/** @file

Copyright (c) 2020, Intel Corporation. All rights reserved.<BR>

Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this
  list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
  list of conditions and the following disclaimer in the documentation and/or
  other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
  be used to endorse or promote products derived from this software without
  specific prior written permission.

  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
  THE POSSIBILITY OF SUCH DAMAGE.

  This file is automatically generated. Please do NOT modify !!!

**/

#ifndef __FSPSUPD_H__
#define __FSPSUPD_H__

#include <FspUpd.h>

#pragma pack(1)


///
/// Azalia Header structure
///
typedef struct {
  UINT16 VendorId;           ///< Codec Vendor ID
  UINT16 DeviceId;           ///< Codec Device ID
  UINT8  RevisionId;         ///< Revision ID of the codec. 0xFF matches any revision.
  UINT8  SdiNum;             ///< SDI number, 0xFF matches any SDI.
  UINT16 DataDwords;         ///< Number of data DWORDs pointed by the codec data buffer.
  UINT32 Reserved;           ///< Reserved for future use. Must be set to 0.
} AZALIA_HEADER;

///
/// Audio Azalia Verb Table structure
///
typedef struct {
  AZALIA_HEADER Header;      ///< AZALIA PCH header
  UINT32        *Data;       ///< Pointer to the data buffer. Its length is specified in the header
} AUDIO_AZALIA_VERB_TABLE;

///
/// Refer to the definition of PCH_INT_PIN
///
typedef enum {
  SiPchNoInt,        ///< No Interrupt Pin
  SiPchIntA,
  SiPchIntB,
  SiPchIntC,
  SiPchIntD
} SI_PCH_INT_PIN;
///
/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device.
///
typedef struct {
  UINT8        Device;                  ///< Device number
  UINT8        Function;                ///< Device function
  UINT8        IntX;                    ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN)
  UINT8        Irq;                     ///< IRQ to be set for device.
} SI_PCH_DEVICE_INTERRUPT_CONFIG;

#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG  64       ///< Number of all PCH devices


/** Fsp S Configuration
**/
typedef struct {

/** Offset 0x0020 - Reserved
**/
  UINT8                      Reserved0[16];

/** Offset 0x0030 - Graphics Configuration Ptr
  Points to VBT
**/
  UINT32                      GraphicsConfigPtr;

/** Offset 0x0034 - Enable Device 4
  Enable/disable Device 4
  $EN_DIS
**/
  UINT8                       Device4Enable;

/** Offset 0x0035 - Enable eMMC Controller
  Enable/disable eMMC Controller.
  $EN_DIS
**/
  UINT8                       ScsEmmcEnabled;

/** Offset 0x0036 - Enable eMMC HS400 Mode
  Enable eMMC HS400 Mode.
  $EN_DIS
**/
  UINT8                       ScsEmmcHs400Enabled;

/** Offset 0x0037 - Use DLL values from policy
  Set if FSP should use HS400 DLL values from policy
  $EN_DIS
**/
  UINT8                       EmmcUseCustomDlls;

/** Offset 0x0038 - Emmc Tx CMD Delay control register value
  Please see Tx CMD Delay Control register definition for help
**/
  UINT32                      EmmcTxCmdDelayRegValue;

/** Offset 0x003C - Emmc Tx DATA Delay control 1 register value
  Please see Tx DATA Delay control 1 register definition for help
**/
  UINT32                      EmmcTxDataDelay1RegValue;

/** Offset 0x0040 - Emmc Tx DATA Delay control 2 register value
  Please see Tx DATA Delay control 2 register definition for help
**/
  UINT32                      EmmcTxDataDelay2RegValue;

/** Offset 0x0044 - Emmc Rx CMD + DATA Delay control 1 register value
  Please see Rx CMD + DATA Delay control 1 register definition for help
**/
  UINT32                      EmmcRxCmdDataDelay1RegValue;

/** Offset 0x0048 - Emmc Rx CMD + DATA Delay control 2 register value
  Please see Rx CMD + DATA Delay control 2 register definition for help
**/
  UINT32                      EmmcRxCmdDataDelay2RegValue;

/** Offset 0x004C - Emmc Rx Strobe Delay control register value
  Please see Rx Strobe Delay control register definition for help
**/
  UINT32                      EmmcRxStrobeDelayRegValue;

/** Offset 0x0050 - Enable SdCard Controller
  Enable/disable SD Card Controller.
  $EN_DIS
**/
  UINT8                       ScsSdCardEnabled;

