/** @file Copyright (c) 2020, Intel Corporation. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * Neither the name of Intel Corporation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This file is automatically generated. Please do NOT modify !!! **/ #ifndef __FSPSUPD_H__ #define __FSPSUPD_H__ #include #pragma pack(1) /// /// Azalia Header structure /// typedef struct { UINT16 VendorId; ///< Codec Vendor ID UINT16 DeviceId; ///< Codec Device ID UINT8 RevisionId; ///< Revision ID of the codec. 0xFF matches any revision. UINT8 SdiNum; ///< SDI number, 0xFF matches any SDI. UINT16 DataDwords; ///< Number of data DWORDs pointed by the codec data buffer. UINT32 Reserved; ///< Reserved for future use. Must be set to 0. } AZALIA_HEADER; /// /// Audio Azalia Verb Table structure /// typedef struct { AZALIA_HEADER Header; ///< AZALIA PCH header UINT32 *Data; ///< Pointer to the data buffer. Its length is specified in the header } AUDIO_AZALIA_VERB_TABLE; /// /// Refer to the definition of PCH_INT_PIN /// typedef enum { SiPchNoInt, ///< No Interrupt Pin SiPchIntA, SiPchIntB, SiPchIntC, SiPchIntD } SI_PCH_INT_PIN; /// /// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device. /// typedef struct { UINT8 Device; ///< Device number UINT8 Function; ///< Device function UINT8 IntX; ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN) UINT8 Irq; ///< IRQ to be set for device. } SI_PCH_DEVICE_INTERRUPT_CONFIG; #define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG 64 ///< Number of all PCH devices /** Fsp S Configuration **/ typedef struct { /** Offset 0x0020 - Logo Pointer Points to PEI Display Logo Image **/ UINT32 LogoPtr; /** Offset 0x0024 - Logo Size Size of PEI Display Logo Image **/ UINT32 LogoSize; /** Offset 0x0028 - Blt Buffer Address Address of Blt buffer **/ UINT32 BltBufferAddress; /** Offset 0x002C - Blt Buffer Size Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of EFI_GRAPHICS_OUTPUT_BLT_PIXEL) **/ UINT32 BltBufferSize; /** Offset 0x0030 - Graphics Configuration Ptr Points to VBT **/ UINT32 GraphicsConfigPtr; /** Offset 0x0034 - Enable Device 4 Enable/disable Device 4 $EN_DIS **/ UINT8 Device4Enable; /** Offset 0x0035 - Enable eMMC Controller Enable/disable eMMC Controller. $EN_DIS **/ UINT8 ScsEmmcEnabled; /** Offset 0x0036 - Enable eMMC HS400 Mode Enable eMMC HS400 Mode. $EN_DIS **/ UINT8 ScsEmmcHs400Enabled; /** Offset 0x0037 - Enable eMMC DDR50 Mode Enable eMMC DDR50 Mode. $EN_DIS **/ UINT8 ScsEmmcDdr50Enabled; /** Offset 0x0038 - Use DLL values from policy Set if FSP should use HS400 DLL values from policy $EN_DIS **/ UINT8 EmmcUseCustomDlls; /** Offset 0x0039 **/ UINT8 UnusedUpdSpace0[3]; /** Offset 0x003C - Emmc Tx CMD Delay control register value Please see Tx CMD Delay Control register definition for help **/ UINT32 EmmcTxCmdDelayRegValue; /** Offset 0x0040 - Emmc Tx DATA Delay control 1 register value Please see Tx DATA Delay control 1 register definition for help **/ UINT32 EmmcTxDataDelay1RegValue; /** Offset 0x0044 - Emmc Tx DATA Delay control 2 register value Please see Tx DATA Delay control 2 register definition for help **/ UINT32 EmmcTxDataDelay2RegValue; /** Offset 0x0048 - Emmc Rx CMD + DATA Delay control 1 register value Please see Rx CMD + DATA Delay control 1 register definition for help **/ UINT32 EmmcRxCmdDataDelay1RegValue; /** Offset 0x004C - Emmc Rx CMD + DATA Delay control 2 register value Please see Rx CMD + DATA Delay control 2 register definition for help **/ UINT32 EmmcRxCmdDataDelay2RegValue; /** Offset 0x0050 - Emmc Rx Strobe Delay control register value Please see Rx Strobe Delay control register definition for help **/ UINT32 EmmcRxStrobeDelayRegValue; /** Offset 0x0054 - Enable SdCard Controller Enable/disable SD Card Controller. $EN_DIS **/ UINT8 ScsSdCardEnabled; /** Offset 0x0055 - SdCard power enable polarity Choose SD_PWREN# polarity 0: Active low, 1: Active high **/ UINT8 SdCardPowerEnableActiveHigh; /** Offset 0x0056 - Use tuned DLL values from policy Set if FSP should use HS400 DLL values from policy $EN_DIS **/ UINT8 SdCardUseCustomDlls; /** Offset 0x0057 **/ UINT8 UnusedUpdSpace1; /** Offset 0x0058 - SdCard Tx CMD Delay control register value Please see Tx CMD Delay Control register definition for help **/ UINT32 SdCardTxCmdDelayRegValue; /** Offset 0x005C - SdCard Tx DATA Delay control 1 register value Please see Tx DATA Delay control 1 register definition for help **/ UINT32 SdCardTxDataDelay1RegValue; /** Offset 0x0060 - SdCard Tx DATA Delay control 2 register value Please see Tx DATA Delay control 2 register definition for help **/ UINT32 SdCardTxDataDelay2RegValue; /** Offset 0x0064 - SdCard Rx CMD + DATA Delay control 1 register value Please see Rx CMD + DATA Delay control 1 register definition for help **/ UINT32 SdCardRxCmdDataDelay1RegValue; /** Offset 0x0068 - SdCard Rx CMD + DATA Delay control 2 register value Please see Rx CMD + DATA Delay control 2 register definition for help **/ UINT32 SdCardRxCmdDataDelay2RegValue; /** Offset 0x006C - SdCard Power Enable Pin Mux Select Power Enable pin muxing. Refer to GPIO_*_MUXING_SDCARD_PWR_EN* for possible values. **/ UINT32 SdCardGpioPrwEnBPinMux; /** Offset 0x0070 - SdCard Power Enable Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 SdCardGpioPrwEnBPadTermination; /** Offset 0x0071 **/ UINT8 UnusedUpdSpace2[3]; /** Offset 0x0074 - SdCard Command Pin Mux Select Command pin muxing. Refer to GPIO_*_MUXING_SDCARD_CMD* for possible values. **/ UINT32 SdCardGpioCmdPinMux; /** Offset 0x0078 - SdCard Command Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 SdCardGpioCmdPadTermination; /** Offset 0x0079 **/ UINT8 UnusedUpdSpace3[3]; /** Offset 0x007C - SdCard Data Pin Mux Select Data pin muxing. Refer to GPIO_*_MUXING_SDCARD_DATAx_* for possible values. One UINT32 for each data pin [0-4] **/ UINT32 SdCardGpioDataPinMux[4]; /** Offset 0x008C - SdCard Data Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up. One byte for each data pin [0-4] **/ UINT8 SdCardGpioDataPadTermination[4]; /** Offset 0x0090 - SdCard Cdb Pin Mux Select Cdb pin muxing. Refer to GPIO_*_MUXING_SDCARD_CDB* for possible values. **/ UINT32 SdCardGpioCdbPinMux; /** Offset 0x0094 - SdCard Cdb Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 SdCardGpioCdbPadTermination; /** Offset 0x0095 **/ UINT8 UnusedUpdSpace4[3]; /** Offset 0x0098 - SdCard Clock Pin Mux Select Clock pin muxing. Refer to GPIO_*_MUXING_SDCARD_CLK* for possible values. **/ UINT32 SdCardGpioClkPinMux; /** Offset 0x009C - SdCard Clock Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 SdCardGpioClkPadTermination; /** Offset 0x009D **/ UINT8 UnusedUpdSpace5[3]; /** Offset 0x00A0 - SdCard Wp PinMux Select Wp pin muxing. Refer to GPIO_*_MUXING_SDCARD_WP* for possible values. **/ UINT32 SdCardGpioWpPinMux; /** Offset 0x00A4 - SdCard Wp Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 SdCardGpioWpPadTermination; /** Offset 0x00A5 **/ UINT8 UnusedUpdSpace6[3]; /** Offset 0x00A8 - SdCard Clock Feedback Pin Mux Select pin muxing. Refer to GPIO_*_MUXING_SDCARD_CLK_FB* for possible values. **/ UINT32 SdCardGpioClkFbPinMux; /** Offset 0x00AC - SdCard Clock Feedback Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 SdCardGpioClkFbPadTermination; /** Offset 0x00AD **/ UINT8 UnusedUpdSpace7[3]; /** Offset 0x00B0 - Emmc Command Pin Mux Select pin muxing. Refer to GPIO_*_MUXING_EMMC_CMD* for possible values. **/ UINT32 EmmcGpioCmdPinMux; /** Offset 0x00B4 - Emmc Command Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 EmmcGpioCmdPadTermination; /** Offset 0x00B5 - Emmc Data Pin Mux Select pin muxing. Refer to GPIO_*_MUXING_EMMC_DATA_x* for possible values. One UINT32 for each data pin [0-8] **/ UINT8 EmmcGpioDataPinMux[32]; /** Offset 0x00D5 - Emmc Data Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up. One byte for each data pin [0-8] **/ UINT8 EmmcGpioDataPadTermination[8]; /** Offset 0x00DD **/ UINT8 UnusedUpdSpace8[3]; /** Offset 0x00E0 - Emmc Rclk PinMux Select Rclk pin muxing. Refer to GPIO_*_MUXING_EMMC_RCLK* for possible values. **/ UINT32 EmmcGpioRclkPinMux; /** Offset 0x00E4 - Emmc Rclk Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 EmmcGpioRclkPadTermination; /** Offset 0x00E5 **/ UINT8 UnusedUpdSpace9[3]; /** Offset 0x00E8 - Emmc Clock Pin Mux Select Clock pin muxing. Refer to GPIO_*_MUXING_EMMC_CLK* for possible values. **/ UINT32 EmmcGpioClkPinMux; /** Offset 0x00EC - Emmc Clock Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 EmmcGpioClkPadTermination; /** Offset 0x00ED **/ UINT8 UnusedUpdSpace10[3]; /** Offset 0x00F0 - Emmc Resetb PinMux Select Resetb pin muxing. Refer to GPIO_*_MUXING_EMMC_RESETB* for possible values. **/ UINT32 EmmcGpioResetbPinMux; /** Offset 0x00F4 - Emmc Resetb Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 EmmcGpioResetbPadTermination; /** Offset 0x00F5 **/ UINT8 UnusedUpdSpace11[3]; /** Offset 0x00F8 - Emmc HipMon PinMux Select HipMon pin muxing. Refer to GPIO_*_MUXING_EMMC_HIP_MON* for possible values. **/ UINT32 EmmcGpioHipMonPinMux; /** Offset 0x00FC - Emmc HipMon Pad Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up **/ UINT8 EmmcGpioHipMonPadTermination; /** Offset 0x00FD - Show SPI controller Enable/disable to show SPI controller. $EN_DIS **/ UINT8 ShowSpiController; /** Offset 0x00FE **/ UINT8 UnusedUpdSpace12[2]; /** Offset 0x0100 - MicrocodeRegionBase Memory Base of Microcode Updates **/ UINT32 MicrocodeRegionBase; /** Offset 0x0104 - MicrocodeRegionSize Size of Microcode Updates **/ UINT32 MicrocodeRegionSize; /** Offset 0x0108 - SiipRegionBase Memory Base of Siip Firmware **/ UINT32 SiipRegionBase; /** Offset 0x010C - SiipRegionSize Size of Siip Firmware **/ UINT32 SiipRegionSize; /** Offset 0x0110 - Turbo Mode Enable/Disable Turbo mode. 0: disable, 1: enable $EN_DIS **/ UINT8 TurboMode; /** Offset 0x0111 - Enable SATA SALP Support Enable/disable SATA Aggressive Link Power Management. $EN_DIS **/ UINT8 SataSalpSupport; /** Offset 0x0112 - PCH Sata Port Multiplier Enable / Disable SATA Port Multiplier $EN_DIS **/ UINT8 SataPortMultiplier; /** Offset 0x0113 - Enable SATA ports Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1, and so on. **/ UINT8 SataPortsEnable[8]; /** Offset 0x011B - Enable SATA DEVSLP Feature Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each port, byte0 for port0, byte1 for port1, and so on. **/ UINT8 SataPortsDevSlp[8]; /** Offset 0x0123 - Enable USB2 ports Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for port1, and so on. **/ UINT8 PortUsb20Enable[16]; /** Offset 0x0133 - Enable USB2 ports OTG Selectively Enable/Disable USB2 OTG Mode. One byte for each port, byte0 for port0, byte1 for port1, and so on. **/ UINT8 USB20Otg[16]; /** Offset 0x0143 - Enable USB3 ports OTG Selectively Enable/Disable USB3 OTG Mode. One byte for each port, byte0 for port0, byte1 for port1, and so on. **/ UINT8 USB30Otg[10]; /** Offset 0x014D - Enable USB3 ports Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for port1, and so on. **/ UINT8 PortUsb30Enable[10]; /** Offset 0x0157 - Enable xDCI controller Enable/disable to xDCI controller. $EN_DIS **/ UINT8 XdciEnable; /** Offset 0x0158 - Address of PCH_DEVICE_INTERRUPT_CONFIG table. The address of the table of PCH_DEVICE_INTERRUPT_CONFIG. **/ UINT32 DevIntConfigPtr; /** Offset 0x015C - Number of DevIntConfig Entry Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr must not be NULL. **/ UINT8 NumOfDevIntConfig; /** Offset 0x015D - PIRQx to IRQx Map Config PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy 8259 PCI mode. **/ UINT8 PxRcConfig[8]; /** Offset 0x0165 - Select GPIO IRQ Route GPIO IRQ Select. The valid value is 14 or 15. **/ UINT8 GpioIrqRoute; /** Offset 0x0166 - Select SciIrqSelect SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only. **/ UINT8 SciIrqSelect; /** Offset 0x0167 - Select TcoIrqSelect TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23. **/ UINT8 TcoIrqSelect; /** Offset 0x0168 - Enable/Disable Tco IRQ Enable/disable TCO IRQ $EN_DIS **/ UINT8 TcoIrqEnable; /** Offset 0x0169 - PCH HDA Verb Table Entry Number Number of Entries in Verb Table. **/ UINT8 PchHdaVerbTableEntryNum; /** Offset 0x016A **/ UINT8 UnusedUpdSpace13[2]; /** Offset 0x016C - PCH HDA Verb Table Pointer Pointer to Array of pointers to Verb Table. **/ UINT32 PchHdaVerbTablePtr; /** Offset 0x0170 - PCH HDA Codec Sx Wake Capability Capability to detect wake initiated by a codec in Sx **/ UINT8 PchHdaCodecSxWakeCapability; /** Offset 0x0171 - Enable SATA Enable/disable SATA controller. $EN_DIS **/ UINT8 SataEnable; /** Offset 0x0172 - SATA Mode Select SATA controller working mode. 0:AHCI, 1:RAID **/ UINT8 SataMode; /** Offset 0x0173 - SPIn Device Mode Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden **/ UINT8 SerialIoSpiMode[7]; /** Offset 0x017A - SPI Chip Select Polarity Sets polarity for each chip Select. Available options: 0:SerialIoSpiCsActiveLow, 1:SerialIoSpiCsActiveHigh **/ UINT8 SerialIoSpiCsPolarity[14]; /** Offset 0x0188 - SPI Chip Select Enable 0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled **/ UINT8 SerialIoSpiCsEnable[14]; /** Offset 0x0196 - SPIn Default Chip Select Output Sets Default CS as Output. N represents controller index: SPI0, SPI1, ... Available options: 0:CS0, 1:CS1 **/ UINT8 SerialIoSpiDefaultCsOutput[7]; /** Offset 0x019D - SPIn Default Chip Select Mode HW/SW Sets Default CS Mode Hardware or Software. N represents controller index: SPI0, SPI1, ... Available options: 0:HW, 1:SW **/ UINT8 SerialIoSpiCsMode[7]; /** Offset 0x01A4 - SPIn Default Chip Select State Low/High Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ... Available options: 0:Low, 1:High **/ UINT8 SerialIoSpiCsState[7]; /** Offset 0x01AB - SPIn Master Input Slave Output Enable/Disable 0:Disabled, 1:Enabled. Sets Native Mode for SPIx MISO GPIO if it is Enabled **/ UINT8 SerialIoSpiMisoEnable[3]; /** Offset 0x01AE - SPIn Delayed Rx Clock setting 00:As-is, 01:Internal, 10:NegEdge Tx Clock, 11:NegEdge Delayed Rx Clk. Configure Delayed Rx Clock **/ UINT8 SerialIoSpiDelayRxClk[3]; /** Offset 0x01B1 - UARTn Device Mode Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom, 4:SerialIoUartSkipInit **/ UINT8 SerialIoUartMode[7]; /** Offset 0x01B8 - Default BaudRate for each Serial IO UART Set default BaudRate Supported from 0 - default to 6000000 **/ UINT32 SerialIoUartBaudRate[7]; /** Offset 0x01D4 - Default ParityType for each Serial IO UART Set default Parity. 0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity **/ UINT8 SerialIoUartParity[7]; /** Offset 0x01DB - Default DataBits for each Serial IO UART Set default word length. 0: Default, 5,6,7,8 **/ UINT8 SerialIoUartDataBits[7]; /** Offset 0x01E2 - Default StopBits for each Serial IO UART Set default stop bits. 0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3: TwoStopBits **/ UINT8 SerialIoUartStopBits[7]; /** Offset 0x01E9 - Power Gating mode for each Serial IO UART that works in COM mode Set Power Gating. 0: Disabled, 1: Enabled, 2: Auto **/ UINT8 SerialIoUartPowerGating[7]; /** Offset 0x01F0 - Enable Dma for each Serial IO UART that supports it Set DMA/PIO mode. 0: Disabled, 1: Enabled **/ UINT8 SerialIoUartDmaEnable[7]; /** Offset 0x01F7 - Enables UART hardware flow control, CTS and RTS lines Enables UART hardware flow control, CTS and RTS lines. **/ UINT8 SerialIoUartAutoFlow[7]; /** Offset 0x01FE **/ UINT8 UnusedUpdSpace14[2]; /** Offset 0x0200 - SerialIoUartRtsPinMuxPolicy Select SerialIo Uart Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS* for possible values. **/ UINT32 SerialIoUartRtsPinMuxPolicy[7]; /** Offset 0x021C - SerialIoUartCtsPinMuxPolicy Select SerialIo Uart Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS* for possible values. **/ UINT32 SerialIoUartCtsPinMuxPolicy[7]; /** Offset 0x0238 - SerialIoUartRxPinMuxPolicy Select SerialIo Uart Rx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RX* for possible values. **/ UINT32 SerialIoUartRxPinMuxPolicy[7]; /** Offset 0x0254 - SerialIoUartTxPinMuxPolicy Select SerialIo Uart Tx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_TX* for possible values. **/ UINT32 SerialIoUartTxPinMuxPolicy[7]; /** Offset 0x0270 - UART Number For Debug Purpose UART number for debug purpose. 