shinano-common: pn54x: Clean libnfc-brcm.conf

Change-Id: Icb7e64684d7722bd4ec350409a5e9a0be247f59d

1 files changed, 0 insertions, 206 deletions

diff --git a/pn54x/libnfc-brcm.conf b/pn54x/libnfc-brcm.conf
index 7fa54bd..9d1d8af 100644
--- a/pn54x/libnfc-brcm.conf
+++ b/pn54x/libnfc-brcm.conf
@@ -6,55 +6,14 @@ APPL_TRACE_LEVEL=0xFF
 PROTOCOL_TRACE_LEVEL=0xFFFFFFFF
 
 ###############################################################################
-# performance measurement
-# Change this setting to control how often USERIAL log the performance (throughput)
-# data on read/write/poll
-# defailt is to log performance dara for every 100 read or write
-#REPORT_PERFORMANCE_MEASURE=100
-
-###############################################################################
 # File used for NFA storage
 NFA_STORAGE="/data/nfc"
 
 ###############################################################################
-# Snooze Mode Settings
-#
-#  By default snooze mode is enabled.  Set SNOOZE_MODE_CFG byte[0] to 0
-#  to disable.
-#
-#  If SNOOZE_MODE_CFG is not provided, the default settings are used:
-#  They are as follows:
-#       8             Sleep Mode (0=Disabled 1=UART 8=SPI/I2C)
-#       0             Idle Threshold Host
-#       0             Idle Threshold HC
-#       0             NFC Wake active mode (0=ActiveLow 1=ActiveHigh)
-#       1             Host Wake active mode (0=ActiveLow 1=ActiveHigh)
-#
-#SNOOZE_MODE_CFG={08:00:00:00:01}
-
-###############################################################################
 # Insert a delay in milliseconds after NFC_WAKE and before write to NFCC
 NFC_WAKE_DELAY=20
 
 ###############################################################################
-# Various Delay settings (in ms) used in USERIAL
-#  POWER_ON_DELAY
-#    Delay after turning on chip, before writing to transport (default 300)
-#  PRE_POWER_OFF_DELAY
-#    Delay after deasserting NFC-Wake before turn off chip (default 0)
-#  POST_POWER_OFF_DELAY
-#    Delay after turning off chip, before USERIAL_close returns (default 0)
-#
-#POWER_ON_DELAY=300
-#PRE_POWER_OFF_DELAY=0
-#POST_POWER_OFF_DELAY=0
-
-###############################################################################
-# Maximum time (ms) to wait for RESET NTF after setting REG_PU to high
-# The default is 1000.
-#NFCC_ENABLE_TIMEOUT=0
-
-###############################################################################
 # LPTD mode configuration
 #  byte[0] is the length of the remaining bytes in this value
 #     if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled).
@@ -80,51 +39,11 @@ LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:0
 NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:80:01:01}
 
 ###############################################################################
-# Startup Vendor Specific Configuration (100 bytes maximum);
-#  byte[0] TLV total len = 0x5
-#  byte[1] NCI_MTS_CMD|NCI_GID_PROP = 0x2f
-#  byte[2] NCI_MSG_FRAME_LOG = 0x9
-#  byte[3] 2
-#  byte[4] 0=turn off RF frame logging; 1=turn on
-#  byte[5] 0=turn off SWP frame logging; 1=turn on
-#  NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01}
-
-###############################################################################
-# Antenna Configuration - This data is used when setting 0xC8 config item
-# at startup (before discovery is started).  If not used, no value is sent.
-#
-# The settings for this value are documented here:
-# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
-#   Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
-# This document is maintained by Paul Forshaw.
-#
-# The values marked as ?? should be tweaked per antenna or customer/app:
-# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
-# array[0] = 0x20 is length of the payload from array[1] to the end
-# array[1] = 0xC8 is PREINIT_DSP_CFG
-#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}
-
-###############################################################################
-# Configure crystal frequency when internal LPO can't detect the frequency.
-#XTAL_FREQUENCY=0
-###############################################################################
 # Configure the default Destination Gate used by HCI (the default is 4, which
 # is the ETSI loopback gate.
 NFA_HCI_DEFAULT_DEST_GATE=0xF0
 
 ###############################################################################
-# Configure the single default SE to use.  The default is to use the first
-# SE that is detected by the stack.  This value might be used when the phone
-# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
-# one of them (e.g. 0xF4).
-#ACTIVE_SE=0xF3
-
-###############################################################################
-# Configure the default NfcA/IsoDep techology and protocol route. Can be
-# either a secure element (e.g. 0xF4) or the host (0x00)
-#DEFAULT_ISODEP_ROUTE=0x00
-
-###############################################################################
 # Configure the NFC Extras to open and use a static pipe.  If the value is
 # not set or set to 0, then the default is use a dynamic pipe based on a
 # destination gate (see NFA_HCI_DEFAULT_DEST_GATE).  Note there is a value
@@ -169,18 +88,6 @@ UICC_IDLE_TIMEOUT=0
 # If specified, this AID will be substituted when an Empty SELECT command is
 # detected.  The first byte is the length of the AID.  Maximum length is 16.
 AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00}
-###############################################################################
-# Maximum Number of Credits to be allowed by the NFCC
-#   This value overrides what the NFCC specifices allowing the host to have
-#   the control to work-around transport limitations.  If this value does
-#   not exist or is set to 0, the NFCC will provide the number of credits.
-MAX_RF_DATA_CREDITS=1
-
-###############################################################################
-# This setting allows you to disable registering the T4t Virtual SE that causes
-# the NFCC to send PPSE requests to the DH.
-# The default setting is enabled (i.e. T4t Virtual SE is registered).
-#REGISTER_VIRTUAL_SE=1
 
