diff options
Diffstat (limited to 'rootdir/system/etc/firmware')
-rw-r--r-- | rootdir/system/etc/firmware/wlan/prima/WCNSS_cfg.dat | bin | 0 -> 10746 bytes | |||
-rw-r--r-- | rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini | 371 | ||||
-rw-r--r-- | rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin | bin | 0 -> 29816 bytes |
3 files changed, 371 insertions, 0 deletions
diff --git a/rootdir/system/etc/firmware/wlan/prima/WCNSS_cfg.dat b/rootdir/system/etc/firmware/wlan/prima/WCNSS_cfg.dat Binary files differnew file mode 100644 index 0000000..5685e79 --- /dev/null +++ b/rootdir/system/etc/firmware/wlan/prima/WCNSS_cfg.dat diff --git a/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini b/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini new file mode 100644 index 0000000..9778686 --- /dev/null +++ b/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini @@ -0,0 +1,371 @@ +# This file allows user to override the factory + +# defaults for the WLAN Driver + + +# Enable IMPS or not +gEnableImps=1 + +# Enable/Disable Idle Scan + +gEnableIdleScan=0 + + +# Increase sleep duration (seconds) during IMPS +# 0 implies no periodic wake up from IMPS. Periodic wakeup is +# unnecessary if Idle Scan is disabled. +gImpsModSleepTime=0 + + +# Enable BMPS or not +gEnableBmps=1 + +# Enable suspend or not + +# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter + +gEnableSuspend=3 + + +# Phy Mode (auto, b, g, n, etc) +# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac +gDot11Mode=0 + + +# CSR Roaming Enable(1) Disable(0) + +gRoamingTime=0 + + +# Assigned MAC Addresses - This will be used until NV items are in place + +# Each byte of MAC address is represented in Hex format as XX + +Intf0MacAddress=000AF58989FF +Intf1MacAddress=000AF58989FE +Intf2MacAddress=000AF58989FD + +Intf3MacAddress=000AF58989FC + + +# UAPSD service interval for VO,VI, BE, BK traffic + +InfraUapsdVoSrvIntv=0 + +InfraUapsdViSrvIntv=0 + +InfraUapsdBeSrvIntv=0 + +InfraUapsdBkSrvIntv=0 + +# Flag to allow STA send AddTspec even when ACM is Off +gAddTSWhenACMIsOff=1 + +# Make 1x1 the default antenna configuration + +gNumRxAnt=1 + + +# Beacon filtering frequency (unit in beacon intervals) + +gNthBeaconFilter=50 + + +# Enable WAPI or not + +# WAPIIsEnabled=0 + + +# Flags to filter Mcast abd Bcast RX packets. + +# Value 0: No filtering, 1: Filter all Multicast. + +# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast + +McastBcastFilter=3 + + +#Flag to enable HostARPOffload feature or not + +hostArpOffload=1 + + +#SoftAP Related Parameters + +# AP MAc addr + +gAPMacAddr=000AF589dcab + + +# 802.11n Protection flag + +gEnableApProt=1 + + +#Enable OBSS protection + +gEnableApOBSSProt=1 + + +#Enable/Disable UAPSD for SoftAP + +gEnableApUapsd=0 + + +# Fixed Rate + +gFixedRate=0 + + +# Maximum Tx power + +# gTxPowerCap=30 + + +# Fragmentation Threshold + +# gFragmentationThreshold=2346 + + +# RTS threshold + +RTSThreshold=2347 + + +# Intra-BSS forward + +gDisableIntraBssFwd=0 + + +# WMM Enable/Disable + +WmmIsEnabled=0 + + +# 802.11d support + +g11dSupportEnabled=1 + +# CCX Support and fast transition +CcxEnabled=0 +FastTransitionEnabled=1 +ImplicitQosIsEnabled=0 +gNeighborScanTimerPeriod=200 + +gNeighborLookupThreshold=78 + +gNeighborScanChannelMinTime=20 +gNeighborScanChannelMaxTime=30 + +# Legacy (non-CCX, non-802.11r) Fast Roaming Support +# To enable, set FastRoamEnabled=1 +# To disable, set FastRoamEnabled=0 +FastRoamEnabled=1 + +#Check if the AP to which we are roaming is better than current AP in terms of RSSI. +#Checking is disabled if set to Zero.Otherwise it will use this value as to how better +#the RSSI of the new/roamable AP should be for roaming +RoamRssiDiff=5 + +# SAP Country code + +# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. + +# Example + +# US Indoor, USI + +# Korea Outdoor, KRO + +# Japan without optional byte, JP + +# France without optional byte, FR + +#gAPCntryCode=USI + + +#Short Guard Interval Enable/disable + +gShortGI20Mhz=1 + +gShortGI40Mhz=1 + + +#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled + +gAPAutoShutOff=0 + + +# SAP auto channel selection configuration + +# 0 = disable auto channel selection + +# 1 = enable auto channel selection, channel provided by supplicant will be ignored + +gApAutoChannelSelection=0 + + +# Listen Energy Detect Mode Configuration + +# Valid values 0-128 + +# 128 means disable Energy Detect feature + +# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. + +# 10-128 are reserved. + +# The EDET threshold mapping is as follows in 3dB step: + +# 0 = -60 dBm + +# 1 = -63 dBm + +# 2 = -66 dBm + +# ... + +# 7 = -81 dBm + +# 8 = -84 dBm + +# 9 = -87 dBm + +# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: + +# + +# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. + +# + +gEnablePhyAgcListenMode=128 + + +#Preferred channel to start BT AMP AP mode (0 means, any channel) + +BtAmpPreferredChannel=0 + + +#Preferred band (both or 2.4 only or 5 only) + +BandCapability=0 + + +#Beacon Early Termination (1 = enable the BET feature, 0 = disable) + +enableBeaconEarlyTermination=1 + +beaconEarlyTerminationWakeInterval=11 + + +#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) + +gEnableBtAmp=0 + + +#SOFTAP Channel Range selection + +gAPChannelSelectStartChannel=1 + +gAPChannelSelectEndChannel=11 + + +#SOFTAP Channel Range selection Operating band + +# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND + +gAPChannelSelectOperatingBand=0 + + +#Channel Bonding +gChannelBondingMode5GHz=1 + + +#Enable Keep alive with non-zero period value + +gStaKeepAlivePeriod=30 + + +#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). +#For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) +#For both active and power save clients. + +#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. +#If doesn't honor for 5 seconds then Driver remove client. + +#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on +#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. +#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod).. + +#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period +#where we send NULL frame. + +#gApLinkMonitorPeriod = 10 + +#gGoLinkMonitorPeriod = 10 + +#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. +#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. +#gGoKeepAlivePeriod = 5 + +#gApKeepAlivePeriod = 5 +#If set will start with active scan after driver load, otherwise will start with + +#passive scan to find out the domain + +#gEnableBypass11d=1 + + +#If set to 0, will not scan DFS channels + +gEnableDFSChnlScan=1 + + +gVhtChannelWidth=2 +gEnableLogp=1 + + +# Enable Automatic Tx Power control + +gEnableAutomaticTxPowerControl=1 + +# 0 for OLPC 1 for CLPC and SCPC +gEnableCloseLoop=1 + +#Data Inactivity Timeout when in powersave (in ms) +gDataInactivityTimeout=200 + +# VHT Tx/Rx MCS values +# Valid values are 0,1,2. If commented out, the default value is 0. +# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 +gVhtRxMCS=2 +gVhtTxMCS=2 + +gEnableLpwrImgTransition=1 + +# Enable Tx beamforming +gTxBFEnable=1 + +# Enable Tx LDPC +#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT +gTxLdpcEnable=3 + +#FlexConnect Power Factor +#Default is set to 0 (disable) +gFlexConnectPowerFactor=0 + +# Valid values are 2048,4096,8192 and so on +# Please don't use values other than the ones mentioned above +gMaxMediumTime=4096 + +# 802.11K support +gRrmEnable=1 +gRrmOperChanMax=8 +gRrmNonOperChanMax=8 +gRrmRandIntvl=100 + +END + +# Note: Configuration parser would not read anything past the END marker + diff --git a/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin b/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin Binary files differnew file mode 100644 index 0000000..a8dd301 --- /dev/null +++ b/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin |