/** @file
Copyright (c) 2019, Intel Corporation. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This file is automatically generated. Please do NOT modify !!!
**/
#ifndef __FSPSUPD_H__
#define __FSPSUPD_H__
#include
#pragma pack(1)
///
/// Azalia Header structure
///
typedef struct {
UINT16 VendorId; ///< Codec Vendor ID
UINT16 DeviceId; ///< Codec Device ID
UINT8 RevisionId; ///< Revision ID of the codec. 0xFF matches any revision.
UINT8 SdiNum; ///< SDI number, 0xFF matches any SDI.
UINT16 DataDwords; ///< Number of data DWORDs pointed by the codec data buffer.
UINT32 Reserved; ///< Reserved for future use. Must be set to 0.
} AZALIA_HEADER;
///
/// Audio Azalia Verb Table structure
///
typedef struct {
AZALIA_HEADER Header; ///< AZALIA PCH header
UINT32 *Data; ///< Pointer to the data buffer. Its length is specified in the header
} AUDIO_AZALIA_VERB_TABLE;
///
/// Refer to the definition of PCH_INT_PIN
///
typedef enum {
SiPchNoInt, ///< No Interrupt Pin
SiPchIntA,
SiPchIntB,
SiPchIntC,
SiPchIntD
} SI_PCH_INT_PIN;
///
/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device.
///
typedef struct {
UINT8 Device; ///< Device number
UINT8 Function; ///< Device function
UINT8 IntX; ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN)
UINT8 Irq; ///< IRQ to be set for device.
} SI_PCH_DEVICE_INTERRUPT_CONFIG;
#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG 64 ///< Number of all PCH devices
/** Fsp S Configuration
**/
typedef struct {
/** Offset 0x0020 - Logo Pointer
Points to PEI Display Logo Image
**/
UINT32 LogoPtr;
/** Offset 0x0024 - Logo Size
Size of PEI Display Logo Image
**/
UINT32 LogoSize;
/** Offset 0x0028 - Graphics Configuration Ptr
Points to VBT
**/
UINT32 GraphicsConfigPtr;
/** Offset 0x002C - Enable Device 4
Enable/disable Device 4
$EN_DIS
**/
UINT8 Device4Enable;
/** Offset 0x002D
**/
UINT8 UnusedUpdSpace0[3];
/** Offset 0x0030 - MicrocodeRegionBase
Memory Base of Microcode Updates
**/
UINT32 MicrocodeRegionBase;
/** Offset 0x0034 - MicrocodeRegionSize
Size of Microcode Updates
**/
UINT32 MicrocodeRegionSize;
/** Offset 0x0038 - Turbo Mode
Enable/Disable Turbo mode. 0: disable, 1: enable
$EN_DIS
**/
UINT8 TurboMode;
/** Offset 0x0039 - PchDmiCwbEnable
Central Write Buffer feature configurable and disabled by default
$EN_DIS
**/
UINT8 PchDmiCwbEnable;
/** Offset 0x003A - HECI3 state
The HECI3 state from Mbp for reference in S3 path or when MbpHob is not installed.
0: disable, 1: enable
$EN_DIS
**/
UINT8 Heci3Enabled;
/** Offset 0x003B - AMT Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality.
$EN_DIS
**/
UINT8 AmtEnabled;
/** Offset 0x003C - WatchDog Timer Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer. Setting
is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 WatchDogEnabled;
/** Offset 0x003D - Manageability Mode set by Mebx
Enable/Disable. 0: Disable, 1: enable, Enable or disable Manageability Mode.
$EN_DIS
**/
UINT8 ManageabilityMode;
/** Offset 0x003E - PET Progress
Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive
PET Events. Setting is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 FwProgress;
/** Offset 0x003F - SOL Switch
Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx.
Setting is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 AmtSolEnabled;
/** Offset 0x0040 - OS Timer
16 bits Value, Set OS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
UINT16 WatchDogTimerOs;
/** Offset 0x0042 - BIOS Timer
16 bits Value, Set BIOS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
UINT16 WatchDogTimerBios;
/** Offset 0x0044 - Remote Assistance Trigger Availablilty
Enable/Disable. 0: Disable, 1: enable, Remote Assistance enable/disable state by Mebx.
$EN_DIS
**/
UINT8 RemoteAssistance;
/** Offset 0x0045 - KVM Switch
Enable/Disable. 0: Disable, 1: enable, KVM enable/disable state by Mebx. Setting
is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 AmtKvmEnabled;
/** Offset 0x0046 - MEBX execution
Enable/Disable. 0: Disable, 1: enable, Force MEBX execution.
$EN_DIS
**/
UINT8 ForcMebxSyncUp;
/** Offset 0x0047 - Enable/Disable SA CRID
Enable: SA CRID, Disable (Default): SA CRID
$EN_DIS
**/
UINT8 CridEnable;
/** Offset 0x0048 - DMI ASPM
0=Disable, 1:L0s, 2:L1, 3(Default)=L0sL1
0:Disable, 1:L0s, 2:L1, 3:L0sL1
**/
UINT8 DmiAspm;
/** Offset 0x0049 - PCIe DeEmphasis control per root port
0: -6dB, 1(Default): -3.5dB
0:-6dB, 1:-3.5dB
**/
UINT8 PegDeEmphasis[4];
/** Offset 0x004D - PCIe Slot Power Limit value per root port
Slot power limit value per root port
**/
UINT8 PegSlotPowerLimitValue[4];
/** Offset 0x0051 - PCIe Slot Power Limit scale per root port
Slot power limit scale per root port
0:1.0x, 1:0.1x, 2:0.01x, 3:0x001x
**/
UINT8 PegSlotPowerLimitScale[4];
/** Offset 0x0055
**/
UINT8 UnusedUpdSpace1[1];
/** Offset 0x0056 - PCIe Physical Slot Number per root port
Physical Slot Number per root port
**/
UINT16 PegPhysicalSlotNumber[4];
/** Offset 0x005E - Enable/Disable PavpEnable
Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable
$EN_DIS
**/
UINT8 PavpEnable;
/** Offset 0x005F - CdClock Frequency selection
0=337.5 Mhz, 1=450 Mhz, 2=540 Mhz, 3(Default)=675 Mhz
0: 337.5 Mhz, 1: 450 Mhz, 2: 540 Mhz, 3: 675 Mhz
**/
UINT8 CdClock;
/** Offset 0x0060 - Enable/Disable PeiGraphicsPeimInit
Enable: Enable PeiGraphicsPeimInit, Disable(Default): Disable PeiGraphicsPeimInit
$EN_DIS
**/
UINT8 PeiGraphicsPeimInit;
/** Offset 0x0061 - Enable or disable GNA device
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 GnaEnable;
/** Offset 0x0062 - State of X2APIC_OPT_OUT bit in the DMAR table
0=Disable/Clear, 1=Enable/Set
$EN_DIS
**/
UINT8 X2ApicOptOutDeprecated;
/** Offset 0x0063
**/
UINT8 UnusedUpdSpace2[1];
/** Offset 0x0064 - Base addresses for VT-d function MMIO access
Base addresses for VT-d MMIO access per VT-d engine
**/
UINT32 VtdBaseAddressDeprecated[3];
/** Offset 0x0070 - Enable or disable eDP device
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortEdp;
/** Offset 0x0071 - Enable or disable HPD of DDI port B
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortBHpd;
/** Offset 0x0072 - Enable or disable HPD of DDI port C
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortCHpd;
/** Offset 0x0073 - Enable or disable HPD of DDI port D
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortDHpd;
/** Offset 0x0074 - Enable or disable HPD of DDI port F
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortFHpd;
/** Offset 0x0075 - Enable or disable DDC of DDI port B
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortBDdc;
/** Offset 0x0076 - Enable or disable DDC of DDI port C
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortCDdc;
/** Offset 0x0077 - Enable or disable DDC of DDI port D
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortDDdc;
/** Offset 0x0078 - Enable or disable DDC of DDI port F
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPortFDdc;
/** Offset 0x0079 - Enable/Disable SkipS3CdClockInit
Enable: Skip Full CD clock initializaton, Disable(Default): Initialize the full
CD clock in S3 resume due to GOP absent
$EN_DIS
**/
UINT8 SkipS3CdClockInit;
/** Offset 0x007A - Delta T12 Power Cycle Delay required in ms
DEPRECATED
0 : No Delay, 0xFFFF : Auto Calulate T12 Delay
**/
UINT16 DeltaT12PowerCycleDelay;
/** Offset 0x007C - Blt Buffer Address
Address of Blt buffer
**/
UINT32 BltBufferAddress;
/** Offset 0x0080 - Blt Buffer Size
Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of
EFI_GRAPHICS_OUTPUT_BLT_PIXEL)
**/
UINT32 BltBufferSize;
/** Offset 0x0084 - SaPostMemProductionRsvd
Reserved for SA Post-Mem Production
$EN_DIS
**/
UINT8 SaPostMemProductionRsvd[35];
/** Offset 0x00A7 - PCIE RP Disable Gen2PLL Shutdown and L1 Clock Gating Enable
PCIE RP Disable Gen2PLL Shutdown and L1 Clock Gating Enable Workaround needed for
Alpine ridge
**/
UINT8 PcieRootPortGen2PllL1CgDisable[24];
/** Offset 0x00BF - Advanced Encryption Standard (AES) feature
Enable or Disable Advanced Encryption Standard (AES) feature; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 AesEnable;
/** Offset 0x00C0 - Power State 3 enable/disable
PCODE MMIO Mailbox: Power State 3 enable/disable; 0: Disable; 1: Enable.
For all VR Indexes
**/
UINT8 Psi3Enable[5];
/** Offset 0x00C5 - Power State 4 enable/disable
PCODE MMIO Mailbox: Power State 4 enable/disable; 0: Disable; 1: Enable.For
all VR Indexes
**/
UINT8 Psi4Enable[5];
/** Offset 0x00CA - Imon slope correction
PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values.
Range is 0-200. 125 = 1.25. 0: Auto.For all VR Indexes
**/
UINT8 ImonSlope[5];
/** Offset 0x00CF - Imon offset correction
DEPRECATED
**/
UINT8 ImonOffset[5];
/** Offset 0x00D4 - Enable/Disable BIOS configuration of VR
Enable/Disable BIOS configuration of VR; 0: Disable; 1: Enable.For all VR Indexes
**/
UINT8 VrConfigEnable[5];
/** Offset 0x00D9 - Thermal Design Current enable/disable
PCODE MMIO Mailbox: Thermal Design Current enable/disable; 0: Disable; 1:
Enable.For all VR Indexes
**/
UINT8 TdcEnable[5];
/** Offset 0x00DE - HECI3 state
PCODE MMIO Mailbox: Thermal Design Current time window. Defined in milli seconds.
Valid Values 1 - 1ms , 2 - 2ms , 3 - 3ms , 4 - 4ms , 5 - 5ms , 6 - 6ms , 7 - 7ms
, 8 - 8ms , 10 - 10ms.For all VR Indexe
**/
UINT8 TdcTimeWindow[5];
/** Offset 0x00E3 - Thermal Design Current Lock
PCODE MMIO Mailbox: Thermal Design Current Lock; 0: Disable; 1: Enable.For
all VR Indexes
**/
UINT8 TdcLock[5];
/** Offset 0x00E8 - Platform Psys slope correction
PCODE MMIO Mailbox: Platform Psys slope correction. 0 - Auto Specified in
1/100 increment values. Range is 0-200. 125 = 1.25
**/
UINT8 PsysSlope;
/** Offset 0x00E9 - Platform Psys offset correction
PCODE MMIO Mailbox: Platform Psys offset correction. 0 - Auto Units 1/4,
Range 0-255. Value of 100 = 100/4 = 25 offset
**/
UINT8 PsysOffset;
/** Offset 0x00EA - Acoustic Noise Mitigation feature
Enable or Disable Acoustic Noise Mitigation feature. This has to be enabled to program
slew rate configuration for all VR domains, Pre Wake, Ramp Up and, Ramp Down times.0:
Disabled; 1: Enabled
$EN_DIS
**/
UINT8 AcousticNoiseMitigation;
/** Offset 0x00EB - Disable Fast Slew Rate for Deep Package C States for VR IA domain
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. 0: False; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisableIa;
/** Offset 0x00EC - Slew Rate configuration for Deep Package C States for VR IA domain
Slew Rate configuration for Deep Package C States for VR IA domain based on Acoustic
Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRateForIa;
/** Offset 0x00ED - Slew Rate configuration for Deep Package C States for VR GT domain
Slew Rate configuration for Deep Package C States for VR GT domain based on Acoustic
Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRateForGt;
/** Offset 0x00EE - Slew Rate configuration for Deep Package C States for VR SA domain
Slew Rate configuration for Deep Package C States for VR SA domain based on Acoustic
Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRateForSa;
/** Offset 0x00EF
**/
UINT8 UnusedUpdSpace3[1];
/** Offset 0x00F0 - Thermal Design Current current limit
PCODE MMIO Mailbox: Thermal Design Current current limit. Specified in 1/8A units.
Range is 0-4095. 1000 = 125A. 0: Auto. For all VR Indexes
**/
UINT16 TdcPowerLimit[5];
/** Offset 0x00FA - AcLoadline
PCODE MMIO Mailbox: AcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
0-6249. Intel Recommended Defaults vary by domain and SKU.
**/
UINT16 AcLoadline[5];
/** Offset 0x0104 - DcLoadline
PCODE MMIO Mailbox: DcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
0-6249.Intel Recommended Defaults vary by domain and SKU.
**/
UINT16 DcLoadline[5];
/** Offset 0x010E - Power State 1 Threshold current
PCODE MMIO Mailbox: Power State 1 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi1Threshold[5];
/** Offset 0x0118 - Power State 2 Threshold current
PCODE MMIO Mailbox: Power State 2 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi2Threshold[5];
/** Offset 0x0122 - Power State 3 Threshold current
PCODE MMIO Mailbox: Power State 3 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi3Threshold[5];
/** Offset 0x012C - Icc Max limit
PCODE MMIO Mailbox: VR Icc Max limit. 0-255A in 1/4 A units. 400 = 100A
**/
UINT16 IccMax[5];
/** Offset 0x0136 - VR Voltage Limit
PCODE MMIO Mailbox: VR Voltage Limit. Range is 0-7999mV.
**/
UINT16 VrVoltageLimit[5];
/** Offset 0x0140 - Disable Fast Slew Rate for Deep Package C States for VR GT domain
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. 0: False; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisableGt;
/** Offset 0x0141 - Disable Fast Slew Rate for Deep Package C States for VR SA domain
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. 0: False; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisableSa;
/** Offset 0x0142 - Enable VR specific mailbox command
VR specific mailbox commands. 00b - no VR specific command sent. 01b - A
VR mailbox command specifically for the MPS IMPV8 VR will be sent. 10b - VR specific
command sent for PS4 exit issue. 11b - Reserved.
$EN_DIS
**/
UINT8 SendVrMbxCmd;
/** Offset 0x0143 - Reserved
Reserved
**/
UINT8 Reserved2;
/** Offset 0x0144 - Enable or Disable TXT
Enable or Disable TXT; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 TxtEnable;
/** Offset 0x0145 - Deprecated DO NOT USE Skip Multi-Processor Initialization
@deprecated SkipMpInit has been moved to FspmUpd
$EN_DIS
**/
UINT8 SkipMpInitDeprecated;
/** Offset 0x0146 - McIVR RFI Frequency Prefix
PCODE MMIO Mailbox: McIVR RFI Frequency Adjustment Prefix. 0: Plus (+); 1:
Minus (-).
**/
UINT8 McivrRfiFrequencyPrefix;
/** Offset 0x0147 - McIVR RFI Frequency Adjustment
PCODE MMIO Mailbox: Adjust the RFI frequency relative to the nominal frequency in
increments of 100KHz. For subtraction, change McivrRfiFrequencyPrefix. 0: Auto.
**/
UINT8 McivrRfiFrequencyAdjust;
/** Offset 0x0148 - FIVR RFI Frequency
PCODE MMIO Mailbox: Set the desired RFI frequency, in increments of 100KHz. 0:
Auto. Range varies based on XTAL clock: 0-1918 (Up to 191.8HMz) for 24MHz clock;
0-1535 (Up to 153.5MHz) for 19MHz clock.
**/
UINT16 FivrRfiFrequency;
/** Offset 0x014A - McIVR RFI Spread Spectrum
PCODE MMIO Mailbox: McIVR RFI Spread Spectrum. 0: 0%; 1: +/- 0.5%; 2: +/-
1%; 3: +/- 1.5%; 4: +/- 2%; 5: +/- 3%; 6: +/- 4%; 7: +/- 5%; 8: +/- 6%.
**/
UINT8 McivrSpreadSpectrum;
/** Offset 0x014B - FIVR RFI Spread Spectrum
PCODE MMIO Mailbox: FIVR RFI Spread Spectrum, in 0.1% increments. 0: 0%;
Range: 0.0% to 10.0% (0-100).
**/
UINT8 FivrSpreadSpectrum;
/** Offset 0x014C - Disable Fast Slew Rate for Deep Package C States for VR FIVR domain
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. 0: False; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisableFivr;
/** Offset 0x014D - Slew Rate configuration for Deep Package C States for VR FIVR domain
Slew Rate configuration for Deep Package C States for VR FIVR domain based on Acoustic
Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRateForFivr;
/** Offset 0x014E
**/
UINT8 UnusedUpdSpace4[2];
/** Offset 0x0150 - CpuBistData
Pointer CPU BIST Data
**/
UINT32 CpuBistData;
/** Offset 0x0154 - Activates VR mailbox command for Intersil VR C-state issues.
Intersil VR mailbox command. 0 - no mailbox command sent. 1 - VR mailbox
command sent for IA/GT rails only. 2 - VR mailbox command sent for IA/GT/SA rails.
**/
UINT8 IslVrCmd;
/** Offset 0x0155
**/
UINT8 UnusedUpdSpace5[1];
/** Offset 0x0156 - Imon slope1 correction
PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values.
Range is 0-200. 125 = 1.25. 0: Auto.For all VR Indexes
**/
UINT16 ImonSlope1[5];
/** Offset 0x0160 - CPU VR Power Delivery Design
Used to communicate the power delivery design capability of the board. This value
is an enum of the available power delivery segments that are defined in the Platform
Design Guide.
**/
UINT32 VrPowerDeliveryDesign;
/** Offset 0x0164 - Pre Wake Randomization time
PCODE MMIO Mailbox: Acoustic Migitation Range.Defines the maximum pre-wake randomization
time in micro ticks.This can be programmed only if AcousticNoiseMigitation is enabled.
Range 0-255 0.
**/
UINT8 PreWake;
/** Offset 0x0165 - Ramp Up Randomization time
PCODE MMIO Mailbox: Acoustic Migitation Range.Defines the maximum Ramp Up randomization
time in micro ticks.This can be programmed only if AcousticNoiseMigitation is enabled.Range
0-255 0.
**/
UINT8 RampUp;
/** Offset 0x0166 - Ramp Down Randomization time
PCODE MMIO Mailbox: Acoustic Migitation Range.Defines the maximum Ramp Down randomization
time in micro ticks.This can be programmed only if AcousticNoiseMigitation is enabled.Range
0-255 0.
**/
UINT8 RampDown;
/** Offset 0x0167
**/
UINT8 UnusedUpdSpace6;
/** Offset 0x0168 - CpuMpPpi
Pointer for CpuMpPpi
**/
UINT32 CpuMpPpi;
/** Offset 0x016C - CpuMpHob
Pointer for CpuMpHob. This is optional data buffer for CpuMpPpi usage.
**/
UINT32 CpuMpHob;
/** Offset 0x0170 - Enable or Disable processor debug features
Enable or Disable processor debug features; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DebugInterfaceEnable;
/** Offset 0x0171
**/
UINT8 UnusedUpdSpace7[1];
/** Offset 0x0172 - Imon offset 1 correction
PCODE MMIO Mailbox: Imon offset correction. Value is a 2's complement signed integer.
Units 1/1000, Range 0-63999. For an offset = 12.580, use 12580. 0: Auto
**/
UINT16 ImonOffset1[5];
/** Offset 0x017C - ReservedCpuPostMemProduction
Reserved for CPU Post-Mem Production
$EN_DIS
**/
UINT8 ReservedCpuPostMemProduction[8];
/** Offset 0x0184 - Enable Intel HD Audio (Azalia)
Enable/disable Azalia controller.
$EN_DIS
**/
UINT8 PchHdaEnable;
/** Offset 0x0185 - Enable HD Audio DSP
Enable/disable HD Audio DSP feature.
$EN_DIS
**/
UINT8 PchHdaDspEnable;
/** Offset 0x0186 - Select HDAudio IoBuffer Ownership
Indicates the ownership of the I/O buffer between Intel HD Audio link vs I2S0 /
I2S port. 0: Intel HD-Audio link owns all the I/O buffers. 1: Intel HD-Audio link
owns 4 of the I/O buffers for 1 HD-Audio codec connection, and I2S1 port owns 4
of the I/O buffers for 1 I2S codec connection. 2: Reserved. 3: I2S0 and I2S1 ports
own all the I/O buffers.
0:HD-A Link, 1:Shared HD-A Link and I2S Port, 3:I2S Ports
**/
UINT8 PchHdaIoBufferOwnership;
/** Offset 0x0187 - Configure CLKSRC Number
Configure Root Port CLKSRC Number. Each value in arrary can be between 0-6 for valid
clock numbers or 0x1F for an invalid number. One byte for each port, byte0 for
port1, byte1 for port2, and so on.
**/
UINT8 PcieRpClkSrcNumber[24];
/** Offset 0x019F - Force Disable clock
Disables clock even if link is inactive default value is 0
**/
UINT8 PcieRpForceClkDisableWhenRpDisable[24];
/** Offset 0x01B7 - Enable CIO2 Controller
Enable/disable SKYCAM CIO2 Controller.
$EN_DIS
**/
UINT8 PchCio2Enable;
/** Offset 0x01B8 - SPI0 Chip Select Polarity
Sets polarity for each chip Select. Available options: 0:PchSerialIoCsActiveLow,
1:PchSerialIoCsActiveHigh
**/
UINT8 SerialIoSpi0CsPolarity[2];
/** Offset 0x01BA - SPI1 Chip Select Polarity
Sets polarity for each chip Select. Available options: 0:PchSerialIoCsActiveLow,
1:PchSerialIoCsActiveHigh
**/
UINT8 SerialIoSpi1CsPolarity[2];
/** Offset 0x01BC - SPI0 Chip Select Enable
0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled
**/
UINT8 SerialIoSpi0CsEnable[2];
/** Offset 0x01BE - SPI1 Chip Select Enable
0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled
**/
UINT8 SerialIoSpi1CsEnable[2];
/** Offset 0x01C0 - SPIn Device Mode
Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available
modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden
**/
UINT8 SerialIoSpiMode[2];
/** Offset 0x01C2 - SPIn Default Chip Select Output
Sets Default CS as Output. N represents controller index: SPI0, SPI1, ... Available
options: 0:CS0, 1:CS1
**/
UINT8 SerialIoSpiDefaultCsOutput[2];
/** Offset 0x01C4 - PCH SerialIo I2C Pads Termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,I2C2,I2C3,I2C4,I2C5
pads termination respectively. One byte for each controller, byte0 for I2C0, byte1
for I2C1, and so on.
**/
UINT8 PchSerialIoI2cPadsTermination[6];
/** Offset 0x01CA - I2Cn Device Mode
Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available
modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden
**/
UINT8 SerialIoI2cMode[6];
/** Offset 0x01D0 - UARTn Device Mode
Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available
modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
4:SerialIoUartSkipInit
**/
UINT8 SerialIoUartMode[3];
/** Offset 0x01D3
**/
UINT8 UnusedUpdSpace8[1];
/** Offset 0x01D4 - Default BaudRate for each Serial IO UART
Set default BaudRate Supported from 0 - default to 6000000
**/
UINT32 SerialIoUartBaudRate[3];
/** Offset 0x01E0 - Default ParityType for each Serial IO UART
Set default Parity. 0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
**/
UINT8 SerialIoUartParity[3];
/** Offset 0x01E3 - Default DataBits for each Serial IO UART
Set default word length. 0: Default, 5,6,7,8
**/
UINT8 SerialIoUartDataBits[3];
/** Offset 0x01E6 - Default StopBits for each Serial IO UART
Set default stop bits. 0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3:
TwoStopBits
**/
UINT8 SerialIoUartStopBits[3];
/** Offset 0x01E9 - Power Gating mode for each Serial IO UART that works in COM mode
Set Power Gating. 0: Disabled, 1: Enabled, 2: Auto
**/
UINT8 SerialIoUartPowerGating[3];
/** Offset 0x01EC - Enable Dma for each Serial IO UART that supports it
Set DMA/PIO mode. 0: Disabled, 1: Enabled
**/
UINT8 SerialIoUartDmaEnable[3];
/** Offset 0x01EF - Enables UART hardware flow control, CTS and RTS lines
Enables UART hardware flow control, CTS and RTS lines.
**/
UINT8 SerialIoUartAutoFlow[3];
/** Offset 0x01F2
**/
UINT8 UnusedUpdSpace9[2];
/** Offset 0x01F4 - SerialIoUartRxPinMux
Select SerialIo Uart Rx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RX* for
possible values.
