/* * This file is part of the coreboot project. * * Copyright (C) 2007, 2008 Rudolf Marek * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License v2 as published by * the Free Software Foundation. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ /* Inspiration from other VIA SB code. */ #include #include #include #include #include #include #include #include #include #include #include "vt8237r.h" #include "chip.h" #define ALL (0xff << 24) #define NONE (0) #define DISABLED (1 << 16) #define ENABLED (0 << 16) #define TRIGGER_EDGE (0 << 15) #define TRIGGER_LEVEL (1 << 15) #define POLARITY_HIGH (0 << 13) #define POLARITY_LOW (1 << 13) #define PHYSICAL_DEST (0 << 11) #define LOGICAL_DEST (1 << 11) #define ExtINT (7 << 8) #define NMI (4 << 8) #define SMI (2 << 8) #define INT (1 << 8) extern void dump_south(device_t dev); static struct ioapicreg { u32 reg; u32 value_low; u32 value_high; } ioapic_table[] = { /* IO-APIC virtual wire mode configuration. */ /* mask, trigger, polarity, destination, delivery, vector */ {0, ENABLED | TRIGGER_EDGE | POLARITY_HIGH | PHYSICAL_DEST | ExtINT, NONE}, {1, DISABLED, NONE}, {2, DISABLED, NONE}, {3, DISABLED, NONE}, {4, DISABLED, NONE}, {5, DISABLED, NONE}, {6, DISABLED, NONE}, {7, DISABLED, NONE}, {8, DISABLED, NONE}, {9, DISABLED, NONE}, {10, DISABLED, NONE}, {11, DISABLED, NONE}, {12, DISABLED, NONE}, {13, DISABLED, NONE}, {14, DISABLED, NONE}, {15, DISABLED, NONE}, {16, DISABLED, NONE}, {17, DISABLED, NONE}, {18, DISABLED, NONE}, {19, DISABLED, NONE}, {20, DISABLED, NONE}, {21, DISABLED, NONE}, {22, DISABLED, NONE}, {23, DISABLED, NONE}, }; static void setup_ioapic(u32 ioapic_base) { u32 value_low, value_high, val; volatile u32 *l; int i; /* All delivered to CPU0. */ ioapic_table[0].value_high = (lapicid()) << (56 - 32); l = (unsigned long *)ioapic_base; /* Set APIC to FSB message bus. */ l[0] = 0x3; val = l[4]; l[4] = (val & 0xFFFFFE) | 1; /* Set APIC ADDR - this will be VT8237R_APIC_ID. */ l[0] = 0; val = l[4]; l[4] = (val & 0xF0FFFF) | (VT8237R_APIC_ID << 24); for (i = 0; i < ARRAY_SIZE(ioapic_table); i++) { l[0] = (ioapic_table[i].reg * 2) + 0x10; l[4] = ioapic_table[i].value_low; value_low = l[4]; l[0] = (ioapic_table[i].reg * 2) + 0x11; l[4] = ioapic_table[i].value_high; value_high = l[4]; if ((i == 0) && (value_low == 0xffffffff)) { printk_warning("IO APIC not responding.\n"); return; } } } static void southbridge_init_common(struct device *dev); /** Set up PCI IRQ routing, route everything through APIC. */ static void pci_routing_fixup(struct device *dev) { /* PCI PNP Interrupt Routing INTE/F - disable */ pci_write_config8(dev, 0x44, 0x00); /* PCI PNP Interrupt Routing INTG/H - disable */ pci_write_config8(dev, 0x45, 0x00); /* Route INTE-INTH through registers above, no map to INTA-INTD. */ pci_write_config8(dev, 0x46, 0x10); /* PCI Interrupt Polarity */ pci_write_config8(dev, 0x54, 0x00); /* PCI INTA# Routing */ pci_write_config8(dev, 0x55, 0x00); /* PCI INTB#/C# Routing */ pci_write_config8(dev, 0x56, 0x00); /* PCI INTD# Routing */ pci_write_config8(dev, 0x57, 0x00); } /** * Set up the power management capabilities directly into ACPI mode. * This avoids having to handle any System Management Interrupts (SMIs). */ extern u8 acpi_slp_type; static void setup_pm(device_t dev) { u16 tmp; /* Debounce LID and PWRBTN# Inputs for 16ms. */ pci_write_config8(dev, 0x80, 0x20); /* Set ACPI base address to I/O VT8237R_ACPI_IO_BASE. */ pci_write_config16(dev, 0x88, VT8237R_ACPI_IO_BASE | 0x1); /* Set ACPI to 9, must set IRQ 9 override to level! Set PSON gating. */ pci_write_config8(dev, 0x82, 0x40 | VT8237R_ACPI_IRQ); /* Primary interupt channel, define wake events 0=IRQ0 15=IRQ15 1=en. */ pci_write_config16(dev, 0x84, 0x30b2); /* SMI output level to low, 7.5us throttle clock */ pci_write_config8(dev, 0x8d, 0x18); /* GP Timer Control 1s */ pci_write_config8(dev, 0x93, 0x88); /* * 7 = SMBus clock from RTC 32.768KHz * 5 = Internal PLL reset from susp disabled * 2 = GPO2 is SUSA# */ pci_write_config8(dev, 0x94, 0xa0); /* * 7 = stp to sust delay 1msec * 6 = SUSST# Deasserted Before PWRGD for STD * 4 = PWRGOOD reset on VT8237A/S * 3 = GPO26/GPO27 is GPO * 2 = Disable Alert on Lan */ pci_write_config8(dev, 0x95, 0xcc); /* Disable GP3 timer. */ pci_write_config8(dev, 0x98, 0); /* Enable ACPI accessm RTC signal gated with PSON. */ pci_write_config8(dev, 0x81, 0x84); /* Clear status events. */ outw(0xffff, VT8237R_ACPI_IO_BASE + 0x00); outw(0xffff, VT8237R_ACPI_IO_BASE + 0x20); outw(0xffff, VT8237R_ACPI_IO_BASE + 0x28); outl(0xffffffff, VT8237R_ACPI_IO_BASE + 0x30); /* Disable SCI on GPIO. */ outw(0x0, VT8237R_ACPI_IO_BASE + 0x22); /* Disable SMI on GPIO. */ outw(0x0, VT8237R_ACPI_IO_BASE + 0x24); /* Disable all global enable SMIs. */ outw(0x0, VT8237R_ACPI_IO_BASE + 0x2a); /* All SMI off, both IDE buses ON, PSON rising edge. */ outw(0x0, VT8237R_ACPI_IO_BASE + 0x2c); /* Primary activity SMI disable. */ outl(0x0, VT8237R_ACPI_IO_BASE + 0x34); /* GP timer reload on none. */ outl(0x0, VT8237R_ACPI_IO_BASE + 0x38); /* Disable extended IO traps. */ outb(0x0, VT8237R_ACPI_IO_BASE + 0x42); /* SCI is generated for RTC/pwrBtn/slpBtn. */ tmp = inw(VT8237R_ACPI_IO_BASE + 0x04); #if HAVE_ACPI_RESUME == 1 acpi_slp_type = ((tmp & (7 << 10)) >> 10) == 1 ? 3 : 0 ; printk_debug("SLP_TYP type was %x %x\n", tmp, acpi_slp_type); #endif /* clear sleep */ tmp &= ~(7 << 10); tmp |= 1; outw(tmp, VT8237R_ACPI_IO_BASE + 0x04); } static void vt8237r_init(struct device *dev) { u8 enables; /* * Enable SATA LED, disable special CPU Frequency Change - * GPIO28 GPIO22 GPIO29 GPIO23 are GPIOs. */ pci_write_config8(dev, 0xe5, 0x9); /* REQ5 as PCI request input - should be together with INTE-INTH. */ pci_write_config8(dev, 0xe4, 0x4); /* Set bit 3 of 0x4f (use INIT# as CPU reset). */ enables = pci_read_config8(dev, 0x4f); enables |= 0x08; pci_write_config8(dev, 0x4f, enables); /* * Set Read Pass Write Control Enable * (force A2 from APIC FSB to low). */ pci_write_config8(dev, 0x48, 0x8c); southbridge_init_common(dev); /* FIXME: Intel needs more bit set for C2/C3. */ /* * Allow SLP# signal to assert LDTSTOP_L. * Will work for C3 and for FID/VID change. */ outb(0x1, VT8237R_ACPI_IO_BASE + 0x11); } static void vt8237s_init(struct device *dev) { u32 tmp; /* Put SPI base VT8237S_SPI_MEM_BASE. */ tmp = pci_read_config32(dev, 0xbc); pci_write_config32(dev, 0xbc, (VT8237S_SPI_MEM_BASE >> 8) | (tmp & 0xFF000000)); /* * REQ5 as PCI request input - should be together with INTE-INTH. */ pci_write_config8(dev, 0xe4, 0x04); /* Reduce further the STPCLK/LDTSTP signal to 5us. */ pci_write_config8(dev, 0xec, 0x4); /* Host Bus Power Management Control, maybe not needed */ pci_write_config8(dev, 0x8c, 0x5); /* Enable HPET at VT8237R_HPET_ADDR., does not work correctly on R. */ pci_write_config32(dev, 0x68, (VT8237R_HPET_ADDR | 0x80)); southbridge_init_common(dev); /* FIXME: Intel needs more bit set for C2/C3. */ /* * Allow SLP# signal to assert LDTSTOP_L. * Will work for C3 and for FID/VID change. FIXME FIXME, pre rev A2. */ outb(0xff, VT8237R_ACPI_IO_BASE + 0x50); dump_south(dev); } static void vt8237_common_init(struct device *dev) { u8 