0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5, 6:UART6. Note: If UART0 is selected as CNVi BT Core interface, it cannot be used for debug purpose. 0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5, 6:UART6 **/ UINT8 SerialIoDebugUartNumber; /** Offset 0x0271 - Serial IO UART DBG2 table Enable or disable Serial Io UART DBG2 table, default is Disable; 0: Disable; 1: Enable. **/ UINT8 SerialIoUartDbg2[7]; /** Offset 0x0278 - I2Cn Device Mode Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden **/ UINT8 SerialIoI2cMode[8]; /** Offset 0x0280 - Serial IO I2C SDA Pin Muxing Select SerialIo I2c Sda pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SDA* for possible values. **/ UINT32 PchSerialIoI2cSdaPinMux[8]; /** Offset 0x02A0 - Serial IO I2C SCL Pin Muxing Select SerialIo I2c Scl pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SCL* for possible values. **/ UINT32 PchSerialIoI2cSclPinMux[8]; /** Offset 0x02C0 - PCH SerialIo I2C Pads Termination 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, 0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,... pads termination respectively. One byte for each controller, byte0 for I2C0, byte1 for I2C1, and so on. 0x1:None, 0x13:1kOhm WPU, 0x15:5kOhm WPU, 0x19:20kOhm WPU **/ UINT8 PchSerialIoI2cPadsTermination[8]; /** Offset 0x02C8 - USB Per Port HS Preemphasis Bias USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV, 100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port. **/ UINT8 Usb2PhyPetxiset[16]; /** Offset 0x02D8 - USB Per Port HS Transmitter Bias USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV, 100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port. **/ UINT8 Usb2PhyTxiset[16]; /** Offset 0x02E8 - USB Per Port HS Transmitter Emphasis USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON, 10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port. **/ UINT8 Usb2PhyPredeemp[16]; /** Offset 0x02F8 - USB Per Port Half Bit Pre-emphasis USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis. One byte for each port. **/ UINT8 Usb2PhyPehalfbit[16]; /** Offset 0x0308 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value in arrary can be between 0-1. One byte for each port. **/ UINT8 Usb3HsioTxDeEmphEnable[10]; /** Offset 0x0312 - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16], Default = 29h (approximately -3.5dB De-Emphasis). One byte for each port. **/ UINT8 Usb3HsioTxDeEmph[10]; /** Offset 0x031C - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value in arrary can be between 0-1. One byte for each port. **/ UINT8 Usb3HsioTxDownscaleAmpEnable[10]; /** Offset 0x0326 - USB 3.0 TX Output Downscale Amplitude Adjustment USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], Default = 00h. One byte for each port. **/ UINT8 Usb3HsioTxDownscaleAmp[10]; /** Offset 0x0330 **/ UINT8 PchUsb3HsioCtrlAdaptOffsetCfgEnable[10]; /** Offset 0x033A **/ UINT8 PchUsb3HsioFilterSelNEnable[10]; /** Offset 0x0344 **/ UINT8 PchUsb3HsioFilterSelPEnable[10]; /** Offset 0x034E **/ UINT8 PchUsb3HsioOlfpsCfgPullUpDwnResEnable[10]; /** Offset 0x0358 **/ UINT8 PchUsb3HsioCtrlAdaptOffsetCfg[10]; /** Offset 0x0362 **/ UINT8 PchUsb3HsioOlfpsCfgPullUpDwnRes[10]; /** Offset 0x036C **/ UINT8 PchUsb3HsioFilterSelN[10]; /** Offset 0x0376 **/ UINT8 PchUsb3HsioFilterSelP[10]; /** Offset 0x0380 - Enable LAN Enable/disable LAN controller. $EN_DIS **/ UINT8 PchLanEnable; /** Offset 0x0381 - Enable PCH TSN Enable/disable TSN on the PCH. $EN_DIS **/ UINT8 PchTsnEnable; /** Offset 0x0382 - PCH TSN Multi VC Enable Enable/Disable PCH TSN GBE Multiple Virtual Channel $EN_DIS **/ UINT8 PchTsnGbeMultiVcEnable; /** Offset 0x0383 - PCH TSN Link Speed Set PCH TSN Link Speed. 0: 24Mhz 2.5Gbps, 1: 24Mhz 1Gbps, 2: 38.4Mhz 2.5Gbps, 3: 38.4Mhz 1Gbps **/ UINT8 PchTsnGbeLinkSpeed; /** Offset 0x0384 - PCH TSN SGMII Support Enable/disable SGMII support $EN_DIS **/ UINT8 PchTsnGbeSgmiiEnable; /** Offset 0x0385 - PSE TSN Multi VC Enable Enable/Disable PSE TSN GBE Multiple Virtual Channel $EN_DIS **/ UINT8 PseTsnGbeMultiVcEnable[2]; /** Offset 0x0387 - PSE TSN Link Speed Set TSN Link Speed. 0: 24Mhz 2.5Gbps, 1: 24Mhz 1Gbps, 2: 38.4Mhz 2.5Gbps, 3: 38.4Mhz 1Gbps **/ UINT8 PseTsnGbeLinkSpeed[2]; /** Offset 0x0389 - PSE TSN SGMII Support Enable/disable SGMII support $EN_DIS **/ UINT8 PseTsnGbeSgmiiEnable[2]; /** Offset 0x038B - PSE TSN Phy Interface Type Set PSE TSN Phy Interface Type 0: Not Connected, 1: RGMII, 2: SGMII, 3:SGMII+ **/ UINT8 PseTsnGbePhyInterfaceType[2]; /** Offset 0x038D **/ UINT8 UnusedUpdSpace15[3]; /** Offset 0x0390 - Tsn Mac Address Sub Region Base Base address of TSN MAC Address Sub Region **/ UINT32 TsnMacAddrBase; /** Offset 0x0394 - Tsn Mac Address Sub Region Size Size of TSN MAC Address Sub Region **/ UINT32 TsnMacAddrSize; /** Offset 0x0398 - PSE Tsn Ip Config Sub Region Base Base address of PSE TSN IP Config Sub Region **/ UINT32 PseTsnIpConfigBase; /** Offset 0x039C - PSE Tsn Ip Config Sub Region Size Size of PSE TSN IP Config Sub Region **/ UINT32 PseTsnIpConfigSize; /** Offset 0x03A0 - Tsn Config Sub Region Base Base address of TSN Config Sub Region **/ UINT32 TsnConfigBase; /** Offset 0x03A4 - Tsn Config Sub Region Size Size of TSN Config Sub Region **/ UINT32 TsnConfigSize; /** Offset 0x03A8 - PSE GBE0 DLL OVERRIDE Enable/Disable PSE GBE DLL OVERRIDE $EN_DIS **/ UINT8 PseGbeDllOverride[2]; /** Offset 0x03AA - PSE GBE TX_Delay PSE GBE TX_Delay configuration. **/ UINT8 PseGbeTxDelay[2]; /** Offset 0x03AC - PCIe PTM enable/disable Enable/disable Precision Time Measurement for PCIE Root Ports. **/ UINT8 PciePtm[24]; /** Offset 0x03C4 - PCIe DPC enable/disable Enable/disable Downstream Port Containment for PCIE Root Ports. **/ UINT8 PcieDpc[24]; /** Offset 0x03DC - PCIe DPC extensions enable/disable Enable/disable Downstream Port Containment Extensions for PCIE Root Ports. **/ UINT8 PcieEdpc[24]; /** Offset 0x03F4 - USB PDO Programming Enable/disable PDO programming for USB in PEI phase. Disabling will allow for programming during later phase. 1: enable, 0: disable $EN_DIS **/ UINT8 UsbPdoProgramming; /** Offset 0x03F5 **/ UINT8 UnusedUpdSpace16[3]; /** Offset 0x03F8 - Power button debounce configuration Debounce time for PWRBTN in microseconds. For values not supported by HW, they will be rounded down to closest supported on. 0: disable, 250-1024000us: supported range **/ UINT32 PmcPowerButtonDebounce; /** Offset 0x03FC - PCH eSPI Master and Slave BME enabled PCH eSPI Master and Slave BME enabled $EN_DIS **/ UINT8 PchEspiBmeMasterSlaveEnabled; /** Offset 0x03FD - PCH SATA use RST Legacy OROM Use PCH SATA RST Legacy OROM when CSM is Enabled $EN_DIS **/ UINT8 SataRstLegacyOrom; /** Offset 0x03FE - Mask to enable the usage of external V1p05 VR rail in specific S0ix or Sx states Enable External V1P05 Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5 **/ UINT8 PchFivrExtV1p05RailEnabledStates; /** Offset 0x03FF - Mask to enable the platform configuration of external V1p05 VR rail External V1P05 Rail Supported Configuration **/ UINT8 PchFivrExtV1p05RailSupportedVoltageStates; /** Offset 0x0400 - External V1P05 Voltage Value that will be used in S0i2/S0i3 states Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...) **/ UINT16 PchFivrExtV1p05RailVoltage; /** Offset 0x0402 - External V1P05 Icc Max Value Granularity of this setting is 1mA and maximal possible value is 200mA **/ UINT8 PchFivrExtV1p05RailIccMax; /** Offset 0x0403 - Mask to enable the usage of external Vnn VR rail in specific S0ix or Sx states Enable External Vnn Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5 **/ UINT8 PchFivrExtVnnRailEnabledStates; /** Offset 0x0404 - Mask to enable the platform configuration of external Vnn VR rail External Vnn Rail Supported Configuration **/ UINT8 PchFivrExtVnnRailSupportedVoltageStates; /** Offset 0x0405 **/ UINT8 UnusedUpdSpace17; /** Offset 0x0406 - External Vnn Voltage Value that will be used in S0ix/Sx states Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...), Default is set to 420 **/ UINT16 PchFivrExtVnnRailVoltage; /** Offset 0x0408 - External Vnn Icc Max Value that will be used in S0ix/Sx states Granularity of this setting is 1mA and maximal possible value is 200mA **/ UINT8 PchFivrExtVnnRailIccMax; /** Offset 0x0409 - Mask to enable the usage of external Vnn VR rail in Sx states Use only if Ext Vnn Rail config is different in Sx. Enable External Vnn Rail in Sx: BIT0-1:Reserved, BIT2:S3, BIT3:S4, BIT5:S5 **/ UINT8 PchFivrExtVnnRailSxEnabledStates; /** Offset 0x040A - External Vnn Voltage Value that will be used in Sx states Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...) **/ UINT16 PchFivrExtVnnRailSxVoltage; /** Offset 0x040C - External Vnn Icc Max Value that will be used in Sx states Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting is 1mA and maximal possible value is 200mA **/ UINT8 PchFivrExtVnnRailSxIccMax; /** Offset 0x040D - Transition time in microseconds from Low Current Mode Voltage to High Current Mode Voltage This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX to low current mode voltage. **/ UINT8 PchFivrVccinAuxLowToHighCurModeVolTranTime; /** Offset 0x040E - Transition time in microseconds from Retention Mode Voltage to High Current Mode Voltage This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX to retention mode voltage. **/ UINT8 PchFivrVccinAuxRetToHighCurModeVolTranTime; /** Offset 0x040F - Transition time in microseconds from Retention Mode Voltage to Low Current Mode Voltage This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX to retention mode voltage. **/ UINT8 PchFivrVccinAuxRetToLowCurModeVolTranTime; /** Offset 0x0410 - Transition time in microseconds from Off (0V) to High Current Mode Voltage This field has 1us resolution. When value is 0 Transition to 0V is disabled. **/ UINT16 PchFivrVccinAuxOffToHighCurModeVolTranTime; /** Offset 0x0412 **/ UINT8 UnusedUpdSpace18[2]; /** Offset 0x0414 - Trace Hub Memory Base If Trace Hub is enabled and trace to memory is desired, BootLoader needs to allocate trace hub memory as reserved and uncacheable, set the base to ensure Trace Hub memory is configured properly. **/ UINT32 TraceHubMemBase; /** Offset 0x0418 - PMC Debug Message Enable When Enabled, PMC HW will send debug messages to trace hub; When Disabled, PMC HW will never send debug meesages to trace hub. Noted: When Enabled, may not enter S0ix $EN_DIS **/ UINT8 PmcDbgMsgEn; /** Offset 0x0419 **/ UINT8 UnusedUpdSpace19[3]; /** Offset 0x041C - Pointer of ChipsetInit Binary ChipsetInit Binary Pointer. **/ UINT32 ChipsetInitBinPtr; /** Offset 0x0420 - Length of ChipsetInit Binary ChipsetInit Binary Length. **/ UINT32 ChipsetInitBinLen; /** Offset 0x0424 - ChipsetInit Sync Enable Enable/Disable. 0: Disable, 1: Enable **/ UINT8 ChipsetInitSyncEnable; /** Offset 0x0425 - FIVR Dynamic Power Management Enable/Disable FIVR Dynamic Power Management. $EN_DIS **/ UINT8 PchFivrDynPm; /** Offset 0x0426 - External V1P05 Icc Max Value Granularity of this setting is 1mA and maximal possible value is 500mA **/ UINT16 PchFivrExtV1p05RailIccMaximum; /** Offset 0x0428 - External Vnn Icc Max Value that will be used in S0ix/Sx states Granularity of this setting is 1mA and maximal possible value is 500mA **/ UINT16 PchFivrExtVnnRailIccMaximum; /** Offset 0x042A - External Vnn Icc Max Value that will be used in Sx states Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting is 1mA and maximal possible value is 500mA **/ UINT16 PchFivrExtVnnRailSxIccMaximum; /** Offset 0x042C - PCH eSPI Link Configuration Lock (SBLCL) Enable/Disable lock of communication through SET_CONFIG/GET_CONFIG to eSPI slaves addresseses from range 0x0 - 0x7FF $EN_DIS **/ UINT8 PchEspiLockLinkConfiguration; /** Offset 0x042D - Extented BIOS Direct Read Decode enable Enable/Disable access to bigger than 16MB BIOS Region through Direct Memory Reads. 0: disabled (default), 1: enabled $EN_DIS **/ UINT8 PchSpiExtendedBiosDecodeRangeEnable; /** Offset 0x042E - PchPostMemRsvd Reserved for PCH Post-Mem $EN_DIS **/ UINT8 PchPostMemRsvd[11]; /** Offset 0x0439 **/ UINT8 UnusedUpdSpace20[3]; /** Offset 0x043C - Extended BIOS Direct Read Decode Range base Bits of 31:16 of a memory address that'll be a base for Extended BIOS Direct Read Decode. **/ UINT32 PchSpiExtendedBiosDecodeRangeBase; /** Offset 0x0440 - Extended BIOS Direct Read Decode Range limit Bits of 31:16 of a memory address that'll be a limit for Extended BIOS Direct Read Decode. **/ UINT32 PchSpiExtendedBiosDecodeRangeLimit; /** Offset 0x0444 - CNVi Configuration This option allows for automatic detection of Connectivity Solution. [Auto Detection] assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi. 0:Disable, 1:Auto **/ UINT8 CnviMode; /** Offset 0x0445 - CNVi BT Core Enable/Disable CNVi BT Core, Default is ENABLE. 0: DISABLE, 1: ENABLE $EN_DIS **/ UINT8 CnviBtCore; /** Offset 0x0446 - CNVi BT Audio Offload Enable/Disable BT Audio Offload, Default is DISABLE. 0: DISABLE, 1: ENABLE $EN_DIS **/ UINT8 CnviBtAudioOffload; /** Offset 0x0447 **/ UINT8 UnusedUpdSpace21; /** Offset 0x0448 - CNVi RF_RESET pin muxing Select CNVi RF_RESET# pin depending on board routing. TGP-LP: GPP_A8 = 0x2942E408(default) or GPP_F4 = 0x194BE404. TGP-H: 0. TGP-K: 0. Refer to GPIO_*_MUXING_CNVI_RF_RESET_* in GpioPins*.h. **/ UINT32 CnviRfResetPinMux; /** Offset 0x044C - CNVi CLKREQ pin muxing Select CNVi CLKREQ pin depending on board routing. TGP-LP: GPP_A9 = 0x3942E609(default) or GPP_F5 = 0x394BE605. TGP-H: 0. TGP-K: 0. Refer to GPIO_*_MUXING_CNVI_MODEM_CLKREQ_* in GpioPins*.h. **/ UINT32 CnviClkreqPinMux; /** Offset 0x0450 - Enable Host C10 reporting through eSPI Enable/disable Host C10 reporting to Slave via eSPI Virtual Wire. $EN_DIS **/ UINT8 PchEspiHostC10ReportEnable; /** Offset 0x0451 - PCH USB2 PHY Power Gating enable 1: Will enable USB2 PHY SUS Well Power Gating, 0: Will not enable PG of USB2 PHY Sus Well PG $EN_DIS **/ UINT8 PmcUsb2PhySusPgEnable; /** Offset 0x0452 - PCH USB OverCurrent mapping enable 1: Will program USB OC pin mapping in xHCI controller memory, 0: Will clear OC pin mapping allow for NOA usage of OC pins $EN_DIS **/ UINT8 PchUsbOverCurrentEnable; /** Offset 0x0453 - Espi Lgmr Memory Range decode This option enables or disables espi lgmr $EN_DIS **/ UINT8 PchEspiLgmrEnable; /** Offset 0x0454 - External V1P05 Control Ramp Timer value Hold off time to be used when changing the v1p05_ctrl for external bypass value in us **/ UINT8 PchFivrExtV1p05RailCtrlRampTmr; /** Offset 0x0455 - External VNN Control Ramp Timer value Hold off time to be used when changing the vnn_ctrl for external bypass value in us **/ UINT8 PchFivrExtVnnRailCtrlRampTmr; /** Offset 0x0456 - HECI3 state The HECI3 state from Mbp for reference in S3 path or when MbpHob is not installed. 0: disable, 1: enable $EN_DIS **/ UINT8 Heci3Enabled; /** Offset 0x0457 - PCHHOT# pin Enable PCHHOT# pin assertion when temperature is higher than PchHotLevel. 0: disable, 1: enable $EN_DIS **/ UINT8 PchHotEnable; /** Offset 0x0458 - SATA LED SATA LED indicating SATA controller activity. 0: disable, 1: enable $EN_DIS **/ UINT8 SataLedEnable; /** Offset 0x0459 - VRAlert# Pin When VRAlert# feature pin is enabled and its state is '0', the PMC requests throttling to a T3 Tstate to the PCH throttling unit.. 0: disable, 1: enable $EN_DIS **/ UINT8 PchPmVrAlert; /** Offset 0x045A - AMT Switch Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality. $EN_DIS **/ UINT8 AmtEnabled; /** Offset 0x045B - WatchDog Timer Switch Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer. Setting is invalid if AmtEnabled is 0. $EN_DIS **/ UINT8 WatchDogEnabled; /** Offset 0x045C - Manageability Mode set by Mebx Enable/Disable. 0: Disable, 1: enable, Enable or disable Manageability Mode. $EN_DIS **/ UINT8 ManageabilityMode; /** Offset 0x045D - PET Progress Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive PET Events. Setting is invalid if AmtEnabled is 0. $EN_DIS **/ UINT8 FwProgress; /** Offset 0x045E - SOL Switch Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx. Setting is invalid if AmtEnabled is 0. $EN_DIS **/ UINT8 AmtSolEnabled; /** Offset 0x045F **/ UINT8 UnusedUpdSpace22; /** Offset 0x0460 - OS Timer 16 bits Value, Set OS watchdog timer. Setting is invalid if AmtEnabled is 0. **/ UINT16 WatchDogTimerOs; /** Offset 0x0462 - BIOS Timer 16 bits Value, Set BIOS watchdog timer. Setting is invalid if AmtEnabled is 0. **/ UINT16 WatchDogTimerBios; /** Offset 0x0464 - Remote Assistance Trigger Availablilty Enable/Disable. 