diff options
Diffstat (limited to 'pn54x/libnfc-brcm_NCI2_0.conf')
| -rw-r--r-- | pn54x/libnfc-brcm_NCI2_0.conf | 407 |
1 files changed, 0 insertions, 407 deletions
diff --git a/pn54x/libnfc-brcm_NCI2_0.conf b/pn54x/libnfc-brcm_NCI2_0.conf deleted file mode 100644 index a4d3290..0000000 --- a/pn54x/libnfc-brcm_NCI2_0.conf +++ /dev/null @@ -1,407 +0,0 @@ -###################### Start of libnfc-brcm.conf ####################### - -############################################################################### -# Application options -APPL_TRACE_LEVEL=0xFF -PROTOCOL_TRACE_LEVEL=0xFFFFFFFF - -############################################################################### -# performance measurement -# Change this setting to control how often USERIAL log the performance (throughput) -# data on read/write/poll -# defailt is to log performance dara for every 100 read or write -#REPORT_PERFORMANCE_MEASURE=100 - -############################################################################### -# File used for NFA storage -NFA_STORAGE="/data/nfc" - -############################################################################### -# Snooze Mode Settings -# -# By default snooze mode is enabled. Set SNOOZE_MODE_CFG byte[0] to 0 -# to disable. -# -# If SNOOZE_MODE_CFG is not provided, the default settings are used: -# They are as follows: -# 8 Sleep Mode (0=Disabled 1=UART 8=SPI/I2C) -# 0 Idle Threshold Host -# 0 Idle Threshold HC -# 0 NFC Wake active mode (0=ActiveLow 1=ActiveHigh) -# 1 Host Wake active mode (0=ActiveLow 1=ActiveHigh) -# -#SNOOZE_MODE_CFG={08:00:00:00:01} - -############################################################################### -# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC -#NFC_WAKE_DELAY=20 - -############################################################################### -# Various Delay settings (in ms) used in USERIAL -# POWER_ON_DELAY -# Delay after turning on chip, before writing to transport (default 300) -# PRE_POWER_OFF_DELAY -# Delay after deasserting NFC-Wake before turn off chip (default 0) -# POST_POWER_OFF_DELAY -# Delay after turning off chip, before USERIAL_close returns (default 0) -# -#POWER_ON_DELAY=300 -#PRE_POWER_OFF_DELAY=0 -#POST_POWER_OFF_DELAY=0 - -############################################################################### -# Maximum time (ms) to wait for RESET NTF after setting REG_PU to high -# The default is 1000. -#NFCC_ENABLE_TIMEOUT=0 - -############################################################################### -# LPTD mode configuration -# byte[0] is the length of the remaining bytes in this value -# if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled). -# byte[1] is the param id it should be set to B9. -# byte[2] is the length of the LPTD parameters -# byte[3] indicates if LPTD is enabled -# if set to 0, LPTD will be disabled (parameters will still be sent). -# byte[4-n] are the LPTD parameters. -# By default, LPTD is enabled and default settings are used. -# See nfc_hal_dm_cfg.c for defaults -#LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00} - -############################################################################### -# Startup Configuration (100 bytes maximum) -# -# For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is -# for UICC1. The values are defined as: -# 0 : UICCx only supports ISO_DEP in low power mode. -# 2 : UICCx only supports Mifare in low power mode. -# 3 : UICCx supports both ISO_DEP and Mifare in low power mode. -# -# AA BB -#NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:80:01:01} - -############################################################################### -# Startup Vendor Specific Configuration (100 bytes maximum); -# byte[0] TLV total len = 0x5 -# byte[1] NCI_MTS_CMD|NCI_GID_PROP = 0x2f -# byte[2] NCI_MSG_FRAME_LOG = 0x9 -# byte[3] 2 -# byte[4] 0=turn off RF frame logging; 1=turn on -# byte[5] 0=turn off SWP frame logging; 1=turn on -# NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01} - -############################################################################### -# Antenna Configuration - This data is used when setting 0xC8 config item -# at startup (before discovery is started). If not used, no value is sent. -# -# The settings for this value are documented here: -# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/ -# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx -# This document is maintained by Paul Forshaw. -# -# The values marked as ?? should be tweaked per antenna or customer/app: -# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04} -# array[0] = 0x20 is length of the payload from array[1] to the end -# array[1] = 0xC8 is PREINIT_DSP_CFG -#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04} - -############################################################################### -# Configure crystal frequency when internal LPO can't detect the frequency. -#XTAL_FREQUENCY=0 -############################################################################### -# Configure the default Destination Gate used by HCI (the default is 4, which -# is the ETSI loopback gate. -NFA_HCI_DEFAULT_DEST_GATE=0xF0 - -############################################################################### -# Configure the single default SE to use. The default is to use the first -# SE that is detected by the stack. This value might be used when the phone -# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use -# one of them (e.g. 0xF4). -#ACTIVE_SE=0xF3 - -############################################################################### -# Configure the default NfcA/IsoDep techology and protocol route. Can be -# either a secure element (e.g. 0xF4) or the host (0x00) -#DEFAULT_ISODEP_ROUTE=0x00 - -############################################################################### -# Configure the NFC Extras to open and use a static pipe. If the value is -# not set or set to 0, then the default is use a dynamic pipe based on a -# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value -# for each UICC (where F3="UICC0" and F4="UICC1") -#NFA_HCI_STATIC_PIPE_ID_F3=0x70 -#NFA_HCI_STATIC_PIPE_ID_01=0x19 -NFA_HCI_STATIC_PIPE_ID_C0=0x19 -############################################################################### -# When disconnecting from Oberthur secure element, perform a warm-reset of -# the secure element to deselect the applet. -# The default hex value of the command is 0x3. If this variable is undefined, -# then this feature is not used. -#OBERTHUR_WARM_RESET_COMMAND=0x03 - -############################################################################### -# Force UICC to only listen to the following technology(s). -# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. -# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F -UICC_LISTEN_TECH_MASK=0x07 - -############################################################################### -# Force HOST listen feature enable or disable. -# 0: Disable -# 1: Enable -HOST_LISTEN_ENABLE=0x01 - -############################################################################### -# Enabling/Disabling Forward functionality -# Disable 0x00 -# Enable 0x01 -NXP_FWD_FUNCTIONALITY_ENABLE=0x01 - -############################################################################### -# Allow UICC to be powered off if there is no traffic. -# Timeout is in ms. If set to 0, then UICC will not be powered off. -#UICC_IDLE_TIMEOUT=30000 -UICC_IDLE_TIMEOUT=0 - -############################################################################### -# AID for Empty Select command -# If specified, this AID will be substituted when an Empty SELECT command is -# detected. The first byte is the length of the AID. Maximum length is 16. -AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00} -############################################################################### -# Maximum Number of Credits to be allowed by the NFCC -# This value overrides what the NFCC specifices allowing the host to have -# the control to work-around transport limitations. If this value does -# not exist or is set to 0, the NFCC will provide the number of credits. -MAX_RF_DATA_CREDITS=1 - -############################################################################### -# This setting allows you to disable registering the T4t Virtual SE that causes -# the NFCC to send PPSE requests to the DH. -# The default setting is enabled (i.e. T4t Virtual SE is registered). -#REGISTER_VIRTUAL_SE=1 - -############################################################################### -# When screen is turned off, specify the desired power state of the controller. -# 0: power-off-sleep state; DEFAULT -# 1: full-power state -# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used) -SCREEN_OFF_POWER_STATE=1 - -############################################################################### -# Firmware patch file -# If the value is not set then patch download is disabled. -#FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd" - -############################################################################### -# Firmware pre-patch file (sent before the above patch file) -# If the value is not set then pre-patch is not used. -#FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd" - -############################################################################### -# Firmware patch format -# 1 = HCD -# 2 = NCD (default) -#NFA_CONFIG_FORMAT=2 - -############################################################################### -# SPD Debug mode -# If set to 1, any failure of downloading a patch will trigger a hard-stop -#SPD_DEBUG=0 - -############################################################################### -# SPD Max Retry Count -# The number of attempts to download a patch before giving up (defualt is 3). -# Note, this resets after a power-cycle. -#SPD_MAX_RETRY_COUNT=3 - -############################################################################### -# transport driver -# -# TRANSPORT_DRIVER=<driver> -# -# where <driver> can be, for example: -# "/dev/ttyS" (UART) -# "/dev/bcmi2cnfc" (I2C) -# "hwtun" (HW Tunnel) -# "/dev/bcmspinfc" (SPI) -# "/dev/btusb0" (BT USB) -#TRANSPORT_DRIVER="/dev/bcm2079x-i2c" - -############################################################################### -# power control driver -# Specify a kernel driver that support ioctl commands to control NFC_EN and -# NFC_WAKE gpio signals. -# -# POWER_CONTRL_DRIVER=<driver> -# where <driver> can be, for example: -# "/dev/nfcpower" -# "/dev/bcmi2cnfc" (I2C) -# "/dev/bcmspinfc" (SPI) -# i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal -#POWER_CONTROL_DRIVER="/dev/bcm2079x-i2c" - -############################################################################### -# I2C transport driver options -# Mako does not support 10-bit I2C addresses -# Revert to 7-bit address -#BCMI2CNFC_ADDRESS=0x77 - -############################################################################### -# I2C transport driver try to read multiple packets in read() if data is available -# remove the comment below to enable this feature -#READ_MULTIPLE_PACKETS=1 - -############################################################################### -# SPI transport driver options -#SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00} - -############################################################################### -# UART transport driver options -# -# PORT=1,2,3,... -# BAUD=115200, 19200, 9600, 4800, -# DATABITS=8, 7, 6, 5 -# PARITY="even" | "odd" | "none" -# STOPBITS="0" | "1" | "1.5" | "2" - -#UART_PORT=2 -#UART_BAUD=115200 -#UART_DATABITS=8 -#UART_PARITY="none" -#UART_STOPBITS="1" - -############################################################################### -# Insert a delay in microseconds per byte after a