**/
UINT32 SerialIoUartRxPinMux[3];
/** Offset 0x0200 - SerialIoUartTxPinMux
Select SerialIo Uart Tx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_TX* for
possible values.
**/
UINT32 SerialIoUartTxPinMux[3];
/** Offset 0x020C - SerialIoUartRtsPinMux
Select SerialIo Uart Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
for possible values.
**/
UINT32 SerialIoUartRtsPinMux[3];
/** Offset 0x0218 - SerialIoUartCtsPinMux
Select SerialIo Uart Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
for possible values.
**/
UINT32 SerialIoUartCtsPinMux[3];
/** Offset 0x0224 - UART Number For Debug Purpose
UART number for debug purpose. 0:UART0, 1: UART1, 2:UART2. Note: If UART0 is selected
as CNVi BT Core interface, it cannot be used for debug purpose.
0:UART0, 1:UART1, 2:UART2
**/
UINT8 SerialIoDebugUartNumber;
/** Offset 0x0225 - Enable eMMC Controller
Enable/disable eMMC Controller.
$EN_DIS
**/
UINT8 ScsEmmcEnabled;
/** Offset 0x0226 - Enable eMMC HS400 Mode
Enable eMMC HS400 Mode.
$EN_DIS
**/
UINT8 ScsEmmcHs400Enabled;
/** Offset 0x0227 - Enable SdCard Controller
Enable/disable SD Card Controller.
$EN_DIS
**/
UINT8 ScsSdCardEnabled;
/** Offset 0x0228 - Enable PCH ISH Controller
Enable/disable ISH Controller.
$EN_DIS
**/
UINT8 PchIshEnable;
/** Offset 0x0229 - Show SPI controller
Enable/disable to show SPI controller.
$EN_DIS
**/
UINT8 ShowSpiController;
/** Offset 0x022A - Flash Configuration Lock Down
Enable/disable flash lock down. If platform decides to skip this programming, it
must lock SPI flash register DLOCK, FLOCKDN, and WRSDIS before end of post.
$EN_DIS
**/
UINT8 SpiFlashCfgLockDown;
/** Offset 0x022B - Enable SATA SALP Support
Enable/disable SATA Aggressive Link Power Management.
$EN_DIS
**/
UINT8 SataSalpSupport;
/** Offset 0x022C - Enable SATA ports
Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1,
and so on.
**/
UINT8 SataPortsEnable[8];
/** Offset 0x0234 - Enable SATA DEVSLP Feature
Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each
port, byte0 for port0, byte1 for port1, and so on.
**/
UINT8 SataPortsDevSlp[8];
/** Offset 0x023C - Enable USB2 ports
Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for
port1, and so on.
**/
UINT8 PortUsb20Enable[16];
/** Offset 0x024C - Enable USB3 ports
Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for
port1, and so on.
**/
UINT8 PortUsb30Enable[10];
/** Offset 0x0256 - Enable xDCI controller
Enable/disable to xDCI controller.
$EN_DIS
**/
UINT8 XdciEnable;
/** Offset 0x0257 - Enable XHCI SSIC Enable
Enable/disable XHCI SSIC port.
$EN_DIS
**/
UINT8 SsicPortEnable;
/** Offset 0x0258 - Number of DevIntConfig Entry
Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr
must not be NULL.
**/
UINT8 NumOfDevIntConfig;
/** Offset 0x0259
**/
UINT8 UnusedUpdSpace10[3];
/** Offset 0x025C - Address of PCH_DEVICE_INTERRUPT_CONFIG table.
The address of the table of PCH_DEVICE_INTERRUPT_CONFIG.
**/
UINT32 DevIntConfigPtr;
/** Offset 0x0260 - PIRQx to IRQx Map Config
PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for
PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy
8259 PCI mode.
**/
UINT8 PxRcConfig[8];
/** Offset 0x0268 - Select GPIO IRQ Route
GPIO IRQ Select. The valid value is 14 or 15.
**/
UINT8 GpioIrqRoute;
/** Offset 0x0269 - Select SciIrqSelect
SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only.
**/
UINT8 SciIrqSelect;
/** Offset 0x026A - Select TcoIrqSelect
TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23.
**/
UINT8 TcoIrqSelect;
/** Offset 0x026B - Enable/Disable Tco IRQ
Enable/disable TCO IRQ
$EN_DIS
**/
UINT8 TcoIrqEnable;
/** Offset 0x026C - PCH HDA Verb Table Entry Number
Number of Entries in Verb Table.
**/
UINT8 PchHdaVerbTableEntryNum;
/** Offset 0x026D
**/
UINT8 UnusedUpdSpace11[3];
/** Offset 0x0270 - PCH HDA Verb Table Pointer
Pointer to Array of pointers to Verb Table.
**/
UINT32 PchHdaVerbTablePtr;
/** Offset 0x0274 - Enable SATA
Enable/disable SATA controller.
$EN_DIS
**/
UINT8 SataEnable;
/** Offset 0x0275 - SATA Mode
Select SATA controller working mode.
0:AHCI, 1:RAID
**/
UINT8 SataMode;
/** Offset 0x0276 - USB Per Port HS Preemphasis Bias
USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port.
**/
UINT8 Usb2AfePetxiset[16];
/** Offset 0x0286 - USB Per Port HS Transmitter Bias
USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port.
**/
UINT8 Usb2AfeTxiset[16];
/** Offset 0x0296 - USB Per Port HS Transmitter Emphasis
USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON,
10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port.
**/
UINT8 Usb2AfePredeemp[16];
/** Offset 0x02A6 - USB Per Port Half Bit Pre-emphasis
USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis.
One byte for each port.
**/
UINT8 Usb2AfePehalfbit[16];
/** Offset 0x02B6 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment
Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value
in arrary can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxDeEmphEnable[10];
/** Offset 0x02C0 - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting
USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16],
Default = 29h (approximately -3.5dB De-Emphasis). One byte for each port.
**/
UINT8 Usb3HsioTxDeEmph[10];
/** Offset 0x02CA - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment
Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value
in arrary can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxDownscaleAmpEnable[10];
/** Offset 0x02D4 - USB 3.0 TX Output Downscale Amplitude Adjustment
USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], Default
= 00h. One byte for each port.
**/
UINT8 Usb3HsioTxDownscaleAmp[10];
/** Offset 0x02DE - Enable LAN
Enable/disable LAN controller.
$EN_DIS
**/
UINT8 PchLanEnable;
/** Offset 0x02DF - Delay USB PDO Programming
Enable/disable delay of PDO programming for USB from PEI phase to DXE phase. 0:
disable, 1: enable
$EN_DIS
**/
UINT8 DelayUsbPdoProgramming;
/** Offset 0x02E0 - Trace Hub Memory Base
If Trace Hub is enabled and trace to memory is desired, BootLoader needs to allocate
trace hub memory as reserved and uncacheable, set the base to ensure Trace Hub
memory is configured properly.
**/
UINT32 TraceHubMemBase;
/** Offset 0x02E4 - Enable PCIE RP CLKREQ Support
Enable/disable PCIE Root Port CLKREQ support. 0: disable, 1: enable. One byte for
each port, byte0 for port1, byte1 for port2, and so on.
**/
UINT8 PcieRpClkReqSupport[24];
/** Offset 0x02FC - Configure CLKREQ Number
Configure Root Port CLKREQ Number if CLKREQ is supported. Each value in arrary can
be between 0-6. One byte for each port, byte0 for port1, byte1 for port2, and so on.
**/
UINT8 PcieRpClkReqNumber[24];
/** Offset 0x0314 - Enable CPU PCIE RP CLKREQ Support
Enable/disable CPU PCIE Root Port CLKREQ support. 0: disable, 1: enable. One byte
for each port, byte0 for port1, byte1 for port2, and so on.
**/
UINT8 CpuPcieRpClkReqSupport[4];
/** Offset 0x0318 - Configure CPU PCIE CLKREQ Number
Configure CPU Root Port CLKREQ Number if CLKREQ is supported. Each value in arrary
can be between 0-3. One byte for each port, byte0 for port1, byte1 for port2, and so on.
**/
UINT8 CpuPcieRpClkReqNumber[4];
/** Offset 0x031C - Enable SkyCam PortA Termination override
Enable/disable PortA Termination override.
$EN_DIS
**/
UINT8 PchSkyCamPortATermOvrEnable;
/** Offset 0x031D - Enable SkyCam PortB Termination override
Enable/disable PortB Termination override.
$EN_DIS
**/
UINT8 PchSkyCamPortBTermOvrEnable;
/** Offset 0x031E - Enable SkyCam PortC Termination override
Enable/disable PortC Termination override.
$EN_DIS
**/
UINT8 PchSkyCamPortCTermOvrEnable;
/** Offset 0x031F - Enable SkyCam PortD Termination override
Enable/disable PortD Termination override.
$EN_DIS
**/
UINT8 PchSkyCamPortDTermOvrEnable;
/** Offset 0x0320 - Enable SkyCam PortA Clk Trim
Enable/disable PortA Clk Trim.
$EN_DIS
**/
UINT8 PchSkyCamPortATrimEnable;
/** Offset 0x0321 - Enable SkyCam PortB Clk Trim
Enable/disable PortB Clk Trim.
$EN_DIS
**/
UINT8 PchSkyCamPortBTrimEnable;
/** Offset 0x0322 - Enable SkyCam PortC Clk Trim
Enable/disable PortC Clk Trim.
$EN_DIS
**/
UINT8 PchSkyCamPortCTrimEnable;
/** Offset 0x0323 - Enable SkyCam PortD Clk Trim
Enable/disable PortD Clk Trim.
$EN_DIS
**/
UINT8 PchSkyCamPortDTrimEnable;
/** Offset 0x0324 - Enable SkyCam PortA Ctle
Enable/disable PortA Ctle.
$EN_DIS
**/
UINT8 PchSkyCamPortACtleEnable;
/** Offset 0x0325 - Enable SkyCam PortB Ctle
Enable/disable PortB Ctle.
$EN_DIS
**/
UINT8 PchSkyCamPortBCtleEnable;
/** Offset 0x0326 - Enable SkyCam PortCD Ctle
Enable/disable PortCD Ctle.
$EN_DIS
**/
UINT8 PchSkyCamPortCDCtleEnable;
/** Offset 0x0327 - Enable SkyCam PortA Ctle Cap Value
Enable/disable PortA Ctle Cap Value.
**/
UINT8 PchSkyCamPortACtleCapValue;
/** Offset 0x0328 - Enable SkyCam PortB Ctle Cap Value
Enable/disable PortB Ctle Cap Value.
**/
UINT8 PchSkyCamPortBCtleCapValue;
/** Offset 0x0329 - Enable SkyCam PortCD Ctle Cap Value
Enable/disable PortCD Ctle Cap Value.
**/
UINT8 PchSkyCamPortCDCtleCapValue;
/** Offset 0x032A - Enable SkyCam PortA Ctle Res Value
Enable/disable PortA Ctle Res Value.
**/
UINT8 PchSkyCamPortACtleResValue;
/** Offset 0x032B - Enable SkyCam PortB Ctle Res Value
Enable/disable PortB Ctle Res Value.
**/
UINT8 PchSkyCamPortBCtleResValue;
/** Offset 0x032C - Enable SkyCam PortCD Ctle Res Value
Enable/disable PortCD Ctle Res Value.
**/
UINT8 PchSkyCamPortCDCtleResValue;
/** Offset 0x032D - Enable SkyCam PortA Clk Trim Value
Enable/disable PortA Clk Trim Value.
**/
UINT8 PchSkyCamPortAClkTrimValue;
/** Offset 0x032E - Enable SkyCam PortB Clk Trim Value
Enable/disable PortB Clk Trim Value.
**/
UINT8 PchSkyCamPortBClkTrimValue;
/** Offset 0x032F - Enable SkyCam PortC Clk Trim Value
Enable/disable PortC Clk Trim Value.
**/
UINT8 PchSkyCamPortCClkTrimValue;
/** Offset 0x0330 - Enable SkyCam PortD Clk Trim Value
Enable/disable PortD Clk Trim Value.
**/
UINT8 PchSkyCamPortDClkTrimValue;
/** Offset 0x0331
**/
UINT8 UnusedUpdSpace12;
/** Offset 0x0332 - Enable SkyCam Port A Data Trim Value
Enable/disable Port A Data Trim Value.
**/
UINT16 PchSkyCamPortADataTrimValue;
/** Offset 0x0334 - Enable SkyCam Port B Data Trim Value
Enable/disable Port B Data Trim Value.
**/
UINT16 PchSkyCamPortBDataTrimValue;
/** Offset 0x0336 - Enable SkyCam C/D Data Trim Value
Enable/disable C/D Data Trim Value.