0: Disable, 1: enable, Remote Assistance enable/disable state by Mebx. $EN_DIS **/ UINT8 RemoteAssistance; /** Offset 0x0465 - KVM Switch Enable/Disable. 0: Disable, 1: enable, KVM enable/disable state by Mebx. Setting is invalid if AmtEnabled is 0. $EN_DIS **/ UINT8 AmtKvmEnabled; /** Offset 0x0466 - KVM Switch Enable/Disable. 0: Disable, 1: enable, KVM enable/disable state by Mebx. $EN_DIS **/ UINT8 ForcMebxSyncUp; /** Offset 0x0467 - PCH PCIe root port connection type 0: built-in device, 1:slot **/ UINT8 PcieRpSlotImplemented[24]; /** Offset 0x047F - PCIE RP Access Control Services Extended Capability Enable/Disable PCIE RP Access Control Services Extended Capability **/ UINT8 PcieRpAcsEnabled[24]; /** Offset 0x0497 - PCIE RP Clock Power Management Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal can still be controlled by L1 PM substates mechanism **/ UINT8 PcieRpEnableCpm[24]; /** Offset 0x04AF - PCIE RP Multi VC Enabled Enable/Disable PCIE RP Multiple Virtual Channels **/ UINT8 PcieRpMultiVcEnabled[24]; /** Offset 0x04C7 - PCIE RP VC1 to TC Mapping PCIE RP Virtual Channel 1 to Traffic Class mapping **/ UINT8 PcieRpVc1TcMap[24]; /** Offset 0x04DF **/ UINT8 UnusedUpdSpace23[1]; /** Offset 0x04E0 - PCIE RP Detect Timeout Ms The number of milliseconds within 0~65535 in reference code will wait for link to exit Detect state for enabled ports before assuming there is no device and potentially disabling the port. **/ UINT16 PcieRpDetectTimeoutMs[24]; /** Offset 0x0510 - ModPHY SUS Power Domain Dynamic Gating Enable/Disable ModPHY SUS Power Domain Dynamic Gating. Setting not supported on PCH-H. 0: disable, 1: enable $EN_DIS **/ UINT8 PmcModPhySusPgEnable; /** Offset 0x0511 - V1p05-PHY supply external FET control Enable/Disable control using EXT_PWR_GATE# pin of external FET to power gate v1p05-PHY supply. 0: disable, 1: enable $EN_DIS **/ UINT8 PmcV1p05PhyExtFetControlEn; /** Offset 0x0512 - V1p05-IS supply external FET control Enable/Disable control using EXT_PWR_GATE2# pin of external FET to power gate v1p05-IS supply. 0: disable, 1: enable $EN_DIS **/ UINT8 PmcV1p05IsExtFetControlEn; /** Offset 0x0513 - Enable/Disable PavpEnable Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable $EN_DIS **/ UINT8 PavpEnable; /** Offset 0x0514 - CdClock Frequency selection 0 (Default) Auto (Max based on reference clock frequency), 0: 307.2, 1: 312 Mhz, 2: 552 Mhz, 3: 556.8 Mhz, 4: 648 Mhz, 5: 652.8 Mhz 0xFF: Auto (Max based on reference clock frequency), 0: 307.2, 1: 312 Mhz, 2: 552 Mhz, 3: 556.8 Mhz, 4: 648 Mhz, 5: 652.8 Mhz **/ UINT8 CdClock; /** Offset 0x0515 - Enable/Disable PeiGraphicsPeimInit Enable(Default): Enable PeiGraphicsPeimInit, Disable: Disable PeiGraphicsPeimInit $EN_DIS **/ UINT8 PeiGraphicsPeimInit; /** Offset 0x0516 - Enable D3 Hot in TCSS This policy will enable/disable D3 hot support in IOM $EN_DIS **/ UINT8 D3HotEnable; /** Offset 0x0517 - Enable or disable GNA device 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 GnaEnable; /** Offset 0x0518 - Enable or disable HPD of DDI port-A device 0=Disabled,1(Default)=eDP, 2=MIPI DSI, 0:Disabled, 1:eDP, 2:MIPI DSI **/ UINT8 DdiPortAConfig; /** Offset 0x0519 - Enable or disable HPD of DDI port-B device 1(Default)=DP, 2=MIPI DSI, 3=HDMI 1:DP, 2:MIPI DSI, 3:HDMI **/ UINT8 DdiPortBConfig; /** Offset 0x051A - Enable or disable HPD of DDI port-C device 1(Default)= HDMI, 2=DP 1:HDMI, 2:DP **/ UINT8 DdiPortCConfig; /** Offset 0x051B - Enable or disable HPD of DDI port A 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPortAHpd; /** Offset 0x051C - Enable or disable HPD of DDI port B 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPortBHpd; /** Offset 0x051D - Enable or disable HPD of DDI port C 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPortCHpd; /** Offset 0x051E - Enable or disable HPD of DDI port 1 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPort1Hpd; /** Offset 0x051F - Enable or disable HPD of DDI port 2 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPort2Hpd; /** Offset 0x0520 - Enable or disable HPD of DDI port 3 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPort3Hpd; /** Offset 0x0521 - Enable or disable HPD of DDI port 4 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPort4Hpd; /** Offset 0x0522 - Enable or disable DDC of DDI port A 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPortADdc; /** Offset 0x0523 - Enable or disable DDC of DDI port B 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPortBDdc; /** Offset 0x0524 - Enable or disable DDC of DDI port C 0=Disable, 1(Default)=Enable $EN_DIS **/ UINT8 DdiPortCDdc; /** Offset 0x0525 - Enable DDC setting of DDI Port 1 0=Disable, 1=DDC(Default) 0: Disable, 1: DDC **/ UINT8 DdiPort1Ddc; /** Offset 0x0526 - Enable DDC setting of DDI Port 2 0=Disable, 1=DDC(Default) 0: Disable, 1: DDC **/ UINT8 DdiPort2Ddc; /** Offset 0x0527 - Enable DDC setting of DDI Port 3 0=Disable, 1=DDC(Default) 0: Disable, 1: DDC **/ UINT8 DdiPort3Ddc; /** Offset 0x0528 - Enable DDC setting of DDI Port 4 0=Disable, 1=DDC(Default) 0: Disable, 1: DDC **/ UINT8 DdiPort4Ddc; /** Offset 0x0529 **/ UINT8 UnusedUpdSpace24[3]; /** Offset 0x052C - TypeC port GPIO setting GPIO Ping number for Type C Aux Oritation setting, use the GpioPad that is defined in GpioPinsXXXH.h and GpioPinsXXXLp.h as argument.(XXX is platform name, Ex: Ehl = ElkhartLake) **/ UINT32 IomTypeCPortPadCfg[8]; /** Offset 0x054C - CPU USB3 Port Over Current Pin Describe the specific over current pin number of USBC Port N. **/ UINT8 CpuUsb3OverCurrentPin[8]; /** Offset 0x0554 - Enable D3 Cold in TCSS This policy will enable/disable D3 cold support in IOM $EN_DIS **/ UINT8 D3ColdEnable; /** Offset 0x0555 - PchPostMemRsvd Reserved for PCH Post-Mem $EN_DIS **/ UINT8 SaPostMemRsvd[8]; /** Offset 0x055D - Enable VMD controller Enable/disable to VMD controller.0: Disable(Default); 1: Enable $EN_DIS **/ UINT8 VmdEnable; /** Offset 0x055E - Enable VMD portA Support Enable/disable to VMD portA Support. $EN_DIS **/ UINT8 VmdPortA; /** Offset 0x055F - Enable VMD portB Support Enable/disable to VMD portB Support. $EN_DIS **/ UINT8 VmdPortB; /** Offset 0x0560 - Enable VMD portC Support Enable/disable to VMD portC Support. $EN_DIS **/ UINT8 VmdPortC; /** Offset 0x0561 - Enable VMD portD Support Enable/disable to VMD portD Support. $EN_DIS **/ UINT8 VmdPortD; /** Offset 0x0562 - VMD Config Bar size Set The VMD Config Bar Size. **/ UINT8 VmdCfgBarSz; /** Offset 0x0563 - VMD Config Bar Attributes 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH(Default) 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH **/ UINT8 VmdCfgBarAttr; /** Offset 0x0564 - VMD Mem Bar1 size Set The VMD Mem Bar1 Size. **/ UINT8 VmdMemBarSz1; /** Offset 0x0565 - VMD Mem Bar1 Attributes 0: VMD_32BIT_NONPREFETCH(Default), 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH **/ UINT8 VmdMemBar1Attr; /** Offset 0x0566 - VMD Mem Bar2 size Set The VMD Mem Bar2 Size. **/ UINT8 VmdMemBarSz2; /** Offset 0x0567 - VMD Mem Bar2 Attributes 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH(Default), 2: VMD_64BIT_PREFETCH 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH **/ UINT8 VmdMemBar2Attr; /** Offset 0x0568 - Enable/Disable PMC-PD Solution This policy will enable/disable PMC-PD Solution vs EC-TCPC Solution $EN_DIS **/ UINT8 PmcPdEnable; /** Offset 0x0569 **/ UINT8 UnusedUpdSpace25; /** Offset 0x056A - TCSS Aux Orientation Override Enable Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides **/ UINT16 TcssAuxOri; /** Offset 0x056C - TCSS HSL Orientation Override Enable Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides **/ UINT16 TcssHslOri; /** Offset 0x056E - USB override in IOM This policy will enable/disable USB Connect override in IOM $EN_DIS **/ UINT8 UsbOverride; /** Offset 0x056F - TCSS USB Port Enable Bits 0, 1, ... max Type C port control enables **/ UINT8 UsbTcPortEn; /** Offset 0x0570 - ITBT Root Port Enable ITBT Root Port Enable, 0:Disable, 1:Enable 0:Disable, 1:Enable **/ UINT8 ITbtPcieRootPortEn[4]; /** Offset 0x0574 - ITBTForcePowerOn Timeout value ITBTForcePowerOn value. Specified increment values in miliseconds. Range is 0-1000. 100 = 100 ms. **/ UINT16 ITbtForcePowerOnTimeoutInMs; /** Offset 0x0576 - ITbtConnectTopology Timeout value ITbtConnectTopologyTimeout value. Specified increment values in miliseconds. Range is 0-10000. 100 = 100 ms. **/ UINT16 ITbtConnectTopologyTimeoutInMs; /** Offset 0x0578 - VCCST request for IOM This policy will enable/disable VCCST and also decides if message would be replayed in S4/S5 $EN_DIS **/ UINT8 VccSt; /** Offset 0x0579 **/ UINT8 UnusedUpdSpace26[1]; /** Offset 0x057A - ITBT DMA LTR TCSS DMA1, DMA2 LTR value **/ UINT16 ITbtDmaLtr[2]; /** Offset 0x057E - Enable/Disable CrashLog Enable(Default): Enable CPU CrashLog, Disable: Disable CPU CrashLog $EN_DIS **/ UINT8 CpuCrashLogEnable; /** Offset 0x057F - Enable/Disable PTM This policy will enable/disable Precision Time Measurement for TCSS PCIe Root Ports $EN_DIS **/ UINT8 PtmEnabled[4]; /** Offset 0x0583 - PCIE RP Ltr Enable Latency Tolerance Reporting Mechanism. **/ UINT8 SaPcieItbtRpLtrEnable[4]; /** Offset 0x0587 - PCIE RP Snoop Latency Override Mode Latency Tolerance Reporting, Snoop Latency Override Mode. **/ UINT8 SaPcieItbtRpSnoopLatencyOverrideMode[4]; /** Offset 0x058B - PCIE RP Snoop Latency Override Multiplier Latency Tolerance Reporting, Snoop Latency Override Multiplier. **/ UINT8 SaPcieItbtRpSnoopLatencyOverrideMultiplier[4]; /** Offset 0x058F **/ UINT8 UnusedUpdSpace27[1]; /** Offset 0x0590 - PCIE RP Snoop Latency Override Value Latency Tolerance Reporting, Snoop Latency Override Value. **/ UINT16 SaPcieItbtRpSnoopLatencyOverrideValue[4]; /** Offset 0x0598 - PCIE RP Non Snoop Latency Override Mode Latency Tolerance Reporting, Non-Snoop Latency Override Mode. **/ UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMode[4]; /** Offset 0x059C - PCIE RP Non Snoop Latency Override Multiplier Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier. **/ UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMultiplier[4]; /** Offset 0x05A0 - PCIE RP Non Snoop Latency Override Value Latency Tolerance Reporting, Non-Snoop Latency Override Value. **/ UINT16 SaPcieItbtRpNonSnoopLatencyOverrideValue[4]; /** Offset 0x05A8 - Force LTR Override Force LTR Override. **/ UINT8 SaPcieItbtRpForceLtrOverride[4]; /** Offset 0x05AC - PCIE RP Ltr Config Lock 0: Disable; 1: Enable. **/ UINT8 SaPcieItbtRpLtrConfigLock[4]; /** Offset 0x05B0 - Advanced Encryption Standard (AES) feature Enable or Disable Advanced Encryption Standard (AES) feature; 0: Disable; 1: Enable $EN_DIS **/ UINT8 AesEnable; /** Offset 0x05B1 - Power State 3 enable/disable PCODE MMIO Mailbox: Power State 3 enable/disable; 0: Disable; 1: Enable. For all VR Indexes **/ UINT8 Psi3Enable[5]; /** Offset 0x05B6 - Power State 4 enable/disable PCODE MMIO Mailbox: Power State 4 enable/disable; 0: Disable; 1: Enable.For all VR Indexes **/ UINT8 Psi4Enable[5]; /** Offset 0x05BB **/ UINT8 UnusedUpdSpace28[1]; /** Offset 0x05BC - Imon slope correction PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values. Range is 0-200. 125 = 1.25. 0: Auto.For all VR Indexes **/ UINT16 ImonSlope[5]; /** Offset 0x05C6 - Imon offset correction PCODE MMIO Mailbox: Imon offset correction. Value is a 2's complement signed integer. Units 1/1000, Range 0-63999. For an offset = 12.580, use 12580. 0: Auto **/ UINT16 ImonOffset[5]; /** Offset 0x05D0 - Enable/Disable BIOS configuration of VR Enable/Disable BIOS configuration of VR; 0: Disable; 1: Enable.For all VR Indexes **/ UINT8 VrConfigEnable[5]; /** Offset 0x05D5 - Thermal Design Current enable/disable PCODE MMIO Mailbox: Thermal Design Current enable/disable; 0: Disable; 1: Enable.For all VR Indexes **/ UINT8 TdcEnable[5]; /** Offset 0x05DA **/ UINT8 UnusedUpdSpace29[2]; /** Offset 0x05DC - Thermal Design Current time window PCODE MMIO Mailbox: Thermal Design Current time window. Defined in milli seconds. Range 1ms to 448s **/ UINT32 TdcTimeWindow[5]; /** Offset 0x05F0 - Thermal Design Current Lock PCODE MMIO Mailbox: Thermal Design Current Lock; 0: Disable; 1: Enable.For all VR Indexes **/ UINT8 TdcLock[5]; /** Offset 0x05F5 - Platform Psys slope correction PCODE MMIO Mailbox: Platform Psys slope correction. 0 - Auto Specified in 1/100 increment values. Range is 0-200. 125 = 1.25 **/ UINT8 PsysSlope; /** Offset 0x05F6 - Platform Psys offset correction PCODE MMIO Mailbox: Platform Psys offset correction. 0 - Auto Units 1/1000, Range 0-63999. For an offset of 25.348, enter 25348. **/ UINT16 PsysOffset; /** Offset 0x05F8 - Acoustic Noise Mitigation feature Enable or Disable Acoustic Noise Mitigation feature. 0: Disabled; 1: Enabled $EN_DIS **/ UINT8 AcousticNoiseMitigation; /** Offset 0x05F9 - Disable Fast Slew Rate for Deep Package C States for VR domains Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation feature enabled. 0: False; 1: True $EN_DIS **/ UINT8 FastPkgCRampDisable[5]; /** Offset 0x05FE - Slew Rate configuration for Deep Package C States for VR domains Slew Rate configuration for Deep Package C States for VR domains based on Acoustic Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16 0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16 **/ UINT8 SlowSlewRate[5]; /** Offset 0x0603 **/ UINT8 UnusedUpdSpace30[1]; /** Offset 0x0604 - Thermal Design Current current limit PCODE MMIO Mailbox: Thermal Design Current current limit. Specified in 1/8A units. Range is 0-4095. 1000 = 125A. 0: Auto. For all VR Indexes **/ UINT16 TdcCurrentLimit[5]; /** Offset 0x060E - AcLoadline PCODE MMIO Mailbox: AcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is 0-6249. Intel Recommended Defaults vary by domain and SKU. **/ UINT16 AcLoadline[5]; /** Offset 0x0618 - DcLoadline PCODE MMIO Mailbox: DcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is 0-6249.Intel Recommended Defaults vary by domain and SKU. **/ UINT16 DcLoadline[5]; /** Offset 0x0622 - Power State 1 Threshold current PCODE MMIO Mailbox: Power State 1 current cuttof in 1/4 Amp increments. Range is 0-128A. **/ UINT16 Psi1Threshold[5]; /** Offset 0x062C - Power State 2 Threshold current PCODE MMIO Mailbox: Power State 2 current cuttof in 1/4 Amp increments. Range is 0-128A. **/ UINT16 Psi2Threshold[5]; /** Offset 0x0636 - Power State 3 Threshold current PCODE MMIO Mailbox: Power State 3 current cuttof in 1/4 Amp increments. Range is 0-128A. **/ UINT16 Psi3Threshold[5]; /** Offset 0x0640 - Icc Max limit PCODE MMIO Mailbox: VR Icc Max limit. 0-255A in 1/4 A units. 400 = 100A **/ UINT16 IccMax[5]; /** Offset 0x064A - Enable VR specific mailbox command VR specific mailbox commands. 00b - no VR specific command sent. 01b - A VR mailbox command specifically for the MPS IMPV8 VR will be sent. 10b - VR specific command sent for PS4 exit issue. 11b - Reserved. $EN_DIS **/ UINT8 SendVrMbxCmd; /** Offset 0x064B - Enable or Disable TXT Enable or Disable TXT; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 TxtEnable; /** Offset 0x064C - Skip Multi-Processor Initialization When this is skipped, boot loader must initialize processors before SilicionInit API. 0: Initialize; 1: Skip $EN_DIS **/ UINT8 SkipMpInit; /** Offset 0x064D **/ UINT8 UnusedUpdSpace31; /** Offset 0x064E - FIVR RFI Frequency PCODE MMIO Mailbox: Set the desired RFI frequency, in increments of 100KHz. 0: Auto. Range varies based on XTAL clock: 0-1918 (Up to 191.8HMz) for 24MHz clock; 0-1535 (Up to 153.5MHz) for 19MHz clock. **/ UINT16 FivrRfiFrequency; /** Offset 0x0650 - FIVR RFI Spread Spectrum PCODE MMIO Mailbox: FIVR RFI Spread Spectrum, in 0.1% increments. 