/** Offset 0x0051 - SdCard power enable polarity
  Choose SD_PWREN# polarity
  0: Active low, 1: Active high
**/
  UINT8                       SdCardPowerEnableActiveHigh;

/** Offset 0x0052 - Reserved
**/
  UINT8                       Reserved1[34];

/** Offset 0x0074 - SdCard Command Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       SdCardGpioCmdPadTermination;

/** Offset 0x0075 - Reserved
**/
  UINT8                       Reserved2[135];

/** Offset 0x00FC - Turbo Mode
  Enable/Disable Turbo mode. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       TurboMode;

/** Offset 0x00FD - Enable SATA SALP Support
  Enable/disable SATA Aggressive Link Power Management.
  $EN_DIS
**/
  UINT8                       SataSalpSupport;

/** Offset 0x00FE - Enable SATA ports
  Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1,
  and so on.
**/
  UINT8                       SataPortsEnable[8];

/** Offset 0x0106 - Enable SATA DEVSLP Feature
  Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each
  port, byte0 for port0, byte1 for port1, and so on.
**/
  UINT8                       SataPortsDevSlp[8];

/** Offset 0x010E - Enable USB2 ports
  Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for
  port1, and so on.
**/
  UINT8                       PortUsb20Enable[16];

/** Offset 0x011E - Enable USB3 ports
  Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for
  port1, and so on.
**/
  UINT8                       PortUsb30Enable[10];

/** Offset 0x0128 - Enable xDCI controller
  Enable/disable to xDCI controller.
  $EN_DIS
**/
  UINT8                       XdciEnable;

/** Offset 0x0129 - Reserved
**/
  UINT8                       Reserved3[28];

/** Offset 0x0145 - Enable SATA
  Enable/disable SATA controller.
  $EN_DIS
**/
  UINT8                       SataEnable;

/** Offset 0x0146 - SATA Mode
  Select SATA controller working mode.
  0:AHCI, 1:RAID
**/
  UINT8                       SataMode;

/** Offset 0x0147 - SPIn Device Mode
  Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available
  modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden
**/
  UINT8                       SerialIoSpiMode[7];

/** Offset 0x014E - SPI<N> Chip Select Polarity
  Sets polarity for each chip Select. Available options: 0:SerialIoSpiCsActiveLow,
  1:SerialIoSpiCsActiveHigh
**/
  UINT8                       SerialIoSpiCsPolarity[14];

/** Offset 0x015C - Reserved
**/
  UINT8                       Reserved4[21];

/** Offset 0x0171 - SPIn Default Chip Select Mode HW/SW
  Sets Default CS Mode Hardware or Software. N represents controller index: SPI0,
  SPI1, ... Available options: 0:HW, 1:SW
**/
  UINT8                       SerialIoSpiCsMode[7];

/** Offset 0x0178 - SPIn Default Chip Select State Low/High
  Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ...
  Available options: 0:Low, 1:High
**/
  UINT8                       SerialIoSpiCsState[7];

/** Offset 0x017F - UARTn Device Mode
  Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available
  modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
  4:SerialIoUartSkipInit
**/
  UINT8                       SerialIoUartMode[7];

/** Offset 0x0186 - Reserved
**/
  UINT8                       Reserved5[186];

/** Offset 0x0240 - UART Number For Debug Purpose
  UART number for debug purpose. 0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5,
  6:UART6. Note: If UART0 is selected as CNVi BT Core interface, it cannot be used
  for debug purpose.
   0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5, 6:UART6
**/
  UINT8                       SerialIoDebugUartNumber;

/** Offset 0x0241 - Reserved
**/
  UINT8                       Reserved6[7];

/** Offset 0x0248 - I2Cn Device Mode
  Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available
  modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden
**/
  UINT8                       SerialIoI2cMode[8];

/** Offset 0x0250 - Serial IO I2C SDA Pin Muxing
  Select SerialIo I2c Sda pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SDA* for
  possible values.
**/
  UINT32                      PchSerialIoI2cSdaPinMux[8];

/** Offset 0x0270 - Serial IO I2C SCL Pin Muxing
  Select SerialIo I2c Scl pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SCL* for
  possible values.
**/
  UINT32                      PchSerialIoI2cSclPinMux[8];

/** Offset 0x0290 - Reserved
**/
  UINT8                       Reserved7[8];

/** Offset 0x0298 - USB Per Port HS Preemphasis Bias
  USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
  100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port.
**/
  UINT8                       Usb2PhyPetxiset[16];

/** Offset 0x02A8 - USB Per Port HS Transmitter Bias
  USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
  100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port.
**/
  UINT8                       Usb2PhyTxiset[16];