**/
UINT16 PchSkyCamPortCDDataTrimValue;
/** Offset 0x0338 - Enable DMI ASPM
ASPM on PCH side of the DMI Link.
$EN_DIS
**/
UINT8 PchDmiAspm;
/** Offset 0x0339 - Enable Power Optimizer
Enable DMI Power Optimizer on PCH side.
$EN_DIS
**/
UINT8 PchPwrOptEnable;
/** Offset 0x033A - PCH Flash Protection Ranges Write Enble
Write or erase is blocked by hardware.
**/
UINT8 PchWriteProtectionEnable[5];
/** Offset 0x033F - PCH Flash Protection Ranges Read Enble
Read is blocked by hardware.
**/
UINT8 PchReadProtectionEnable[5];
/** Offset 0x0344 - PCH Protect Range Limit
Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for
limit comparison.
**/
UINT16 PchProtectedRangeLimit[5];
/** Offset 0x034E - PCH Protect Range Base
Left shifted address by 12 bits with address bits 11:0 are assumed to be 0.
**/
UINT16 PchProtectedRangeBase[5];
/** Offset 0x0358 - Enable Pme
Enable Azalia wake-on-ring.
$EN_DIS
**/
UINT8 PchHdaPme;
/** Offset 0x0359 - IO Buffer Voltage
I/O Buffer Voltage Mode Select: 0: 3.3V, 1: 1.8V.
**/
UINT8 PchHdaIoBufferVoltage;
/** Offset 0x035A - VC Type
Virtual Channel Type Select: 0: VC0, 1: VC1.
**/
UINT8 PchHdaVcType;
/** Offset 0x035B - HD Audio Link Frequency
HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, , 1: 12MHz, 2: 24MHz.
**/
UINT8 PchHdaLinkFrequency;
/** Offset 0x035C - iDisp-Link Frequency
iDisp-Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 4: 96MHz, 3: 48MHz.
**/
UINT8 PchHdaIDispLinkFrequency;
/** Offset 0x035D - iDisp-Link T-mode
iDisp-Link T-Mode (PCH_HDAUDIO_IDISP_TMODE enum): 0: 2T, 1: 1T.
**/
UINT8 PchHdaIDispLinkTmode;
/** Offset 0x035E - Universal Audio Architecture compliance for DSP enabled system
0: Not-UAA Compliant (Intel SST driver supported only), 1: UAA Compliant (HDA Inbox
driver or SST driver supported).
$EN_DIS
**/
UINT8 PchHdaDspUaaCompliance;
/** Offset 0x035F - iDisplay Audio Codec disconnection
0: Not disconnected, enumerable, 1: Disconnected SDI, not enumerable.
$EN_DIS
**/
UINT8 PchHdaIDispCodecDisconnect;
/** Offset 0x0360 - Enable PCH Io Apic
Set to 1 if BDF value is valid.
$EN_DIS
**/
UINT8 PchIoApicBdfValid;
/** Offset 0x0361 - PCH Io Apic Bus Number
Bus/Device/Function used as Requestor / Completer ID. Default is 0xF0.
**/
UINT8 PchIoApicBusNumber;
/** Offset 0x0362 - PCH Io Apic Device Number
Bus/Device/Function used as Requestor / Completer ID. Default is 0x1F.
**/
UINT8 PchIoApicDeviceNumber;
/** Offset 0x0363 - PCH Io Apic Function Number
Bus/Device/Function used as Requestor / Completer ID. Default is 0x00.
**/
UINT8 PchIoApicFunctionNumber;
/** Offset 0x0364 - Enable PCH Io Apic Entry 24-119
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIoApicEntry24_119;
/** Offset 0x0365 - PCH Io Apic ID
This member determines IOAPIC ID. Default is 0x02.
**/
UINT8 PchIoApicId;
/** Offset 0x0366 - PCH Io Apic Range Select
Define address bits 19:12 for the IOxAPIC range. Default is 0.
**/
UINT8 PchIoApicRangeSelect;
/** Offset 0x0367 - Enable PCH ISH SPI GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshSpiGpioAssign;
/** Offset 0x0368 - Enable PCH ISH UART0 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshUart0GpioAssign;
/** Offset 0x0369 - Enable PCH ISH UART1 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshUart1GpioAssign;
/** Offset 0x036A - Enable PCH ISH I2C0 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshI2c0GpioAssign;
/** Offset 0x036B - Enable PCH ISH I2C1 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshI2c1GpioAssign;
/** Offset 0x036C - Enable PCH ISH I2C2 GPIO pins assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshI2c2GpioAssign;
/** Offset 0x036D - Enable PCH ISH GP_0 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp0GpioAssign;
/** Offset 0x036E - Enable PCH ISH GP_1 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp1GpioAssign;
/** Offset 0x036F - Enable PCH ISH GP_2 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp2GpioAssign;
/** Offset 0x0370 - Enable PCH ISH GP_3 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp3GpioAssign;
/** Offset 0x0371 - Enable PCH ISH GP_4 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp4GpioAssign;
/** Offset 0x0372 - Enable PCH ISH GP_5 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp5GpioAssign;
/** Offset 0x0373 - Enable PCH ISH GP_6 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp6GpioAssign;
/** Offset 0x0374 - Enable PCH ISH GP_7 GPIO pin assigned
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIshGp7GpioAssign;
/** Offset 0x0375 - PCH ISH PDT Unlock Msg
0: False; 1: True.
$EN_DIS
**/
UINT8 PchIshPdtUnlock;
/** Offset 0x0376 - Enable PCH Lan LTR capabilty of PCH internal LAN
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchLanLtrEnable;
/** Offset 0x0377 - Enable PCH Lan use CLKREQ for GbE power management
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchLanK1OffEnable;
/** Offset 0x0378 - Indicate whether dedicated CLKREQ# is supported
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchLanClkReqSupported;
/** Offset 0x0379 - CLKREQ# used by GbE
Valid if ClkReqSupported is TRUE.
**/
UINT8 PchLanClkReqNumber;
/** Offset 0x037A - Enable LOCKDOWN BIOS LOCK
Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region
protection.
$EN_DIS
**/
UINT8 PchLockDownBiosLock;
/** Offset 0x037B - Enable LOCKDOWN SPI Eiss
Enable InSMM.STS (EISS) in SPI.
$EN_DIS
**/
UINT8 PchLockDownSpiEiss;
/** Offset 0x037C - PCH Compatibility Revision ID
This member describes whether or not the CRID feature of PCH should be enabled.
$EN_DIS
**/
UINT8 PchCrid;
/** Offset 0x037D - PCH Legacy IO Low Latency Enable
todo
$EN_DIS
**/
UINT8 PchLegacyIoLowLatency;
/** Offset 0x037E - Enable PCIE RP HotPlug
Indicate whether the root port is hot plug available.
**/
UINT8 PcieRpHotPlug[24];
/** Offset 0x0396 - Enable PCIE RP Pm Sci
Indicate whether the root port power manager SCI is enabled.
**/
UINT8 PcieRpPmSci[24];
/** Offset 0x03AE - Enable PCIE RP Ext Sync
Indicate whether the extended synch is enabled.
**/
UINT8 PcieRpExtSync[24];
/** Offset 0x03C6 - Enable PCIE RP Transmitter Half Swing
Indicate whether the Transmitter Half Swing is enabled.
**/
UINT8 PcieRpTransmitterHalfSwing[24];
/** Offset 0x03DE - Enable PCIE RP Clk Req Detect
Probe CLKREQ# signal before enabling CLKREQ# based power management.
**/
UINT8 PcieRpClkReqDetect[24];
/** Offset 0x03F6 - PCIE RP Advanced Error Report
Indicate whether the Advanced Error Reporting is enabled.
**/
UINT8 PcieRpAdvancedErrorReporting[24];
/** Offset 0x040E - PCIE RP Unsupported Request Report
Indicate whether the Unsupported Request Report is enabled.
**/
UINT8 PcieRpUnsupportedRequestReport[24];
/** Offset 0x0426 - PCIE RP Fatal Error Report
Indicate whether the Fatal Error Report is enabled.
**/
UINT8 PcieRpFatalErrorReport[24];
/** Offset 0x043E - PCIE RP No Fatal Error Report
Indicate whether the No Fatal Error Report is enabled.
**/
UINT8 PcieRpNoFatalErrorReport[24];
/** Offset 0x0456 - PCIE RP Correctable Error Report
Indicate whether the Correctable Error Report is enabled.
**/
UINT8 PcieRpCorrectableErrorReport[24];
/** Offset 0x046E - PCIE RP System Error On Fatal Error
Indicate whether the System Error on Fatal Error is enabled.
**/
UINT8 PcieRpSystemErrorOnFatalError[24];
/** Offset 0x0486 - PCIE RP System Error On Non Fatal Error
Indicate whether the System Error on Non Fatal Error is enabled.
**/
UINT8 PcieRpSystemErrorOnNonFatalError[24];
/** Offset 0x049E - PCIE RP System Error On Correctable Error
Indicate whether the System Error on Correctable Error is enabled.
**/
UINT8 PcieRpSystemErrorOnCorrectableError[24];
/** Offset 0x04B6 - PCIE RP Max Payload
Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD.
**/
UINT8 PcieRpMaxPayload[24];
/** Offset 0x04CE - PCIE RP Device Reset Pad Active High
Indicated whether PERST# is active 0: Low; 1: High, See: DeviceResetPad.
**/
UINT8 PcieRpDeviceResetPadActiveHigh[24];
/** Offset 0x04E6 - PCIE RP Pcie Speed
Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3 (see:
PCH_PCIE_SPEED).
**/
UINT8 PcieRpPcieSpeed[24];
/** Offset 0x04FE - PCIE RP Gen3 Equalization Phase Method
PCIe Gen3 Eq Ph3 Method (see PCH_PCIE_EQ_METHOD). 0: Default; 2: Software Search;
4: Fixed Coeficients.
**/
UINT8 PcieRpGen3EqPh3Method[24];
/** Offset 0x0516 - PCIE RP Physical Slot Number
Indicates the slot number for the root port. Default is the value as root port index.
**/
UINT8 PcieRpPhysicalSlotNumber[24];
/** Offset 0x052E - PCIE RP Completion Timeout
The root port completion timeout(see: PCH_PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default.
**/
UINT8 PcieRpCompletionTimeout[24];
/** Offset 0x0546
**/
UINT8 UnusedUpdSpace13[2];
/** Offset 0x0548 - PCIE RP Device Reset Pad
The PCH pin assigned to device PERST# signal if available, zero otherwise. See
also DeviceResetPadActiveHigh.
**/
UINT32 PcieRpDeviceResetPad[24];
/** Offset 0x05A8 - PCIE RP Aspm
The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is
PchPcieAspmAutoConfig.
**/
UINT8 PcieRpAspm[24];
/** Offset 0x05C0 - PCIE RP L1 Substates
The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL).
Default is PchPcieL1SubstatesL1_1_2.
**/
UINT8 PcieRpL1Substates[24];
/** Offset 0x05D8 - PCIE RP Ltr Enable
Latency Tolerance Reporting Mechanism.
**/
UINT8 PcieRpLtrEnable[24];
/** Offset 0x05F0 - PCIE RP Ltr Config Lock
0: Disable; 1: Enable.
**/
UINT8 PcieRpLtrConfigLock[24];
/** Offset 0x0608 - PCIE Eq Ph3 Lane Param Cm
PCH_PCIE_EQ_LANE_PARAM. Coefficient C-1.
**/
UINT8 PcieEqPh3LaneParamCm[24];
/** Offset 0x0620 - PCIE Eq Ph3 Lane Param Cp
PCH_PCIE_EQ_LANE_PARAM. Coefficient C+1.
**/
UINT8 PcieEqPh3LaneParamCp[24];
/** Offset 0x0638 - PCIE RP Clock Power Management
Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
can still be controlled by L1 PM substates mechanism
**/
UINT8 PcieRpEnableCpm[24];
/** Offset 0x0650 - PCIE RP Detect Timeout Ms
The number of milliseconds within 0~65535 in reference code will wait for link to
exit Detect state for enabled ports before assuming there is no device and potentially
disabling the port.
**/
UINT16 PcieRpDetectTimeoutMs[24];
/** Offset 0x0680 - PCIE Sw Eq CoeffList Cm
PCH_PCIE_EQ_PARAM. Coefficient C-1.
**/
UINT8 PcieSwEqCoeffListCm[5];
/** Offset 0x0685 - PCIE Sw Eq CoeffList Cp
PCH_PCIE_EQ_PARAM. Coefficient C+1.
**/
UINT8 PcieSwEqCoeffListCp[5];
/** Offset 0x068A - PCIE Disable RootPort Clock Gating
Describes whether the PCI Express Clock Gating for each root port is enabled by
platform modules. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PcieDisableRootPortClockGating;
/** Offset 0x068B - PCIE Enable Peer Memory Write
This member describes whether Peer Memory Writes are enabled on the platform.