0: 0%; Range: 0.0% to 10.0% (0-100). **/ UINT8 FivrSpreadSpectrum; /** Offset 0x0651 **/ UINT8 UnusedUpdSpace32[3]; /** Offset 0x0654 - UFS Soft Strap Start Address UFS Soft Strap Start Address, Value will be based on the CSE IFWI Layout **/ UINT32 UfsStrapAddress; /** Offset 0x0658 - CpuBistData Pointer CPU BIST Data **/ UINT32 CpuBistData; /** Offset 0x065C - CpuMpPpi Optional pointer to the boot loader's implementation of EFI_PEI_MP_SERVICES_PPI. If not NULL, FSP will use the boot loader's implementation of multiprocessing. See section 5.1.4 of the FSP Integration Guide for more details. **/ UINT32 CpuMpPpi; /** Offset 0x0660 - CpuMpHob Optional pointer for CpuMpHob. If the boot loader is a UEFI boot loader using API mode instead of dispatch mode, and FspsUpd->FspsConfig.CpuMpPpi != NULL, then FspsUpd->FspsConfig.CpuMpHob must be != NULL. See section 5.1.4 of the FSP Integration Guide for more details. **/ UINT32 CpuMpHob; /** Offset 0x0664 **/ UINT8 CpuPostMemRsvd[16]; /** Offset 0x0674 - PpinSupport to view Protected Processor Inventory Number Enable or Disable or Auto (Based on End of Manufacturing flag. Disabled if this flag is set) for PPIN Support 0: Disable, 1: Enable, 2: Auto **/ UINT8 PpinSupport; /** Offset 0x0675 - Enable or Disable Minimum Voltage Override Enable or disable Minimum Voltage overrides ; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 EnableMinVoltageOverride; /** Offset 0x0676 - Min Voltage for Runtime PCODE MMIO Mailbox: Minimum voltage for runtime. Valid if EnableMinVoltageOverride = 1. Range 0 to 1999mV. 0: 0mV **/ UINT16 MinVoltageRuntime; /** Offset 0x0678 - Base of memory region allocated for Processor Trace Base address of memory region allocated for Processor Trace. Processor Trace requires 2^N alignment and size in bytes per thread, from 4KB to 128MB. 0: Disable **/ UINT64 ProcessorTraceMemBase; /** Offset 0x0680 - Memory region allocation for Processor Trace Length in bytes of memory region allocated for Processor Trace. Processor Trace requires 2^N alignment and size in bytes per thread, from 4KB to 128MB. 0: Disable **/ UINT32 ProcessorTraceMemLength; /** Offset 0x0684 - Min Voltage for C8 PCODE MMIO Mailbox: Minimum voltage for C8. Valid if EnableMinVoltageOverride = 1. Range 0 to 1999mV. 0: 0mV **/ UINT16 MinVoltageC8; /** Offset 0x0686 - Smbios Type4 Max Speed Override Provide the option for platform to override the MaxSpeed field of Smbios Type 4. If this value is not zero, it dominates the field. **/ UINT16 SmbiosType4MaxSpeedOverride; /** Offset 0x0688 - ReservedCpuPostMemProduction Reserved for CPU Post-Mem Production $EN_DIS **/ UINT8 ReservedCpuPostMemProduction[6]; /** Offset 0x068E - AC Split Lock Enable/Disable #AC check on split lock. 0: Disable; 1: Enable. $EN_DIS **/ UINT8 AcSplitLock; /** Offset 0x068F - PCH Master Clock Gating Control Provide a master control for clock gating for all PCH devices, 0: Disabled; 1: Default $EN_DIS **/ UINT8 PchMasterClockGating; /** Offset 0x0690 - PCH Master Power Gating Control Provide a master control for pwoer gating for all PCH devices, 0: Disabled; 1: Default $EN_DIS **/ UINT8 PchMasterPowerGating; /** Offset 0x0691 - Sci Pin Mux Enable Enable/Disable Sci Gpio Pin Mux. 0: Disable; 1: Enable. $EN_DIS **/ UINT8 SciPinMuxEnable; /** Offset 0x0692 - Enable Power Optimizer Enable DMI Power Optimizer on PCH side. $EN_DIS **/ UINT8 PchPwrOptEnable; /** Offset 0x0693 - PCH Flash Protection Ranges Write Enble Write or erase is blocked by hardware. **/ UINT8 PchWriteProtectionEnable[5]; /** Offset 0x0698 - PCH Flash Protection Ranges Read Enble Read is blocked by hardware. **/ UINT8 PchReadProtectionEnable[5]; /** Offset 0x069D **/ UINT8 UnusedUpdSpace33[1]; /** Offset 0x069E - PCH Protect Range Limit Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for limit comparison. **/ UINT16 PchProtectedRangeLimit[5]; /** Offset 0x06A8 - PCH Protect Range Base Left shifted address by 12 bits with address bits 11:0 are assumed to be 0. **/ UINT16 PchProtectedRangeBase[5]; /** Offset 0x06B2 - Enable Pme Enable Azalia wake-on-ring. $EN_DIS **/ UINT8 PchHdaPme; /** Offset 0x06B3 - HD Audio Link Frequency HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, 1: 12MHz, 2: 24MHz. 0: 6MHz, 1: 12MHz, 2: 24MHz **/ UINT8 PchHdaLinkFrequency; /** Offset 0x06B4 - PchPostMemRsvd Reserved for PCH Post-Mem $EN_DIS **/ UINT8 PchPostMemRsvd4[3]; /** Offset 0x06B7 - Enable PCH Io Apic Entry 24-119 0: Disable; 1: Enable. $EN_DIS **/ UINT8 PchIoApicEntry24_119; /** Offset 0x06B8 - PCH Io Apic ID This member determines IOAPIC ID. Default is 0x02. **/ UINT8 PchIoApicId; /** Offset 0x06B9 **/ UINT8 UnusedUpdSpace34[3]; /** Offset 0x06BC - PCH PSE Log Output Channel Set PSE Log Output Channel. 0: internal memory; 1-6: UART channels; Other: shut down **/ UINT32 PchPseLogOutputChannel; /** Offset 0x06C0 - PCH PSE Log Output Size Set PSE Log Output Size **/ UINT16 PchPseLogOutputSize; /** Offset 0x06C2 - PCH PSE Log Output Offset Set PSE Log Output Offset **/ UINT16 PchPseLogOutputOffset; /** Offset 0x06C4 - PCH PSE OOB Prov State Offset Set PSE OOB Prov State Offset **/ UINT16 PchPseOobProvDone; /** Offset 0x06C6 - Enable PCH PSE I2S pins assigned Set if PSE I2S native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseI2sEnable[2]; /** Offset 0x06C8 - PchPseI2sTxPinMux Select PSE I2S Tx pin muxing. Refer to GPIO_*_MUXING_PSE_I2Sx_TXD* for possible values. **/ UINT32 PchPseI2sTxPinMux[2]; /** Offset 0x06D0 - PchPseI2sRxPinMux Select PSE I2S Rx pin muxing. Refer to GPIO_*_MUXING_PSE_I2Sx_RXD* for possible values. **/ UINT32 PchPseI2sRxPinMux[2]; /** Offset 0x06D8 - PchPseI2sSfrmPinMux Select PSE I2S Sfrm pin muxing. Refer to GPIO_*_MUXING_PSE_I2Sx_SFRM* for possible values. **/ UINT32 PchPseI2sSfrmPinMux[2]; /** Offset 0x06E0 - PchPseI2sSclkPinMux Select PSE I2S Sclk pin muxing. Refer to GPIO_*_MUXING_PSE_I2Sx_SCLK* for possible values. **/ UINT32 PchPseI2sSclkPinMux[2]; /** Offset 0x06E8 - Enable PCH PSE PWM pins assigned Set if PSE PWM native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPsePwmEnable; /** Offset 0x06E9 - PchPsePwmPinEnable Set PWM pin to PSE PWM native function. 0: Disable; 1: Enable. **/ UINT8 PchPsePwmPinEnable[16]; /** Offset 0x06F9 **/ UINT8 UnusedUpdSpace35[3]; /** Offset 0x06FC - PchPsePwmPinMux Select PSE Pwm pin muxing start from PWM0 to PWM15. Refer to GPIO_*_MUXING_PSE_PWM* for possible values. **/ UINT32 PchPsePwmPinMux[16]; /** Offset 0x073C - Enable PCH PSE UART pins assigned Set if PSE UART native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseUartEnable[6]; /** Offset 0x0742 - Enable PCH PSE HSUART pins assigned Set if PSE HSUART native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseHsuartEnable[4]; /** Offset 0x0746 - Enable PCH PSE QEP pins assigned Set if PSE QEP native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseQepEnable[4]; /** Offset 0x074A - Enable PCH PSE DMA pins assigned Set if PSE DMA native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseDmaEnable[3]; /** Offset 0x074D - Enable PCH PSE GBE pins assigned Set if PSE GBE native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseGbeEnable[2]; /** Offset 0x074F - Enable PCH PSE I2C pins assigned Set if PSE I2C native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseI2cEnable[8]; /** Offset 0x0757 - Enable PCH PSE SPI pins assigned Set if PSE SPI native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseSpiEnable[4]; /** Offset 0x075B - Enable PCH PSE SPI CS0 pins assigned Set if PSE SPI CS0 pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseSpiCs0Enable[4]; /** Offset 0x075F - Enable PCH PSE SPI CS1 pins assigned Set if PSE SPI CS1 pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseSpiCs1Enable[4]; /** Offset 0x0763 **/ UINT8 UnusedUpdSpace36[1]; /** Offset 0x0764 - PchPseSpiMosiPinMux Select PSE Spi Mosi pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_MOSI* for possible values. **/ UINT32 PchPseSpiMosiPinMux[4]; /** Offset 0x0774 - PchPseSpiMisoPinMux Select PSE Spi Miso pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_MISO* for possible values. **/ UINT32 PchPseSpiMisoPinMux[4]; /** Offset 0x0784 - PchPseSpiClkPinMux Select PSE Spi Clk pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_SCLK* for possible values. **/ UINT32 PchPseSpiClkPinMux[4]; /** Offset 0x0794 - PchPseSpiCs0PinMux Select PSE Spi Cs pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_Cs* for possible values. **/ UINT32 PchPseSpiCs0PinMux[4]; /** Offset 0x07A4 - PchPseSpiCs1PinMux Select PSE Spi Cs pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_Cs* for possible values. **/ UINT32 PchPseSpiCs1PinMux[4]; /** Offset 0x07B4 - Enable PCH PSE ADC pins assigned Set if PSE ADC native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseAdcEnable; /** Offset 0x07B5 - Enable PCH PSE CAN pins assigned Set if PSE CAN native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseCanEnable[2]; /** Offset 0x07B7 - Enable PCH PSE I2S sideband interrupt Set if PSE I2S are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseI2sSbInterruptEnable[2]; /** Offset 0x07B9 - Enable PCH PSE PWM sideband interrupt Set if PSE PWM are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPsePwmSbInterruptEnable; /** Offset 0x07BA - Enable PCH PSE UART sideband interrupt Set if PSE UART are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseUartSbInterruptEnable[6]; /** Offset 0x07C0 - Enable PCH PSE QEP sideband interrupt Set if PSE QEP are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseQepSbInterruptEnable[4]; /** Offset 0x07C4 - Enable PCH PSE DMA sideband interrupt Set if PSE DMA are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseDmaSbInterruptEnable[3]; /** Offset 0x07C7 - Enable PCH PSE I2C sideband interrupt Set if PSE I2C are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseI2cSbInterruptEnable[8]; /** Offset 0x07CF - Enable PCH PSE SPI sideband interrupt Set if PSE SPI are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseSpiSbInterruptEnable[4]; /** Offset 0x07D3 - Enable PCH PSE ADC sideband interrupt Set if PSE ADC are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseAdcSbInterruptEnable; /** Offset 0x07D4 - Enable PCH PSE LH2OSE sideband interrupt Set if PSE LH2OSE are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseLh2PseSbInterruptEnable; /** Offset 0x07D5 - Enable PCH PSE CAN sideband interrupt Set if PSE CAN are to be set to sideband interrupt. 0: Disable; 1: Enable. **/ UINT8 PchPseCanSbInterruptEnable[2]; /** Offset 0x07D7 - Enable PCH PSE Timed GPIO pins assigned Set if PSE Timed GPIO native pins and ownership are to be enabled by BIOS. 0: Disable/pins are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE; 2: Pins are muxed to PSE IP, the IO is owned by host; **/ UINT8 PchPseTimedGpioEnable[2]; /** Offset 0x07D9 - Enable PCH PSE Timed GPIO 20 pins allocation Allocate 20 pins for PCH PSE Timed GPIO. 0: Top 20 pins; 1: Mid 20 pins; 2: Lower 20 pins. **/ UINT8 PchPseTimedGpioPinAllocation[2]; /** Offset 0x07DB - Enable PCH PSE Timed GPIO Pin to PSE TGPIO native function Set TGPIO pin to PSE TGPIO native function. 0: Disable; 1: Enable. **/ UINT8 PchPseTimedGpioPinEnable[60]; /** Offset 0x0817 **/ UINT8 UnusedUpdSpace37; /** Offset 0x0818 - Pch Pse Tgpio6 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio6PinMux; /** Offset 0x081C - Pch Pse Tgpio7 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio7PinMux; /** Offset 0x0820 - Pch Pse Tgpio8 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio8PinMux; /** Offset 0x0824 - Pch Pse Tgpio9 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio9PinMux; /** Offset 0x0828 - Pch Pse Tgpio10 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio10PinMux; /** Offset 0x082C - Pch Pse Tgpio11 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio11PinMux; /** Offset 0x0830 - Pch Pse Tgpio12 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio12PinMux; /** Offset 0x0834 - Pch Pse Tgpio13 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio13PinMux; /** Offset 0x0838 - Pch Pse Tgpio14 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio14PinMux; /** Offset 0x083C - Pch Pse Tgpio15 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio15PinMux; /** Offset 0x0840 - Pch Pse Tgpio16 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio16PinMux; /** Offset 0x0844 - Pch Pse Tgpio17 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio17PinMux; /** Offset 0x0848 - Pch Pse Tgpio18 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio18PinMux; /** Offset 0x084C - Pch Pse Tgpio19 Pin Mux Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values. **/ UINT32 PchPseTgpio19PinMux; /** Offset 0x0850 - Enable PCH Lan LTR capabilty of PCH internal LAN 0: Disable; 1: Enable. $EN_DIS **/ UINT8 PchLanLtrEnable; /** Offset 0x0851 - Enable LOCKDOWN BIOS LOCK Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region protection. $EN_DIS **/ UINT8 PchLockDownBiosLock; /** Offset 0x0852 - PCH Compatibility Revision ID This member describes whether or not the CRID feature of PCH should be enabled. $EN_DIS **/ UINT8 PchCrid; /** Offset 0x0853 - RTC BIOS Interface Lock Enable RTC BIOS interface lock. When set, prevents RTC TS (BUC.TS) from being changed. $EN_DIS **/ UINT8 RtcBiosInterfaceLock; /** Offset 0x0854 - RTC Cmos Memory Lock Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper and and lower 128-byte bank of RTC RAM. $EN_DIS **/ UINT8 RtcMemoryLock; /** Offset 0x0855 - Enable PCIE RP HotPlug Indicate whether the root port is hot plug available. **/ UINT8 PcieRpHotPlug[24]; /** Offset 0x086D - Enable PCIE RP Pm Sci Indicate whether the root port power manager SCI is enabled. **/ UINT8 PcieRpPmSci[24]; /** Offset 0x0885 - Enable PCIE RP Transmitter Half Swing Indicate whether the Transmitter Half Swing is enabled. **/ UINT8 PcieRpTransmitterHalfSwing[24]; /** Offset 0x089D - Enable PCIE RP Clk Req Detect Probe CLKREQ# signal before enabling CLKREQ# based power management. **/ UINT8 PcieRpClkReqDetect[24]; /** Offset 0x08B5 - PCIE RP Advanced Error Report Indicate whether the Advanced Error Reporting is enabled. **/ UINT8 PcieRpAdvancedErrorReporting[24]; /** Offset 0x08CD - PCIE RP Unsupported Request Report Indicate whether the Unsupported Request Report is enabled. **/ UINT8 PcieRpUnsupportedRequestReport[24]; /** Offset 0x08E5 - PCIE RP Fatal Error Report Indicate whether the Fatal Error Report is enabled. **/ UINT8 PcieRpFatalErrorReport[24]; /** Offset 0x08FD - PCIE RP No Fatal Error Report Indicate whether the No Fatal Error Report is enabled. **/ UINT8 PcieRpNoFatalErrorReport[24]; /** Offset 0x0915 - PCIE RP Correctable Error Report Indicate whether the Correctable Error Report is enabled. **/ UINT8 PcieRpCorrectableErrorReport[24]; /** Offset 0x092D - PCIE RP System Error On Fatal Error Indicate whether the System Error on Fatal Error is enabled. **/ UINT8 PcieRpSystemErrorOnFatalError[24]; /** Offset 0x0945 - PCIE RP System Error On Non Fatal Error Indicate whether the System Error on Non Fatal Error is enabled. **/ UINT8 PcieRpSystemErrorOnNonFatalError[24]; /** Offset 0x095D - PCIE RP System Error On Correctable Error Indicate whether the System Error on Correctable Error is enabled. **/ UINT8 PcieRpSystemErrorOnCorrectableError[24]; /** Offset 0x0975 - PCIE RP Max Payload Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD. **/ UINT8 PcieRpMaxPayload[24]; /** Offset 0x098D - Touch Host Controller Port 0 Assignment Assign THC Port 0 0x0:ThcAssignmentNone, 0x1:ThcAssignmentThc0 **/ UINT8 ThcPort0Assignment; /** Offset 0x098E **/ UINT8 UnusedUpdSpace38[2]; /** Offset 0x0990 - THC Port 0 Interrupt Pin Mux Set THC Port 0 Pin Muxing Value if signal can be enabled on multiple pads. Refer to GPIO_*_MUXING_THC_SPIx_INTB_* for possible values. **/ UINT32 ThcPort0InterruptPinMuxing; /** Offset 0x0994 - Touch Host Controller Port 1 Assignment Assign THC Port 1 0x0:ThcAssignmentNone, 0x1:ThcPort1AssignmentThc0, 0x2:ThcAssignmentThc1 **/ UINT8 ThcPort1Assignment; /** Offset 0x0995 - Touch Host Controller Port 1 ReadFrequency Set THC Port 1 Read Frequency (THC_PORT_FREQUENCY enum): 0:2p1MHz,1:2p5Mz,2:3Mz,3:3p75Mz,4:5MHz,5:7p5MHz,6:15MHz,7:17MHz,8:20MHz,9:24MHz,10:30MHz 0:2p1MHz,1:2p5Mz,2:3Mz,3:3p75Mz,4:5MHz,5:7p5MHz,6:15MHz,7:17MHz,8:20MHz,9:24MHz,10:30MHz **/ UINT8 ThcPort1ReadFrequency; /** Offset 0x0996 - Touch Host Controller Port 1 WriteFrequency Set THC Port 1 Write Frequency (THC_PORT_FREQUENCY enum): 0:2p1MHz,1:2p5Mz,2:3Mz,3:3p75Mz,4:5MHz,5:7p5MHz,6:15MHz,7:17MHz,8:20MHz,9:24MHz,10:30MHz 