/** Offset 0x02B8 - USB Per Port HS Transmitter Emphasis
  USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON,
  10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port.
**/
  UINT8                       Usb2PhyPredeemp[16];

/** Offset 0x02C8 - USB Per Port Half Bit Pre-emphasis
  USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis.
  One byte for each port.
**/
  UINT8                       Usb2PhyPehalfbit[16];

/** Offset 0x02D8 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment
  Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value
  in arrary can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxDeEmphEnable[10];

/** Offset 0x02E2 - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting
  USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16],
  <b>Default = 29h</b> (approximately -3.5dB De-Emphasis). One byte for each port.
**/
  UINT8                       Usb3HsioTxDeEmph[10];

/** Offset 0x02EC - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment
  Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value
  in arrary can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxDownscaleAmpEnable[10];

/** Offset 0x02F6 - USB 3.0 TX Output Downscale Amplitude Adjustment
  USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], <b>Default
  = 00h</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxDownscaleAmp[10];

/** Offset 0x0300 - Enable LAN
  Enable/disable LAN controller.
  $EN_DIS
**/
  UINT8                       PchLanEnable;

/** Offset 0x0301 - Reserved
**/
  UINT8                       Reserved8[81];

/** Offset 0x0352 - Mask to enable the usage of external V1p05 VR rail in specific S0ix or Sx states
  Enable External V1P05 Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5
**/
  UINT8                       PchFivrExtV1p05RailEnabledStates;

/** Offset 0x0353 - Reserved
**/
  UINT8                       Reserved9;

/** Offset 0x0354 - External V1P05 Voltage Value that will be used in S0i2/S0i3 states
  Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...)
**/
  UINT16                      PchFivrExtV1p05RailVoltage;

/** Offset 0x0356 - External V1P05 Icc Max Value
  Granularity of this setting is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtV1p05RailIccMax;

/** Offset 0x0357 - Reserved
**/
  UINT8                       Reserved10;

/** Offset 0x0358 - External Vnn Voltage Value that will be used in S0ix/Sx states
  Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...)
**/
  UINT16                      PchFivrExtVnnRailVoltage;

/** Offset 0x035A - External Vnn Icc Max Value that will be used in S0ix/Sx states
  Granularity of this setting is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtVnnRailIccMax;

/** Offset 0x035B - Mask to enable the usage of external Vnn VR rail in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Enable External Vnn Rail in
  Sx: BIT0-1:Reserved, BIT2:S3, BIT3:S4, BIT5:S5
**/
  UINT8                       PchFivrExtVnnRailSxEnabledStates;

/** Offset 0x035C - External Vnn Voltage Value that will be used in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments
  (0=0mV, 1=2.5mV, 2=5mV...)
**/
  UINT16                      PchFivrExtVnnRailSxVoltage;

/** Offset 0x035E - External Vnn Icc Max Value that will be used in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
  is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtVnnRailSxIccMax;

/** Offset 0x035F - Transition time in microseconds from Low Current Mode Voltage to High Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to low current mode voltage.
**/
  UINT8                       PchFivrVccinAuxLowToHighCurModeVolTranTime;

/** Offset 0x0360 - Transition time in microseconds from Retention Mode Voltage to High Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to retention mode voltage.
**/
  UINT8                       PchFivrVccinAuxRetToHighCurModeVolTranTime;

/** Offset 0x0361 - Transition time in microseconds from Retention Mode Voltage to Low Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to retention mode voltage.
**/
  UINT8                       PchFivrVccinAuxRetToLowCurModeVolTranTime;

/** Offset 0x0362 - Transition time in microseconds from Off (0V) to High Current Mode Voltage
  This field has 1us resolution. When value is 0 Transition to 0V is disabled.
**/
  UINT16                      PchFivrVccinAuxOffToHighCurModeVolTranTime;

/** Offset 0x0364 - Reserved
**/
  UINT8                      Reserved11[20];

/** Offset 0x0378 - CNVi Configuration
  This option allows for automatic detection of Connectivity Solution. [Auto Detection]
  assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi.
  0:Disable, 1:Auto
**/
  UINT8                       CnviMode;

/** Offset 0x0379 - CNVi BT Core
  Enable/Disable CNVi BT Core, Default is ENABLE. 0: DISABLE, 1: ENABLE
  $EN_DIS
**/
  UINT8                       CnviBtCore;

/** Offset 0x037A - CNVi BT Audio Offload
  Enable/Disable BT Audio Offload, Default is DISABLE. 0: DISABLE, 1: ENABLE
  $EN_DIS
**/
  UINT8                       CnviBtAudioOffload;