$EN_DIS
**/
UINT8 PcieEnablePeerMemoryWrite;
/** Offset 0x068C - PCIE Allow No Ltr Icc PLL Shutdown
Allows BIOS to control ICC PLL Shutdown by determining PCIe devices are LTR capable
or leaving untouched.
$EN_DIS
**/
UINT8 PcieAllowNoLtrIccPllShutdown;
/** Offset 0x068D - PCIE Compliance Test Mode
Compliance Test Mode shall be enabled when using Compliance Load Board.
$EN_DIS
**/
UINT8 PcieComplianceTestMode;
/** Offset 0x068E - PCIE Rp Function Swap
Allows BIOS to use root port function number swapping when root port of function
0 is disabled.
$EN_DIS
**/
UINT8 PcieRpFunctionSwap;
/** Offset 0x068F - PCH Pm PME_B0_S5_DIS
When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1.
$EN_DIS
**/
UINT8 PchPmPmeB0S5Dis;
/** Offset 0x0690 - PCH Pm Slp S0 Voltage Margining Enable
Indicates platform has support for VCCPrim_Core Voltage Margining in SLP_S0# asserted state.
$EN_DIS
**/
UINT8 PchPmSlpS0VmEnable;
/** Offset 0x0691 - PCH Pm Wol Enable Override
Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register.
$EN_DIS
**/
UINT8 PchPmWolEnableOverride;
/** Offset 0x0692 - PCH Pm Pcie Wake From DeepSx
Determine if enable PCIe to wake from deep Sx.
$EN_DIS
**/
UINT8 PchPmPcieWakeFromDeepSx;
/** Offset 0x0693 - PCH Pm WoW lan Enable
Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register.
$EN_DIS
**/
UINT8 PchPmWoWlanEnable;
/** Offset 0x0694 - PCH Pm WoW lan DeepSx Enable
Determine if WLAN wake from DeepSx, corresponds to the DSX_WLAN_PP_EN bit in the
PWRM_CFG3 register.
$EN_DIS
**/
UINT8 PchPmWoWlanDeepSxEnable;
/** Offset 0x0695 - PCH Pm Lan Wake From DeepSx
Determine if enable LAN to wake from deep Sx.
$EN_DIS
**/
UINT8 PchPmLanWakeFromDeepSx;
/** Offset 0x0696 - PCH Pm Deep Sx Pol
Deep Sx Policy.
$EN_DIS
**/
UINT8 PchPmDeepSxPol;
/** Offset 0x0697 - PCH Pm Slp S3 Min Assert
SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms.
**/
UINT8 PchPmSlpS3MinAssert;
/** Offset 0x0698 - PCH Pm Slp S4 Min Assert
SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s.
**/
UINT8 PchPmSlpS4MinAssert;
/** Offset 0x0699 - PCH Pm Slp Sus Min Assert
SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s.
**/
UINT8 PchPmSlpSusMinAssert;
/** Offset 0x069A - PCH Pm Slp A Min Assert
SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s.
**/
UINT8 PchPmSlpAMinAssert;
/** Offset 0x069B - PCH Pm Lpc Clock Run
This member describes whether or not the LPC ClockRun feature of PCH should be enabled.
$EN_DIS
**/
UINT8 PchPmLpcClockRun;
/** Offset 0x069C - PCH Pm Slp Strch Sus Up
Enable SLP_X Stretching After SUS Well Power Up.
$EN_DIS
**/
UINT8 PchPmSlpStrchSusUp;
/** Offset 0x069D - PCH Pm Slp Lan Low Dc
Enable/Disable SLP_LAN# Low on DC Power.
$EN_DIS
**/
UINT8 PchPmSlpLanLowDc;
/** Offset 0x069E - PCH Pm Pwr Btn Override Period
PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s.
**/
UINT8 PchPmPwrBtnOverridePeriod;
/** Offset 0x069F - PCH Pm Disable Dsx Ac Present Pulldown
When Disable, PCH will internal pull down AC_PRESENT in deep SX and during G3 exit.
$EN_DIS
**/
UINT8 PchPmDisableDsxAcPresentPulldown;
/** Offset 0x06A0 - PCH Pm Disable Native Power Button
Power button native mode disable.
$EN_DIS
**/
UINT8 PchPmDisableNativePowerButton;
/** Offset 0x06A1 - PCH Pm Slp S0 Enable
Indicates whether SLP_S0# is to be asserted when PCH reaches idle state.
$EN_DIS
**/
UINT8 PchPmSlpS0Enable;
/** Offset 0x06A2 - PCH Pm ME_WAKE_STS
Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register.
$EN_DIS
**/
UINT8 PchPmMeWakeSts;
/** Offset 0x06A3 - PCH Pm WOL_OVR_WK_STS
Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register.
$EN_DIS
**/
UINT8 PchPmWolOvrWkSts;
/** Offset 0x06A4 - PCH Pm Reset Power Cycle Duration
Could be customized in the unit of second. Please refer to EDS for all support settings.
0 is default, 1 is 1 second, 2 is 2 seconds, ...
**/
UINT8 PchPmPwrCycDur;
/** Offset 0x06A5 - PCH Port 61h Config Enable/Disable
Used for the emulation feature for Port61h read. The port is trapped and the SMI
handler will toggle bit4 according to the handler's internal state.
$EN_DIS
**/
UINT8 PchPort61hEnable;
/** Offset 0x06A6 - PCH Sata Pwr Opt Enable
SATA Power Optimizer on PCH side.
$EN_DIS
**/
UINT8 SataPwrOptEnable;
/** Offset 0x06A7 - PCH Sata eSATA Speed Limit
When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed.
$EN_DIS
**/
UINT8 EsataSpeedLimit;
/** Offset 0x06A8 - PCH Sata Speed Limit
Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault.
**/
UINT8 SataSpeedLimit;
/** Offset 0x06A9 - Enable SATA Port HotPlug
Enable SATA Port HotPlug.
**/
UINT8 SataPortsHotPlug[8];
/** Offset 0x06B1 - Enable SATA Port Interlock Sw
Enable SATA Port Interlock Sw.
**/
UINT8 SataPortsInterlockSw[8];
/** Offset 0x06B9 - Enable SATA Port External
Enable SATA Port External.
**/
UINT8 SataPortsExternal[8];
/** Offset 0x06C1 - Enable SATA Port SpinUp
Enable the COMRESET initialization Sequence to the device.
**/
UINT8 SataPortsSpinUp[8];
/** Offset 0x06C9 - Enable SATA Port Solid State Drive
0: HDD; 1: SSD.
**/
UINT8 SataPortsSolidStateDrive[8];
/** Offset 0x06D1 - Enable SATA Port Enable Dito Config
Enable DEVSLP Idle Timeout settings (DmVal, DitoVal).
**/
UINT8 SataPortsEnableDitoConfig[8];
/** Offset 0x06D9 - Enable SATA Port DmVal
DITO multiplier. Default is 15.
**/
UINT8 SataPortsDmVal[8];
/** Offset 0x06E1
**/
UINT8 UnusedUpdSpace14[1];
/** Offset 0x06E2 - Enable SATA Port DmVal
DEVSLP Idle Timeout (DITO), Default is 625.
**/
UINT16 SataPortsDitoVal[8];
/** Offset 0x06F2 - Enable SATA Port ZpOdd
Support zero power ODD.
**/
UINT8 SataPortsZpOdd[8];
/** Offset 0x06FA - PCH Sata Rst Raid Alternate Id
Enable RAID Alternate ID.
0:Client, 1:Alternate, 2:Server
**/
UINT8 SataRstRaidAlternateId;
/** Offset 0x06FB - PCH Sata Rst Raid0
RAID0.
$EN_DIS
**/
UINT8 SataRstRaid0;
/** Offset 0x06FC - PCH Sata Rst Raid1
RAID1.
$EN_DIS
**/
UINT8 SataRstRaid1;
/** Offset 0x06FD - PCH Sata Rst Raid10
RAID10.
$EN_DIS
**/
UINT8 SataRstRaid10;
/** Offset 0x06FE - PCH Sata Rst Raid5
RAID5.
$EN_DIS
**/
UINT8 SataRstRaid5;
/** Offset 0x06FF - PCH Sata Rst Irrt
Intel Rapid Recovery Technology.
$EN_DIS
**/
UINT8 SataRstIrrt;
/** Offset 0x0700 - PCH Sata Rst Orom Ui Banner
OROM UI and BANNER.
$EN_DIS
**/
UINT8 SataRstOromUiBanner;
/** Offset 0x0701 - PCH Sata Rst Orom Ui Delay
00b: 2 secs; 01b: 4 secs; 10b: 6 secs; 11: 8 secs (see: PCH_SATA_OROM_DELAY).
**/
UINT8 SataRstOromUiDelay;
/** Offset 0x0702 - PCH Sata Rst Hdd Unlock
Indicates that the HDD password unlock in the OS is enabled.
$EN_DIS
**/
UINT8 SataRstHddUnlock;
/** Offset 0x0703 - PCH Sata Rst Led Locate
Indicates that the LED/SGPIO hardware is attached and ping to locate feature is
enabled on the OS.
$EN_DIS
**/
UINT8 SataRstLedLocate;
/** Offset 0x0704 - PCH Sata Rst Irrt Only
Allow only IRRT drives to span internal and external ports.
$EN_DIS
**/
UINT8 SataRstIrrtOnly;
/** Offset 0x0705 - PCH Sata Rst Smart Storage
RST Smart Storage caching Bit.
$EN_DIS
**/
UINT8 SataRstSmartStorage;
/** Offset 0x0706 - PCH Sata Rst Pcie Storage Remap enable
Enable Intel RST for PCIe Storage remapping.
**/
UINT8 SataRstPcieEnable[3];
/** Offset 0x0709 - PCH Sata Rst Pcie Storage Port
Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect).
**/
UINT8 SataRstPcieStoragePort[3];
/** Offset 0x070C - PCH Sata Rst Pcie Device Reset Delay
PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
**/
UINT8 SataRstPcieDeviceResetDelay[3];
/** Offset 0x070F - Enable eMMC HS400 Training
Determine if HS400 Training is required.
$EN_DIS
**/
UINT8 PchScsEmmcHs400TuningRequired;
/** Offset 0x0710 - Set HS400 Tuning Data Valid
Set if HS400 Tuning Data Valid.
$EN_DIS
**/
UINT8 PchScsEmmcHs400DllDataValid;
/** Offset 0x0711 - Rx Strobe Delay Control
Rx Strobe Delay Control - Rx Strobe Delay DLL 1 (HS400 Mode).
**/
UINT8 PchScsEmmcHs400RxStrobeDll1;
/** Offset 0x0712 - Tx Data Delay Control
Tx Data Delay Control 1 - Tx Data Delay (HS400 Mode).
**/
UINT8 PchScsEmmcHs400TxDataDll;
/** Offset 0x0713 - I/O Driver Strength
I/O driver strength: 0 - 33 Ohm, 1 - 40 Ohm, 2 - 50 Ohm.
**/
UINT8 PchScsEmmcHs400DriverStrength;
/** Offset 0x0714 - Enable Pch Serial IO GPIO
Determines if enable Serial IO GPIO.
$EN_DIS
**/
UINT8 SerialIoGpio;
/** Offset 0x0715 - IO voltage for I2C controllers
Selects the IO voltage for I2C controllers, 0: PchSerialIoIs33V, 1: PchSerialIoIs18V.
**/
UINT8 SerialIoI2cVoltage[6];
/** Offset 0x071B - Enable Serial IRQ
Determines if enable Serial IRQ.
$EN_DIS
**/
UINT8 PchSirqEnable;
/** Offset 0x071C - Serial IRQ Mode Select
Serial IRQ Mode Select, 0: quiet mode, 1: continuous mode.
$EN_DIS
**/
UINT8 PchSirqMode;
/** Offset 0x071D - Start Frame Pulse Width
Start Frame Pulse Width, 0: PchSfpw4Clk, 1: PchSfpw6Clk, 2: PchSfpw8Clk.
**/
UINT8 PchStartFramePulse;
/** Offset 0x071E - Enable Thermal Device
Enable Thermal Device.
$EN_DIS
**/
UINT8 PchThermalDeviceEnable;
/** Offset 0x071F
**/
UINT8 UnusedUpdSpace15;
/** Offset 0x0720 - Thermal Throttling Custimized T0Level Value
Custimized T0Level value.
**/
UINT16 PchT0Level;
/** Offset 0x0722 - Thermal Throttling Custimized T1Level Value
Custimized T1Level value.
**/
UINT16 PchT1Level;
/** Offset 0x0724 - Thermal Throttling Custimized T2Level Value
Custimized T2Level value.
