/* SPDX-License-Identifier: GPL-2.0-only */ #include #include #include #include #include #include #include #include "chip.h" #include "iobp.h" #include "pch.h" #ifdef __SIMPLE_DEVICE__ static u8 *usb_xhci_mem_base(pci_devfn_t dev) #else static u8 *usb_xhci_mem_base(struct device *dev) #endif { u32 mem_base = pci_read_config32(dev, PCI_BASE_ADDRESS_0); /* Check if the controller is disabled or not present */ if (mem_base == 0 || mem_base == 0xffffffff) return 0; return (u8 *)(mem_base & ~0xf); } static int usb_xhci_port_count_usb3(u8 *mem_base) { if (!mem_base) { /* Do not proceed if BAR is invalid */ return 0; } if (pch_is_lp()) { /* LynxPoint-LP has 4 SS ports */ return 4; } /* LynxPoint-H can have 0, 2, 4, or 6 SS ports */ u32 fus = read32(mem_base + XHCI_USB3FUS); fus >>= XHCI_USB3FUS_SS_SHIFT; fus &= XHCI_USB3FUS_SS_MASK; switch (fus) { case 3: return 0; case 2: return 2; case 1: return 4; case 0: default: return 6; } } static void usb_xhci_reset_status_usb3(u8 *mem_base, int port) { u8 *portsc = mem_base + XHCI_USB3_PORTSC(port); u32 status = read32(portsc); /* Do not set Port Enabled/Disabled field */ status &= ~XHCI_USB3_PORTSC_PED; /* Clear all change status bits */ status |= XHCI_USB3_PORTSC_CHST; write32(portsc, status); } static void usb_xhci_reset_port_usb3(u8 *mem_base, int port) { u8 *portsc = mem_base + XHCI_USB3_PORTSC(port); write32(portsc, read32(portsc) | XHCI_USB3_PORTSC_WPR); } #define XHCI_RESET_DELAY_US 1000 /* 1ms */ #define XHCI_RESET_TIMEOUT 100 /* 100ms */ /* * 1) Wait until port is done polling * 2) If port is disconnected * a) Issue warm port reset * b) Poll for warm reset complete * c) Write 1 to port change status bits */ #ifdef __SIMPLE_DEVICE__ static void usb_xhci_reset_usb3(pci_devfn_t dev, int all) #else static void usb_xhci_reset_usb3(struct device *dev, int all) #endif { u32 status, port_disabled; int timeout, port; u8 *mem_base = usb_xhci_mem_base(dev); int port_count = usb_xhci_port_count_usb3(mem_base); if (!port_count) return; /* Get mask of disabled ports */ port_disabled = pci_read_config32(dev, XHCI_USB3PDO); /* Wait until all enabled ports are done polling */ for (timeout = XHCI_RESET_TIMEOUT; timeout; timeout--) { int complete = 1; for (port = 0; port < port_count; port++) { /* Skip disabled ports */ if (port_disabled & (1 << port)) continue; /* Read port link status field */ status = read32(mem_base + XHCI_USB3_PORTSC(port)); status &= XHCI_USB3_PORTSC_PLS; if (status == XHCI_PLSR_POLLING) complete = 0; } /* Exit if all ports not polling */ if (complete) break; udelay(XHCI_RESET_DELAY_US); } /* Reset all requested ports */ for (port = 0; port < port_count; port++) { u8 *portsc = mem_base + XHCI_USB3_PORTSC(port); /* Skip disabled ports */ if (port_disabled & (1 << port)) continue; status = read32(portsc) & XHCI_USB3_PORTSC_PLS; /* Reset all or only disconnected ports */ if (all || (status == XHCI_PLSR_RXDETECT || status == XHCI_PLSR_POLLING)) usb_xhci_reset_port_usb3(mem_base, port); else port_disabled |= 1 << port; } /* Wait for warm reset complete on all reset ports */ for (timeout = XHCI_RESET_TIMEOUT; timeout; timeout--) { int complete = 1; for (port = 0; port < port_count; port++) { /* Only check ports that were reset */ if (port_disabled & (1 << port)) continue; /* Check if warm reset is complete */ status = read32(mem_base + XHCI_USB3_PORTSC(port)); if (!