 ###############################################################################
 # When screen is turned off, specify the desired power state of the controller.
@@ -200,79 +107,6 @@ FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd"
 FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd"
 
 ###############################################################################
-# Firmware patch format
-#   1 = HCD
-#   2 = NCD (default)
-#NFA_CONFIG_FORMAT=2
-
-###############################################################################
-# SPD Debug mode
-#  If set to 1, any failure of downloading a patch will trigger a hard-stop
-#SPD_DEBUG=0
-
-###############################################################################
-# SPD Max Retry Count
-#  The number of attempts to download a patch before giving up (defualt is 3).
-#  Note, this resets after a power-cycle.
-#SPD_MAX_RETRY_COUNT=3
-
-###############################################################################
-# transport driver
-#
-# TRANSPORT_DRIVER=<driver>
-#
-#  where <driver> can be, for example:
-#    "/dev/ttyS"        (UART)
-#    "/dev/bcmi2cnfc"   (I2C)
-#    "hwtun"            (HW Tunnel)
-#    "/dev/bcmspinfc"   (SPI)
-#    "/dev/btusb0"      (BT USB)
-#TRANSPORT_DRIVER="/dev/bcm2079x-i2c"
-
-###############################################################################
-# power control driver
-# Specify a kernel driver that support ioctl commands to control NFC_EN and
-# NFC_WAKE gpio signals.
-#
-# POWER_CONTRL_DRIVER=<driver>
-#  where <driver> can be, for example:
-#    "/dev/nfcpower"
-#    "/dev/bcmi2cnfc"   (I2C)
-#    "/dev/bcmspinfc"   (SPI)
-#    i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal
-#POWER_CONTROL_DRIVER="/dev/bcm2079x-i2c"
-
-###############################################################################
-# I2C transport driver options
-# Mako does not support 10-bit I2C addresses
-# Revert to 7-bit address
-#BCMI2CNFC_ADDRESS=0x77
-
-###############################################################################
-# I2C transport driver try to read multiple packets in read() if data is available
-# remove the comment below to enable this feature
-#READ_MULTIPLE_PACKETS=1
-
-###############################################################################
-# SPI transport driver options
-#SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00}
-
-###############################################################################
-# UART transport driver options
-#
-# PORT=1,2,3,...
-# BAUD=115200, 19200, 9600, 4800,
-# DATABITS=8, 7, 6, 5
-# PARITY="even" | "odd" | "none"
-# STOPBITS="0" | "1" | "1.5" | "2"
-
-#UART_PORT=2
-#UART_BAUD=115200
-#UART_DATABITS=8
-#UART_PARITY="none"
-#UART_STOPBITS="1"
-
-###############################################################################
 # Insert a delay in microseconds per byte after a write to NFCC.
 # after writing a block of data to the NFCC, delay this an amopunt of time before
 # writing next block of data.  the delay is calculated as below
@@ -281,41 +115,6 @@ FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd"
 NFC_WRITE_DELAY=20
 
 ###############################################################################
-# Maximum Number of Credits to be allowed by the NFCC
-#   This value overrides what the NFCC specifices allowing the host to have
-#   the control to work-around transport limitations.  If this value does
-#   not exist or is set to 0, the NFCC will provide the number of credits.
-MAX_RF_DATA_CREDITS=1
-
-###############################################################################
-# Default poll duration (in ms)
-#  The defualt is 500ms if not set (see nfc_target.h)
-#NFA_DM_DISC_DURATION_POLL=333
-###############################################################################
-# Antenna Configuration - This data is used when setting 0xC8 config item
-# at startup (before discovery is started).  If not used, no value is sent.
-#
-# The settings for this value are documented here:
-# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
-#   Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
-# This document is maintained by Paul Forshaw.
-#
-# The values marked as ?? should be tweaked per antenna or customer/app:
-# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
-# array[0] = 0x20 is length of the payload from array[1] to the end
-# array[1] = 0xC8 is PREINIT_DSP_CFG
-#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}
-
-###############################################################################
-# Choose the presence-check algorithm for type-4 tag.  If not defined, the default value is 1.
-# 0  NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
-# 1  NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
-# 2  NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate
-# 3  NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0
-# 4  NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3
-PRESENCE_CHECK_ALGORITHM=1
-
-###############################################################################
 # Force tag polling for the following technology(s).
 # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
 # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B |
@@ -365,11 +164,6 @@ NFA_MAX_EE_SUPPORTED=0x02
 # NCI Hal Module name
 NCI_HAL_MODULE="nfc_nci"
 
-##############################################################################
-# Deactivate notification wait time out in seconds used in ETSI Reader mode
-# 0 - Infinite wait
-#NFA_DM_DISC_NTF_TIMEOUT=0
-
 ###############################################################################
 # AID_MATCHING constants
 # AID_MATCHING_EXACT_ONLY 0x00