config SOC_INTEL_SKYLAKE bool help Intel Skylake support config SOC_INTEL_KABYLAKE bool default n select SOC_INTEL_SKYLAKE help Intel Kabylake support if SOC_INTEL_SKYLAKE config CPU_SPECIFIC_OPTIONS def_bool y select ACPI_INTEL_HARDWARE_SLEEP_VALUES select ARCH_BOOTBLOCK_X86_32 select ARCH_RAMSTAGE_X86_32 select ARCH_ROMSTAGE_X86_32 select ARCH_VERSTAGE_X86_32 select ACPI_NHLT select BOOTBLOCK_CONSOLE select BOOT_DEVICE_SPI_FLASH_RW_NOMMAP_EARLY if BOOT_DEVICE_SPI_FLASH select BOOT_DEVICE_SUPPORTS_WRITES select CACHE_MRC_SETTINGS select CACHE_RELOCATED_RAMSTAGE_OUTSIDE_CBMEM if RELOCATABLE_RAMSTAGE select C_ENVIRONMENT_BOOTBLOCK select COLLECT_TIMESTAMPS select COMMON_FADT select CPU_INTEL_FIRMWARE_INTERFACE_TABLE select GENERIC_GPIO_LIB select HAVE_HARD_RESET select HAVE_INTEL_FIRMWARE select HAVE_MONOTONIC_TIMER select HAVE_SMI_HANDLER select IOAPIC select NO_FIXED_XIP_ROM_SIZE select MRC_SETTINGS_PROTECT select PARALLEL_MP select PCIEXP_ASPM select PCIEXP_COMMON_CLOCK select PCIEXP_CLK_PM select PCIEXP_L1_SUB_STATE select REG_SCRIPT select RELOCATABLE_MODULES select RELOCATABLE_RAMSTAGE select RTC select SOC_INTEL_COMMON select SOC_INTEL_COMMON_ACPI_WAKE_SOURCE select SOC_INTEL_COMMON_BLOCK select SOC_INTEL_COMMON_BLOCK_XHCI select SOC_INTEL_COMMON_LPSS_I2C select SOC_INTEL_COMMON_NHLT select SOC_INTEL_COMMON_RESET select SOC_INTEL_COMMON_SPI_FLASH_PROTECT select SMM_TSEG select SMP select SSE2 select SUPPORT_CPU_UCODE_IN_CBFS select TSC_CONSTANT_RATE select TSC_SYNC_MFENCE select UDELAY_TSC select ACPI_NHLT config MAINBOARD_USES_FSP2_0 bool default n config USE_FSP2_0_DRIVER bool "Build with FSP 2.0" depends on MAINBOARD_USES_FSP2_0 default y if MAINBOARD_USES_FSP2_0 select PLATFORM_USES_FSP2_0 select ADD_VBT_DATA_FILE select SOC_INTEL_COMMON_GFX_OPREGION config USE_FSP1_1_DRIVER bool "Build with FSP 1.1" depends on !MAINBOARD_USES_FSP2_0 default y if !MAINBOARD_USES_FSP2_0 select PLATFORM_USES_FSP1_1 select GOP_SUPPORT select DISPLAY_FSP_ENTRY_POINTS config CHROMEOS select CHROMEOS_RAMOOPS_DYNAMIC select EC_SOFTWARE_SYNC if EC_GOOGLE_CHROMEEC select SEPARATE_VERSTAGE select VBOOT_EC_SLOW_UPDATE if EC_GOOGLE_CHROMEEC select VBOOT_OPROM_MATTERS select VBOOT_SAVE_RECOVERY_REASON_ON_REBOOT select VBOOT_STARTS_IN_BOOTBLOCK select VBOOT_VBNV_CMOS select VBOOT_VBNV_CMOS_BACKUP_TO_FLASH select VIRTUAL_DEV_SWITCH config BOOTBLOCK_RESETS string default "soc/intel/common/reset.c" config CBFS_SIZE hex default 0x200000 config CPU_ADDR_BITS int default 36 config SOC_INTEL_COMMON_LPSS_I2C_CLOCK_MHZ int default 120 config DCACHE_RAM_BASE hex "Base address of cache-as-RAM" default 0xfef00000 config DCACHE_RAM_SIZE hex "Length in bytes of cache-as-RAM" default 0x40000 help The size of the cache-as-ram region required during bootblock and/or romstage. config DCACHE_BSP_STACK_SIZE hex default 0x4000 help The amount of anticipated stack usage in CAR by bootblock and other stages. config C_ENV_BOOTBLOCK_SIZE hex default 0xC000 config EXCLUDE_NATIVE_SD_INTERFACE bool default n help If you set this option to n, will not use native SD controller. config HEAP_SIZE hex default 0x80000 config IED_REGION_SIZE hex default 0x400000 config MMCONF_BASE_ADDRESS hex "MMIO Base Address" default 0xe0000000 config MONOTONIC_TIMER_MSR def_bool y select HAVE_MONOTONIC_TIMER help Provide a monotonic timer using the 24MHz MSR counter. config PRE_GRAPHICS_DELAY int "Graphics initialization delay in ms" default 0 help On some systems, coreboot boots so fast that connected monitors (mostly TVs) won't be able to wake up fast enough to talk to the VBIOS. On those systems we need to wait for a bit before executing the VBIOS. config SERIAL_CPU_INIT bool default n config SERIRQ_CONTINUOUS_MODE bool default n help If you set this option to y, the serial IRQ machine will be operated in continuous mode. config SMM_RESERVED_SIZE hex default 0x200000 config SMM_TSEG_SIZE hex default 0x800000 config VGA_BIOS_ID string default "8086,0406" config UART_DEBUG bool "Enable UART debug port." default n select CONSOLE_SERIAL select DRIVERS_UART select DRIVERS_UART_8250MEM_32 select NO_UART_ON_SUPERIO config SKYLAKE_SOC_PCH_H bool default n help Choose this option if you have a PCH-H chipset. config CHIPSET_BOOTBLOCK_INCLUDE string default "soc/intel/skylake/bootblock/timestamp.inc" config NHLT_DMIC_2CH bool default n help Include DSP firmware settings for 2 channel DMIC array. config NHLT_DMIC_4CH bool default n help Include DSP firmware settings for 4 channel DMIC array. config NHLT_NAU88L25 bool default n help Include DSP firmware settings for nau88l25 headset codec. config NHLT_MAX98357 bool default n help Include DSP firmware settings for max98357 amplifier. config NHLT_SSM4567 bool default n help Include DSP firmware settings for ssm4567 smart amplifier. config NHLT_RT5663 bool default n help Include DSP firmware settings for rt5663 headset codec. config NHLT_MAX98927 bool default n help Include DSP firmware settings for max98927 amplifier. config SKIP_FSP_CAR bool "Skip cache as RAM setup in FSP" default y help Skip Cache as RAM setup in FSP. config SPI_FLASH_INCLUDE_ALL_DRIVERS bool default n config MAX_ROOT_PORTS int default 24 if PLATFORM_USES_FSP2_0 default 20 if PLATFORM_USES_FSP1_1 config NO_FADT_8042 bool default n help Choose this option if you want to disable 8042 Keyboard endif