(status & XHCI_USB3_PORTSC_WRC)) complete = 0; } /* Check for warm reset complete in any port */ if (complete) break; udelay(XHCI_RESET_DELAY_US); } /* Clear port change status bits */ for (port = 0; port < port_count; port++) usb_xhci_reset_status_usb3(mem_base, port); } #ifdef __SIMPLE_DEVICE__ /* Handler for XHCI controller on entry to S3/S4/S5 */ void usb_xhci_sleep_prepare(pci_devfn_t dev, u8 slp_typ) { u32 reg32; u8 *mem_base = usb_xhci_mem_base(dev); if (!mem_base || slp_typ < ACPI_S3) return; if (pch_is_lp()) { /* Set D0 state */ pci_update_config16(dev, XHCI_PWR_CTL_STS, ~PWR_CTL_SET_MASK, PWR_CTL_SET_D0); /* Clear PCI 0xB0[14:13] */ pci_and_config32(dev, 0xb0, ~((1 << 14) | (1 << 13))); /* Clear MMIO 0x816c[14,2] */ reg32 = read32(mem_base + 0x816c); reg32 &= ~((1 << 14) | (1 << 2)); write32(mem_base + 0x816c, reg32); /* Reset disconnected USB3 ports */ usb_xhci_reset_usb3(dev, 0); /* Set MMIO 0x80e0[15] */ reg32 = read32(mem_base + 0x80e0); reg32 |= (1 << 15); write32(mem_base + 0x80e0, reg32); } /* Set D3Hot state and enable PME */ pci_or_config16(dev, XHCI_PWR_CTL_STS, PWR_CTL_SET_D3); pci_or_config16(dev, XHCI_PWR_CTL_STS, PWR_CTL_STATUS_PME); pci_or_config16(dev, XHCI_PWR_CTL_STS, PWR_CTL_ENABLE_PME); } /* Route all ports to XHCI controller */ void usb_xhci_route_all(void) { u32 port_mask, route; /* Skip if EHCI is already disabled */ if (RCBA32(FD) & PCH_DISABLE_EHCI1) return; /* Set D0 state */ pci_update_config16(PCH_XHCI_DEV, XHCI_PWR_CTL_STS, ~PWR_CTL_SET_MASK, PWR_CTL_SET_D0); /* Set USB3 superspeed enable */ port_mask = pci_read_config32(PCH_XHCI_DEV, XHCI_USB3PRM); route = pci_read_config32(PCH_XHCI_DEV, XHCI_USB3PR); route &= ~XHCI_USB3PR_SSEN; route |= XHCI_USB3PR_SSEN & port_mask; pci_write_config32(PCH_XHCI_DEV, XHCI_USB3PR, route); /* Route USB2 ports to XHCI controller */ port_mask = pci_read_config32(PCH_XHCI_DEV, XHCI_USB2PRM); route = pci_read_config32(PCH_XHCI_DEV, XHCI_USB2PR); route &= ~XHCI_USB2PR_HCSEL; route |= XHCI_USB2PR_HCSEL & port_mask; pci_write_config32(PCH_XHCI_DEV, XHCI_USB2PR, route); /* Disable EHCI controller */ usb_ehci_disable(PCH_EHCI1_DEV); /* LynxPoint-H has a second EHCI controller */ if (!pch_is_lp()) usb_ehci_disable(PCH_EHCI2_DEV); /* Reset and clear port change status */ usb_xhci_reset_usb3(PCH_XHCI_DEV, 1); } #else /* !