shinano-commit: update bt_vendor.conf with stock .291

Change-Id: I469fcdffaadcda84afb01188623ad8fdc0ee94ac

1 files changed, 141 insertions, 1 deletions

diff --git a/bluetooth/bt_vendor.conf b/bluetooth/bt_vendor.conf
index 2508db5..02f3785 100644
--- a/bluetooth/bt_vendor.conf
+++ b/bluetooth/bt_vendor.conf
@@ -1,3 +1,143 @@
+#######################################################################################
+# Common configurations (applies to both V4L2 & non-V4L2)
+#######################################################################################
+
+# UART device port where Bluetooth controller is attached (default ttyS1)
 UartPort = /dev/ttyHS0
-FwPatchFilePath = /system/etc/firmware/
+
+# Target Baudrate to change to if different from 3000000
+# This entry is mandatory if using V4L2
+UartBaudRate = 3000000
+
+# Firmware patch file location (compile default /vendor/firmware)
+FwPatchFilePath = /system/etc/firmware
+
+# uncomment if you want to load a specific version
 FwPatchFileName = BCM43xx.hcd
+
+# Firmware patch setttlement delay in millisec
+# This entry is mandatory if using V4L2
+FwPatchSettlementDelay = 100
+
+# host/bt wake polarity to match with kernel settings
+# 0: active low (negative logic)
+# 1: active high (positive logic) (default)
+LpmWakePolarity = 1
+
+# stack/controller idle timeout in units (300/25ms)
+# make sur controller supports 25ms
+#LpmIdleTimeout = 2
+
+#**************************************
+# SCO I2S/PCM interface
+#   0: PCM
+#   1: I2S
+#**************************************
+#ScoInterface = 0
+
+#**************************************
+# SCO over PCM
+#
+# Configuration for SCO over PCM interface, which parameters are represented by array.
+# Each PCM parameters' definations are listed as below, in order. Be NOTICED that
+# this setting is ONLY VALID as PCM interface is selected/used.
+#
+#  PCM Frame Type (SCO_PCM_IF_FRAME_TYPE)
+#   - 0: Short
+#   - 1: Long
+#
+#  PCM Sync Mode (SCO_PCM_IF_SYNC_MODE)
+#   - 0: Slave
+#   - 1: Master
+#
+#  PCM Clock Mode (SCO_PCM_IF_CLOCK_MODE)
+#   - 0: Slave
+#   - 1: Master
+#
+#  PCM NBS(Narrow Band Speech) Clock Rate (SCO_PCM_IF_CLOCK_RATE)
+#   - 0:  128K
+#   - 1:  256K
+#   - 2:  512K
+#   - 3: 1024K
+#   - 4: 2048K
+#
+#  PCM WBS(Wide Band Speech) Clock Rate (SCO_I2SPCM_IF_CLOCK_RATE4WBS)
+#   - 0:  128K
+#   - 1:  256K
+#   - 2:  512K
+#   - 3: 1024K
+#   - 4: 2048K
+#
+# PCM WBS (Wide Band Speech) Sample Rate (SCO_I2SPCM_IF_SAMPLE_RATE)
+#
+#   - 0: 8K
+#   - 1: 16K
+#   - 2: 4K
+#
+#    Carriers do not support 16K voice samples at present,
+#    so, setting PCM WBS Sample Rate to 8K (0) for now.
+#
+#**************************************
+#ScoPCMifParams = {0,0,0,4,4,0}
+
+#**************************************
+# PCM Format
+#
+# Configuration for PCM format, which parameters are represented by array.
+# Each PCM format parameters' definations/descriptions are listed as below, in order.
+#
+#  Shift Mode (PCM_DATA_FMT_SHIFT_MODE)
+#   - 0: MSB first
+#   - 1: LSB first
+#
+#  Fill Bits (PCM_DATA_FMT_FILL_BITS)
+#   - Specifies the value with which to fill unused bits
+#     if Fill_Method is set to programmable
+#
+#  Fill Method (PCM_DATA_FMT_FILL_METHOD)
+#   - 0 : 0's
+#   - 1 : 1's
+#   - 2 : Signed
+#   - 3 : Programmable
+#
+#  Fill Num (PCM_DATA_FMT_FILL_NUM)
+#   - Specifies the number of bits to be filled
+#
+#  Justify Mode (PCM_DATA_FMT_JUSTIFY_MODE)
+#   - 0: Left justify (fill data shifted out last)
+#   - 1: Right justify (fill data shifted out first)
+#
+#**************************************
+#ScoPCMFmtParams = {0,0,3,0,0}
+
+#######################################################################################
+
+#######################################################################################
+# Configurations specific to V4L2 based solution
+#######################################################################################
+
+# Setting this to true enables Low Power Mode (LPM) in the shared
+# line discipline driver. Set this to fale if the LPM is not
+# enabled or if it is handled in the platform
+LpmEnable=true
+
+#For hammerhead and grouper LPM is through bluesleep
+#LPM for maguro and manta is done by UART driver itself
+LpmUseBluesleep=false
+
+#Set to true if bd address was programmed into firmware using OTP
+UseControllerBdaddr=false
+
+#Enable debugging (add values below to enable multiple options)
+# enable logging in driver for init/release driver      : 1
+# enable logging in driver for open                     : 2
+# enable logging in driver for close                    : 4
+# enable logging in driver for Tx                       : 8
+# enable logging in driver for Rx                       : 16
+DBG_BT_DRV = 31
+DBG_LDISC_DRV = 31
+DBG_FM_DRV = 31
+#***************************************************************************
+
+#######################################################################################
+