/** Offset 0x037B - Reserved
**/
  UINT8                       Reserved12;

/** Offset 0x037C - CNVi RF_RESET pin muxing
  Select CNVi RF_RESET# pin depending on board routing. ICP-N: GPP_H12 = 0x2746E40C(default)
  or GPP_H1 = 0x3746E401. Refer to GPIO_*_MUXING_CNVI_RF_RESET_* in GpioPins*.h.
**/
  UINT32                      CnviRfResetPinMux;

/** Offset 0x0380 - CNVi CLKREQ pin muxing
  Select CNVi CLKREQ pin depending on board routing. ICP-N: GPP_H13 = 0x2746E60D(default)
  or GPP_H2 = 0x3746E602. Refer to GPIO_*_MUXING_CNVI_MODEM_CLKREQ_* in GpioPins*.h.
**/
  UINT32                      CnviClkreqPinMux;

/** Offset 0x0384 - Reserved
**/
  UINT8                       Reserved13[145];

/** Offset 0x0415 - Enable/Disable PavpEnable
  Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable
  $EN_DIS
**/
  UINT8                       PavpEnable;

/** Offset 0x0416 - CdClock Frequency selection
  0: (Default) Auto (Max based on reference clock frequency), 1: 172.8 Mhz, 2: 180
  Mhz, 3: 190 Mhz, 4: 307.2 Mhz, 5: 312 Mhz, 6: 552 Mhz, 7: 556.8 Mhz, 8: 648 Mhz,
  9: 652.8 Mhz
  0: Auto (Max based on reference clock frequency), 1: 172.8 Mhz, 2: 180 Mhz, 3: 190
  Mhz, 4: 307.2 Mhz, 5: 312 Mhz, 6: 552 Mhz, 7: 556.8 Mhz, 8: 648 Mhz, 9: 652.8 Mhz
**/
  UINT8                       CdClock;

/** Offset 0x0417 - Enable/Disable PeiGraphicsPeimInit
  Enable: FSP will initialize the framebuffer and provide it via EFI_PEI_GRAPHICS_INFO_HOB.
  <b>Disable(Default):</b> FSP will NOT initialize the framebuffer.
  $EN_DIS
**/
  UINT8                       PeiGraphicsPeimInit;

/** Offset 0x0418 - Reserved
**/
  UINT8                       Reserved14[152];

/** Offset 0x04B0 - Skip Multi-Processor Initialization
  When this is skipped, boot loader must initialize processors before SilicionInit
  API. </b>0: Initialize; <b>1: Skip
  $EN_DIS
**/
  UINT8                       SkipMpInit;

/** Offset 0x04B1 - Reserved
**/
  UINT8                       Reserved15[11];

/** Offset 0x04BC - CpuMpPpi
  <b>Optional</b> pointer to the boot loader's implementation of EFI_PEI_MP_SERVICES_PPI.
  If not NULL, FSP will use the boot loader's implementation of multiprocessing.
  See section 5.1.4 of the FSP Integration Guide for more details.
**/
  UINT32                      CpuMpPpi;

/** Offset 0x04C0 - Reserved
**/
  UINT8                      Reserved16[83];

/** Offset 0x0513 - Enable LOCKDOWN BIOS LOCK
  Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region
  protection.
  $EN_DIS
**/
  UINT8                       PchLockDownBiosLock;

/** Offset 0x0514 - Reserved
**/
  UINT8                       Reserved17[2];

/** Offset 0x0516 - RTC Cmos Memory Lock
  Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper
  and and lower 128-byte bank of RTC RAM.
  $EN_DIS
**/
  UINT8                       RtcMemoryLock;

/** Offset 0x0517 - Reserved
**/
  UINT8                       Reserved18[24];

/** Offset 0x052F - Enable PCIE RP Pm Sci
  Indicate whether the root port power manager SCI is enabled.
**/
  UINT8                       PcieRpPmSci[24];

/** Offset 0x0547 - Reserved
**/
  UINT8                       Reserved19[24];

/** Offset 0x055F - Enable PCIE RP Clk Req Detect
  Probe CLKREQ# signal before enabling CLKREQ# based power management.
**/
  UINT8                       PcieRpClkReqDetect[24];

/** Offset 0x0577 - Reserved
**/
  UINT8                       Reserved20[455];

/** Offset 0x073E - PCH Pm Slp S3 Min Assert
  SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms.
**/
  UINT8                       PchPmSlpS3MinAssert;