0:2p1MHz,1:2p5Mz,2:3Mz,3:3p75Mz,4:5MHz,5:7p5MHz,6:15MHz,7:17MHz,8:20MHz,9:24MHz,10:30MHz **/ UINT8 ThcPort1WriteFrequency; /** Offset 0x0997 **/ UINT8 UnusedUpdSpace39; /** Offset 0x0998 - THC Port 1 Interrupt Pin Mux Set THC Port 1 Pin Muxing Value if signal can be enabled on multiple pads. Refer to GPIO_*_MUXING_THC_SPIx_INTB_* for possible values. **/ UINT32 ThcPort1InterruptPinMuxing; /** Offset 0x099C - PCIE RP Pcie Speed Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3 (see: PCH_PCIE_SPEED). **/ UINT8 PcieRpPcieSpeed[24]; /** Offset 0x09B4 - PCIE RP Physical Slot Number Indicates the slot number for the root port. Default is the value as root port index. **/ UINT8 PcieRpPhysicalSlotNumber[24]; /** Offset 0x09CC - PCIE RP Completion Timeout The root port completion timeout(see: PCH_PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default. **/ UINT8 PcieRpCompletionTimeout[24]; /** Offset 0x09E4 - PCIE RP Aspm The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is PchPcieAspmAutoConfig. **/ UINT8 PcieRpAspm[24]; /** Offset 0x09FC - PCIE RP L1 Substates The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL). Default is PchPcieL1SubstatesL1_1_2. **/ UINT8 PcieRpL1Substates[24]; /** Offset 0x0A14 - PCIE RP Ltr Enable Latency Tolerance Reporting Mechanism. **/ UINT8 PcieRpLtrEnable[24]; /** Offset 0x0A2C - PCIE RP Ltr Config Lock 0: Disable; 1: Enable. **/ UINT8 PcieRpLtrConfigLock[24]; /** Offset 0x0A44 - PCIe override default settings for EQ Choose PCIe EQ method $EN_DIS **/ UINT8 PcieEqOverrideDefault; /** Offset 0x0A45 - PCIe choose EQ method Choose PCIe EQ method 0: HardwareEq, 1: FixedEq **/ UINT8 PcieEqMethod; /** Offset 0x0A46 - PCIe choose EQ mode Choose PCIe EQ mode 0: PresetEq, 1: CoefficientEq **/ UINT8 PcieEqMode; /** Offset 0x0A47 - PCIe EQ local transmitter override Enable/Disable local transmitter override $EN_DIS **/ UINT8 PcieEqLocalTransmitterOverrideEnable; /** Offset 0x0A48 - PCIe number of valid list entries Select number of presets or coefficients depending on the mode **/ UINT8 PcieEqPh3NumberOfPresetsOrCoefficients; /** Offset 0x0A49 - PCIe pre-cursor coefficient list Provide a list of pre-cursor coefficients to be used during phase 3 EQ **/ UINT8 PcieEqPh3PreCursorList[10]; /** Offset 0x0A53 - PCIe post-cursor coefficient list Provide a list of post-cursor coefficients to be used during phase 3 EQ **/ UINT8 PcieEqPh3PostCursorList[10]; /** Offset 0x0A5D - PCIe preset list Provide a list of presets to be used during phase 3 EQ **/ UINT8 PcieEqPh3PresetList[11]; /** Offset 0x0A68 - PCIe EQ phase 1 downstream transmitter port preset Allows to select the downstream port preset value that will be used during phase 1 of equalization **/ UINT32 PcieEqPh1DownstreamPortTransmitterPreset; /** Offset 0x0A6C - PCIe EQ phase 1 upstream tranmitter port preset Allows to select the upstream port preset value that will be used during phase 1 of equalization **/ UINT32 PcieEqPh1UpstreamPortTransmitterPreset; /** Offset 0x0A70 - PCIe EQ phase 2 local transmitter override preset Allows to select the value of the preset used during phase 2 local transmitter override **/ UINT8 PcieEqPh2LocalTransmitterOverridePreset; /** Offset 0x0A71 - PCIE Enable Peer Memory Write This member describes whether Peer Memory Writes are enabled on the platform. $EN_DIS **/ UINT8 PcieEnablePeerMemoryWrite; /** Offset 0x0A72 - PCIE Compliance Test Mode Compliance Test Mode shall be enabled when using Compliance Load Board. $EN_DIS **/ UINT8 PcieComplianceTestMode; /** Offset 0x0A73 - PCI Express Clock Gating Enable/Disable Clock Gating, 0: PLATFORM_POR, 1: FORCE_ENABLE, 2: FORCE_DISABLE. 0: POR, 1: Force Enable, 2: Force Disable **/ UINT8 TestPcieClockGating; /** Offset 0x0A74 - PCIE Rp Function Swap Allows BIOS to use root port function number swapping when root port of function 0 is disabled. $EN_DIS **/ UINT8 PcieRpFunctionSwap; /** Offset 0x0A75 - Enable/Disable PEG GEN3 Static EQ Phase1 programming Program Gen3 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets Programming, Enabled(0x1)(Default): Enable EQ Phase1 Static Presets Programming $EN_DIS **/ UINT8 CpuPcieGen3ProgramStaticEq; /** Offset 0x0A76 - Enable/Disable GEN4 Static EQ Phase1 programming Program Gen4 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets Programming, Enabled(0x1)(Default): Enable EQ Phase1 Static Presets Programming $EN_DIS **/ UINT8 CpuPcieGen4ProgramStaticEq; /** Offset 0x0A77 - PCH Pm PME_B0_S5_DIS When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1. $EN_DIS **/ UINT8 PchPmPmeB0S5Dis; /** Offset 0x0A78 - PCIE IMR Enables Isolated Memory Region for PCIe. $EN_DIS **/ UINT8 PcieRpImrEnabled; /** Offset 0x0A79 - PCIE IMR port number Selects PCIE root port number for IMR feature. **/ UINT8 PcieRpImrSelection; /** Offset 0x0A7A - PCH Pm Wol Enable Override Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register. $EN_DIS **/ UINT8 PchPmWolEnableOverride; /** Offset 0x0A7B - PCH Pm Pcie Wake From DeepSx Determine if enable PCIe to wake from deep Sx. $EN_DIS **/ UINT8 PchPmPcieWakeFromDeepSx; /** Offset 0x0A7C - PCH Pm WoW lan Enable Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register. $EN_DIS **/ UINT8 PchPmWoWlanEnable; /** Offset 0x0A7D - PCH Pm WoW lan DeepSx Enable Determine if WLAN wake from DeepSx, corresponds to the DSX_WLAN_PP_EN bit in the PWRM_CFG3 register. $EN_DIS **/ UINT8 PchPmWoWlanDeepSxEnable; /** Offset 0x0A7E - PCH Pm Lan Wake From DeepSx Determine if enable LAN to wake from deep Sx. $EN_DIS **/ UINT8 PchPmLanWakeFromDeepSx; /** Offset 0x0A7F - PCH Pm Deep Sx Pol Deep Sx Policy. $EN_DIS **/ UINT8 PchPmDeepSxPol; /** Offset 0x0A80 - PCH Pm Slp S3 Min Assert SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms. **/ UINT8 PchPmSlpS3MinAssert; /** Offset 0x0A81 - PCH Pm Slp S4 Min Assert SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s. **/ UINT8 PchPmSlpS4MinAssert; /** Offset 0x0A82 - PCH Pm Slp Sus Min Assert SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s. **/ UINT8 PchPmSlpSusMinAssert; /** Offset 0x0A83 - PCH Pm Slp A Min Assert SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s. **/ UINT8 PchPmSlpAMinAssert; /** Offset 0x0A84 - USB Overcurrent Override for DbC This option overrides USB Over Current enablement state that USB OC will be disabled after enabling this option. Enable when DbC is used to avoid signaling conflicts. $EN_DIS **/ UINT8 PchEnableDbcObs; /** Offset 0x0A85 - PCH Pm Slp Strch Sus Up Enable SLP_X Stretching After SUS Well Power Up. $EN_DIS **/ UINT8 PchPmSlpStrchSusUp; /** Offset 0x0A86 - PCH Pm Slp Lan Low Dc Enable/Disable SLP_LAN# Low on DC Power. $EN_DIS **/ UINT8 PchPmSlpLanLowDc; /** Offset 0x0A87 - PCH Pm Pwr Btn Override Period PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s. **/ UINT8 PchPmPwrBtnOverridePeriod; /** Offset 0x0A88 - PCH Pm Disable Dsx Ac Present Pulldown When Disable, PCH will internal pull down AC_PRESENT in deep SX and during G3 exit. $EN_DIS **/ UINT8 PchPmDisableDsxAcPresentPulldown; /** Offset 0x0A89 - PCH Pm Disable Native Power Button Power button native mode disable. $EN_DIS **/ UINT8 PchPmDisableNativePowerButton; /** Offset 0x0A8A - PCH Pm ME_WAKE_STS Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register. $EN_DIS **/ UINT8 PchPmMeWakeSts; /** Offset 0x0A8B - PCH Pm WOL_OVR_WK_STS Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register. $EN_DIS **/ UINT8 PchPmWolOvrWkSts; /** Offset 0x0A8C - PCH Pm Reset Power Cycle Duration Could be customized in the unit of second. Please refer to EDS for all support settings. 0 is default, 1 is 1 second, 2 is 2 seconds, ... **/ UINT8 PchPmPwrCycDur; /** Offset 0x0A8D - PCH Pm Pcie Pll Ssc Specifies the Pcie Pll Spread Spectrum Percentage. The default is 0xFF: AUTO - No BIOS override. **/ UINT8 PchPmPciePllSsc; /** Offset 0x0A8E - PCH Legacy IO Low Latency Enable Set to enable low latency of legacy IO. 0: Disable, 1: Enable $EN_DIS **/ UINT8 PchLegacyIoLowLatency; /** Offset 0x0A8F - PCH Sata Pwr Opt Enable SATA Power Optimizer on PCH side. $EN_DIS **/ UINT8 SataPwrOptEnable; /** Offset 0x0A90 - PCH Sata eSATA Speed Limit When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed. $EN_DIS **/ UINT8 EsataSpeedLimit; /** Offset 0x0A91 - PCH Sata Speed Limit Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault. **/ UINT8 SataSpeedLimit; /** Offset 0x0A92 - Enable SATA Port HotPlug Enable SATA Port HotPlug. **/ UINT8 SataPortsHotPlug[8]; /** Offset 0x0A9A - Enable SATA Port Interlock Sw Enable SATA Port Interlock Sw. **/ UINT8 SataPortsInterlockSw[8]; /** Offset 0x0AA2 - Enable SATA Port External Enable SATA Port External. **/ UINT8 SataPortsExternal[8]; /** Offset 0x0AAA - Enable SATA Port SpinUp Enable the COMRESET initialization Sequence to the device. **/ UINT8 SataPortsSpinUp[8]; /** Offset 0x0AB2 - Enable SATA Port Solid State Drive 0: HDD; 1: SSD. **/ UINT8 SataPortsSolidStateDrive[8]; /** Offset 0x0ABA - Enable SATA Port Enable Dito Config Enable DEVSLP Idle Timeout settings (DmVal, DitoVal). **/ UINT8 SataPortsEnableDitoConfig[8]; /** Offset 0x0AC2 - Enable SATA Port DmVal DITO multiplier. Default is 15. **/ UINT8 SataPortsDmVal[8]; /** Offset 0x0ACA - Enable SATA Port DmVal DEVSLP Idle Timeout (DITO), Default is 625. **/ UINT16 SataPortsDitoVal[8]; /** Offset 0x0ADA - Enable SATA Port ZpOdd Support zero power ODD. **/ UINT8 SataPortsZpOdd[8]; /** Offset 0x0AE2 - Enable SATA Port RxPolarity Reverse RxPolarity. **/ UINT8 SataPortsRxPolarity[8]; /** Offset 0x0AEA - PCH Sata Rst Raid Alternate Id Enable RAID Alternate ID. $EN_DIS **/ UINT8 SataRstRaidDeviceId; /** Offset 0x0AEB - PCH Sata Rst Raid0 RAID0. $EN_DIS **/ UINT8 SataRstRaid0; /** Offset 0x0AEC - PCH Sata Rst Raid1 RAID1. $EN_DIS **/ UINT8 SataRstRaid1; /** Offset 0x0AED - PCH Sata Rst Raid10 RAID10. $EN_DIS **/ UINT8 SataRstRaid10; /** Offset 0x0AEE - PCH Sata Rst Raid5 RAID5. $EN_DIS **/ UINT8 SataRstRaid5; /** Offset 0x0AEF - PCH Sata Rst Irrt Intel Rapid Recovery Technology. $EN_DIS **/ UINT8 SataRstIrrt; /** Offset 0x0AF0 - PCH Sata Rst Orom Ui Banner OROM UI and BANNER. $EN_DIS **/ UINT8 SataRstOromUiBanner; /** Offset 0x0AF1 - PCH Sata Rst Orom Ui Delay 00b: 2 secs; 01b: 4 secs; 10b: 6 secs; 11: 8 secs (see: PCH_SATA_OROM_DELAY). **/ UINT8 SataRstOromUiDelay; /** Offset 0x0AF2 - PCH Sata Rst Hdd Unlock Indicates that the HDD password unlock in the OS is enabled. $EN_DIS **/ UINT8 SataRstHddUnlock; /** Offset 0x0AF3 - PCH Sata Rst Led Locate Indicates that the LED/SGPIO hardware is attached and ping to locate feature is enabled on the OS. $EN_DIS **/ UINT8 SataRstLedLocate; /** Offset 0x0AF4 - PCH Sata Rst Irrt Only Allow only IRRT drives to span internal and external ports. $EN_DIS **/ UINT8 SataRstIrrtOnly; /** Offset 0x0AF5 - PCH Sata Rst Smart Storage RST Smart Storage caching Bit. $EN_DIS **/ UINT8 SataRstSmartStorage; /** Offset 0x0AF6 - PCH Sata Rst Pcie Storage Remap enable Enable Intel RST for PCIe Storage remapping. **/ UINT8 SataRstPcieEnable[3]; /** Offset 0x0AF9 - PCH Sata Rst Pcie Storage Port Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect). **/ UINT8 SataRstPcieStoragePort[3]; /** Offset 0x0AFC - PCH Sata Rst Pcie Device Reset Delay PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms **/ UINT8 SataRstPcieDeviceResetDelay[3]; /** Offset 0x0AFF - UFS enable/disable PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms $EN_DIS **/ UINT8 UfsEnable[2]; /** Offset 0x0B01 - IEH Mode Integrated Error Handler Mode, 0: Bypass, 1: Enable 0: Bypass, 1:Enable **/ UINT8 IehMode; /** Offset 0x0B02 - PSF Tcc Psf Tcc (Time Coordinated Computing) Enable will decrease psf transaction latency by disable some psf power management features, 0: Disable, 1: Enable $EN_DIS **/ UINT8 PsfTccEnable; /** Offset 0x0B03 - TCC Mode Default Flag Variable to determine TCC mode default value, 0: Disable, 1: Enable $EN_DIS **/ UINT8 TccModeInitFlag; /** Offset 0x0B04 - Tcc Tuning enable/disable Tcc (Time Coordinated Computing) Tuning Enabled $EN_DIS **/ UINT8 TccTuningEnable; /** Offset 0x0B05 **/ UINT8 UnusedUpdSpace40[3]; /** Offset 0x0B08 - Tcc Register File Base Address Tcc (Time Coordinated Computing) Register File Base Address **/ UINT32 TccConfigBase; /** Offset 0x0B0C - Tcc Register File Size Tcc (Time Coordinated Computing) Register File Size **/ UINT32 TccConfigSize; /** Offset 0x0B10 - Fusa Display Configuration Fusa (Functional Safety) Enable Fusa Feature on Display, 0: Disable, 1: Enable $EN_DIS **/ UINT8 DisplayFusaConfigEnable; /** Offset 0x0B11 - Fusa Graphics Configuration Fusa (Functional Safety) Enable Fusa Feature on Graphics, 0: Disable, 1: Enable $EN_DIS **/ UINT8 GraphicFusaConfigEnable; /** Offset 0x0B12 - Fusa Opio Configuration Fusa (Functional Safety) Enable Fusa Feature on Opio, 0: Disable, 1: Enable $EN_DIS **/ UINT8 OpioFusaConfigEnable; /** Offset 0x0B13 - Fusa Psf Configuration Fusa (Functional Safety) Enable Fusa Feature on Psf, 0: Disable, 1: Enable $EN_DIS **/ UINT8 PsfFusaConfigEnable; /** Offset 0x0B14 - Thermal Throttling Custimized T0Level Value Custimized T0Level value. **/ UINT16 PchT0Level; /** Offset 0x0B16 - Thermal Throttling Custimized T1Level Value Custimized T1Level value. **/ UINT16 PchT1Level; /** Offset 0x0B18 - Thermal Throttling Custimized T2Level Value Custimized T2Level value. **/ UINT16 PchT2Level; /** Offset 0x0B1A - Enable The Thermal Throttle Enable the thermal throttle function. $EN_DIS **/ UINT8 PchTTEnable; /** Offset 0x0B1B - PMSync State 13 When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force at least T2 state. $EN_DIS **/ UINT8 PchTTState13Enable; /** Offset 0x0B1C - Thermal Throttle Lock Thermal Throttle Lock. $EN_DIS **/ UINT8 PchTTLock; /** Offset 0x0B1D - Thermal Throttling Suggested Setting Thermal Throttling Suggested Setting. $EN_DIS **/ UINT8 TTSuggestedSetting; /** Offset 0x0B1E - Enable PCH Cross Throttling Enable/Disable PCH Cross Throttling $EN_DIS **/ UINT8 TTCrossThrottling; /** Offset 0x0B1F - DMI Thermal Sensor Autonomous Width Enable DMI Thermal Sensor Autonomous Width Enable. $EN_DIS **/ UINT8 PchDmiTsawEn; /** Offset 0x0B20 - DMI Thermal Sensor Suggested Setting DMT thermal sensor suggested representative values. $EN_DIS **/ UINT8 DmiSuggestedSetting; /** Offset 0x0B21 - Thermal Sensor 0 Target Width Thermal Sensor 0 Target Width. 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 **/ UINT8 DmiTS0TW; /** Offset 0x0B22 - Thermal Sensor 1 Target Width Thermal Sensor 1 Target Width. 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 **/ UINT8 DmiTS1TW; /** Offset 0x0B23 - Thermal Sensor 2 Target Width Thermal Sensor 2 Target Width. 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 **/ UINT8 DmiTS2TW; /** Offset 0x0B24 - Thermal Sensor 3 Target Width Thermal Sensor 3 Target Width. 