen offload
+gEnableP2pListenOffload=1
+
+# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k)
+gVhtAmpduLenExponent=7
+
+# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets)
+gVhtMpduLen=2
+
+# Maximum number of wow filters required
+#gMaxWoWFilters=22
+
+# WOW Enable/Disable.
+# 0 - Disable both magic pattern match and pattern byte match.
+# 1 - Enable magic pattern match on all interfaces.
+# 2 - Enable pattern byte match on all interfaces.
+# 3 - Enable both magic patter and pattern byte match on all interfaces.
+# Default value of gEnableWoW is 3.
+# gEnableWoW=0
+
+# Enable or Disable MCC Adaptive Scheduler at the FW
+# 1=Enable (default), 0=Disable
+gEnableMCCAdaptiveScheduler=1
+
+#Enable or Disable p2p device address administered
+isP2pDeviceAddrAdministrated=0
+
+# Set Thermal Power limit
+TxPower2g=10
+TxPower5g=10
+
+# Remove Overlap channel restriction
+gEnableOverLapCh=0
+
+#Enable VHT on 2.4Ghz
+gEnableVhtFor24GHzBand=1
+
+#Enable or Disable 5G early beacon termination
+gEnable5gEBT=1
+
+#Maximum number of offload peers supported
+# gMaxOffloadPeers=2
+
+# controlling the following offload patterns
+# through ini parameter. Default value is 1
+# to disable set it to zero. ssdp = 0
+# Setup multicast pattern for mDNS 224.0.0.251,
+# SSDP 239.255.255.250 and LLMNR 224.0.0.252
+ssdp = 0
+
+#Enable Memory Deep Sleep
+gEnableMemDeepSleep=1
+
+# Regulatory Setting; 0=STRICT; 1=CUSTOM
+gRegulatoryChangeCountry=1
+# RA filtering rate limit param, the current value would not
+# help if the lifetime in RA is less than 3*60=3min. Then
+# we need to change it, though it is uncommon.
+# gRAFilterEnable=0
+gRArateLimitInterval=600
+
+# Maximum number of concurrent connections
+gMaxConcurrentActiveSessions=3
+
+# Disable/Enable GreenAP
+# 0 to disable, 1 to enable, default: 1
+gEnableGreenAp=1
+
+# Radar PRI multiplier
+gDFSradarMappingPriMultiplier=4
+
+gPNOScanSupport=1
+
+#Enable/Disable LPASS support
+# 0 to disable, 1 to enable
+gEnableLpassSupport=0
+
+# Whether userspace country code setting shld have priority
+gCountryCodePriority=1
+
+# Enable(1)/Disable(0) SIFS burst
+gEnableSifsBurst=1
+
+# Enable or Disable Multi-user MIMO
+# 1=Enable (default), 0=Disable
+gEnableMuBformee=1
+
+# Enable/Disable channel avoidance for SAP in SCC scenario
+# 0 - disable
+# 1 - enable
+gSapSccChanAvoidance=0
+
+# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
+gIbssTxSpEndInactivityTime=10
+
+# Enable support for TDLS
+#  0 - disable
+#  1 - enable
+gEnableTDLSSupport=1
+
+# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
+# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
+# and RSSI) is met and then will initiate teardown when teardown criteria
+# (idle packet count and RSSI) is met.
+#  0 - disable
+#  1 - enable
+gEnableTDLSImplicitTrigger=1
+
+# Enable TDLS External Control. That is, user space application has to
+# first configure a peer MAC in wlan driver towards which TDLS is desired.
+# Device will establish TDLS only towards those configured peers whenever
+# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
+# when teardown criteria (idle packet count and RSSI) is met. However,
+# device will accept TDLS connection if it is initiated from any other peer,
+# even if that peer is not configured.
+#  0 - disable
+#  1 - enable
+# For TDLS External Control, Implicit Trigger must also be enabled.
+gTDLSExternalControl=1
+
+# Enable support for TDLS off-channel operation
+#  0 - disable
+#  1 - enable
+# TDLS off-channel operation will be invoked when there is only one
+# TDLS connection.
+gEnableTDLSOffChannel=1
+
+# Enable or Disable Random MAC (Spoofing)
+# 1=Enable, 0=Disable (default)
+gEnableMacAddrSpoof=0
+
+################ Datapath feature set Begin ################
+# Bus bandwidth threshold values in terms of number of packets
+gBusBandwidthHighThreshold=2000
+gBusBandwidthMediumThreshold=500
+gBusBandwidthLowThreshold=150
+
+# Bus bandwidth compute timeout value in ms
+gBusBandwidthComputeInterval=100
+
+# VHT Tx/Rx MCS values
+# Valid values are 0,1,2. If commented out, the default value is 0.
+# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
+gVhtRxMCS=2
+gVhtTxMCS=2
+
+# VHT Tx/Rx MCS values for 2x2
+# Valid values are 0,1,2. If commented out, the default value is 0.
+# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
+gEnable2x2=1
+gVhtRxMCS2x2=2
+gVhtTxMCS2x2=2
+
+#IPA config
+gIPAConfig=0
+gIPADescSize=800
+gIPAPreFilterEnable=1
+gIPARMEnable=1
+gIPAIPv6Enable=1
+
+IpaUcOffloadEnabled=0
+gIpaUcStaOffload=0
+
+# Enable/Disable RX full reorder offload
+gReorderOffloadSupported=1
+
+# Enable CE classification
+# 1 - enable(default)  0 - disable
+gCEClassifyEnable=1
+
+#Enable Rx thread
+# 1 - enable  0 - disable(default)
+gEnableRxThread=0
+
+# Enable(Tx) fastpath for data traffic.
+# 1 - enable(default)  0 - disable
+gEnableFastPath=1
+
+# This flag enables IP, TCP and UDP checksum offload
+# 1 - enable(default)  0 - disable
+gEnableIpTcpUdpChecksumOffload=1
+
+# Enable NAPI
+# 1 - enable(default)  0 - disable
+gEnableNAPI=1
+
+# Enable TCP Segmentation Offload
+# 1 - enable(default)  0 - disable
+TSOEnable=1
+
+# Enable Large Recieve Offload
+# 1 - enable(default)  0 - disable
+LROEnable=1
+################ Datapath feature set End ################
+
+END
+
+# Note: Configuration parser would not read anything past the END marker
+