diff options
Diffstat (limited to 'pn54x/libnfc-nci.conf')
| -rw-r--r-- | pn54x/libnfc-nci.conf | 195 |
1 files changed, 195 insertions, 0 deletions
diff --git a/pn54x/libnfc-nci.conf b/pn54x/libnfc-nci.conf new file mode 100644 index 0000000..d5ddcd2 --- /dev/null +++ b/pn54x/libnfc-nci.conf @@ -0,0 +1,195 @@ +###################### Start of libnfc-brcm.conf ####################### + +############################################################################### +# Application options +APPL_TRACE_LEVEL=0xFF +PROTOCOL_TRACE_LEVEL=0xFFFFFFFF + +############################################################################### +# File used for NFA storage +NFA_STORAGE="/data/nfc" + +############################################################################### +# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC +NFC_WAKE_DELAY=20 + +############################################################################### +# LPTD mode configuration +# byte[0] is the length of the remaining bytes in this value +# if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled). +# byte[1] is the param id it should be set to B9. +# byte[2] is the length of the LPTD parameters +# byte[3] indicates if LPTD is enabled +# if set to 0, LPTD will be disabled (parameters will still be sent). +# byte[4-n] are the LPTD parameters. +# By default, LPTD is enabled and default settings are used. +# See nfc_hal_dm_cfg.c for defaults +LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00} + +############################################################################### +# Startup Configuration (100 bytes maximum) +# +# For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is +# for UICC1. The values are defined as: +# 0 : UICCx only supports ISO_DEP in low power mode. +# 2 : UICCx only supports Mifare in low power mode. +# 3 : UICCx supports both ISO_DEP and Mifare in low power mode. +# +# AA BB +NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:80:01:01} + +############################################################################### +# Configure the default Destination Gate used by HCI (the default is 4, which +# is the ETSI loopback gate. +NFA_HCI_DEFAULT_DEST_GATE=0xF0 + +############################################################################### +# Configure the NFC Extras to open and use a static pipe. If the value is +# not set or set to 0, then the default is use a dynamic pipe based on a +# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value +# for each UICC (where F3="UICC0" and F4="UICC1") +#NFA_HCI_STATIC_PIPE_ID_F3=0x70 +#NFA_HCI_STATIC_PIPE_ID_01=0x19 +NFA_HCI_STATIC_PIPE_ID_C0=0x19 + +############################################################################### +# When disconnecting from Oberthur secure element, perform a warm-reset of +# the secure element to deselect the applet. +# The default hex value of the command is 0x3. If this variable is undefined, +# then this feature is not used. +OBERTHUR_WARM_RESET_COMMAND=0x03 + +############################################################################### +# Force UICC to only listen to the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F +UICC_LISTEN_TECH_MASK=0x07 + +############################################################################### +# Force HOST listen feature enable or disable. +# 0: Disable +# 1: Enable +HOST_LISTEN_ENABLE=0x01 + +############################################################################### +# Enabling/Disabling Forward functionality +# Disable 0x00 +# Enable 0x01 +NXP_FWD_FUNCTIONALITY_ENABLE=0x01 + +############################################################################### +# Allow UICC to be powered off if there is no traffic. +# Timeout is in ms. If set to 0, then UICC will not be powered off. +#UICC_IDLE_TIMEOUT=30000 +UICC_IDLE_TIMEOUT=0 + +############################################################################### +# AID for Empty Select command +# If specified, this AID will be substituted when an Empty SELECT command is +# detected. The first byte is the length of the AID. Maximum length is 16. +AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00} + +############################################################################### +# When screen is turned off, specify the desired power state of the controller. +# 0: power-off-sleep state; DEFAULT +# 1: full-power state +# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used) +SCREEN_OFF_POWER_STATE=1 + +############################################################################### +# Firmware patch file +# If the value is not set then patch download is disabled. +FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd" + +############################################################################### +# Firmware pre-patch file (sent before the above patch file) +# If the value is not set then pre-patch is not used. +FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd" + +############################################################################### +# Insert a delay in microseconds per byte after a write to NFCC. +# after writing a block of data to the NFCC, delay this an amopunt of time before +# writing next block of data. the delay is calculated as below +# NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds +# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write +NFC_WRITE_DELAY=20 + +############################################################################### +# Force tag polling for the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | +# NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 | +# NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO | +# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE. +# +# Notable bits: +# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ +# NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */ +# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ +# NFA_TECHNOLOGY_MASK_ISO15693 0x08 /* Proprietary Technology */ +# NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */ +# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */ +# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */ +POLLING_TECH_MASK=0xEF + +############################################################################### +# Force P2P to only listen for the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F | +# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE +# +# Notable bits: +# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ +# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ +# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */ +# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */ +P2P_LISTEN_TECH_MASK=0xC5 + +PRESERVE_STORAGE=0x01 + +############################################################################### +# Override the stack default for NFA_EE_MAX_EE_SUPPORTED set in nfc_target.h. +# The value is set to 3 by default as it assumes we will discover 0xF2, +# 0xF3, and 0xF4. If a platform will exclude and SE, this value can be reduced +# so that the stack will not wait any longer than necessary. + +# Maximum EE supported number +# NXP PN547C2 0x02 +# NXP PN65T 0x03 +# NXP PN548C2 0x02 +# NXP PN66T 0x03 +NFA_MAX_EE_SUPPORTED=0x02 + +############################################################################### +# NCI Hal Module name +NCI_HAL_MODULE="nfc_nci" + +############################################################################### +# AID_MATCHING constants +# AID_MATCHING_EXACT_ONLY 0x00 +# AID_MATCHING_EXACT_OR_PREFIX 0x01 +# AID_MATCHING_PREFIX_ONLY 0x02 +AID_MATCHING_MODE=0x01 + +############################################################################### +# Default Secure Element route id +DEFAULT_OFFHOST_ROUTE=0x02 + +############################################################################### +# Vendor Specific Proprietary Protocol & Discovery Configuration +# Set to 0xFF if unsupported +# byte[0] NCI_PROTOCOL_18092_ACTIVE +# byte[1] NCI_PROTOCOL_B_PRIME +# byte[2] NCI_PROTOCOL_DUAL +# byte[3] NCI_PROTOCOL_15693 +# byte[4] NCI_PROTOCOL_KOVIO +# byte[5] NCI_PROTOCOL_MIFARE +# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO +# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME +# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME +NFA_PROPRIETARY_CFG={05:FF:FF:06:81:80:77:FF:FF} + +############################################################################### +# Bail out mode +# If set to 1, NFCC is using bail out mode for either Type A or Type B poll. +NFA_POLL_BAIL_OUT_MODE=0x01 |