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 **/ UINT8 DmiTS3TW; /** Offset 0x0B25 - Port 0 T1 Multipler Port 0 T1 Multipler. **/ UINT8 SataP0T1M; /** Offset 0x0B26 - Port 0 T2 Multipler Port 0 T2 Multipler. **/ UINT8 SataP0T2M; /** Offset 0x0B27 - Port 0 T3 Multipler Port 0 T3 Multipler. **/ UINT8 SataP0T3M; /** Offset 0x0B28 - Port 0 Tdispatch Port 0 Tdispatch. **/ UINT8 SataP0TDisp; /** Offset 0x0B29 - Port 1 T1 Multipler Port 1 T1 Multipler. **/ UINT8 SataP1T1M; /** Offset 0x0B2A - Port 1 T2 Multipler Port 1 T2 Multipler. **/ UINT8 SataP1T2M; /** Offset 0x0B2B - Port 1 T3 Multipler Port 1 T3 Multipler. **/ UINT8 SataP1T3M; /** Offset 0x0B2C - Port 1 Tdispatch Port 1 Tdispatch. **/ UINT8 SataP1TDisp; /** Offset 0x0B2D - Port 0 Tinactive Port 0 Tinactive. **/ UINT8 SataP0Tinact; /** Offset 0x0B2E - Port 0 Alternate Fast Init Tdispatch Port 0 Alternate Fast Init Tdispatch. $EN_DIS **/ UINT8 SataP0TDispFinit; /** Offset 0x0B2F - Port 1 Tinactive Port 1 Tinactive. **/ UINT8 SataP1Tinact; /** Offset 0x0B30 - Port 1 Alternate Fast Init Tdispatch Port 1 Alternate Fast Init Tdispatch. $EN_DIS **/ UINT8 SataP1TDispFinit; /** Offset 0x0B31 - Sata Thermal Throttling Suggested Setting Sata Thermal Throttling Suggested Setting. $EN_DIS **/ UINT8 SataThermalSuggestedSetting; /** Offset 0x0B32 - Enable Memory Thermal Throttling Enable Memory Thermal Throttling. $EN_DIS **/ UINT8 PchMemoryThrottlingEnable; /** Offset 0x0B33 - Memory Thermal Throttling Enable Memory Thermal Throttling. **/ UINT8 PchMemoryPmsyncEnable[2]; /** Offset 0x0B35 - Enable Memory Thermal Throttling Enable Memory Thermal Throttling. **/ UINT8 PchMemoryC0TransmitEnable[2]; /** Offset 0x0B37 - Enable Memory Thermal Throttling Enable Memory Thermal Throttling. **/ UINT8 PchMemoryPinSelection[2]; /** Offset 0x0B39 **/ UINT8 UnusedUpdSpace41; /** Offset 0x0B3A - Thermal Device Temperature Decides the temperature. **/ UINT16 PchTemperatureHotLevel; /** Offset 0x0B3C - Enable xHCI Compliance Mode Compliance Mode can be enabled for testing through this option but this is disabled by default. $EN_DIS **/ UINT8 PchEnableComplianceMode; /** Offset 0x0B3D - USB2 Port Over Current Pin Describe the specific over current pin number of USB 2.0 Port N. **/ UINT8 Usb2OverCurrentPin[16]; /** Offset 0x0B4D - USB3 Port Over Current Pin Describe the specific over current pin number of USB 3.0 Port N. **/ UINT8 Usb3OverCurrentPin[10]; /** Offset 0x0B57 - Enable xHCI LTR override Enables override of recommended LTR values for xHCI $EN_DIS **/ UINT8 PchUsbLtrOverrideEnable; /** Offset 0x0B58 - USB Clock Gating Enable Enable or disable USB clock gating $EN_DIS **/ UINT8 UsbClockGatingEnable; /** Offset 0x0B59 - USB Power Gating Enable Enable or disable USB power gating $EN_DIS **/ UINT8 UsbPowerGatingEnable; /** Offset 0x0B5A - USB3 LINK SPEED Set USB3 LINK SPEED=0 for GEN2, Set USB3 LINK SPEED=1 for GEN1 **/ UINT8 USB3LinkSpeed; /** Offset 0x0B5B **/ UINT8 UnusedUpdSpace42; /** Offset 0x0B5C - xHCI High Idle Time LTR override Value used for overriding LTR recommendation for xHCI High Idle Time LTR setting **/ UINT32 PchUsbLtrHighIdleTimeOverride; /** Offset 0x0B60 - xHCI Medium Idle Time LTR override Value used for overriding LTR recommendation for xHCI Medium Idle Time LTR setting **/ UINT32 PchUsbLtrMediumIdleTimeOverride; /** Offset 0x0B64 - xHCI Low Idle Time LTR override Value used for overriding LTR recommendation for xHCI Low Idle Time LTR setting **/ UINT32 PchUsbLtrLowIdleTimeOverride; /** Offset 0x0B68 - Enable 8254 Static Clock Gating Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support legacy OS using 8254 timer. Also enable this while S0ix is enabled. $EN_DIS **/ UINT8 Enable8254ClockGating; /** Offset 0x0B69 - Enable 8254 Static Clock Gating On S3 This is only applicable when Enable8254ClockGating is disabled. FSP will do the 8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This avoids the SMI requirement for the programming. $EN_DIS **/ UINT8 Enable8254ClockGatingOnS3; /** Offset 0x0B6A - PCH Sata Rst Optane Memory Optane Memory $EN_DIS **/ UINT8 SataRstOptaneMemory; /** Offset 0x0B6B - PCH Sata Rst CPU Attached Storage CPU Attached Storage $EN_DIS **/ UINT8 SataRstCpuAttachedStorage; /** Offset 0x0B6C - Enable TCO timer. When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer emulation must be enabled, and WDAT table must not be exposed to the OS. $EN_DIS **/ UINT8 EnableTcoTimer; /** Offset 0x0B6D - Enable Timed GPIO 0. When FALSE, it disables Timed GPIO 0. $EN_DIS **/ UINT8 EnableTimedGpio0; /** Offset 0x0B6E - Enable Timed GPIO 1. When FALSE, it disables Timed GPIO 1. $EN_DIS **/ UINT8 EnableTimedGpio1; /** Offset 0x0B6F - Enable VNN Voltage Raise. When TRUE, it enable VNN Voltage Raise. $EN_DIS **/ UINT8 EnableVnnVoltageRaise; /** Offset 0x0B70 - BgpdtHash[4] BgpdtHash values **/ UINT64 BgpdtHash[4]; /** Offset 0x0B90 - BiosGuardAttr BiosGuardAttr default values **/ UINT32 BiosGuardAttr; /** Offset 0x0B94 **/ UINT8 UnusedUpdSpace43[4]; /** Offset 0x0B98 - BiosGuardModulePtr BiosGuardModulePtr default values **/ UINT64 BiosGuardModulePtr; /** Offset 0x0BA0 - SendEcCmd SendEcCmd function pointer. \n @code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE EcCmdType, IN UINT8 EcCmd, IN UINT8 SendData, IN OUT UINT8 *ReceiveData); @endcode **/ UINT64 SendEcCmd; /** Offset 0x0BA8 - EcCmdProvisionEav Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC **/ UINT8 EcCmdProvisionEav; /** Offset 0x0BA9 - EcCmdLock EcCmdLock default values. Locks Ephemeral Authorization Value sent previously **/ UINT8 EcCmdLock; /** Offset 0x0BAA - Si Config CSM Flag. Platform specific common policies that used by several silicon components. CSM status flag. $EN_DIS **/ UINT8 SiCsmFlag; /** Offset 0x0BAB - Skip Ssid Programming. When set to TRUE, silicon code will not do any SSID programming and platform code needs to handle that by itself properly. $EN_DIS **/ UINT8 SiSkipSsidProgramming; /** Offset 0x0BAC - Change Default SVID Change the default SVID used in FSP to programming internal devices. This is only valid when SkipSsidProgramming is FALSE. **/ UINT16 SiCustomizedSvid; /** Offset 0x0BAE - Change Default SSID Change the default SSID used in FSP to programming internal devices. This is only valid when SkipSsidProgramming is FALSE. **/ UINT16 SiCustomizedSsid; /** Offset 0x0BB0 - SVID SDID table Poniter. The address of the table of SVID SDID to customize each SVID SDID entry. This is only valid when SkipSsidProgramming is FALSE. **/ UINT32 SiSsidTablePtr; /** Offset 0x0BB4 - Number of ssid table. SiNumberOfSsidTableEntry should match the table entries created in SiSsidTablePtr. This is only valid when SkipSsidProgramming is FALSE. **/ UINT16 SiNumberOfSsidTableEntry; /** Offset 0x0BB6 **/ UINT8 SiPostMemRsvd[16]; /** Offset 0x0BC6 - SATA RST Interrupt Mode Allowes to choose which interrupts will be implemented by SATA controller in RAID mode. 0:Msix, 1:Msi, 2:Legacy **/ UINT8 SataRstInterrupt; /** Offset 0x0BC7 - ME Unconfig on RTC clear 0: Disable ME Unconfig On Rtc Clear. 1: Enable ME Unconfig On Rtc Clear. 2: Cmos is clear, status unkonwn. 3: Reserved 0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos is clear, 3: Reserved **/ UINT8 MeUnconfigOnRtcClear; /** Offset 0x0BC8 - Enable PS_ON. PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power target that will be required by the California Energy Commission (CEC). When FALSE, PS_ON is to be disabled. $EN_DIS **/ UINT8 PsOnEnable; /** Offset 0x0BC9 - Pmc Cpu C10 Gate Pin Enable Enable/Disable platform support for CPU_C10_GATE# pin to control gating of CPU VccIO and VccSTG rails instead of SLP_S0# pin. $EN_DIS **/ UINT8 PmcCpuC10GatePinEnable; /** Offset 0x0BCA - Pch Dmi Aspm Ctrl ASPM configuration on the PCH side of the DMI/OPI Link. Default is PchPcieAspmAutoConfig 0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto **/ UINT8 PchDmiAspmCtrl; /** Offset 0x0BCB - PchDmiCwbEnable Central Write Buffer feature configurable and disabled by default $EN_DIS **/ UINT8 PchDmiCwbEnable; /** Offset 0x0BCC - OS IDLE Mode Enable Enable/Disable OS Idle Mode $EN_DIS **/ UINT8 PmcOsIdleEnable; /** Offset 0x0BCD - S0ix Auto-Demotion Enable/Disable the Low Power Mode Auto-Demotion Host Control feature. $EN_DIS **/ UINT8 PchS0ixAutoDemotion; /** Offset 0x0BCE - Global Reset TSC Enable Enable/Disable PMC Global Reset Three Strike Counter feature. If enabled, PMC will keep the platform in S5 after the third consecutive type 7 global reset occurs during boot flow $EN_DIS **/ UINT8 PmcGrTscEnable; /** Offset 0x0BCF - Latch Events C10 Exit When this bit is set to 1, SLP_S0# entry events in SLP_S0_DEBUG_REGx registers are captured on C10 exit (instead of C10 entry which is default) $EN_DIS **/ UINT8 PchPmLatchEventsC10Exit; /** Offset 0x0BD0 - PCIE Eq Ph3 Lane Param Cm CPU_PCIE_EQ_LANE_PARAM. Coefficient C-1. **/ UINT8 CpuPcieEqPh3LaneParamCm[32]; /** Offset 0x0BF0 - PCIE Eq Ph3 Lane Param Cp CPU_PCIE_EQ_LANE_PARAM. Coefficient C+1. **/ UINT8 CpuPcieEqPh3LaneParamCp[32]; /** Offset 0x0C10 - PCIE Hw Eq Gen3 CoeffList Cm CPU_PCIE_EQ_PARAM. Coefficient C-1. **/ UINT8 CpuPcieHwEqGen3CoeffListCm[5]; /** Offset 0x0C15 - PCIE Hw Eq Gen3 CoeffList Cp CPU_PCIE_EQ_PARAM. Coefficient C+1. **/ UINT8 CpuPcieHwEqGen3CoeffListCp[5]; /** Offset 0x0C1A - PCIE Hw Eq Gen4 CoeffList Cm CPU_PCIE_EQ_PARAM. Coefficient C-1. **/ UINT8 CpuPcieHwEqGen4CoeffListCm[5]; /** Offset 0x0C1F - PCIE Hw Eq Gen4 CoeffList Cp CPU_PCIE_EQ_PARAM. Coefficient C+1. **/ UINT8 CpuPcieHwEqGen4CoeffListCp[5]; /** Offset 0x0C24 - Gen3 Root port preset values per lane Used for programming Pcie Gen3 preset values per lane. Range: 0-9, 8 is default for each lane **/ UINT8 CpuPcieGen3RootPortPreset[20]; /** Offset 0x0C38 - Pcie Gen4 Root port preset values per lane Used for programming Pcie Gen4 preset values per lane. Range: 0-9, 8 is default for each lane **/ UINT8 CpuPcieGen4RootPortPreset[20]; /** Offset 0x0C4C - Pcie Gen3 End port preset values per lane Used for programming Pcie Gen3 preset values per lane. Range: 0-9, 7 is default for each lane **/ UINT8 CpuPcieGen3EndPointPreset[20]; /** Offset 0x0C60 - Pcie Gen4 End port preset values per lane Used for programming Pcie Gen4 preset values per lane. Range: 0-9, 7 is default for each lane **/ UINT8 CpuPcieGen4EndPointPreset[20]; /** Offset 0x0C74 - Pcie Gen3 End port Hint values per lane Used for programming Pcie Gen3 Hint values per lane. Range: 0-6, 2 is default for each lane **/ UINT8 CpuPcieGen3EndPointHint[20]; /** Offset 0x0C88 - Pcie Gen4 End port Hint values per lane Used for programming Pcie Gen4 Hint values per lane. Range: 0-6, 2 is default for each lane **/ UINT8 CpuPcieGen4EndPointHint[20]; /** Offset 0x0C9C - Skip Cpu Fia Programming Skip Fia configuration and lock if enable. 0: Disable; 1: Enable. $EN_DIS **/ UINT8 CpuPcieSkipCpuFiaProgramming; /** Offset 0x0C9D - PCIE Disable RootPort Clock Gating Describes whether the PCI Express Clock Gating for each root port is enabled by platform modules. 0: Disable; 1: Enable. $EN_DIS **/ UINT8 CpuPcieDisableRootPortClockGating; /** Offset 0x0C9E - PCIE Disable RootPort Power Gating Describes whether the PCI Express Power Gating for each root port is enabled by platform modules. 0: Disable; 1: Enable. $EN_DIS **/ UINT8 CpuPcieDisableRootPortPowerGating; /** Offset 0x0C9F - PCIE Compliance Test Mode Compliance Test Mode shall be enabled when using Compliance Load Board. $EN_DIS **/ UINT8 CpuPcieComplianceTestMode; /** Offset 0x0CA0 - PCIE Secure Register Lock Describes whether Secure Register Lock is enaled or disabled. When it will be enbaled, load CpuPcieRpSetSecuredRegisterLock recipe. 0: Disable(Default); 1: Enable $EN_DIS **/ UINT8 CpuPcieSetSecuredRegisterLock; /** Offset 0x0CA1 - PCIE Enable Peer Memory Write This member describes whether Peer Memory Writes are enabled on the platform. $EN_DIS **/ UINT8 CpuPcieEnablePeerMemoryWrite; /** Offset 0x0CA2 - PCIE Rp Function Swap Allows BIOS to use root port function number swapping when root port of function 0 is disabled. $EN_DIS **/ UINT8 CpuPcieRpFunctionSwap; /** Offset 0x0CA3 **/ UINT8 UnusedUpdSpace44; /** Offset 0x0CA4 - Pch PCIE device override table pointer The PCIe device table is being used to override PCIe device ASPM settings. This is a pointer points to a 32bit address. And it's only used in PostMem phase. Please refer to CPU_PCIE_DEVICE_OVERRIDE structure for the table. Last entry VendorId must be 0. **/ UINT32 CpuPcieDeviceOverrideTablePtr; /** Offset 0x0CA8 - Enable PCIE RP HotPlug Indicate whether the root port is hot plug available. **/ UINT8 CpuPcieRpHotPlug[4]; /** Offset 0x0CAC - Enable PCIE RP Pm Sci Indicate whether the root port power manager SCI is enabled. **/ UINT8 CpuPcieRpPmSci[4]; /** Offset 0x0CB0 - Enable PCIE RP Transmitter Half Swing Indicate whether the Transmitter Half Swing is enabled. **/ UINT8 CpuPcieRpTransmitterHalfSwing[4]; /** Offset 0x0CB4 - PCIE RP Access Control Services Extended Capability Enable/Disable PCIE RP Access Control Services Extended Capability **/ UINT8 CpuPcieRpAcsEnabled[4]; /** Offset 0x0CB8 - PCIE RP Clock Power Management Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal can still be controlled by L1 PM substates mechanism **/ UINT8 CpuPcieRpEnableCpm[4]; /** Offset 0x0CBC - PCIE RP Advanced Error Report Indicate whether the Advanced Error Reporting is enabled. **/ UINT8 CpuPcieRpAdvancedErrorReporting[4]; /** Offset 0x0CC0 - PCIE RP Unsupported Request Report Indicate whether the Unsupported Request Report is enabled. **/ UINT8 CpuPcieRpUnsupportedRequestReport[4]; /** Offset 0x0CC4 - PCIE RP Fatal Error Report Indicate whether the Fatal Error Report is enabled. **/ UINT8 CpuPcieRpFatalErrorReport[4]; /** Offset 0x0CC8 - PCIE RP No Fatal Error Report Indicate whether the No Fatal Error Report is enabled. **/ UINT8 CpuPcieRpNoFatalErrorReport[4]; /** Offset 0x0CCC - PCIE RP Correctable Error Report Indicate whether the Correctable Error Report is enabled. **/ UINT8 CpuPcieRpCorrectableErrorReport[4]; /** Offset 0x0CD0 - PCIE RP System Error On Fatal Error Indicate whether the System Error on Fatal Error is enabled. **/ UINT8 CpuPcieRpSystemErrorOnFatalError[4]; /** Offset 0x0CD4 - PCIE RP System Error On Non Fatal Error Indicate whether the System Error on Non Fatal Error is enabled. **/ UINT8 CpuPcieRpSystemErrorOnNonFatalError[4]; /** Offset 0x0CD8 - PCIE RP System Error On Correctable Error Indicate whether the System Error on Correctable Error is enabled. **/ UINT8 CpuPcieRpSystemErrorOnCorrectableError[4]; /** Offset 0x0CDC - PCIE RP Max Payload Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD. **/ UINT8 CpuPcieRpMaxPayload[4]; /** Offset 0x0CE0 - DPC for PCIE RP Mask Enable/disable Downstream Port Containment for PCIE Root Ports. 0: disable, 1: enable. One bit for each port, bit0 for port1, bit1 for port2, and so on. **/ UINT8 CpuPcieRpDpcEnabled[4]; /** Offset 0x0CE4 - DPC Extensions PCIE RP Mask Enable/disable DPC Extensions for PCIE Root Ports. 0: disable, 1: enable. One bit for each port, bit0 for port1, bit1 for port2, and so on. **/ UINT8 CpuPcieRpDpcExtensionsEnabled[4]; /** Offset 0x0CE8 - PCH PCIe root port connection type 0: built-in device, 1:slot **/ UINT8 CpuPcieRpSlotImplemented[4]; /** Offset 0x0CEC - PCIE RP Gen3 Equalization Phase Method PCIe Gen3 Eq Ph3 Method (see CPU_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization; 1: hardware equalization; 4: Fixed Coeficients. **/ UINT8 CpuPcieRpGen3EqPh3Method[4]; /** Offset 0x0CF0 - PCIE RP Gen4 Equalization Phase Method PCIe Gen4 Eq Ph3 Method (see CPU_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization; 1: hardware equalization; 4: Fixed Coeficients. **/ UINT8 CpuPcieRpGen4EqPh3Method[4]; /** Offset 0x0CF4 - Phase3 RP Gen3 EQ enable Phase3 Gen3 EQ enable. Disabled(0x0): Disable phase 3, Enabled(0x1): Enable phase 3, Auto(0x2)(Default): Use the current default method 0:Disable, 1:Enable, 2:Auto **/ UINT8 CpuPcieRpGen3EqPh3Enable[4]; /** Offset 0x0CF8 - Phase3 RP Gen4 EQ enable Phase3 Gen4 EQ enable. Disabled(0x0): Disable phase 3, Enabled(0x1): Enable phase 3, Auto(0x2)(Default): Use the current default method 0:Disable, 1:Enable, 2:Auto **/ UINT8 CpuPcieRpGen4EqPh3Enable[4]; /** Offset 0x0CFC - Phase2-3 RP Gen3 EQ enable Phase2-3 Gen3 EQ enable. Disabled(0x0): Disable Phase2-3, Enabled(0x1): Enable Phase2-3, Auto(0x2)(Default): Use the current default method 0:Disable, 1:Enable, 2:Auto **/ UINT8 CpuPcieRpGen3EqPh23Enable[4]; /** Offset 0x0D00 - Phase2-3 RP Gen4 EQ enable Phase2-3 Gen4 EQ enable. Disabled(0x0): Disable Phase2-3, Enabled(0x1): Enable Phase2-3, Auto(0x2)(Default): Use the current default method 0:Disable, 1:Enable, 2:Auto **/ UINT8 CpuPcieRpGen4EqPh23Enable[4]; /** Offset 0x0D04 - PCET Timer Preset/Coefficient Evaluation Timeout. See CPU_PCIE_PCET. Default is 0x4 **/ UINT8 CpuPciePcetTimer[4]; /** Offset 0x0D08 - Gen3 Preset/Coeffiecient List Count Select Gen3 Hardware Autonomous Preset/Coefficient Count. See Gen3 CPU_PCIE_PRESETCOEFF_LIST. Default is 0x3 **/ UINT8 Gen3CpuPciePresetCoeffList[4]; /** Offset 0x0D0C - Gen4 Preset/Coeffiecient List Count Select Gen4 Hardware Autonomous Preset/Coefficient Count. See CPU_PCIE_PRESETCOEFF_LIST. Default is 0x3 **/ UINT8 Gen4CpuPciePresetCoeffList[4]; /** Offset 0x0D10 - Presets/Coefficients Evaluation for Gen3 8.0GT/s Training Sequence Wait Latency For Presets/Coefficients Evaluation. See CPU_PCIE_PX8GTSWLPCE. Default is 0x3 **/ UINT8 CpuPciePx8gtswlpce[4]; /** Offset 0x0D14 - Presets/Coefficients Evaluation for Gen4 16.0GT/s Training Sequence Wait Latency For Presets/Coefficients Evaluation. See CPU_PCIE_PX16GTSWLPCE. Default is 0x4 **/ UINT8 CpuPciePx16gtswlpce[4]; /** Offset 0x0D18 - PCIE RP Physical Slot Number Indicates the slot number for the root port. Default is the value as root port index. **/ UINT8 CpuPcieRpPhysicalSlotNumber[4]; /** Offset 0x0D1C - PCIE RP Aspm The ASPM configuration of the root port (see: CPU_PCIE_ASPM_CONTROL). Default is CpuPcieAspmAutoConfig. **/ UINT8 CpuPcieRpAspm[4]; /** Offset 0x0D20 - PCIE RP L1 Substates The L1 Substates configuration of the root port (see: CPU_PCIE_L1SUBSTATES_CONTROL). Default is CpuPcieL1SubstatesDisabled. **/ UINT8 CpuPcieRpL1Substates[4]; /** Offset 0x0D24 - PCIE RP Ltr Enable Latency Tolerance Reporting Mechanism. **/ UINT8 CpuPcieRpLtrEnable[4]; /** Offset 0x0D28 - PCIE RP Ltr Config Lock 0: Disable; 1: Enable. **/ UINT8 CpuPcieRpLtrConfigLock[4]; /** Offset 0x0D2C - PTM for PCIE RP Mask Enable/disable Precision Time Measurement for PCIE Root Ports. 