__SIMPLE_DEVICE__ */ static void usb_xhci_clock_gating(struct device *dev) { u32 reg32; /* IOBP 0xE5004001[7:6] = 11b */ pch_iobp_update(0xe5004001, ~0, (1 << 7) | (1 << 6)); reg32 = pci_read_config32(dev, 0x40); reg32 &= ~(1 << 23); /* unsupported request */ if (pch_is_lp()) { /* D20:F0:40h[18,17,8] = 111b */ reg32 |= (1 << 18) | (1 << 17) | (1 << 8); /* D20:F0:40h[21,20,19] = 110b to enable XHCI Idle L1 */ reg32 &= ~(1 << 19); reg32 |= (1 << 21) | (1 << 20); } else { /* D20:F0:40h[21,20,18,17,8] = 11111b */ reg32 |= (1 << 21) | (1 << 20) | (1 << 18) | (1 << 17) | (1 << 8); } /* Avoid writing upper byte as it is write-once */ pci_write_config16(dev, 0x40, (u16)(reg32 & 0xffff)); pci_write_config8(dev, 0x40 + 2, (u8)((reg32 >> 16) & 0xff)); /* D20:F0:44h[9,7,3] = 111b */ pci_or_config16(dev, 0x44, (1 << 9) | (1 << 7) | (1 << 3)); reg32 = pci_read_config32(dev, 0xa0); if (pch_is_lp()) { /* D20:F0:A0h[18] = 1 */ reg32 |= (1 << 18); } else { /* D20:F0:A0h[6] = 1 */ reg32 |= (1 << 6); } pci_write_config32(dev, 0xa0, reg32); /* D20:F0:A4h[13] = 0 */ pci_and_config32(dev, 0xa4, ~(1 << 13)); } static void usb_xhci_init(struct device *dev) { u32 reg32; u8 *mem_base = usb_xhci_mem_base(dev); struct southbridge_intel_lynxpoint_config *config = dev->chip_info; /* D20:F0:74h[1:0] = 00b (set D0 state) */ pci_update_config16(dev, XHCI_PWR_CTL_STS, ~PWR_CTL_SET_MASK, PWR_CTL_SET_D0); /* Enable clock gating first */ usb_xhci_clock_gating(dev); reg32 = read32(mem_base + 0x8144); if (pch_is_lp()) { /* XHCIBAR + 8144h[8,7,6] = 111b */ reg32 |= (1 << 8) | (1 << 7) | (1 << 6); } else { /* XHCIBAR + 8144h[8,7,6] = 100b */ reg32 &= ~((1 << 7) | (1 << 6)); reg32 |= (1 << 8); } write32(mem_base + 0x8144, reg32); if (pch_is_lp()) { /* XHCIBAR + 816Ch[19:0] = 000e0038h */ reg32 = read32(mem_base + 0x816c); reg32 &= ~0x000fffff; reg32 |= 0x000e0038; write32(mem_base + 0x816c, reg32); /* D20:F0:B0h[17,14,13] = 100b */ pci_update_config32(dev, 0xb0, ~((1 << 14) | (1 << 13)), 1 << 17); } reg32 = pci_read_config32(dev, 0x50); if (pch_is_lp()) { /* D20:F0:50h[28:0] = 0FCE2E5Fh */ reg32 &= ~0x1fffffff; reg32 |= 0x0fce2e5f; } else { /* D20:F0:50h[26:0] = 07886E9Fh */ reg32 &= ~0x07ffffff; reg32 |= 0x07886e9f; } pci_write_config32(dev, 0x50, reg32); /* D20:F0:44h[31] = 1 (Access Control Bit) */ pci_or_config32(dev, 0x44, 1 << 31); /* D20:F0:40h[31,23] = 10b (OC Configuration Done) */ pci_update_config32(dev, 0x40, ~(1 << 23), 1 << 31); /* unsupported request */ if (acpi_is_wakeup_s3()) { /* Reset ports that are disabled or * polling before returning to the OS. */ usb_xhci_reset_usb3(dev, 0); } else if (config && config->xhci_default) { /* Route all ports to XHCI */ apm_control(APM_CNT_ROUTE_ALL_XHCI); } } static struct device_operations usb_xhci_ops = { .read_resources = pci_dev_read_resources, .set_resources = pci_dev_set_resources, .enable_resources = pci_dev_enable_resources, .init = usb_xhci_init, .ops_pci = &pci_dev_ops_pci, }; static const unsigned short pci_device_ids[] = { PCI_DEVICE_ID_INTEL_LPT_H_XHCI, PCI_DEVICE_ID_INTEL_LPT_LP_XHCI, 0 }; static const struct pci_driver pch_usb_xhci __pci_driver = { .ops = &usb_xhci_ops, .vendor = PCI_VENDOR_ID_INTEL, .devices = pci_device_ids, }; #endif /* !__SIMPLE_DEVICE__ */