config SOC_INTEL_JASPERLAKE bool help Intel Jasperlake support if SOC_INTEL_JASPERLAKE config CPU_SPECIFIC_OPTIONS def_bool y select ACPI_INTEL_HARDWARE_SLEEP_VALUES select ARCH_X86 select BOOT_DEVICE_SUPPORTS_WRITES select CACHE_MRC_SETTINGS select CPU_INTEL_COMMON select CPU_INTEL_FIRMWARE_INTERFACE_TABLE select CPU_SUPPORTS_PM_TIMER_EMULATION select COS_MAPPED_TO_MSB select FSP_COMPRESS_FSP_S_LZ4 select FSP_M_XIP select FSP_STATUS_GLOBAL_RESET_REQUIRED_3 select GENERIC_GPIO_LIB select HAVE_FSP_GOP select INTEL_DESCRIPTOR_MODE_CAPABLE select HAVE_SMI_HANDLER select IDT_IN_EVERY_STAGE select INTEL_CAR_NEM_ENHANCED select INTEL_GMA_ACPI select INTEL_GMA_ADD_VBT if RUN_FSP_GOP select IOAPIC select MP_SERVICES_PPI_V1 select MRC_SETTINGS_PROTECT select PARALLEL_MP_AP_WORK select MICROCODE_BLOB_UNDISCLOSED select PLATFORM_USES_FSP2_2 select REG_SCRIPT select PMC_GLOBAL_RESET_ENABLE_LOCK select PMC_LOW_POWER_MODE_PROGRAM select SOC_INTEL_COMMON select SOC_INTEL_COMMON_ACPI_WAKE_SOURCE select SOC_INTEL_COMMON_BLOCK select SOC_INTEL_COMMON_BLOCK_ACPI select SOC_INTEL_COMMON_BLOCK_ACPI_GPIO select SOC_INTEL_COMMON_BLOCK_ACPI_LPIT select SOC_INTEL_COMMON_BLOCK_CAR select SOC_INTEL_COMMON_BLOCK_CHIP_CONFIG select SOC_INTEL_COMMON_BLOCK_CNVI select SOC_INTEL_COMMON_BLOCK_CPU select SOC_INTEL_COMMON_BLOCK_CPU_MPINIT select SOC_INTEL_COMMON_BLOCK_CPU_SMMRELOCATE select SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT select SOC_INTEL_COMMON_BLOCK_GSPI_VERSION_2 select SOC_INTEL_COMMON_BLOCK_HDA select SOC_INTEL_COMMON_BLOCK_SA select SOC_INTEL_COMMON_BLOCK_SCS select SOC_INTEL_COMMON_BLOCK_SMM select SOC_INTEL_COMMON_BLOCK_POWER_LIMIT select SOC_INTEL_COMMON_BLOCK_SMM_IO_TRAP select SOC_INTEL_COMMON_BLOCK_XHCI_ELOG select SOC_INTEL_COMMON_FSP_RESET select SOC_INTEL_COMMON_PCH_BASE select SOC_INTEL_COMMON_RESET select SOC_INTEL_CSE_SET_EOP select SSE2 select SUPPORT_CPU_UCODE_IN_CBFS select TSC_MONOTONIC_TIMER select UDELAY_TSC select UDK_202005_BINDING select DISPLAY_FSP_VERSION_INFO_2 select HECI_DISABLE_USING_SMM config DCACHE_RAM_BASE default 0xfef00000 config DCACHE_RAM_SIZE default 0x80000 help The size of the cache-as-ram region required during bootblock and/or romstage. config DCACHE_BSP_STACK_SIZE hex default 0x30400 help The amount of anticipated stack usage in CAR by bootblock and other stages. In the case of FSP_USES_CB_STACK default value will be sum of FSP-M stack requirement(192 KiB) and CB romstage stack requirement(~1KiB). config FSP_TEMP_RAM_SIZE hex default 0x20000 help The amount of anticipated heap usage in CAR by FSP. Refer to Platform FSP integration guide document to know the exact FSP requirement for Heap setup. config IFD_CHIPSET string default "jsl" config IED_REGION_SIZE hex default 0x400000 config HEAP_SIZE hex default 0x8000 config MAX_ROOT_PORTS int default 8 config MAX_PCIE_CLOCK_SRC int default 6 config SMM_TSEG_SIZE hex default 0x800000 config SMM_RESERVED_SIZE hex default 0x200000 config PCR_BASE_ADDRESS hex default 0xfd000000 help This option allows you to select MMIO Base Address of sideband bus. config MMCONF_BASE_ADDRESS default 0xc0000000 config CPU_BCLK_MHZ int default 100 config SOC_INTEL_COMMON_BLOCK_GSPI_CLOCK_MHZ int default 120 config DRIVERS_I2C_DESIGNWARE_CLOCK_MHZ int default 133 config CPU_XTAL_HZ default 38400000 config SOC_INTEL_COMMON_BLOCK_GSPI_MAX int default 3 config SOC_INTEL_I2C_DEV_MAX int default 6 config SOC_INTEL_UART_DEV_MAX int default 3 config CONSOLE_UART_BASE_ADDRESS hex default 0xfe032000 depends on INTEL_LPSS_UART_FOR_CONSOLE # Clock divider parameters for 115200 baud rate # Baudrate = (UART source clcok * M) /(N *16) # JSL UART source clock: 100MHz config SOC_INTEL_COMMON_LPSS_UART_CLK_M_VAL hex default 0x30 config SOC_INTEL_COMMON_LPSS_UART_CLK_N_VAL hex default 0xc35 config VBOOT select VBOOT_SEPARATE_VERSTAGE select VBOOT_MUST_REQUEST_DISPLAY select VBOOT_STARTS_IN_BOOTBLOCK select VBOOT_VBNV_CMOS select VBOOT_VBNV_CMOS_BACKUP_TO_FLASH config CBFS_SIZE hex default 0x200000 config FSP_HEADER_PATH default "src/vendorcode/intel/fsp/fsp2_0/jasperlake/" config FSP_FD_PATH default "3rdparty/fsp/JasperLakeFspBinPkg/Fsp.fd" config SOC_INTEL_JASPERLAKE_DEBUG_CONSENT int "Debug Consent for JSL" # USB DBC is more common for developers so make this default to 3 if # SOC_INTEL_DEBUG_CONSENT=y default 3 if SOC_INTEL_DEBUG_CONSENT default 0 help This is to control debug interface on SOC. Setting non-zero value will allow to use DBC or DCI to debug SOC. PlatformDebugConsent in FspmUpd.h has the details. Desired platform debug type are 0:Disabled, 1:Enabled (DCI OOB+[DbC]), 2:Enabled (DCI OOB), 3:Enabled (USB3 DbC), 4:Enabled (XDP/MIPI60), 5:Enabled (USB2 DbC), 6:Enable (2-wire DCI OOB), 7:Manual config PRERAM_CBMEM_CONSOLE_SIZE hex default 0x1400 endif