shinano: update wifi and bt

shinano use broadcom wlan instead of qcom

4 files changed, 0 insertions, 387 deletions

diff --git a/rootdir/system/etc/firmware/wlan/prima/WCNSS_cfg.dat b/rootdir/system/etc/firmware/wlan/prima/WCNSS_cfg.dat
deleted file mode 100644
index 5685e79..0000000
--- a/rootdir/system/etc/firmware/wlan/prima/WCNSS_cfg.dat
+++ /dev/null
diff --git a/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini b/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini
deleted file mode 100644
index 9778686..0000000
--- a/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini
+++ /dev/null
@@ -1,371 +0,0 @@
-# This file allows user to override the factory
-
-# defaults for the WLAN Driver
-
-
-# Enable IMPS or not
-gEnableImps=1
-
-# Enable/Disable Idle Scan
-
-gEnableIdleScan=0
-
-
-# Increase sleep duration (seconds) during IMPS
-# 0 implies no periodic wake up from IMPS. Periodic wakeup is
-# unnecessary if Idle Scan is disabled.
-gImpsModSleepTime=0
-
-
-# Enable BMPS or not
-gEnableBmps=1
-
-# Enable suspend or not
-
-# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
-
-gEnableSuspend=3
-
-
-# Phy Mode (auto, b, g, n, etc)
-# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
-gDot11Mode=0
-
-
-# CSR Roaming Enable(1) Disable(0)
-
-gRoamingTime=0
-
-
-# Assigned MAC Addresses - This will be used until NV items are in place
-
-# Each byte of MAC address is represented in Hex format as XX
-
-Intf0MacAddress=000AF58989FF
-Intf1MacAddress=000AF58989FE
-Intf2MacAddress=000AF58989FD
-
-Intf3MacAddress=000AF58989FC
-
-
-# UAPSD service interval for VO,VI, BE, BK traffic
-
-InfraUapsdVoSrvIntv=0
-
-InfraUapsdViSrvIntv=0
-
-InfraUapsdBeSrvIntv=0
-
-InfraUapsdBkSrvIntv=0
-
-# Flag to allow STA send AddTspec even when ACM is Off
-gAddTSWhenACMIsOff=1
-
-# Make 1x1 the default antenna configuration
-
-gNumRxAnt=1
-
-
-# Beacon filtering frequency (unit in beacon intervals)
-
-gNthBeaconFilter=50
-
-
-# Enable WAPI or not
-
-# WAPIIsEnabled=0
-
-
-# Flags to filter Mcast abd Bcast RX packets.
-
-# Value 0: No filtering, 1: Filter all Multicast.
-
-# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
-
-McastBcastFilter=3
-
-
-#Flag to enable HostARPOffload feature or not
-
-hostArpOffload=1
-
-
-#SoftAP Related Parameters
-
-# AP MAc addr
-
-gAPMacAddr=000AF589dcab
-
-
-# 802.11n Protection flag
-
-gEnableApProt=1
-
-
-#Enable OBSS protection
-
-gEnableApOBSSProt=1
-
-
-#Enable/Disable UAPSD for SoftAP
-
-gEnableApUapsd=0
-
-
-# Fixed Rate
-
-gFixedRate=0
-
-
-# Maximum Tx power
-
-# gTxPowerCap=30
-
-
-# Fragmentation Threshold
-
-# gFragmentationThreshold=2346
-
-
-# RTS threshold
-
-RTSThreshold=2347
-
-
-# Intra-BSS forward
-
-gDisableIntraBssFwd=0
-
-
-# WMM Enable/Disable
-
-WmmIsEnabled=0
-
-
-# 802.11d support
-
-g11dSupportEnabled=1
-
-# CCX Support and fast transition
-CcxEnabled=0
-FastTransitionEnabled=1
-ImplicitQosIsEnabled=0
-gNeighborScanTimerPeriod=200
-
-gNeighborLookupThreshold=78
-
-gNeighborScanChannelMinTime=20
-gNeighborScanChannelMaxTime=30
-
-# Legacy (non-CCX, non-802.11r) Fast Roaming Support
-# To enable, set FastRoamEnabled=1
-# To disable, set FastRoamEnabled=0
-FastRoamEnabled=1
-
-#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
-#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
-#the RSSI of the new/roamable AP should be for roaming
-RoamRssiDiff=5
-
-# SAP Country code
-
-# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
-
-# Example
-
-#   US Indoor, USI
-
-#   Korea Outdoor, KRO
-
-#   Japan without optional byte, JP
-
-#   France without optional byte, FR
-
-#gAPCntryCode=USI
-
-
-#Short Guard Interval Enable/disable
-
-gShortGI20Mhz=1
-
-gShortGI40Mhz=1
-
-
-#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
-
-gAPAutoShutOff=0
-
-
-# SAP auto channel selection configuration
-
-# 0 = disable auto channel selection
-
-# 1 = enable auto channel selection, channel provided by supplicant will be ignored
-
-gApAutoChannelSelection=0
-
-
-# Listen Energy Detect Mode Configuration
-
-# Valid values 0-128
-
-# 128 means disable Energy Detect feature
-
-# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
-
-# 10-128 are reserved.
-
-# The EDET threshold mapping is as follows in 3dB step:
-
-# 0 = -60 dBm
-
-# 1 = -63 dBm
-
-# 2 = -66 dBm
-
-# ...
-
-# 7 = -81 dBm
-
-# 8 = -84 dBm
-
-# 9 = -87 dBm
-
-# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
-
-#
-
-#  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.
-
-#
-
-gEnablePhyAgcListenMode=128
-
-
-#Preferred channel to start BT AMP AP mode (0 means, any channel)
-
-BtAmpPreferredChannel=0
-
-
-#Preferred band (both or 2.4 only or 5 only)
-
-BandCapability=0
-
-
-#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
-
-enableBeaconEarlyTermination=1
-
-beaconEarlyTerminationWakeInterval=11
-
-
-#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
-
-gEnableBtAmp=0
-
-
-#SOFTAP Channel Range selection
-
-gAPChannelSelectStartChannel=1
-
-gAPChannelSelectEndChannel=11
-
-
-#SOFTAP Channel Range selection Operating band
-
-# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
-
-gAPChannelSelectOperatingBand=0
-
-
-#Channel Bonding
-gChannelBondingMode5GHz=1
-
-
-#Enable Keep alive with non-zero period value
-
-gStaKeepAlivePeriod=30
-
-
-#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
-#For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
-#For both active and power save clients.
-
-#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
-#If doesn't honor for 5 seconds then Driver remove client.
-
-#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on
-#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
-#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod)..
-
-#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
-#where we send NULL frame.
-
-#gApLinkMonitorPeriod = 10
-
-#gGoLinkMonitorPeriod = 10
-
-#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
-#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
-#gGoKeepAlivePeriod = 5
-
-#gApKeepAlivePeriod = 5
-#If set will start with active scan after driver load, otherwise will start with
-
-#passive scan to find out the domain
-
-#gEnableBypass11d=1
-
-
-#If set to 0, will not scan DFS channels
-
-gEnableDFSChnlScan=1
-
-
-gVhtChannelWidth=2
-gEnableLogp=1
-
-
-# Enable Automatic Tx Power control
-
-gEnableAutomaticTxPowerControl=1
-
-# 0 for OLPC 1 for CLPC and SCPC
-gEnableCloseLoop=1
-
-#Data Inactivity Timeout when in powersave (in ms)
-gDataInactivityTimeout=200
-
-# VHT Tx/Rx MCS values
-# Valid values are 0,1,2. If commented out, the default value is 0.
-# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
-gVhtRxMCS=2
-gVhtTxMCS=2
-
-gEnableLpwrImgTransition=1
-
-# Enable Tx beamforming
-gTxBFEnable=1
-
-# Enable Tx LDPC
-#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
-gTxLdpcEnable=3
-
-#FlexConnect Power Factor
-#Default is set to 0 (disable)
-gFlexConnectPowerFactor=0
-
-# Valid values are 2048,4096,8192 and so on
-# Please don't use values other than the ones mentioned above
-gMaxMediumTime=4096
-
-# 802.11K support
-gRrmEnable=1
-gRrmOperChanMax=8
-gRrmNonOperChanMax=8
-gRrmRandIntvl=100
-
-END
-
-# Note: Configuration parser would not read anything past the END marker
-
diff --git a/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin b/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin
deleted file mode 100644
index a8dd301..0000000
--- a/rootdir/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin
+++ /dev/null
diff --git a/rootdir/system/etc/init.qcom.wifi.sh b/rootdir/system/etc/init.qcom.wifi.sh
deleted file mode 100644
index ea83027..0000000
--- a/rootdir/system/etc/init.qcom.wifi.sh
+++ /dev/null
@@ -1,16 +0,0 @@
-#!/system/bin/sh
-
-if [ -e /data/misc/wifi/WCNSS_qcom_wlan_cal.bin ]; then
-    calparm=`ls /sys/module/wcnsscore/parameters/has_calibrated_data`
-    if [ -e $calparm ] && [ ! -e /data/misc/wifi/WCN_FACTORY ]; then
-        echo 1 > $calparm
-    fi
-fi
-
-# There is a device file.  Write to the file
-# so that the driver knows userspace is
-# available for firmware download requests
-echo 1 > /dev/wcnss_wlan
-echo $serialno > /sys/devices/fb000000.qcom,wcnss-wlan/serial_number
-
-exit 0