write to NFCC. -# after writing a block of data to the NFCC, delay this an amopunt of time before -# writing next block of data. the delay is calculated as below -# NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds -# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write -#NFC_WRITE_DELAY=20 - -############################################################################### -# Maximum Number of Credits to be allowed by the NFCC -# This value overrides what the NFCC specifices allowing the host to have -# the control to work-around transport limitations. If this value does -# not exist or is set to 0, the NFCC will provide the number of credits. -MAX_RF_DATA_CREDITS=1 - -############################################################################### -# Default poll duration (in ms) -# The defualt is 500ms if not set (see nfc_target.h) -#NFA_DM_DISC_DURATION_POLL=333 -############################################################################### -# Antenna Configuration - This data is used when setting 0xC8 config item -# at startup (before discovery is started). If not used, no value is sent. -# -# The settings for this value are documented here: -# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/ -# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx -# This document is maintained by Paul Forshaw. -# -# The values marked as ?? should be tweaked per antenna or customer/app: -# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04} -# array[0] = 0x20 is length of the payload from array[1] to the end -# array[1] = 0xC8 is PREINIT_DSP_CFG -#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04} - -############################################################################### -# Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1. -# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm -# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block -# 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate -# 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0 -# 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3 -# 5 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check -# command is sent waiting for rsp and ntf. -PRESENCE_CHECK_ALGORITHM=5 - -############################################################################### -# Force tag polling for the following technology(s). -# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. -# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | -# NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 | -# NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO | -#NFA_TECHNOLOGY_MASK_ACTIVE -# -# Notable bits: -# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ -# NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */ -# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ -# NFA_TECHNOLOGY_MASK_ISO15693 0x08 /* Proprietary Technology */ -# NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */ -# NFA_TECHNOLOGY_MASK_ACTIVE 0x40 /* NFC Technology Active */ -POLLING_TECH_MASK=0x6F - -############################################################################### -# Force P2P to only listen for the following technology(s). -# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. -# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F | -#NFA_TECHNOLOGY_MASK_ACTIVE -# -# Notable bits: -# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ -# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ -#NFA_TECHNOLOGY_MASK_ACTIVE 0x40 /* NFC Technology Active */ -P2P_LISTEN_TECH_MASK=0x45 - -PRESERVE_STORAGE=0x01 - -############################################################################### -# Override the stack default for NFA_EE_MAX_EE_SUPPORTED set in nfc_target.h. -# The value is set to 3 by default as it assumes we will discover 0xF2, -# 0xF3, and 0xF4. If a platform will exclude and SE, this value can be reduced -# so that the stack will not wait any longer than necessary. - -# Maximum EE supported number -# NXP PN547C2 0x02 -# NXP PN65T 0x03 -# NXP PN548C2 0x02 -# NXP PN66T 0x03 -NFA_MAX_EE_SUPPORTED=0x02 - -############################################################################### -# NCI Hal Module name -NCI_HAL_MODULE="nfc_nci" - -############################################################################## -# Deactivate notification wait time out in seconds used in ETSI Reader mode -# 0 - Infinite wait -#NFA_DM_DISC_NTF_TIMEOUT=0 - -############################################################################### -# AID_MATCHING constants -# AID_MATCHING_EXACT_ONLY 0x00 -# AID_MATCHING_EXACT_OR_PREFIX 0x01 -# AID_MATCHING_PREFIX_ONLY 0x02 -# AID_MATCHING_EXACT_OR_SUBSET_OR_PREFIX 0x03 -AID_MATCHING_MODE=0x03 - -############################################################################### -# Default Secure Element route id -DEFAULT_OFFHOST_ROUTE=0x02 - -############################################################################### -# Vendor Specific Proprietary Protocol & Discovery Configuration -# Set to 0xFF if unsupported -# byte[0] NCI_PROTOCOL_18092_ACTIVE -# byte[1] NCI_PROTOCOL_B_PRIME -# byte[2] NCI_PROTOCOL_DUAL -# byte[3] NCI_PROTOCOL_15693 -# byte[4] NCI_PROTOCOL_KOVIO -# byte[5] NCI_PROTOCOL_MIFARE -# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO -# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME -# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME -NFA_PROPRIETARY_CFG={05:FF:FF:06:81:80:70:FF:FF} - -############################################################################### -# Bail out mode -# If set to 1, NFCC is using bail out mode for either Type A or Type B poll. -NFA_POLL_BAIL_OUT_MODE=0x01 -############################################################################### -# Enable/Disable Block Route feature. -# Block Route will restrict routing to first matched rule -# Block Route enable 0x01 -# Block Route disable 0x00 -NFA_BLOCK_ROUTE=0x00 |