/* * This file is part of the coreboot project. * * Copyright (C) 2007-2008 coresystems GmbH * Copyright (C) 2014 Google Inc. * Copyright (C) 2015 Intel Corporation. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; version 2 of the License. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ #ifndef _SOC_CHIP_H_ #define _SOC_CHIP_H_ #include #include #include #include #include #include #include #include #include #define SKYLAKE_I2C_DEV_MAX 6 enum skylake_i2c_voltage { I2C_VOLTAGE_3V3, I2C_VOLTAGE_1V8 }; struct skylake_i2c_config { /* Bus voltage level, default is 3.3V */ enum skylake_i2c_voltage voltage; }; struct soc_intel_skylake_config { /* * Interrupt Routing configuration * If bit7 is 1, the interrupt is disabled. */ uint8_t pirqa_routing; uint8_t pirqb_routing; uint8_t pirqc_routing; uint8_t pirqd_routing; uint8_t pirqe_routing; uint8_t pirqf_routing; uint8_t pirqg_routing; uint8_t pirqh_routing; /* GPE configuration */ uint32_t gpe0_en_1; /* GPE0_EN_31_0 */ uint32_t gpe0_en_2; /* GPE0_EN_63_32 */ uint32_t gpe0_en_3; /* GPE0_EN_95_64 */ uint32_t gpe0_en_4; /* GPE0_EN_127_96 / GPE_STD */ /* Gpio group routed to each dword of the GPE0 block. Values are * of the form GPP_[A:G] or GPD. */ uint8_t gpe0_dw0; /* GPE0_31_0 STS/EN */ uint8_t gpe0_dw1; /* GPE0_63_32 STS/EN */ uint8_t gpe0_dw2; /* GPE0_95_64 STS/EN */ /* Generic IO decode ranges */ uint32_t gen1_dec; uint32_t gen2_dec; uint32_t gen3_dec; uint32_t gen4_dec; /* Enable S0iX support */ int s0ix_enable; /* Enable DPTF support */ int dptf_enable; /* Deep SX enable for both AC and DC */ int deep_s3_enable; int deep_s5_enable; /* * Deep Sx Configuration * DSX_EN_WAKE_PIN - Enable WAKE# pin * DSX_EN_LAN_WAKE_PIN - Enable LAN_WAKE# pin * DSX_EN_AC_PRESENT_PIN - Enable AC_PRESENT pin */ uint32_t deep_sx_config; /* TCC activation offset */ int tcc_offset; /* * The following fields come from FspUpdVpd.h. * These are configuration values that are passed to FSP during * MemoryInit. */ u64 PlatformMemorySize; u8 SmramMask; u8 MrcFastBoot; u32 TsegSize; u16 MmioSize; /* * DDR Frequency Limit * 0(Auto), 1067, 1333, 1600, 1867, 2133, 2400 */ u16 DdrFreqLimit; /* Probeless Trace function */ u8 ProbelessTrace; /* * System Agent dynamic frequency configuration * When enabled memory will be trained at two different frequencies. * 0 = Disabled * 1 = FixedLow * 2 = FixedHigh * 3 = Enabled */ u8 SaGv; /* Enable/disable Rank Margin Tool */ u8 Rmt; /* Lan */ u8 EnableLan; /* SATA related */ u8 EnableSata; u8 SataMode; u8 SataSalpSupport; u8 SataPortsEnable[8]; u8 SataPortsDevSlp[8]; /* Audio related */ u8 EnableAzalia; u8 DspEnable; /* * I/O Buffer Ownership: * 0: HD-A Link * 1 Shared, HD-A Link and I2S Port * 3: I2S Ports */ u8 IoBufferOwnership; /* Trace Hub function */ u8 EnableTraceHub; /* Pcie Root Ports */ u8 PcieRpEnable[20]; u8 PcieRpClkReqSupport[20]; u8 PcieRpClkReqNumber[20]; /* USB related */ struct usb2_port_config