enables, byte; /* Enable addr/data stepping. */ byte = pci_read_config8(dev, PCI_COMMAND); byte |= PCI_COMMAND_WAIT; pci_write_config8(dev, PCI_COMMAND, byte); /* Enable the internal I/O decode. */ enables = pci_read_config8(dev, 0x6C); enables |= 0x80; pci_write_config8(dev, 0x6C, enables); /* * ROM decode * bit range * 7 000E0000h-000EFFFFh * 6 FFF00000h-FFF7FFFFh * 5 FFE80000h-FFEFFFFFh * 4 FFE00000h-FFE7FFFFh * 3 FFD80000h-FFDFFFFFh * 2 FFD00000h-FFD7FFFFh * 1 FFC80000h-FFCFFFFFh * 0 FFC00000h-FFC7FFFFh * So 0x7f here sets ROM decode to FFC00000-FFFFFFFF or 4Mbyte. */ pci_write_config8(dev, 0x41, 0x7f); /* * Set bit 6 of 0x40 (I/O recovery time). * IMPORTANT FIX - EISA = ECLR reg at 0x4d0! Decoding must be on so * that PCI interrupts can be properly marked as level triggered. */ enables = pci_read_config8(dev, 0x40); enables |= 0x44; pci_write_config8(dev, 0x40, enables); /* Line buffer control */ enables = pci_read_config8(dev, 0x42); enables |= 0xf8; pci_write_config8(dev, 0x42, enables); /* Delay transaction control */ pci_write_config8(dev, 0x43, 0xb); /* I/O recovery time, default IDE routing */ pci_write_config8(dev, 0x4c, 0x44); /* ROM memory cycles go to LPC. */ pci_write_config8(dev, 0x59, 0x80); /* * Bit | Meaning * ------------- * 3 | Bypass APIC De-Assert Message (1=Enable) * 1 | possibly "INTE#, INTF#, INTG#, INTH# as PCI" * | bit 1=1 works for Aaron at VIA, bit 1=0 works for jakllsch * 0 | Dynamic Clock Gating Main Switch (1=Enable) */ pci_write_config8(dev, 0x5b, 0xb); /* Set 0x58 to 0x43 APIC and RTC. */ pci_write_config8(dev, 0x58, 0x43); /* Enable serial IRQ, 6PCI clocks. */ pci_write_config8(dev, 0x52, 0x9); /* Power management setup */ setup_pm(dev); /* Start the RTC. */ rtc_init(0); } static void vt8237r_read_resources(device_t dev) { struct resource *res; pci_dev_read_resources(dev); /* Fixed APIC resource */ res = new_resource(dev, 0x44); res->base = VT8237R_APIC_BASE; res->size = 256; res->limit = res->base + res->size - 1; res->align = 8; res->gran = 8; res->flags = IORESOURCE_MEM | IORESOURCE_FIXED | IORESOURCE_STORED | IORESOURCE_ASSIGNED; } /** * The VT8237R is not a PCI bridge and has no resources of its own (other * than standard PC I/O addresses), however it does control the ISA bus * and so we need to manually call enable childrens resources on that bus. */ static void vt8237r_enable_resources(device_t dev) { pci_dev_enable_resources(dev); enable_childrens_resources(dev); } static void init_keyboard(struct device *dev) { u8 regval = pci_read_config8(dev, 0x51); if (regval & 0x1) init_pc_keyboard(0x60, 0x64, 0); } static void southbridge_init_common(struct device *dev) { vt8237_common_init(dev); pci_routing_fixup(dev); setup_ioapic(VT8237R_APIC_BASE); setup_i8259(); init_keyboard(dev); } static const struct device_operations vt8237r_lpc_ops_s = { .read_resources = vt8237r_read_resources, .set_resources = pci_dev_set_resources, .enable_resources = vt8237r_enable_resources, .init = &vt8237s_init, .scan_bus = scan_static_bus, }; static const struct device_operations vt8237r_lpc_ops_r = { .read_resources = vt8237r_read_resources, .set_resources = pci_dev_set_resources, .enable_resources = vt8237r_enable_resources, .init = &vt8237r_init, .scan_bus = scan_static_bus, }; static const struct pci_driver lpc_driver_r __pci_driver = { .ops = &vt8237r_lpc_ops_r, .vendor = PCI_VENDOR_ID_VIA, .device = PCI_DEVICE_ID_VIA_VT8237R_LPC, }; static const struct pci_driver lpc_driver_s __pci_driver = { .ops = &vt8237r_lpc_ops_s, .vendor = PCI_VENDOR_ID_VIA, .device = PCI_DEVICE_ID_VIA_VT8237S_LPC, };