/* SPDX-License-Identifier: GPL-2.0-only */ #include #include #include #include #include #include #include #include #include "sch5545.h" int sch5545_get_gpio(uint8_t sio_port, uint8_t gpio) { struct device *dev; uint16_t runtime_reg_base; uint8_t gpio_bank, gpio_num; gpio_bank = gpio / 10; gpio_num = gpio % 10; /* * GPIOs are divided into banks of 8 GPIOs (kind of). Each group starts * at decimal base, i.e. 8 GPIOs from GPIO000, 8 GPIOs from GPIO010, * etc., up to GPIO071 and GPIO072 which are an exception (only two * gpios in the bank 7). */ if (gpio_num > 7) return -1; else if (gpio_bank == 7 && gpio_num > 1) return -1; else if (gpio_bank > 7) return -1; dev = dev_find_slot_pnp(sio_port, SCH5545_LDN_LPC); if (!dev) { printk(BIOS_ERR, "%s: ERROR: LPC interface LDN not present." "Check the devicetree!\n", __func__); return -1; } pnp_enter_conf_mode(dev); pnp_set_logical_device(dev); runtime_reg_base = pnp_read_config(dev, SCH5545_BAR_RUNTIME_REG + 2); runtime_reg_base |= pnp_read_config(dev, SCH5545_BAR_RUNTIME_REG + 3) << 8; pnp_exit_conf_mode(dev); if (runtime_reg_base == 0) return -1; outb(gpio_bank * 8 + gpio_num, runtime_reg_base + SCH5545_RR_GPIO_SEL); return inb(runtime_reg_base + SCH5545_RR_GPIO_READ) & 1; } static void sch5545_init(struct device *dev) { if (!dev->enabled) return; switch (dev->path.pnp.device) { case SCH5545_LDN_KBC: pnp_enter_conf_mode(dev); pnp_set_logical_device(dev); /* Disable PS/2 clock and data isolation */ pnp_unset_and_set_config(dev, 0xf0, SCH5545_KBD_ISOLATION | SCH5545_MOUSE_ISOLATION, 0); pnp_exit_conf_mode(dev); pc_keyboard_init(NO_AUX_DEVICE); break; case SCH5545_LDN_LPC: pnp_enter_conf_mode(dev); pnp_set_logical_device(dev); /* Enable SERIRQ */ pnp_write_config(dev, 0x24, pnp_read_config(dev, 0x24) | 0x04); pnp_exit_conf_mode(dev); break; } } static void sch5545_set_iobase(struct device *dev, u8 index, u16 iobase) { u8 val; struct device *lpc_if; u8 iobase_reg = 0; lpc_if = dev_find_slot_pnp(dev->path.pnp.port, SCH5545_LDN_LPC); if (!lpc_if) { printk(BIOS_ERR, "ERROR: %s LPC interface LDN not present." "Check the devicetree!\n", dev_path(dev)); return; } switch (dev->path.pnp.device) { case SCH5545_LDN_EMI: iobase_reg = SCH5545_BAR_EM_IF; break; case SCH5545_LDN_KBC: iobase_reg = SCH5545_BAR_KBC; break; case SCH5545_LDN_UART1: iobase_reg = SCH5545_BAR_UART1; break; case SCH5545_LDN_UART2: iobase_reg = SCH5545_BAR_UART2; break; case SCH5545_LDN_RR: iobase_reg = SCH5545_BAR_RUNTIME_REG; break; case SCH5545_LDN_FDC: iobase_reg = SCH5545_BAR_FLOPPY; break; case SCH5545_LDN_LPC: iobase_reg = SCH5545_BAR_LPC_IF; break; case SCH5545_LDN_PP: iobase_reg = SCH5545_BAR_PARPORT; break; default: return; } pnp_set_logical_device(lpc_if); /* Flip the bytes in IO base, LSB goes first */ pnp_write_config(lpc_if, iobase_reg + 2, iobase & 0xff); pnp_write_config(lpc_if, iobase_reg + 3, (iobase >> 8) & 0xff); /* Set valid bit */ val = pnp_read_config(lpc_if, iobase_reg + 1); val |= 0x80; pnp_write_config(lpc_if, iobase_reg + 1, val); pnp_set_logical_device(dev); } static void sch5545_set_irq(struct device *dev, u8 index, u8 irq) { u8 select_bit = 0; struct device *lpc_if; /* In case it is not the IRQ, write misc register directly */ if (index >= PNP_IDX_MSC0) { pnp_write_config(dev, index, irq); return; } lpc_if = dev_find_slot_pnp(dev->path.pnp.port, SCH5545_LDN_LPC); if (!lpc_if) { printk(BIOS_ERR, "ERROR: %s LPC interface LDN not present." "Check the devicetree!\n", dev_path(dev)); return; } pnp_set_logical_device(lpc_if); /* * Some LDNs can generate IRQs from two sources, i.e. * - EMI may generate interrupts for Mailbox and INT source register * - KBC may generate separate IRQ for mouse and keyboard, * - RR LDN may generate IRQ for PME and SMI etc. * SELECT bit allows to distinguish IRQ source for single LDN. * Use the standard IRQs for devices. */ switch (dev->path.pnp.device) { case SCH5545_LDN_EMI: case SCH5545_LDN_KBC: case SCH5545_LDN_RR: if (index == 0x72) select_bit = 0x80; break; default: break; } /* * IRQs are set in a little different manner. Each IRQ number has its * own register which is programmed with LDN number which should use * the IRQ. Ignore the index offset and choose register based on IRQ * number counting from IRQ base. */ pnp_write_config(lpc_if, SCH5545_IRQ_BASE + irq, dev->path.pnp.device | select_bit); pnp_set_logical_device(dev); } static void sch5545_set_drq(struct device *dev, u8 index, u8 drq) { struct device *lpc_if; if (drq == 4) { printk(BIOS_ERR, "ERROR: %s %02x: Trying to set reserved DMA channel 4!