**/
UINT16 PchT2Level;
/** Offset 0x0726 - Thermal Device SMI Enable
This locks down SMI Enable on Alert Thermal Sensor Trip.
$EN_DIS
**/
UINT8 PchTsmicLock;
/** Offset 0x0727 - Enable The Thermal Throttle
Enable the thermal throttle function.
$EN_DIS
**/
UINT8 PchTTEnable;
/** Offset 0x0728 - PMSync State 13
When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force
at least T2 state.
$EN_DIS
**/
UINT8 PchTTState13Enable;
/** Offset 0x0729 - Thermal Throttle Lock
Thermal Throttle Lock.
$EN_DIS
**/
UINT8 PchTTLock;
/** Offset 0x072A - Thermal Throttling Suggested Setting
Thermal Throttling Suggested Setting.
$EN_DIS
**/
UINT8 TTSuggestedSetting;
/** Offset 0x072B - Enable PCH Cross Throttling
Enable/Disable PCH Cross Throttling
$EN_DIS
**/
UINT8 TTCrossThrottling;
/** Offset 0x072C - DMI Thermal Sensor Autonomous Width Enable
DMI Thermal Sensor Autonomous Width Enable.
$EN_DIS
**/
UINT8 PchDmiTsawEn;
/** Offset 0x072D - DMI Thermal Sensor Suggested Setting
DMT thermal sensor suggested representative values.
$EN_DIS
**/
UINT8 DmiSuggestedSetting;
/** Offset 0x072E - Thermal Sensor 0 Target Width
Thermal Sensor 0 Target Width.
**/
UINT8 DmiTS0TW;
/** Offset 0x072F - Thermal Sensor 1 Target Width
Thermal Sensor 1 Target Width.
**/
UINT8 DmiTS1TW;
/** Offset 0x0730 - Thermal Sensor 2 Target Width
Thermal Sensor 2 Target Width.
**/
UINT8 DmiTS2TW;
/** Offset 0x0731 - Thermal Sensor 3 Target Width
Thermal Sensor 3 Target Width.
**/
UINT8 DmiTS3TW;
/** Offset 0x0732 - Port 0 T1 Multipler
Port 0 T1 Multipler.
**/
UINT8 SataP0T1M;
/** Offset 0x0733 - Port 0 T2 Multipler
Port 0 T2 Multipler.
**/
UINT8 SataP0T2M;
/** Offset 0x0734 - Port 0 T3 Multipler
Port 0 T3 Multipler.
**/
UINT8 SataP0T3M;
/** Offset 0x0735 - Port 0 Tdispatch
Port 0 Tdispatch.
**/
UINT8 SataP0TDisp;
/** Offset 0x0736 - Port 1 T1 Multipler
Port 1 T1 Multipler.
**/
UINT8 SataP1T1M;
/** Offset 0x0737 - Port 1 T2 Multipler
Port 1 T2 Multipler.
**/
UINT8 SataP1T2M;
/** Offset 0x0738 - Port 1 T3 Multipler
Port 1 T3 Multipler.
**/
UINT8 SataP1T3M;
/** Offset 0x0739 - Port 1 Tdispatch
Port 1 Tdispatch.
**/
UINT8 SataP1TDisp;
/** Offset 0x073A - Port 0 Tinactive
Port 0 Tinactive.
**/
UINT8 SataP0Tinact;
/** Offset 0x073B - Port 0 Alternate Fast Init Tdispatch
Port 0 Alternate Fast Init Tdispatch.
$EN_DIS
**/
UINT8 SataP0TDispFinit;
/** Offset 0x073C - Port 1 Tinactive
Port 1 Tinactive.
**/
UINT8 SataP1Tinact;
/** Offset 0x073D - Port 1 Alternate Fast Init Tdispatch
Port 1 Alternate Fast Init Tdispatch.
$EN_DIS
**/
UINT8 SataP1TDispFinit;
/** Offset 0x073E - Sata Thermal Throttling Suggested Setting
Sata Thermal Throttling Suggested Setting.
$EN_DIS
**/
UINT8 SataThermalSuggestedSetting;
/** Offset 0x073F - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
$EN_DIS
**/
UINT8 PchMemoryThrottlingEnable;
/** Offset 0x0740 - Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryPmsyncEnable[2];
/** Offset 0x0742 - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryC0TransmitEnable[2];
/** Offset 0x0744 - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryPinSelection[2];
/** Offset 0x0746 - Thermal Device Temperature
Decides the temperature.
**/
UINT16 PchTemperatureHotLevel;
/** Offset 0x0748 - Disable XHCI Compliance Mode
This policy will disable XHCI compliance mode on all ports. Complicance Mode should
be default enabled.
$EN_DIS
**/
UINT8 PchDisableComplianceMode;
/** Offset 0x0749 - USB2 Port Over Current Pin
Describe the specific over current pin number of USB 2.0 Port N.
**/
UINT8 Usb2OverCurrentPin[16];
/** Offset 0x0759 - USB3 Port Over Current Pin
Describe the specific over current pin number of USB 3.0 Port N.
**/
UINT8 Usb3OverCurrentPin[10];
/** Offset 0x0763 - Enable 8254 Static Clock Gating in early POST time
Set 8254CGE=1 is required for C11 support. However, set 8254CGE=1 in POST time might
fail to boot legacy OS which using 8254 timer. Make sure it won't break legacy
OS boot before enabling this.
$EN_DIS
**/
UINT8 Early8254ClockGatingEnable;
/** Offset 0x0764 - PCH Sata Rst Optane Memory
Optane Memory
$EN_DIS
**/
UINT8 SataRstOptaneMemory;
/** Offset 0x0765 - PCH SATA RST CPU attached storage
RST CPU attached storage
$EN_DIS
**/
UINT8 SataRstCpuAttachedStorage;
/** Offset 0x0766
**/
UINT8 UnusedUpdSpace16[2];
/** Offset 0x0768 - Pch PCIE device override table pointer
The PCIe device table is being used to override PCIe device ASPM settings. This
is a pointer points to a 32bit address. And it's only used in PostMem phase. Please
refer to PCH_PCIE_DEVICE_OVERRIDE structure for the table. Last entry VendorId
must be 0.
**/
UINT32 PchPcieDeviceOverrideTablePtr;
/** Offset 0x076C - Enable TCO timer.
When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have
huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer
emulation must be enabled, and WDAT table must not be exposed to the OS.
$EN_DIS
**/
UINT8 EnableTcoTimer;
/** Offset 0x076D - Enable PS_ON.
PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power
target that will be required by the California Energy Commission (CEC). When FALSE,
PS_ON is to be disabled.
$EN_DIS
**/
UINT8 PsOnEnable;
/** Offset 0x076E - ReservedPchPostMem
Reserved for Pch Post-Mem
$EN_DIS
**/
UINT8 ReservedPchPostMem[16];
/** Offset 0x077E
**/
UINT8 UnusedUpdSpace17[2];
/** Offset 0x0780 - BgpdtHash[4]
BgpdtHash values
**/
UINT64 BgpdtHash[4];
/** Offset 0x07A0 - BiosGuardAttr
BiosGuardAttr default values
**/
UINT32 BiosGuardAttr;
/** Offset 0x07A4
**/
UINT8 UnusedUpdSpace18[4];
/** Offset 0x07A8 - BiosGuardModulePtr
BiosGuardModulePtr default values
**/
UINT64 BiosGuardModulePtr;
/** Offset 0x07B0 - SendEcCmd
SendEcCmd function pointer. \n
@code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE
EcCmdType, IN UINT8 EcCmd, IN UINT8 SendData, IN OUT UINT8 *ReceiveData); @endcode
**/
UINT64 SendEcCmd;
/** Offset 0x07B8 - EcCmdProvisionEav
Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC
**/
UINT8 EcCmdProvisionEav;
/** Offset 0x07B9 - EcCmdLock
EcCmdLock default values. Locks Ephemeral Authorization Value sent previously
**/
UINT8 EcCmdLock;
/** Offset 0x07BA
**/
UINT8 UnusedUpdSpace19[6];
/** Offset 0x07C0 - SgxEpoch0
SgxEpoch0 default values
**/
UINT64 SgxEpoch0;
/** Offset 0x07C8 - SgxEpoch1
SgxEpoch1 default values
**/
UINT64 SgxEpoch1;
/** Offset 0x07D0 - SgxSinitNvsData
SgxSinitNvsData default values
**/
UINT8 SgxSinitNvsData;
/** Offset 0x07D1 - Si Config CSM Flag.
Platform specific common policies that used by several silicon components. CSM status flag.
$EN_DIS
**/
UINT8 SiCsmFlag;
/** Offset 0x07D2
**/
UINT8 UnusedUpdSpace20[2];
/** Offset 0x07D4 - SVID SDID table Poniter.
The address of the table of SVID SDID to customize each SVID SDID entry.
**/
UINT32 SiSsidTablePtr;
/** Offset 0x07D8 - Number of ssid table.
SiNumberOfSsidTableEntry should match the table entries created in SiSsidTablePtr.
**/
UINT16 SiNumberOfSsidTableEntry;
/** Offset 0x07DA - SATA RST Interrupt Mode
Allowes to choose which interrupts will be implemented by SATA controller in RAID mode.
0:Msix, 1:Msi, 2:Legacy
**/
UINT8 SataRstInterrupt;
/** Offset 0x07DB - ME Unconfig on RTC clear
0: Disable ME Unconfig On Rtc Clear. 1: Enable ME Unconfig On Rtc Clear.
2: Cmos is clear, status unkonwn. 3: Reserved
0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos
is clear, 3: Reserved
**/
UINT8 MeUnconfigOnRtcClear;
/** Offset 0x07DC
**/
UINT8 UnusedUpdSpace21[3];
/** Offset 0x07DF
**/
UINT8 ReservedFspsUpd[1];
} FSP_S_CONFIG;
/** Fsp S Test Configuration
**/
typedef struct {
/** Offset 0x07E0
**/
UINT32 Signature;
/** Offset 0x07E4 - Enable/Disable Device 7
Enable: Device 7 enabled, Disable (Default): Device 7 disabled
$EN_DIS
**/
UINT8 ChapDeviceEnable;
/** Offset 0x07E5 - Skip PAM register lock
Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
PAM registers will be locked by RC
$EN_DIS
**/
UINT8 SkipPamLock;
/** Offset 0x07E6 - EDRAM Test Mode
Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
PAM registers will be locked by RC
0: EDRAM SW disable, 1: EDRAM SW Enable, 2: EDRAM HW mode
**/
UINT8 EdramTestMode;
/** Offset 0x07E7 - DMI Extended Sync Control
Enable: Enable DMI Extended Sync Control, Disable(Default): Disable DMI Extended
Sync Control
$EN_DIS
**/
UINT8 DmiExtSync;
/** Offset 0x07E8 - DMI IOT Control
Enable: Enable DMI IOT Control, Disable(Default): Disable DMI IOT Control
$EN_DIS
**/
UINT8 DmiIot;
/** Offset 0x07E9 - PEG Max Payload size per root port
0xFF(Default):Auto, 0x1: Force 128B, 0x2: Force 256B
0xFF: Auto, 0x1: Force 128B, 0x2: Force 256B
**/
UINT8 PegMaxPayload[4];
/** Offset 0x07ED - Enable/Disable IGFX RenderStandby
Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby
$EN_DIS
**/
UINT8 RenderStandby;
/** Offset 0x07EE - Enable/Disable IGFX PmSupport
Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport
$EN_DIS
**/
UINT8 PmSupport;
/** Offset 0x07EF - Enable/Disable CdynmaxClamp
Enable(Default): Enable CdynmaxClamp, Disable: Disable CdynmaxClamp
$EN_DIS
**/
UINT8 CdynmaxClampEnable;
/** Offset 0x07F0 - Disable VT-d
0=Enable/FALSE(VT-d enabled), 1=Disable/TRUE (VT-d disabled)
$EN_DIS
**/
UINT8 VtdDisableDeprecated;
/** Offset 0x07F1 - GT Frequency Limit
0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
0x18: 1200 Mhz
0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
0x18: 1200 Mhz
**/
UINT8 GtFreqMax;
/** Offset 0x07F2 - Disable Turbo GT
0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency
$EN_DIS
**/
UINT8 DisableTurboGt;
/** Offset 0x07F3 - SaPostMemTestRsvd
Reserved for SA Post-Mem Test
$EN_DIS
**/
UINT8 SaPostMemTestRsvd[11];
/** Offset 0x07FE - 1-Core Ratio Limit
1-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 1-Core
Ratio Limit Must be greater than or equal to 2-Core Ratio Limit, 3-Core Ratio Limit,
4-Core Ratio Limit, 5-Core Ratio Limit, 6-Core Ratio Limit, 7-Core Ratio Limit,
8-Core Ratio Limit. Range is 0 to 255
**/
UINT8 OneCoreRatioLimit;
/** Offset 0x07FF - 2-Core Ratio Limit
2-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 2-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
**/
UINT8 TwoCoreRatioLimit;
/** Offset 0x0800 - 3-Core Ratio Limit
3-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 3-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
**/
UINT8 ThreeCoreRatioLimit;
/** Offset 0x0801 - 4-Core Ratio Limit
4-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 4-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
**/
UINT8 FourCoreRatioLimit;
/** Offset 0x0802 - Enable or Disable HWP
Enable or Disable HWP(Hardware P states) Support. 0: Disable; 1: Enable;
2-3:Reserved
$EN_DIS
**/
UINT8 Hwp;
/** Offset 0x0803 - Hardware Duty Cycle Control
Hardware Duty Cycle Control configuration. 0: Disabled; 1: Enabled 2-3:Reserved
$EN_DIS
**/
UINT8 HdcControl;
/** Offset 0x0804 - Package Long duration turbo mode time
Package Long duration turbo mode time window in seconds. 0 = AUTO, uses 28 seconds.