/** Offset 0x073F - Reserved
**/
  UINT8                       Reserved21;

/** Offset 0x0740 - PCH Pm Slp Sus Min Assert
  SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s.
**/
  UINT8                       PchPmSlpSusMinAssert;

/** Offset 0x0741 - PCH Pm Slp A Min Assert
  SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s.
**/
  UINT8                       PchPmSlpAMinAssert;

/** Offset 0x0742 - Reserved
**/
  UINT8                       Reserved22[11];

/** Offset 0x074D - PCH Sata Pwr Opt Enable
  SATA Power Optimizer on PCH side.
  $EN_DIS
**/
  UINT8                       SataPwrOptEnable;

/** Offset 0x074E - Reserved
**/
  UINT8                       Reserved23[146];

/** Offset 0x07E0 - USB2 Port Over Current Pin
  Describe the specific over current pin number of USB 2.0 Port N.
**/
  UINT8                       Usb2OverCurrentPin[16];

/** Offset 0x07F0 - USB3 Port Over Current Pin
  Describe the specific over current pin number of USB 3.0 Port N.
**/
  UINT8                       Usb3OverCurrentPin[10];

/** Offset 0x07FA - Enable 8254 Static Clock Gating
  Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time
  might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support
  legacy OS using 8254 timer. Also enable this while S0ix is enabled.
  $EN_DIS
**/
  UINT8                       Enable8254ClockGating;

/** Offset 0x07FB - Enable 8254 Static Clock Gating On S3
  This is only applicable when Enable8254ClockGating is disabled. FSP will do the
  8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This
  avoids the SMI requirement for the programming.
  $EN_DIS
**/
  UINT8                       Enable8254ClockGatingOnS3;

/** Offset 0x07FC - Reserved
**/
  UINT8                       Reserved24[487];

/** Offset 0x09E3 - Enable/Disable IGFX PmSupport
  Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport
  $EN_DIS
**/
  UINT8                       PmSupport;

/** Offset 0x09E4 - Reserved
**/
  UINT8                       Reserved25[32];

/** Offset 0x0A04 - TCC Activation Offset
  TCC Activation Offset. Offset from factory set TCC activation temperature at which
  the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation
  Temperature, in volts.For SKL Y SKU, the recommended default for this policy is
  <b>10</b>, For all other SKUs the recommended default are <b>0</b>
**/
  UINT8                       TccActivationOffset;

/** Offset 0x0A05 - Reserved
**/
  UINT8                       Reserved26[34];

/** Offset 0x0A27 - Enable or Disable CPU power states (C-states)
  Enable or Disable CPU power states (C-states). 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       Cx;

/** Offset 0x0A28 - Reserved
**/
  UINT8                       Reserved27[74];

/** Offset 0x0A72 - Platform Power Pmax
  PCODE MMIO Mailbox: Platform Power Pmax. <b>0 - Auto</b> Specified in 1/8 Watt increments.
  Range 0-1024 Watts. Value of 800 = 100W
**/
  UINT16                      PsysPmax;

/** Offset 0x0A74 - Reserved
**/
  UINT8                      Reserved28[115];

/** Offset 0x0AE7 - End of Post message
  Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1):
  EOP send in PEI, Send in DXE(0x2)(Default): EOP send in DXE
  0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved
**/
  UINT8                       EndOfPostMessage;

/** Offset 0x0AE8 - Reserved
**/
  UINT8                       Reserved29;

/** Offset 0x0AE9 - Enable LOCKDOWN SMI
  Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.
  $EN_DIS
**/
  UINT8                       PchLockDownGlobalSmi;

/** Offset 0x0AEA - Enable LOCKDOWN BIOS Interface
  Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register.
  $EN_DIS
**/
  UINT8                       PchLockDownBiosInterface;

/** Offset 0x0AEB - Unlock all GPIO pads
  Force all GPIO pads to be unlocked for debug purpose.
  $EN_DIS
**/
  UINT8                       PchUnlockGpioPads;

/** Offset 0x0AEC - Reserved
**/
  UINT8                       Reserved30[452];
} FSP_S_CONFIG;

/** Fsp S UPD Configuration
**/
typedef struct {

/** Offset 0x0000
**/
  FSP_UPD_HEADER              FspUpdHeader;

/** Offset 0x0020
**/
  FSP_S_CONFIG                FspsConfig;

/** Offset 0x0CB0
**/
  UINT8                       UnusedUpdSpace36[6];

/** Offset 0x0CB6
**/
  UINT16                      UpdTerminator;
} FSPS_UPD;

#pragma pack()

#endif