0: disable, 1: enable. One bit for each port, bit0 for port1, bit1 for port2, and so on. **/ UINT8 CpuPcieRpPtmEnabled[4]; /** Offset 0x0D30 - PCIE RP Detect Timeout Ms The number of milliseconds within 0~65535 in reference code will wait for link to exit Detect state for enabled ports before assuming there is no device and potentially disabling the port. **/ UINT16 CpuPcieRpDetectTimeoutMs[4]; /** Offset 0x0D38 - VC for PCIE RP Mask Enable/disable Virtual Channel for PCIE Root Ports. 0: disable, 1: enable. One bit for each port, bit0 for port1, bit1 for port2, and so on. **/ UINT8 CpuPcieRpVcEnabled[4]; /** Offset 0x0D3C - Force GT CLOS on LLC for Real Time Performance 0(Default)=Disable, 1=Enable $EN_DIS **/ UINT8 GtClosEnable; /** Offset 0x0D3D - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3 Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3, Each value in array can be between 0-1. One byte for each port. **/ UINT8 Usb3HsioTxRate3UniqTranEnable[10]; /** Offset 0x0D47 - USB 3.0 TX Output Unique Transition Bit Scale for rate 3 USB 3.0 TX Output Unique Transition Bit Scale for rate 3, HSIO_TX_DWORD9[6:0], Default = 4Ch. One byte for each port. **/ UINT8 Usb3HsioTxRate3UniqTran[10]; /** Offset 0x0D51 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2 Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2, Each value in array can be between 0-1. One byte for each port. **/ UINT8 Usb3HsioTxRate2UniqTranEnable[10]; /** Offset 0x0D5B - USB 3.0 TX Output Unique Transition Bit Scale for rate 2 USB 3.0 TX Output Unique Transition Bit Scale for rate 2, HSIO_TX_DWORD9[14:8], Default = 4Ch. One byte for each port. **/ UINT8 Usb3HsioTxRate2UniqTran[10]; /** Offset 0x0D65 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1 Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1, Each value in array can be between 0-1. One byte for each port. **/ UINT8 Usb3HsioTxRate1UniqTranEnable[10]; /** Offset 0x0D6F - USB 3.0 TX Output Unique Transition Bit Scale for rate 1 USB 3.0 TX Output Unique Transition Bit Scale for rate 1, HSIO_TX_DWORD9[22:16], Default = 4Ch. One byte for each port. **/ UINT8 Usb3HsioTxRate1UniqTran[10]; /** Offset 0x0D79 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0 Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0, Each value in array can be between 0-1. One byte for each port. **/ UINT8 Usb3HsioTxRate0UniqTranEnable[10]; /** Offset 0x0D83 - USB 3.0 TX Output Unique Transition Bit Scale for rate 0 USB 3.0 TX Output Unique Transition Bit Scale for rate 0, HSIO_TX_DWORD9[30:24], Default = 4Ch. One byte for each port. **/ UINT8 Usb3HsioTxRate0UniqTran[10]; /** Offset 0x0D8D - Skip PAM regsiter lock Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default): PAM registers will be locked by RC $EN_DIS **/ UINT8 SkipPamLock; /** Offset 0x0D8E - EDRAM Test Mode Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default): PAM registers will be locked by RC 0: EDRAM SW disable, 1: EDRAM SW Enable, 2: EDRAM HW mode **/ UINT8 EdramTestMode; /** Offset 0x0D8F - Enable/Disable IGFX RenderStandby Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby $EN_DIS **/ UINT8 RenderStandby; /** Offset 0x0D90 - Enable/Disable IGFX PmSupport Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport $EN_DIS **/ UINT8 PmSupport; /** Offset 0x0D91 - Enable/Disable CdynmaxClamp Enable: Enable CdynmaxClamp, Disable(Default): Disable CdynmaxClamp $EN_DIS **/ UINT8 CdynmaxClampEnable; /** Offset 0x0D92 - GT Frequency Limit 0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz, 7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD: 650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz, 0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz, 0x18: 1200 Mhz 0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz, 7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD: 650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz, 0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz, 0x18: 1200 Mhz **/ UINT8 GtFreqMax; /** Offset 0x0D93 - Disable Turbo GT 0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency $EN_DIS **/ UINT8 DisableTurboGt; /** Offset 0x0D94 - Enable/Disable CdClock Init Enable: Skip Full CD clock initializaton, Disable(Default): Initialize the full CD clock if not initialized by Gfx PEIM $EN_DIS **/ UINT8 SkipCdClockInit; /** Offset 0x0D95 **/ UINT8 UnusedUpdSpace45[3]; /** Offset 0x0D98 - LogoPixelHeight Address Address of LogoPixelHeight **/ UINT32 LogoPixelHeight; /** Offset 0x0D9C - LogoPixelWidth Address Address of LogoPixelWidth **/ UINT32 LogoPixelWidth; /** Offset 0x0DA0 - SaPostMemTestRsvd Reserved for SA Post-Mem Test $EN_DIS **/ UINT8 SaPostMemTestRsvd[6]; /** Offset 0x0DA6 - RSR feature Enable or Disable RSR feature; 0: Disable; 1: Enable $EN_DIS **/ UINT8 EnableRsr; /** Offset 0x0DA7 - 1-Core Ratio Limit 1-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused 1-Core Ratio Limit + OC Bins.This 1-Core Ratio Limit Must be greater than or equal to 2-Core Ratio Limit, 3-Core Ratio Limit, 4-Core Ratio Limit. Range is 0 to 83 **/ UINT8 OneCoreRatioLimit; /** Offset 0x0DA8 - 2-Core Ratio Limit 2-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused 2-Core Ratio Limit + OC Bins.This 2-Core Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 83 **/ UINT8 TwoCoreRatioLimit; /** Offset 0x0DA9 - 3-Core Ratio Limit 3-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused 3-Core Ratio Limit + OC Bins.This 3-Core Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 83 **/ UINT8 ThreeCoreRatioLimit; /** Offset 0x0DAA - 4-Core Ratio Limit 4-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused 4-Core Ratio Limit + OC Bins.This 4-Core Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 83 **/ UINT8 FourCoreRatioLimit; /** Offset 0x0DAB - Enable or Disable HWP Enable or Disable HWP(Hardware P states) Support. 0: Disable; 1: Enable; 2-3:Reserved $EN_DIS **/ UINT8 Hwp; /** Offset 0x0DAC - Hardware Duty Cycle Control Hardware Duty Cycle Control configuration. 0: Disabled; 1: Enabled 2-3:Reserved $EN_DIS **/ UINT8 HdcControl; /** Offset 0x0DAD - Package Long duration turbo mode time Package Long duration turbo mode time window in seconds. Valid values(Unit in seconds) 0 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128 **/ UINT8 PowerLimit1Time; /** Offset 0x0DAE - Short Duration Turbo Mode Enable or Disable short duration Turbo Mode. 0 : Disable; 1: Enable $EN_DIS **/ UINT8 PowerLimit2; /** Offset 0x0DAF - Turbo settings Lock Lock all Turbo settings Enable/Disable; 0: Disable , 1: Enable $EN_DIS **/ UINT8 TurboPowerLimitLock; /** Offset 0x0DB0 - Package PL3 time window Package PL3 time window range for this policy from 0 to 64ms **/ UINT8 PowerLimit3Time; /** Offset 0x0DB1 - Package PL3 Duty Cycle Package PL3 Duty Cycle; Valid Range is 0 to 100 **/ UINT8 PowerLimit3DutyCycle; /** Offset 0x0DB2 - Package PL3 Lock Package PL3 Lock Enable/Disable; 0: Disable ; 1:Enable $EN_DIS **/ UINT8 PowerLimit3Lock; /** Offset 0x0DB3 - Package PL4 Lock Package PL4 Lock Enable/Disable; 0: Disable ; 1:Enable $EN_DIS **/ UINT8 PowerLimit4Lock; /** Offset 0x0DB4 - TCC Activation Offset TCC Activation Offset. Offset from factory set TCC activation temperature at which the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation Temperature, in volts.For SKL Y SKU, the recommended default for this policy is 10, For all other SKUs the recommended default are 0 **/ UINT8 TccActivationOffset; /** Offset 0x0DB5 - Tcc Offset Clamp Enable/Disable Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle below P1.For SKL Y SKU, the recommended default for this policy is 1: Enabled, For all other SKUs the recommended default are 0: Disabled. $EN_DIS **/ UINT8 TccOffsetClamp; /** Offset 0x0DB6 - Tcc Offset Lock Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature target; 0: Disabled; 1: Enabled. $EN_DIS **/ UINT8 TccOffsetLock; /** Offset 0x0DB7 - Custom Ratio State Entries The number of custom ratio state entries, ranges from 0 to 40 for a valid custom ratio table.Sets the number of custom P-states. At least 2 states must be present **/ UINT8 NumberOfEntries; /** Offset 0x0DB8 - Custom Short term Power Limit time window Short term Power Limit time window value for custom CTDP level 1. Valid Range 0 to 128 **/ UINT8 Custom1PowerLimit1Time; /** Offset 0x0DB9 - Custom Turbo Activation Ratio Turbo Activation Ratio for custom cTDP level 1. Valid Range 0 to 255 **/ UINT8 Custom1TurboActivationRatio; /** Offset 0x0DBA - Custom Config Tdp Control Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2 **/ UINT8 Custom1ConfigTdpControl; /** Offset 0x0DBB - Custom Short term Power Limit time window Short term Power Limit time window value for custom CTDP level 2. Valid Range 0 to 128 **/ UINT8 Custom2PowerLimit1Time; /** Offset 0x0DBC - Custom Turbo Activation Ratio Turbo Activation Ratio for custom cTDP level 2. Valid Range 0 to 255 **/ UINT8 Custom2TurboActivationRatio; /** Offset 0x0DBD - Custom Config Tdp Control Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2 **/ UINT8 Custom2ConfigTdpControl; /** Offset 0x0DBE - Custom Short term Power Limit time window Short term Power Limit time window value for custom CTDP level 3. Valid Range 0 to 128 **/ UINT8 Custom3PowerLimit1Time; /** Offset 0x0DBF - Custom Turbo Activation Ratio Turbo Activation Ratio for custom cTDP level 3. Valid Range 0 to 255 **/ UINT8 Custom3TurboActivationRatio; /** Offset 0x0DC0 - Custom Config Tdp Control Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2 **/ UINT8 Custom3ConfigTdpControl; /** Offset 0x0DC1 - ConfigTdp mode settings Lock Lock the ConfigTdp mode settings from runtime changes; 0: Disable; 1: Enable $EN_DIS **/ UINT8 ConfigTdpLock; /** Offset 0x0DC2 - Load Configurable TDP SSDT Configure whether to load Configurable TDP SSDT; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 ConfigTdpBios; /** Offset 0x0DC3 - PL1 Enable value PL1 Enable value to limit average platform power. 0: Disable; 1: Enable. $EN_DIS **/ UINT8 PsysPowerLimit1; /** Offset 0x0DC4 - PL1 timewindow PL1 timewindow in seconds.Valid values(Unit in seconds) 0 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128 **/ UINT8 PsysPowerLimit1Time; /** Offset 0x0DC5 - PL2 Enable Value PL2 Enable activates the PL2 value to limit average platform power.0: Disable; 1: Enable. $EN_DIS **/ UINT8 PsysPowerLimit2; /** Offset 0x0DC6 - Enable or Disable MLC Streamer Prefetcher Enable or Disable MLC Streamer Prefetcher; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 MlcStreamerPrefetcher; /** Offset 0x0DC7 - Enable or Disable MLC Spatial Prefetcher Enable or Disable MLC Spatial Prefetcher; 0: Disable; 1: Enable $EN_DIS **/ UINT8 MlcSpatialPrefetcher; /** Offset 0x0DC8 - Enable or Disable Monitor /MWAIT instructions Enable or Disable Monitor /MWAIT instructions; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 MonitorMwaitEnable; /** Offset 0x0DC9 - Enable or Disable initialization of machine check registers Enable or Disable initialization of machine check registers; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 MachineCheckEnable; /** Offset 0x0DCA - Check if FUSA is supported Check if FUSA is supported; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 IsFusaSupported; /** Offset 0x0DCB - AP Idle Manner of waiting for SIPI AP Idle Manner of waiting for SIPI; 1: HALT loop; 2: MWAIT loop; 3: RUN loop. 1: HALT loop, 2: MWAIT loop, 3: RUN loop **/ UINT8 ApIdleManner; /** Offset 0x0DCC - Control on Processor Trace output scheme Control on Processor Trace output scheme; 0: Single Range Output; 1: ToPA Output. 0: Single Range Output, 1: ToPA Output **/ UINT8 ProcessorTraceOutputScheme; /** Offset 0x0DCD - Enable or Disable Processor Trace feature Enable or Disable Processor Trace feature; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 ProcessorTraceEnable; /** Offset 0x0DCE - Enable or Disable Intel SpeedStep Technology Enable or Disable Intel SpeedStep Technology. 0: Disable; 1: Enable $EN_DIS **/ UINT8 Eist; /** Offset 0x0DCF - Enable or Disable Energy Efficient P-state Enable or Disable Energy Efficient P-state will be applied in Turbo mode. Disable; 1: Enable $EN_DIS **/ UINT8 EnergyEfficientPState; /** Offset 0x0DD0 - Enable or Disable Energy Efficient Turbo Enable or Disable Energy Efficient Turbo, will be applied in Turbo mode. Disable; 1: Enable $EN_DIS **/ UINT8 EnergyEfficientTurbo; /** Offset 0x0DD1 - Enable or Disable T states Enable or Disable T states; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 TStates; /** Offset 0x0DD2 - Enable or Disable Bi-Directional PROCHOT# Enable or Disable Bi-Directional PROCHOT#; 0: Disable; 1: Enable $EN_DIS **/ UINT8 BiProcHot; /** Offset 0x0DD3 - Enable or Disable PROCHOT# signal being driven externally Enable or Disable PROCHOT# signal being driven externally; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 DisableProcHotOut; /** Offset 0x0DD4 - Enable or Disable PROCHOT# Response Enable or Disable PROCHOT# Response; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 ProcHotResponse; /** Offset 0x0DD5 - Enable or Disable VR Thermal Alert Enable or Disable VR Thermal Alert; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 DisableVrThermalAlert; /** Offset 0x0DD6 - Enable or Disable Thermal Reporting Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 EnableAllThermalFunctions; /** Offset 0x0DD7 - Enable or Disable Thermal Monitor Enable or Disable Thermal Monitor; 0: Disable; 1: Enable $EN_DIS **/ UINT8 ThermalMonitor; /** Offset 0x0DD8 - Enable or Disable CPU power states (C-states) Enable or Disable CPU power states (C-states). 0: Disable; 1: Enable $EN_DIS **/ UINT8 Cx; /** Offset 0x0DD9 - Configure C-State Configuration Lock Configure C-State Configuration Lock; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 PmgCstCfgCtrlLock; /** Offset 0x0DDA - Enable or Disable Enhanced C-states Enable or Disable Enhanced C-states. 0: Disable; 1: Enable $EN_DIS **/ UINT8 C1e; /** Offset 0x0DDB - Enable or Disable Package Cstate Demotion Enable or Disable Package Cstate Demotion. 0: Disable; 1: Enable $EN_DIS **/ UINT8 PkgCStateDemotion; /** Offset 0x0DDC - Enable or Disable Package Cstate UnDemotion Enable or Disable Package Cstate UnDemotion. 0: Disable; 1: Enable $EN_DIS **/ UINT8 PkgCStateUnDemotion; /** Offset 0x0DDD - Enable or Disable CState-Pre wake Enable or Disable CState-Pre wake. 0: Disable; 1: Enable $EN_DIS **/ UINT8 CStatePreWake; /** Offset 0x0DDE - Enable or Disable TimedMwait Support. Enable or Disable TimedMwait Support. 