Valid values(Unit in seconds) 1 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40
, 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
UINT8 PowerLimit1Time;
/** Offset 0x0805 - Short Duration Turbo Mode
Enable or Disable short duration Turbo Mode. 0 : Disable; 1: Enable
$EN_DIS
**/
UINT8 PowerLimit2;
/** Offset 0x0806 - Turbo settings Lock
Lock all Turbo settings Enable/Disable; 0: Disable , 1: Enable
$EN_DIS
**/
UINT8 TurboPowerLimitLock;
/** Offset 0x0807 - Package PL3 time window
Package PL3 time window range for this policy from 0 to 64ms
**/
UINT8 PowerLimit3Time;
/** Offset 0x0808 - Package PL3 Duty Cycle
Package PL3 Duty Cycle; Valid Range is 0 to 100
**/
UINT8 PowerLimit3DutyCycle;
/** Offset 0x0809 - Package PL3 Lock
Package PL3 Lock Enable/Disable; 0: Disable ; 1: Enable
$EN_DIS
**/
UINT8 PowerLimit3Lock;
/** Offset 0x080A - Package PL4 Lock
Package PL4 Lock Enable/Disable; 0: Disable ; 1: Enable
$EN_DIS
**/
UINT8 PowerLimit4Lock;
/** Offset 0x080B - TCC Activation Offset
TCC Activation Offset. Offset from factory set TCC activation temperature at which
the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation
Temperature, in volts.For Y SKU, the recommended default for this policy is 15,
For all other SKUs the recommended default are 0
**/
UINT8 TccActivationOffset;
/** Offset 0x080C - Tcc Offset Clamp Enable/Disable
Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle
below P1.For Y SKU, the recommended default for this policy is 1: Enabled,
For all other SKUs the recommended default are 0: Disabled.
$EN_DIS
**/
UINT8 TccOffsetClamp;
/** Offset 0x080D - Tcc Offset Lock
Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature
target; 0: Disabled; 1: Enabled.
$EN_DIS
**/
UINT8 TccOffsetLock;
/** Offset 0x080E - Custom Ratio State Entries
The number of custom ratio state entries, ranges from 0 to 40 for a valid custom
ratio table.Sets the number of custom P-states. At least 2 states must be present
**/
UINT8 NumberOfEntries;
/** Offset 0x080F - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 1. Valid Range 0
to 128, 0 = AUTO
**/
UINT8 Custom1PowerLimit1Time;
/** Offset 0x0810 - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 1. Valid Range 0 to 255
**/
UINT8 Custom1TurboActivationRatio;
/** Offset 0x0811 - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom1ConfigTdpControl;
/** Offset 0x0812 - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 2. Valid Range 0
to 128, 0 = AUTO
**/
UINT8 Custom2PowerLimit1Time;
/** Offset 0x0813 - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 2. Valid Range 0 to 255
**/
UINT8 Custom2TurboActivationRatio;
/** Offset 0x0814 - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom2ConfigTdpControl;
/** Offset 0x0815 - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 3. Valid Range 0
to 128, 0 = AUTO
**/
UINT8 Custom3PowerLimit1Time;
/** Offset 0x0816 - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 3. Valid Range 0 to 255
**/
UINT8 Custom3TurboActivationRatio;
/** Offset 0x0817 - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom3ConfigTdpControl;
/** Offset 0x0818 - ConfigTdp mode settings Lock
Lock the ConfigTdp mode settings from runtime changes; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ConfigTdpLock;
/** Offset 0x0819 - Load Configurable TDP SSDT
Configure whether to load Configurable TDP SSDT; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ConfigTdpBios;
/** Offset 0x081A - PL1 Enable value
PL1 Enable value to limit average platform power. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PsysPowerLimit1;
/** Offset 0x081B - PL1 timewindow
PL1 timewindow in seconds. 0 = AUTO, uses 28 seconds. Valid values(Unit in seconds)
1 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
UINT8 PsysPowerLimit1Time;
/** Offset 0x081C - PL2 Enable Value
PL2 Enable activates the PL2 value to limit average platform power.0: Disable;
1: Enable.
$EN_DIS
**/
UINT8 PsysPowerLimit2;
/** Offset 0x081D - Enable or Disable MLC Streamer Prefetcher
Enable or Disable MLC Streamer Prefetcher; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MlcStreamerPrefetcher;
/** Offset 0x081E - Enable or Disable MLC Spatial Prefetcher
Enable or Disable MLC Spatial Prefetcher; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 MlcSpatialPrefetcher;
/** Offset 0x081F - Enable or Disable Monitor /MWAIT instructions
Enable or Disable Monitor /MWAIT instructions; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MonitorMwaitEnable;
/** Offset 0x0820 - Enable or Disable initialization of machine check registers
Enable or Disable initialization of machine check registers; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MachineCheckEnable;
/** Offset 0x0821 - Deprecated DO NOT USE Enable or Disable processor debug features
@deprecated Enable or Disable processor debug features; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DebugInterfaceEnable;
/** Offset 0x0822 - Lock or Unlock debug interface features
Lock or Unlock debug interface features; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DebugInterfaceLockEnable;
/** Offset 0x0823 - AP Idle Manner of waiting for SIPI
AP Idle Manner of waiting for SIPI; 1: HALT loop; 2: MWAIT loop; 3: RUN loop.
1: HALT loop, 2: MWAIT loop, 3: RUN loop
**/
UINT8 ApIdleManner;
/** Offset 0x0824 - Control on Processor Trace output scheme
Control on Processor Trace output scheme; 0: Single Range Output; 1: ToPA Output.
0: Single Range Output, 1: ToPA Output
**/
UINT8 ProcessorTraceOutputScheme;
/** Offset 0x0825 - Enable or Disable Processor Trace feature
Enable or Disable Processor Trace feature; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ProcessorTraceEnable;
/** Offset 0x0826
**/
UINT8 UnusedUpdSpace22[2];
/** Offset 0x0828 - Base of memory region allocated for Processor Trace
Base address of memory region allocated for Processor Trace. Processor Trace requires
2^N alignment and size in bytes per thread, from 4KB to 128MB. 0: Disable
**/
UINT64 ProcessorTraceMemBase;
/** Offset 0x0830 - Memory region allocation for Processor Trace
Length in bytes of memory region allocated for Processor Trace. Processor Trace
requires 2^N alignment and size in bytes per thread, from 4KB to 128MB. 0: Disable
**/
UINT32 ProcessorTraceMemLength;
/** Offset 0x0834 - Enable or Disable Voltage Optimization feature
Enable or Disable Voltage Optimization feature 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 VoltageOptimization;
/** Offset 0x0835 - Enable or Disable Intel SpeedStep Technology
Enable or Disable Intel SpeedStep Technology. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 Eist;
/** Offset 0x0836 - Enable or Disable Energy Efficient P-state
Enable or Disable Energy Efficient P-state will be applied in Turbo mode. Disable;
1: Enable
$EN_DIS
**/
UINT8 EnergyEfficientPState;
/** Offset 0x0837 - Enable or Disable Energy Efficient Turbo
Enable or Disable Energy Efficient Turbo, will be applied in Turbo mode. Disable;
1: Enable
$EN_DIS
**/
UINT8 EnergyEfficientTurbo;
/** Offset 0x0838 - Enable or Disable T states
Enable or Disable T states; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 TStates;
/** Offset 0x0839 - Enable or Disable Bi-Directional PROCHOT#
Enable or Disable Bi-Directional PROCHOT#; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 BiProcHot;
/** Offset 0x083A - Enable or Disable PROCHOT# signal being driven externally
Enable or Disable PROCHOT# signal being driven externally; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DisableProcHotOut;
/** Offset 0x083B - Enable or Disable PROCHOT# Response
Enable or Disable PROCHOT# Response; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ProcHotResponse;
/** Offset 0x083C - Enable or Disable VR Thermal Alert
Enable or Disable VR Thermal Alert; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DisableVrThermalAlert;
/** Offset 0x083D - Enable or Disable Thermal Reporting
Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 AutoThermalReporting;
/** Offset 0x083E - Enable or Disable Thermal Monitor
Enable or Disable Thermal Monitor; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ThermalMonitor;
/** Offset 0x083F - Enable or Disable CPU power states (C-states)
Enable or Disable CPU power states (C-states). 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 Cx;
/** Offset 0x0840 - Configure C-State Configuration Lock
Configure C-State Configuration Lock; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PmgCstCfgCtrlLock;
/** Offset 0x0841 - Enable or Disable Enhanced C-states
Enable or Disable Enhanced C-states. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 C1e;
/** Offset 0x0842 - Enable or Disable Package Cstate Demotion
Enable or Disable Package Cstate Demotion. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 PkgCStateDemotion;
/** Offset 0x0843 - Enable or Disable Package Cstate UnDemotion
Enable or Disable Package Cstate UnDemotion. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 PkgCStateUnDemotion;
/** Offset 0x0844 - Enable or Disable CState-Pre wake
Enable or Disable CState-Pre wake. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 CStatePreWake;
/** Offset 0x0845 - Enable or Disable TimedMwait Support.
Enable or Disable TimedMwait Support. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 TimedMwait;
/** Offset 0x0846 - Enable or Disable IO to MWAIT redirection
Enable or Disable IO to MWAIT redirection; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 CstCfgCtrIoMwaitRedirection;
/** Offset 0x0847 - Set the Max Pkg Cstate
Set the Max Pkg Cstate. Default set to Auto which limits the Max Pkg Cstate to deep
C-state. Valid values 0 - C0/C1 , 1 - C2 , 2 - C3 , 3 - C6 , 4 - C7 , 5 - C7S ,
6 - C8 , 7 - C9 , 8 - C10 , 254 - CPU Default , 255 - Auto
**/
UINT8 PkgCStateLimit;
/** Offset 0x0848 - TimeUnit for C-State Latency Control0
TimeUnit for C-State Latency Control0; Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl0TimeUnit;
/** Offset 0x0849 - TimeUnit for C-State Latency Control1
TimeUnit for C-State Latency Control1;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl1TimeUnit;
/** Offset 0x084A - TimeUnit for C-State Latency Control2
TimeUnit for C-State Latency Control2;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl2TimeUnit;
/** Offset 0x084B - TimeUnit for C-State Latency Control3
TimeUnit for C-State Latency Control3;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl3TimeUnit;
/** Offset 0x084C - TimeUnit for C-State Latency Control4
Time - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl4TimeUnit;
/** Offset 0x084D - TimeUnit for C-State Latency Control5
TimeUnit for C-State Latency Control5;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl5TimeUnit;
/** Offset 0x084E - Interrupt Redirection Mode Select
Interrupt Redirection Mode Select.0: Fixed priority; 1: Round robin;2: Hash vector;4:
PAIR with fixed priority;5: PAIR with round robin;6: PAIR with hash vector;7: No change.