\n", dev_path(dev), index); printk(BIOS_ERR, "This configuration is untested. Trying to continue.\n"); } /* DMA channel is programmed via LPC LDN */ lpc_if = dev_find_slot_pnp(dev->path.pnp.port, SCH5545_LDN_LPC); if (!lpc_if) { printk(BIOS_ERR, "ERROR: %s LPC interface LDN not present." "Check the devicetree!\n", dev_path(dev)); return; } pnp_set_logical_device(lpc_if); /* * There are 8 configurable DMA channels. DRQs are set in a little * different manner. Each DMA channel has its own 16-bit register which * is programmed with LDN number (in higher byte) which should use the * IRQ. Ignore the index offset and choose register based on IRQ number * counting from IRQ base. Set valid bit (bit 7) additionally. */ pnp_write_config(dev, SCH5545_DRQ_BASE + (drq * 2) + 1, dev->path.pnp.device | 0x80); pnp_set_logical_device(dev); } static void sch5545_set_resource(struct device *dev, struct resource *resource) { if (!(resource->flags & IORESOURCE_ASSIGNED)) { /* * The PNP_MSC super IO registers have the IRQ flag set. If no * value is assigned in the devicetree, the corresponding * PNP_MSC register doesn't get written, which should be printed * as warning and not as error. */ if (resource->flags & IORESOURCE_IRQ && (resource->index != PNP_IDX_IRQ0) && (resource->index != PNP_IDX_IRQ1)) printk(BIOS_WARNING, "WARNING: %s %02lx %s size: " "0x%010llx not assigned\n", dev_path(dev), resource->index, resource_type(resource), resource->size); else printk(BIOS_ERR, "ERROR: %s %02lx %s size: 0x%010llx " "not assigned\n", dev_path(dev), resource->index, resource_type(resource), resource->size); return; } /* Now store the resource. */ if (resource->flags & IORESOURCE_IO) { sch5545_set_iobase(dev, resource->index, resource->base); } else if (resource->flags & IORESOURCE_DRQ) { sch5545_set_drq(dev, resource->index, resource->base); } else if (resource->flags & IORESOURCE_IRQ) { sch5545_set_irq(dev, resource->index, resource->base); } else { printk(BIOS_ERR, "ERROR: %s %02lx unknown resource type\n", dev_path(dev), resource->index); return; } resource->flags |= IORESOURCE_STORED; report_resource_stored(dev, resource, ""); } static void sch5545_set_resources(struct device *dev) { struct resource *res; pnp_enter_conf_mode(dev); /* Select the logical device (LDN). */ pnp_set_logical_device(dev); for (res = dev->resource_list; res; res = res->next) sch5545_set_resource(dev, res); pnp_exit_conf_mode(dev); } static struct device_operations ops = { .read_resources = pnp_read_resources, .set_resources = sch5545_set_resources, .enable_resources = pnp_enable_resources, .enable = pnp_alt_enable, .init = sch5545_init, .ops_pnp_mode = &pnp_conf_mode_55_aa, }; static struct pnp_info pnp_dev_info[] = { { NULL, SCH5545_LDN_EMI, PNP_IO0 | PNP_IRQ0 | PNP_IRQ1, 0x0ff0 }, { NULL, SCH5545_LDN_KBC, PNP_IO0 | PNP_IRQ0 | PNP_IRQ1 | PNP_MSC0 | PNP_MSC1, 0x0fff }, { NULL, SCH5545_LDN_UART1, PNP_IO0 | PNP_IRQ0 | PNP_MSC0, 0x0ff8 }, { NULL, SCH5545_LDN_UART2, PNP_IO0 | PNP_IRQ0 | PNP_MSC0, 0x0ff8 }, { NULL, SCH5545_LDN_RR, PNP_IO0 | PNP_IRQ0 | PNP_IRQ1 | PNP_MSC0, 0x0fc0 }, { NULL, SCH5545_LDN_FDC, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0 | PNP_MSC0 | PNP_MSC1 | PNP_MSC2 | PNP_MSC3 | PNP_MSC4 | PNP_MSC5, 0x0ff8, }, { NULL, SCH5545_LDN_LPC, PNP_IO0, 0x0ffe }, { NULL, SCH5545_LDN_PP, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0 | PNP_MSC0 | PNP_MSC1, 0x0ff8 }, }; static void enable_dev(struct device *dev) { pnp_enable_devices(dev, &ops, ARRAY_SIZE(pnp_dev_info), pnp_dev_info); } struct chip_operations superio_smsc_sch5545_ops = { CHIP_NAME("SMSC SCH5545 Super I/O") .enable_dev = enable_dev, };