0: Disable; 1: Enable $EN_DIS **/ UINT8 TimedMwait; /** Offset 0x0DDF - Enable or Disable IO to MWAIT redirection Enable or Disable IO to MWAIT redirection; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 CstCfgCtrIoMwaitRedirection; /** Offset 0x0DE0 - Set the Max Pkg Cstate Set the Max Pkg Cstate. Default set to Auto which limits the Max Pkg Cstate to deep C-state. Valid values 0 - C0/C1 , 1 - C2 , 2 - C3 , 3 - C6 , 4 - C7 , 5 - C7S , 6 - C8 , 7 - C9 , 8 - C10 , 254 - CPU Default , 255 - Auto **/ UINT8 PkgCStateLimit; /** Offset 0x0DE1 - TimeUnit for C-State Latency Control0 TimeUnit for C-State Latency Control0; Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns **/ UINT8 CstateLatencyControl0TimeUnit; /** Offset 0x0DE2 - TimeUnit for C-State Latency Control1 TimeUnit for C-State Latency Control1;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns **/ UINT8 CstateLatencyControl1TimeUnit; /** Offset 0x0DE3 - TimeUnit for C-State Latency Control2 TimeUnit for C-State Latency Control2;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns **/ UINT8 CstateLatencyControl2TimeUnit; /** Offset 0x0DE4 - TimeUnit for C-State Latency Control3 TimeUnit for C-State Latency Control3;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns **/ UINT8 CstateLatencyControl3TimeUnit; /** Offset 0x0DE5 - TimeUnit for C-State Latency Control4 Time - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns **/ UINT8 CstateLatencyControl4TimeUnit; /** Offset 0x0DE6 - TimeUnit for C-State Latency Control5 TimeUnit for C-State Latency Control5;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns **/ UINT8 CstateLatencyControl5TimeUnit; /** Offset 0x0DE7 - Interrupt Redirection Mode Select Interrupt Redirection Mode Select.0: Fixed priority; 1: Round robin;2: Hash vector;7: No change. **/ UINT8 PpmIrmSetting; /** Offset 0x0DE8 - Lock prochot configuration Lock prochot configuration Enable/Disable; 0: Disable; 1: Enable $EN_DIS **/ UINT8 ProcHotLock; /** Offset 0x0DE9 - Configuration for boot TDP selection Configuration for boot TDP selection; 0: TDP Nominal; 1: TDP Down; 2: TDP Up;0xFF : Deactivate **/ UINT8 ConfigTdpLevel; /** Offset 0x0DEA - Max P-State Ratio Max P-State Ratio, Valid Range 0 to 0x7F **/ UINT8 MaxRatio; /** Offset 0x0DEB - P-state ratios for custom P-state table P-state ratios for custom P-state table. NumberOfEntries has valid range between 0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries] are configurable. Valid Range of each entry is 0 to 0x7F **/ UINT8 StateRatio[40]; /** Offset 0x0E13 - P-state ratios for max 16 version of custom P-state table P-state ratios for max 16 version of custom P-state table. This table is used for OS versions limited to a max of 16 P-States. If the first entry of this table is 0, or if Number of Entries is 16 or less, then this table will be ignored, and up to the top 16 values of the StateRatio table will be used instead. Valid Range of each entry is 0 to 0x7F **/ UINT8 StateRatioMax16[16]; /** Offset 0x0E23 **/ UINT8 UnusedUpdSpace46; /** Offset 0x0E24 - Platform Power Pmax PCODE MMIO Mailbox: Platform Power Pmax. 0 - Auto Specified in 1/8 Watt increments. Range 0-1024 Watts. Value of 800 = 100W **/ UINT16 PsysPmax; /** Offset 0x0E26 - Interrupt Response Time Limit of C-State LatencyContol1 Interrupt Response Time Limit of C-State LatencyContol1.Range of value 0 to 0x3FF. 0 is Auto. **/ UINT16 CstateLatencyControl1Irtl; /** Offset 0x0E28 - Interrupt Response Time Limit of C-State LatencyContol2 Interrupt Response Time Limit of C-State LatencyContol2.Range of value 0 to 0x3FF. 0 is Auto. **/ UINT16 CstateLatencyControl2Irtl; /** Offset 0x0E2A - Interrupt Response Time Limit of C-State LatencyContol3 Interrupt Response Time Limit of C-State LatencyContol3.Range of value 0 to 0x3FF. 0 is Auto. **/ UINT16 CstateLatencyControl3Irtl; /** Offset 0x0E2C - Interrupt Response Time Limit of C-State LatencyContol4 Interrupt Response Time Limit of C-State LatencyContol4.Range of value 0 to 0x3FF. 0 is Auto. **/ UINT16 CstateLatencyControl4Irtl; /** Offset 0x0E2E - Interrupt Response Time Limit of C-State LatencyContol5 Interrupt Response Time Limit of C-State LatencyContol5.Range of value 0 to 0x3FF. 0 is Auto. **/ UINT16 CstateLatencyControl5Irtl; /** Offset 0x0E30 - Package Long duration turbo mode power limit Package Long duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 PowerLimit1; /** Offset 0x0E34 - Package Short duration turbo mode power limit Package Short duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 PowerLimit2Power; /** Offset 0x0E38 - Package PL3 power limit Package PL3 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 PowerLimit3; /** Offset 0x0E3C - Package PL4 power limit Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 PowerLimit4; /** Offset 0x0E40 - Tcc Offset Time Window for RATL Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 TccOffsetTimeWindowForRatl; /** Offset 0x0E44 - Short term Power Limit value for custom cTDP level 1 Short term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 Custom1PowerLimit1; /** Offset 0x0E48 - Long term Power Limit value for custom cTDP level 1 Long term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 Custom1PowerLimit2; /** Offset 0x0E4C - Short term Power Limit value for custom cTDP level 2 Short term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 Custom2PowerLimit1; /** Offset 0x0E50 - Long term Power Limit value for custom cTDP level 2 Long term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 Custom2PowerLimit2; /** Offset 0x0E54 - Short term Power Limit value for custom cTDP level 3 Short term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 Custom3PowerLimit1; /** Offset 0x0E58 - Long term Power Limit value for custom cTDP level 3 Long term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 Custom3PowerLimit2; /** Offset 0x0E5C - Platform PL1 power Platform PL1 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 PsysPowerLimit1Power; /** Offset 0x0E60 - Platform PL2 power Platform PL2 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range 0 to 4095875 in Step size of 125 **/ UINT32 PsysPowerLimit2Power; /** Offset 0x0E64 - Race To Halt Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency in order to enter pkg C-State faster to reduce overall power. (RTH is controlled through MSR 1FC bit 20)Disable; 1: Enable $EN_DIS **/ UINT8 RaceToHalt; /** Offset 0x0E65 - Set Three Strike Counter Disable False (default): Three Strike counter will be incremented and True: Prevents Three Strike counter from incrementing; 0: False; 1: True. 0: False, 1: True **/ UINT8 ThreeStrikeCounterDisable; /** Offset 0x0E66 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; 0: Disable; 1: Enable. $EN_DIS **/ UINT8 HwpInterruptControl; /** Offset 0x0E67 - 5-Core Ratio Limit 5-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused 5-Core Ratio Limit + OC Bins.This 5-Core Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 83 0x0:0xFF **/ UINT8 FiveCoreRatioLimit; /** Offset 0x0E68 - 6-Core Ratio Limit 6-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused 6-Core Ratio Limit + OC Bins.This 6-Core Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 83 0x0:0xFF **/ UINT8 SixCoreRatioLimit; /** Offset 0x0E69 - 7-Core Ratio Limit 7-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused 7-Core Ratio Limit + OC Bins.This 7-Core Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 83 0x0:0xFF **/ UINT8 SevenCoreRatioLimit; /** Offset 0x0E6A - 8-Core Ratio Limit 8-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused 8-Core Ratio Limit + OC Bins.This 8-Core Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 83 0x0:0xFF **/ UINT8 EightCoreRatioLimit; /** Offset 0x0E6B - Intel Turbo Boost Max Technology 3.0 Intel Turbo Boost Max Technology 3.0. 0: Disabled; 1: Enabled $EN_DIS **/ UINT8 EnableItbm; /** Offset 0x0E6C - Intel Turbo Boost Max Technology 3.0 Driver Intel Turbo Boost Max Technology 3.0 Driver 0: Disabled; 1: Enabled $EN_DIS **/ UINT8 EnableItbmDriver; /** Offset 0x0E6D - Enable or Disable C1 Cstate Demotion Enable or Disable C1 Cstate Demotion. Disable; 1: Enable $EN_DIS **/ UINT8 C1StateAutoDemotion; /** Offset 0x0E6E - Enable or Disable C1 Cstate UnDemotion Enable or Disable C1 Cstate UnDemotion. Disable; 1: Enable $EN_DIS **/ UINT8 C1StateUnDemotion; /** Offset 0x0E6F - Minimum Ring ratio limit override Minimum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo ratio limit **/ UINT8 MinRingRatioLimit; /** Offset 0x0E70 - Maximum Ring ratio limit override Maximum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo ratio limit **/ UINT8 MaxRingRatioLimit; /** Offset 0x0E71 - Enable or Disable Per Core P State OS control Enable or Disable Per Core P State OS control. 0: Disable; 1: Enable $EN_DIS **/ UINT8 EnablePerCorePState; /** Offset 0x0E72 - Enable or Disable HwP Autonomous Per Core P State OS control Enable or Disable HwP Autonomous Per Core P State OS control. 0: Disable; 1: Enable $EN_DIS **/ UINT8 EnableHwpAutoPerCorePstate; /** Offset 0x0E73 - Enable or Disable HwP Autonomous EPP Grouping Enable or Disable HwP Autonomous EPP Grouping. 0: Disable; 1: Enable $EN_DIS **/ UINT8 EnableHwpAutoEppGrouping; /** Offset 0x0E74 - Enable or Disable EPB override over PECI Enable or Disable EPB override over PECI. 0: Disable; 1: Enable $EN_DIS **/ UINT8 EnableEpbPeciOverride; /** Offset 0x0E75 - Enable or Disable Fast MSR for IA32_HWP_REQUEST Enable or Disable Fast MSR for IA32_HWP_REQUEST. 0: Disable; 1: Enable $EN_DIS **/ UINT8 EnableFastMsrHwpReq; /** Offset 0x0E76 - Enable Configurable TDP Applies TDP initialization settings based on non-cTDP or cTDP.; 0: Applies to non-cTDP; 1: Applies to cTDP $EN_DIS **/ UINT8 ApplyConfigTdp; /** Offset 0x0E77 - ReservedCpuPostMemTest Reserved for CPU Post-Mem Test $EN_DIS **/ UINT8 ReservedCpuPostMemTest[16]; /** Offset 0x0E87 **/ UINT8 SecurityPostMemRsvd[16]; /** Offset 0x0E97 - D0I3 Setting for HECI Disable Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all HECI devices $EN_DIS **/ UINT8 DisableD0I3SettingForHeci; /** Offset 0x0E98 - Enable LOCKDOWN SMI Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit. $EN_DIS **/ UINT8 PchLockDownGlobalSmi; /** Offset 0x0E99 - Enable LOCKDOWN BIOS Interface Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register. $EN_DIS **/ UINT8 PchLockDownBiosInterface; /** Offset 0x0E9A - Unlock all GPIO pads Force all GPIO pads to be unlocked for debug purpose. $EN_DIS **/ UINT8 PchUnlockGpioPads; /** Offset 0x0E9B - PCH Unlock SideBand access The SideBand PortID mask for certain end point (e.g. PSFx) will be locked before 3rd party code execution. 0: Lock SideBand access; 1: Unlock SideBand access. $EN_DIS **/ UINT8 PchSbAccessUnlock; /** Offset 0x0E9C - PCIE RP Ltr Max Snoop Latency Latency Tolerance Reporting, Max Snoop Latency. **/ UINT16 PcieRpLtrMaxSnoopLatency[24]; /** Offset 0x0ECC - PCIE RP Ltr Max No Snoop Latency Latency Tolerance Reporting, Max Non-Snoop Latency. **/ UINT16 PcieRpLtrMaxNoSnoopLatency[24]; /** Offset 0x0EFC - PCIE RP Snoop Latency Override Mode Latency Tolerance Reporting, Snoop Latency Override Mode. **/ UINT8 PcieRpSnoopLatencyOverrideMode[24]; /** Offset 0x0F14 - PCIE RP Snoop Latency Override Multiplier Latency Tolerance Reporting, Snoop Latency Override Multiplier. **/ UINT8 PcieRpSnoopLatencyOverrideMultiplier[24]; /** Offset 0x0F2C - PCIE RP Snoop Latency Override Value Latency Tolerance Reporting, Snoop Latency Override Value. **/ UINT16 PcieRpSnoopLatencyOverrideValue[24]; /** Offset 0x0F5C - PCIE RP Non Snoop Latency Override Mode Latency Tolerance Reporting, Non-Snoop Latency Override Mode. **/ UINT8 PcieRpNonSnoopLatencyOverrideMode[24]; /** Offset 0x0F74 - PCIE RP Non Snoop Latency Override Multiplier Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier. **/ UINT8 PcieRpNonSnoopLatencyOverrideMultiplier[24]; /** Offset 0x0F8C - PCIE RP Non Snoop Latency Override Value Latency Tolerance Reporting, Non-Snoop Latency Override Value. **/ UINT16 PcieRpNonSnoopLatencyOverrideValue[24]; /** Offset 0x0FBC - PCIE RP Slot Power Limit Scale Specifies scale used for slot power limit value. Leave as 0 to set to default. **/ UINT8 PcieRpSlotPowerLimitScale[24]; /** Offset 0x0FD4 - PCIE RP Slot Power Limit Value Specifies upper limit on power supplie by slot. Leave as 0 to set to default. **/ UINT16 PcieRpSlotPowerLimitValue[24]; /** Offset 0x1004 - PCIE RP Enable Port8xh Decode This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable; 1: Enable. $EN_DIS **/ UINT8 PcieEnablePort8xhDecode; /** Offset 0x1005 - PCIE Port8xh Decode Port Index The Index of PCIe Port that is selected for Port8xh Decode (0 Based). **/ UINT8 PchPciePort8xhDecodePortIndex; /** Offset 0x1006 - PCH Energy Reporting Disable/Enable PCH to CPU energy report feature. $EN_DIS **/ UINT8 PchPmDisableEnergyReport; /** Offset 0x1007 - PCH Sata Test Mode Allow entrance to the PCH SATA test modes. $EN_DIS **/ UINT8 SataTestMode; /** Offset 0x1008 - PCH USB OverCurrent mapping lock enable If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning that OC mapping data will be consumed by xHCI and OC mapping registers will be locked. $EN_DIS **/ UINT8 PchXhciOcLock; /** Offset 0x1009 - Low Power Mode Enable/Disable config mask Configure if respective S0i2/3 sub-states are to be supported. Each bit corresponds to one sub-state (LPMx - BITx): LPM0-s0i2.0, LPM1-s0i2.1, LPM2-s0i2.2, LPM3-s0i3.0, LPM4-s0i3.1, LPM5-s0i3.2, LPM6-s0i3.3, LPM7-s0i3.4. **/ UINT8 PmcLpmS0ixSubStateEnableMask; /** Offset 0x100A - Mctp Broadcast Cycle Test, Determine if MCTP Broadcast is enabled 0: Disable; 1: Enable. $EN_DIS **/ UINT8 MctpBroadcastCycle; /** Offset 0x100B **/ UINT8 UnusedUpdSpace47[1]; /** Offset 0x100C - PCIE RP Ltr Max Snoop Latency Latency Tolerance Reporting, Max Snoop Latency. **/ UINT16 CpuPcieRpLtrMaxSnoopLatency[4]; /** Offset 0x1014 - PCIE RP Ltr Max No Snoop Latency Latency Tolerance Reporting, Max Non-Snoop Latency. **/ UINT16 CpuPcieRpLtrMaxNoSnoopLatency[4]; /** Offset 0x101C - PCIE RP Snoop Latency Override Mode Latency Tolerance Reporting, Snoop Latency Override Mode. **/ UINT8 CpuPcieRpSnoopLatencyOverrideMode[4]; /** Offset 0x1020 - PCIE RP Snoop Latency Override Multiplier Latency Tolerance Reporting, Snoop Latency Override Multiplier. **/ UINT8 CpuPcieRpSnoopLatencyOverrideMultiplier[4]; /** Offset 0x1024 - PCIE RP Snoop Latency Override Value Latency Tolerance Reporting, Snoop Latency Override Value. **/ UINT16 CpuPcieRpSnoopLatencyOverrideValue[4]; /** Offset 0x102C - PCIE RP Non Snoop Latency Override Mode Latency Tolerance Reporting, Non-Snoop Latency Override Mode. **/ UINT8 CpuPcieRpNonSnoopLatencyOverrideMode[4]; /** Offset 0x1030 - PCIE RP Non Snoop Latency Override Multiplier Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier. **/ UINT8 CpuPcieRpNonSnoopLatencyOverrideMultiplier[4]; /** Offset 0x1034 - PCIE RP Non Snoop Latency Override Value Latency Tolerance Reporting, Non-Snoop Latency Override Value. **/ UINT16 CpuPcieRpNonSnoopLatencyOverrideValue[4]; /** Offset 0x103C - PCIE RP Upstream Port Transmiter Preset Used during Gen3 Link Equalization. Used for all lanes. Default is 7. **/ UINT8 CpuPcieRpGen3Uptp[4]; /** Offset 0x1040 - PCIE RP Downstream Port Transmiter Preset Used during Gen3 Link Equalization. Used for all lanes. Default is 7. **/ UINT8 CpuPcieRpGen3Dptp[4]; /** Offset 0x1044 - PCIE RP Upstream Port Transmiter Preset Used during Gen3 Link Equalization. Used for all lanes. Default is 7. **/ UINT8 CpuPcieRpGen4Uptp[4]; /** Offset 0x1048 - PCIE RP Downstream Port Transmiter Preset Used during Gen3 Link Equalization. Used for all lanes. Default is 7. **/ UINT8 CpuPcieRpGen4Dptp[4]; /** Offset 0x104C - Enable PSE JTAG debug option Set if to enable JTAG debug feature for PSE. 0: Disable; 1: Enable. **/ UINT8 PchPseJtagEnabled; /** Offset 0x104D - Enable PSE JTAG pin option This option is used to enable or disable PSE JTAG pin pad mode. 0: Disable; 1: Enable. **/ UINT8 PchPseJtagPinMux; /** Offset 0x104E - Enable PSE SHELL option Set if to enable PSE Shell feature. 0: Disable; 1: Enable. **/ UINT8 PchPseShellEnabled; /** Offset 0x104F - Enable PSE ECLITE option Set if to enable PSE Eclite feature. 0: Disable; 1: Enable. **/ UINT8 PchPseEcliteEnabled; /** Offset 0x1050 - Enable PSE OOB option Set if to enable PSE OOB feature. 0: Disable; 1: Enable. **/ UINT8 PchPseOobEnabled; /** Offset 0x1051 - Enable CPU Temperature Read Set to enable CPU Temperature Read feature. 0: Disable; 1: Enable. **/ UINT8 PchCpuTempSensorEnable; /** Offset 0x1052 - Enable PSE WoL option Set if to enable PSE WoL feature. 0: Disable; 1: Enable. **/ UINT8 PchPseWoLEnabled; /** Offset 0x1053 **/ UINT8 ReservedFspsUpd[13]; } FSP_S_CONFIG; /** Fsp S UPD Configuration **/ typedef struct { /** Offset 0x0000 **/ FSP_UPD_HEADER FspUpdHeader; /** Offset 0x0020 **/ FSP_S_CONFIG FspsConfig; /** Offset 0x1060 **/ UINT8 UnusedUpdSpace48[6]; /** Offset 0x1066 **/ UINT16 UpdTerminator; } FSPS_UPD; #pragma pack() #endif