**/
UINT8 PpmIrmSetting;
/** Offset 0x084F - Lock prochot configuration
Lock prochot configuration Enable/Disable; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ProcHotLock;
/** Offset 0x0850 - Configuration for boot TDP selection
Configuration for boot TDP selection; 0: TDP Nominal; 1: TDP Down; 2: TDP
Up;0xFF : Deactivate
**/
UINT8 ConfigTdpLevel;
/** Offset 0x0851 - Race To Halt
Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency
in order to enter pkg C-State faster to reduce overall power. (RTH is controlled
through MSR 1FC bit 20)Disable; 1: Enable
$EN_DIS
**/
UINT8 RaceToHalt;
/** Offset 0x0852 - Max P-State Ratio
Max P-State Ratio, Valid Range 0 to 0x7F
**/
UINT8 MaxRatio;
/** Offset 0x0853 - P-state ratios for custom P-state table
P-state ratios for custom P-state table. NumberOfEntries has valid range between
0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries]
are configurable. Valid Range of each entry is 0 to 0x7F
**/
UINT8 StateRatio[40];
/** Offset 0x087B - P-state ratios for max 16 version of custom P-state table
P-state ratios for max 16 version of custom P-state table. This table is used for
OS versions limited to a max of 16 P-States. If the first entry of this table is
0, or if Number of Entries is 16 or less, then this table will be ignored, and
up to the top 16 values of the StateRatio table will be used instead. Valid Range
of each entry is 0 to 0x7F
**/
UINT8 StateRatioMax16[16];
/** Offset 0x088B
**/
UINT8 UnusedUpdSpace23;
/** Offset 0x088C - Platform Power Pmax
PCODE MMIO Mailbox: Platform Power Pmax. 0 - Auto Specified in 1/8 Watt increments.
Range 0-1024 Watts. Value of 800 = 100W
**/
UINT16 PsysPmax;
/** Offset 0x088E - Interrupt Response Time Limit of C-State LatencyContol0
Interrupt Response Time Limit of C-State LatencyContol0.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl0Irtl;
/** Offset 0x0890 - Interrupt Response Time Limit of C-State LatencyContol1
Interrupt Response Time Limit of C-State LatencyContol1.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl1Irtl;
/** Offset 0x0892 - Interrupt Response Time Limit of C-State LatencyContol2
Interrupt Response Time Limit of C-State LatencyContol2.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl2Irtl;
/** Offset 0x0894 - Interrupt Response Time Limit of C-State LatencyContol3
Interrupt Response Time Limit of C-State LatencyContol3.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl3Irtl;
/** Offset 0x0896 - Interrupt Response Time Limit of C-State LatencyContol4
Interrupt Response Time Limit of C-State LatencyContol4.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl4Irtl;
/** Offset 0x0898 - Interrupt Response Time Limit of C-State LatencyContol5
Interrupt Response Time Limit of C-State LatencyContol5.Range of value 0 to 0x3FF
**/
UINT16 CstateLatencyControl5Irtl;
/** Offset 0x089A
**/
UINT8 UnusedUpdSpace24[2];
/** Offset 0x089C - Package Long duration turbo mode power limit
Package Long duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit1;
/** Offset 0x08A0 - Package Short duration turbo mode power limit
Package Short duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit2Power;
/** Offset 0x08A4 - Package PL3 power limit
Package PL3 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit3;
/** Offset 0x08A8 - Package PL4 power limit
Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 1023875 in Step size of 125
**/
UINT32 PowerLimit4;
/** Offset 0x08AC - Tcc Offset Time Window for RATL
Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 1023875 in Step size of 125
**/
UINT32 TccOffsetTimeWindowForRatl;
/** Offset 0x08B0 - Short term Power Limit value for custom cTDP level 1
Short term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom1PowerLimit1;
/** Offset 0x08B4 - Long term Power Limit value for custom cTDP level 1
Long term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom1PowerLimit2;
/** Offset 0x08B8 - Short term Power Limit value for custom cTDP level 2
Short term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom2PowerLimit1;
/** Offset 0x08BC - Long term Power Limit value for custom cTDP level 2
Long term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom2PowerLimit2;
/** Offset 0x08C0 - Short term Power Limit value for custom cTDP level 3
Short term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom3PowerLimit1;
/** Offset 0x08C4 - Long term Power Limit value for custom cTDP level 3
Long term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom3PowerLimit2;
/** Offset 0x08C8 - Platform PL1 power
Platform PL1 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
0 to 4095875 in Step size of 125
**/
UINT32 PsysPowerLimit1Power;
/** Offset 0x08CC - Platform PL2 power
Platform PL2 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
0 to 4095875 in Step size of 125
**/
UINT32 PsysPowerLimit2Power;
/** Offset 0x08D0 - Set Three Strike Counter Disable
False (default): Three Strike counter will be incremented and True: Prevents Three
Strike counter from incrementing; 0: False; 1: True.
0: False, 1: True
**/
UINT8 ThreeStrikeCounterDisable;
/** Offset 0x08D1 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT
Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 HwpInterruptControl;
/** Offset 0x08D2 - 5-Core Ratio Limit
5-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 5-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
0x0:0xFF
**/
UINT8 FiveCoreRatioLimit;
/** Offset 0x08D3 - 6-Core Ratio Limit
6-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 6-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
0x0:0xFF
**/
UINT8 SixCoreRatioLimit;
/** Offset 0x08D4 - 7-Core Ratio Limit
7-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 7-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
0x0:0xFF
**/
UINT8 SevenCoreRatioLimit;
/** Offset 0x08D5 - 8-Core Ratio Limit
8-Core Ratio Limit: LFM to Fused, For overclocking part: LFM to 255. This 8-Core
Ratio Limit Must be Less than or equal to 1-Core Ratio Limit.Range is 0 to 255
0x0:0xFF
**/
UINT8 EightCoreRatioLimit;
/** Offset 0x08D6 - Intel Turbo Boost Max Technology 3.0
Intel Turbo Boost Max Technology 3.0. 0: Disabled; 1: Enabled
$EN_DIS
**/
UINT8 EnableItbm;
/** Offset 0x08D7 - Intel Turbo Boost Max Technology 3.0 Driver
Intel Turbo Boost Max Technology 3.0 Driver 0: Disabled; 1: Enabled
$EN_DIS
**/
UINT8 EnableItbmDriver;
/** Offset 0x08D8 - Enable or Disable C1 Cstate Demotion
Enable or Disable C1 Cstate Demotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C1StateAutoDemotion;
/** Offset 0x08D9 - Enable or Disable C1 Cstate UnDemotion
Enable or Disable C1 Cstate UnDemotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C1StateUnDemotion;
/** Offset 0x08DA - CpuWakeUpTimer
Enable long CPU Wakeup Timer. When enabled, the cpu internal wakeup time is increased
to 180 seconds. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 CpuWakeUpTimer;
/** Offset 0x08DB - Minimum Ring ratio limit override
Minimum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo
ratio limit
**/
UINT8 MinRingRatioLimit;
/** Offset 0x08DC - Minimum Ring ratio limit override
Maximum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo
ratio limit
**/
UINT8 MaxRingRatioLimit;
/** Offset 0x08DD - Enable or Disable C3 Cstate Demotion
Enable or Disable C3 Cstate Demotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C3StateAutoDemotion;
/** Offset 0x08DE - Enable or Disable C3 Cstate UnDemotion
Enable or Disable C3 Cstate UnDemotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C3StateUnDemotion;
/** Offset 0x08DF - ReservedCpuPostMemTest
Reserved for CPU Post-Mem Test
$EN_DIS
**/
UINT8 ReservedCpuPostMemTest[19];
/** Offset 0x08F2 - SgxSinitDataFromTpm
SgxSinitDataFromTpm default values
**/
UINT8 SgxSinitDataFromTpm;
/** Offset 0x08F3 - End of Post message
Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1):
EOP send in PEI, Send in DXE(0x2)(Default): EOP send in PEI
0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved
**/
UINT8 EndOfPostMessage;
/** Offset 0x08F4 - D0I3 Setting for HECI Disable
Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all
HECI devices
$EN_DIS
**/
UINT8 DisableD0I3SettingForHeci;
/** Offset 0x08F5 - Enable LOCKDOWN SMI
Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.
$EN_DIS
**/
UINT8 PchLockDownGlobalSmi;
/** Offset 0x08F6 - HD Audio Reset Wait Timer
The delay timer after Azalia reset, the value is number of microseconds. Default is 600.
**/
UINT16 PchHdaResetWaitTimer;
/** Offset 0x08F8 - Enable LOCKDOWN BIOS Interface
Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register.
$EN_DIS
**/
UINT8 PchLockDownBiosInterface;
/** Offset 0x08F9 - RTC CMOS RAM LOCK
Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper
and and lower 128-byte bank of RTC RAM.
$EN_DIS
**/
UINT8 PchLockDownRtcLock;
/** Offset 0x08FA - PCH Sbi lock bit
This unlock the SBI lock bit to allow SBI after post time. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchSbiUnlock;
/** Offset 0x08FB - PCH Psf lock bit
The PSF registers will be locked before 3rd party code execution. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchSbAccessUnlock;
/** Offset 0x08FC - PCIE RP Ltr Max Snoop Latency
Latency Tolerance Reporting, Max Snoop Latency.
**/
UINT16 PcieRpLtrMaxSnoopLatency[24];
/** Offset 0x092C - PCIE RP Ltr Max No Snoop Latency
Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
UINT16 PcieRpLtrMaxNoSnoopLatency[24];
/** Offset 0x095C - PCIE RP Snoop Latency Override Mode
Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
UINT8 PcieRpSnoopLatencyOverrideMode[24];
/** Offset 0x0974 - PCIE RP Snoop Latency Override Multiplier
Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
UINT8 PcieRpSnoopLatencyOverrideMultiplier[24];
/** Offset 0x098C - PCIE RP Snoop Latency Override Value
Latency Tolerance Reporting, Snoop Latency Override Value.
**/
UINT16 PcieRpSnoopLatencyOverrideValue[24];
/** Offset 0x09BC - PCIE RP Non Snoop Latency Override Mode
Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
UINT8 PcieRpNonSnoopLatencyOverrideMode[24];
/** Offset 0x09D4 - PCIE RP Non Snoop Latency Override Multiplier
Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
UINT8 PcieRpNonSnoopLatencyOverrideMultiplier[24];
/** Offset 0x09EC - PCIE RP Non Snoop Latency Override Value
Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
UINT16 PcieRpNonSnoopLatencyOverrideValue[24];
/** Offset 0x0A1C - PCIE RP Slot Power Limit Scale
Specifies scale used for slot power limit value. Leave as 0 to set to default.
**/
UINT8 PcieRpSlotPowerLimitScale[24];
/** Offset 0x0A34 - PCIE RP Slot Power Limit Value
Specifies upper limit on power supplie by slot. Leave as 0 to set to default.
**/
UINT16 PcieRpSlotPowerLimitValue[24];
/** Offset 0x0A64 - PCIE RP Upstream Port Transmiter Preset
Used during Gen3 Link Equalization. Used for all lanes. Default is 5.
**/
UINT8 PcieRpUptp[24];
/** Offset 0x0A7C - PCIE RP Downstream Port Transmiter Preset
Used during Gen3 Link Equalization. Used for all lanes. Default is 7.
**/
UINT8 PcieRpDptp[24];
/** Offset 0x0A94 - PCIE RP Enable Port8xh Decode
This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable;
1: Enable.
$EN_DIS
**/
UINT8 PcieEnablePort8xhDecode;
/** Offset 0x0A95 - PCIE Port8xh Decode Port Index
The Index of PCIe Port that is selected for Port8xh Decode (0 Based).
**/
UINT8 PchPciePort8xhDecodePortIndex;
/** Offset 0x0A96 - PCH Pm Disable Energy Report
Disable/Enable PCH to CPU enery report feature.
$EN_DIS
**/
UINT8 PchPmDisableEnergyReport;
/** Offset 0x0A97 - PCH Sata Test Mode
Allow entrance to the PCH SATA test modes.
$EN_DIS
**/
UINT8 SataTestMode;
/** Offset 0x0A98 - PCH USB OverCurrent mapping lock enable
If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning
that OC mapping data will be consumed by xHCI and OC mapping registers will be locked.
$EN_DIS
**/
UINT8 PchXhciOcLock;
/** Offset 0x0A99 - Xhci OverCurrent enable
Xhci Overcurrent enable.
$EN_DIS
**/
UINT8 PchXhciOcEnable;
/** Offset 0x0A9A - ReservedPchPostMemTest
Reserved for Pch Post-Mem
$EN_DIS
**/
UINT8 ReservedPchPostMem[16];
/** Offset 0x0AAA - Mctp Broadcast Cycle
Test, Determine if MCTP Broadcast is enabled 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MctpBroadcastCycle;
/** Offset 0x0AAB
**/
UINT8 UnusedUpdSpace25[1];
/** Offset 0x0AAC
**/
UINT8 ReservedFspsTestUpd[12];
} FSP_S_TEST_CONFIG;
/** Fsp S UPD Configuration
**/
typedef struct {
/** Offset 0x0000
**/
FSP_UPD_HEADER FspUpdHeader;
/** Offset 0x0020
**/
FSP_S_CONFIG FspsConfig;
/** Offset 0x07E0
**/
FSP_S_TEST_CONFIG FspsTestConfig;
/** Offset 0x0AB8
**/
UINT8 UnusedUpdSpace26[6];
/** Offset 0x0ABE
**/
UINT16 UpdTerminator;
} FSPS_UPD;
#pragma pack()
#endif