diff options
Diffstat (limited to 'bluetooth')
| -rw-r--r-- | bluetooth/bt_vendor.conf | 102 | ||||
| -rw-r--r-- | bluetooth/vnd_shinano.txt | 4 |
2 files changed, 7 insertions, 99 deletions
diff --git a/bluetooth/bt_vendor.conf b/bluetooth/bt_vendor.conf index 1f4a63a..2d4267c 100644 --- a/bluetooth/bt_vendor.conf +++ b/bluetooth/bt_vendor.conf @@ -11,7 +11,7 @@ UimUartPort = /dev/ttyHS0 UartBaudRate = 3000000 # Firmware patch file location (compile default /vendor/firmware) -FwPatchFilePath = /system/etc/firmware +FwPatchFilePath = /vendor/firmware # uncomment if you want to load a specific version FwPatchFileName = BCM43xx.hcd @@ -25,94 +25,6 @@ FwPatchSettlementDelay = 100 # 1: active high (positive logic) (default) LpmWakePolarity = 1 -# stack/controller idle timeout in units (300/25ms) -# make sur controller supports 25ms -#LpmIdleTimeout = 2 - -#************************************** -# SCO I2S/PCM interface -# 0: PCM -# 1: I2S -#************************************** -#ScoInterface = 0 - -#************************************** -# SCO over PCM -# -# Configuration for SCO over PCM interface, which parameters are represented by array. -# Each PCM parameters' definations are listed as below, in order. Be NOTICED that -# this setting is ONLY VALID as PCM interface is selected/used. -# -# PCM Frame Type (SCO_PCM_IF_FRAME_TYPE) -# - 0: Short -# - 1: Long -# -# PCM Sync Mode (SCO_PCM_IF_SYNC_MODE) -# - 0: Slave -# - 1: Master -# -# PCM Clock Mode (SCO_PCM_IF_CLOCK_MODE) -# - 0: Slave -# - 1: Master -# -# PCM NBS(Narrow Band Speech) Clock Rate (SCO_PCM_IF_CLOCK_RATE) -# - 0: 128K -# - 1: 256K -# - 2: 512K -# - 3: 1024K -# - 4: 2048K -# -# PCM WBS(Wide Band Speech) Clock Rate (SCO_I2SPCM_IF_CLOCK_RATE4WBS) -# - 0: 128K -# - 1: 256K -# - 2: 512K -# - 3: 1024K -# - 4: 2048K -# -# PCM WBS (Wide Band Speech) Sample Rate (SCO_I2SPCM_IF_SAMPLE_RATE) -# -# - 0: 8K -# - 1: 16K -# - 2: 4K -# -# Carriers do not support 16K voice samples at present, -# so, setting PCM WBS Sample Rate to 8K (0) for now. -# -#************************************** -#ScoPCMifParams = {0,0,0,4,4,0} - -#************************************** -# PCM Format -# -# Configuration for PCM format, which parameters are represented by array. -# Each PCM format parameters' definations/descriptions are listed as below, in order. -# -# Shift Mode (PCM_DATA_FMT_SHIFT_MODE) -# - 0: MSB first -# - 1: LSB first -# -# Fill Bits (PCM_DATA_FMT_FILL_BITS) -# - Specifies the value with which to fill unused bits -# if Fill_Method is set to programmable -# -# Fill Method (PCM_DATA_FMT_FILL_METHOD) -# - 0 : 0's -# - 1 : 1's -# - 2 : Signed -# - 3 : Programmable -# -# Fill Num (PCM_DATA_FMT_FILL_NUM) -# - Specifies the number of bits to be filled -# -# Justify Mode (PCM_DATA_FMT_JUSTIFY_MODE) -# - 0: Left justify (fill data shifted out last) -# - 1: Right justify (fill data shifted out first) -# -#************************************** -#ScoPCMFmtParams = {0,0,3,0,0} - -####################################################################################### - ####################################################################################### # Configurations specific to V4L2 based solution ####################################################################################### @@ -122,14 +34,14 @@ LpmWakePolarity = 1 # enabled or if it is handled in the platform LpmEnable=true -#For hammerhead and grouper LPM is through bluesleep -#LPM for maguro and manta is done by UART driver itself +# For hammerhead and grouper LPM is through bluesleep +# LPM for maguro and manta is done by UART driver itself LpmUseBluesleep=false -#Set to true if bd address was programmed into firmware using OTP +# Set to true if bd address was programmed into firmware using OTP UseControllerBdaddr=false -#Enable debugging (add values below to enable multiple options) +# Enable debugging (add values below to enable multiple options) # enable logging in driver for init/release driver : 1 # enable logging in driver for open : 2 # enable logging in driver for close : 4 @@ -138,7 +50,3 @@ UseControllerBdaddr=false DBG_BT_DRV = 31 DBG_LDISC_DRV = 31 DBG_FM_DRV = 31 -#*************************************************************************** - -####################################################################################### - diff --git a/bluetooth/vnd_shinano.txt b/bluetooth/vnd_shinano.txt index 96c571c..c939e37 100644 --- a/bluetooth/vnd_shinano.txt +++ b/bluetooth/vnd_shinano.txt @@ -1,8 +1,8 @@ BLUETOOTH_UART_DEVICE_PORT = "/dev/ttyHS0" -FW_PATCHFILE_LOCATION = "/system/etc/firmware/" +FW_PATCHFILE_LOCATION = "/vendor/firmware/" FW_PATCHFILE_NAME = "BCM43xx.hcd" BT_WAKE_VIA_PROC = TRUE -BT_WAKE_VIA_PROC_NOTIFY_DEASSERT=TRUE +BT_WAKE_VIA_PROC_NOTIFY_DEASSERT = TRUE PROC_BTWRITE_TIMER_TIMEOUT_MS = 0 FW_PATCH_SETTLEMENT_DELAY_MS = 100 UART_TARGET_BAUD_RATE = 3000000 |