usb2_ports[16]; struct usb3_port_config usb3_ports[10]; u8 XdciEnable; u8 SsicPortEnable; /* SMBus */ u8 SmbusEnable; /* * SerialIO device mode selection: * * Device index: * PchSerialIoIndexI2C0 * PchSerialIoIndexI2C1 * PchSerialIoIndexI2C2 * PchSerialIoIndexI2C3 * PchSerialIoIndexI2C4 * PchSerialIoIndexI2C5 * PchSerialIoIndexI2C6 * PchSerialIoIndexSpi0 * PchSerialIoIndexSpi1 * PchSerialIoIndexUart0 * PchSerialIoIndexUart1 * PchSerialIoIndexUart2 * * Mode select: * PchSerialIoDisabled * PchSerialIoAcpi * PchSerialIoPci * PchSerialIoAcpiHidden * PchSerialIoLegacyUart */ u8 SerialIoDevMode[PchSerialIoIndexMax]; /* I2C */ struct skylake_i2c_config i2c[SKYLAKE_I2C_DEV_MAX]; /* Camera */ u8 Cio2Enable; /* eMMC and SD */ u8 ScsEmmcEnabled; u8 ScsEmmcHs400Enabled; u8 ScsSdCardEnabled; /* Integrated Sensor */ u8 IshEnable; u8 PttSwitch; u8 HeciTimeouts; u8 HsioMessaging; u8 Heci3Enabled; /* Gfx related */ u8 IgdDvmt50PreAlloc; u8 PrimaryDisplay; u8 InternalGfx; u8 ApertureSize; u8 SkipExtGfxScan; u8 ScanExtGfxForLegacyOpRom; /* * The following fields come from fsp_vpd.h * These are configuration values that are passed to FSP during * SiliconInit. */ u32 LogoPtr; u32 LogoSize; u32 GraphicsConfigPtr; u8 Device4Enable; u8 RtcLock; /* GPIO IRQ Route The valid values is 14 or 15*/ u8 GpioIrqSelect; /* SCI IRQ Select The valid values is 9, 10, 11 and 20 21, 22, 23*/ u8 SciIrqSelect; /* TCO IRQ Select The valid values is 9, 10, 11, 20 21, 22, 23*/ u8 TcoIrqSelect; u8 TcoIrqEnable; /* Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.*/ u8 LockDownConfigGlobalSmi; /* * Enable BIOS Interface Lock Down bit to prevent writes to the Backup * Control Register. Top Swap bit and the General Control and Status * Registers Boot BIOS Straps. */ u8 LockDownConfigBiosInterface; /* * Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh * in the upper and and lower 128-byte bank of RTC RAM. */ u8 LockDownConfigRtcLock; /* * When enabled, the BIOS Region can only be modified from SMM after * EndOfDxe protocol is installed */ u8 LockDownConfigBiosLock; /* * Enable InSMM.STS (EISS) in SPI If this bit is set, then WPD must be a * '1' and InSMM.STS must be '1' also in order to write to BIOS regions of * SPI Flash. If this bit is clear, then the InSMM.STS is a don't care. The * BIOS must set the EISS bit while BIOS Guard support is enabled. */ u8 LockDownConfigSpiEiss; /* Subsystem Vendor ID of the PCH devices*/ u16 PchConfigSubSystemVendorId; /* Subsystem ID of the PCH devices*/ u16 PchConfigSubSystemId; /* * Corresponds to the "WOL Enable Override" bit in the General PM * Configuration B (GEN_PMCON_B) register */ u8 WakeConfigWolEnableOverride; /* Determine if enable PCIe to wake from deep Sx*/ u8 WakeConfigPcieWakeFromDeepSx; /* Deep Sx Policy. Values 0: PchDeepSxPolDisable, * 1: PchDpS5BatteryEn, 2: PchDpS5AlwaysEn, 3: PchDpS4S5BatteryEn, * 4: PchDpS4S5AlwaysEn, 5: PchDpS3S4S5BatteryEn, 6: PchDpS3S4S5AlwaysEn */ u8 PmConfigDeepSxPol; /* * SLP_S3 Minimum Assertion Width Policy. Values 0: PchSlpS360us, * 1: PchSlpS31ms, 2: PchSlpS350ms, 3: PchSlpS32s. */ u8 PmConfigSlpS3MinAssert; /* * SLP_S4 Minimum Assertion Width Policy. Values 0: PchSlpS4PchTime, * 1: PchSlpS41s, 2: PchSlpS42s, 3: PchSlpS43s, 4: PchSlpS44s. */ u8 PmConfigSlpS4MinAssert; /* * SLP_SUS Minimum Assertion Width Policy. Values 0: PchSlpSus0ms, * 1: PchSlpSus500ms, 2: PchSlpSus1s, 3: PchSlpSus4s. */ u8 PmConfigSlpSusMinAssert; /* * SLP_A Minimum Assertion Width Policy. Values 0: PchSlpA0ms, * 1: PchSlpA4s, 2: PchSlpA98ms, 3: PchSlpA2s. */ u8 PmConfigSlpAMinAssert; /* * This member describes whether or not the PCI ClockRun feature of PCH * should be enabled. Values 0: Disabled, 1: Enabled */ u8 PmConfigPciClockRun; /* * SLP_X Stretching After SUS Well Power Up. Values 0: Disabled, 1: Enabled */ u8 PmConfigSlpStrchSusUp; /* * PCH power button override period. * Values: 0x0 - 4s, 0x1 - 6s, 0x2 - 8s, 0x3 - 10s, 0x4 - 12s, 0x5 - 14s */ u8 PmConfigPwrBtnOverridePeriod; /* * Reset Power Cycle Duration could be customized in the unit of second. * PCH HW default is 4 seconds, and range is 1~4 seconds. * Values: 0x0 - 0s, 0x1 - 1s, 0x2 - 2s, 0x3 - 3s, 0x4 - 4s */ u8 PmConfigPwrCycDur; /* Determines if enable Serial IRQ. Values 0: Disabled, 1: Enabled.*/ u8 SerialIrqConfigSirqEnable; /* Serial IRQ Mode Select. Values: 0: PchQuietMode, 1: PchContinuousMode.*/ u8 SerialIrqConfigSirqMode; /* * Start Frame Pulse Width. * Values: 0: PchSfpw4Clk, 1: PchSfpw6Clk, 2; PchSfpw8Clk. */ u8 SerialIrqConfigStartFramePulse; u8 FspSkipMpInit; /* * VrConfig Settings for 5 domains * 0 = System Agent, 1 = IA Core, 2 = Ring, * 3 = GT unsliced, 4 = GT sliced */ struct vr_config domain_vr_config[NUM_VR_DOMAINS]; /* * HeciEnabled decides the state of Heci1 at end of boot * Setting to 0 (default) disables Heci1 and hides the device from OS */ u8 HeciEnabled; /* PL2 Override value in Watts */ u32 tdp_pl2_override; u8 PmTimerDisabled; /* Intel Speed Shift Technology */ u8 speed_shift_enable; /* * Enable VR specific mailbox command * 000b - Don't Send any VR command * 001b - VR command specifically for the MPS IMPV8 VR will be sent * 010b - VR specific command sent for PS4 exit issue * 011b - VR specific command sent for both MPS IMPV8 & PS4 exit issue */ u8 SendVrMbxCmd; /* Statically clock gate 8254 PIT. */ u8 clock_gate_8254; /* * Use SD card detect GPIO with default config: * - Edge triggered * - No internal pull * - Active both (high + low) * - Can wake device from D3 * - 100ms debounce timeout * * GpioInt (Edge, ActiveBoth, SharedAndWake, PullNone, 10000, * "\\_SB.PCI0.GPIO", 0, ResourceConsumer) * { sdcard_cd_gpio_default } */ unsigned sdcard_cd_gpio_default; /* Use custom SD card detect GPIO configuration */ struct acpi_gpio sdcard_cd_gpio; }; typedef struct soc_intel_skylake_config config_t; extern struct chip_operations soc_ops; #endif