## SPDX-License-Identifier: GPL-2.0-only config DISABLE_HECI1_AT_PRE_BOOT bool "Disable HECI1 at the end of boot" depends on SOC_INTEL_COMMON_BLOCK_CSE default n help This config decides the state of HECI1(CSE) device at the end of boot. Mainboard users to select this config to make HECI1 `function disable` prior to handing off to payload. config MAX_HECI_DEVICES int default 6 config SOC_INTEL_COMMON_BLOCK_CSE bool default n help Driver for communication with Converged Security Engine (CSE) over Host Embedded Controller Interface (HECI) config SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_SBI bool default y if HECI_DISABLE_USING_SMM select SOC_INTEL_COMMON_BLOCK_P2SB help Use this config to allow common CSE block to make HECI1 function disable in the SMM mode. From CNL PCH onwards,`HECI1` disabling can only be done using the non-posted sideband write after FSP-S sets the postboot_sai attribute. config SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_PMC_IPC bool default n select SOC_INTEL_COMMON_BLOCK_PMC help Use this config to allow common CSE block to make HECI1 function disable using PMC IPC command `0xA9`. From TGL PCH onwards, disabling heci1 device using PMC IPC doesn't required to run the operation in SMM. config SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_PCR bool default n select SOC_INTEL_COMMON_BLOCK_PCR help Use this config for SoC platform prior to CNL PCH (with postboot_sai implemented) to make `HECI1` device disable using private configuration register (PCR) write. config SOC_INTEL_STORE_CSE_FW_VERSION bool default y depends on SOC_INTEL_CSE_LITE_SKU help This configuration option stores CSE RW FW version in CBMEM area. This information can be used to identify if the CSE firmware update is successful by comparing the currently running CSE RW firmware version against CSE version belongs to the CONFIG_SOC_INTEL_CSE_RW_VERSION (decided statically while building the AP FW image). The way to retrieve the CSE firmware version is by sending the HECI command to read the CSE Boot Partition (BP) info. The cost of sending HECI command to read the CSE FW version is between 7ms-20ms (depending on the SoC architecture) hence, ensure this feature is platform specific and only enabled for the platform that would like to store the CSE version into the CBMEM. config SOC_INTEL_CSE_FW_PARTITION_CMOS_OFFSET int default 68 depends on SOC_INTEL_CSE_LITE_SKU help This configuration option stores the starting offset of cse fw partition versions in CMOS memory. The offset should be byte aligned and must leave enough memory to store required firmware partition versions. config SOC_INTEL_STORE_ISH_FW_VERSION bool default n depends on DRIVERS_INTEL_ISH help This configuration option stores ISH version in CBMEM area. This information can be used to identify the currently running ISH firmware version. ISH BUP is sitting inside the CSE firmware partition. The way to retrieve the ISH version is by sending the HECI command to read the CSE FPT. The cost of sending HECI command to read the CSE FPT is significant (~200ms) hence, the idea is to read the CSE RW version on every cold reset (to cover the CSE update scenarios) and store into CBMEM to avoid the cost of resending the HECI command in all consecutive warm boots. Later boot stages can just read the CBMEM ID to retrieve the ISH version. Additionally, ensure this feature is platform specific hence, only enabled for the platform that would like to store the ISH version into the CBMEM and parse to perform some additional work. config SOC_INTEL_CSE_SEND_EOP_EARLY bool "CSE send EOP early" depends on SOC_INTEL_COMMON_BLOCK_CSE && !SOC_INTEL_CSE_SEND_EOP_BY_PAYLOAD help Use this config to send End Of Post (EOP) earlier through SoC code in order to reduce time required to send EOP and getting CSE response. In later stages, CSE might be busy and might require more time to process EOP command. SoC can use this Kconfig to send EOP earlier by itself. config SOC_INTEL_CSE_SEND_EOP_LATE bool depends on SOC_INTEL_COMMON_BLOCK_CSE && !SOC_INTEL_CSE_SEND_EOP_BY_PAYLOAD help Use this config to send End Of Post (EOP) late (even after CSE `final` operation) using boot state either `BS_PAYLOAD_BOOT` or `BS_PAYLOAD_LOAD` from common code in order to reduce time required to send EOP and getting CSE response. It has been observed that CSE might be busy and might require more time to process the EOP command. SoC can use this Kconfig to send EOP later by itself. Starting with Jasper Lake, coreboot sends EOP before loading payload hence, this config is applicable for those platforms. config SOC_INTEL_CSE_SEND_EOP_ASYNC bool depends on SOC_INTEL_COMMON_BLOCK_CSE && !SOC_INTEL_CSE_SEND_EOP_BY_PAYLOAD depends on !SOC_INTEL_CSE_SEND_EOP_LATE depends on !SOC_INTEL_CSE_SEND_EOP_EARLY help Use this config to handle End Of Post (EOP) completion asynchronously. The EOP command is sent first and the result is checked later leaving time to CSE to complete the operation while coreboot perform other activities. Performing EOP asynchronously reduces the time spent actively waiting for command completion which can have a significant impact on boot time. Using this asynchronous approach comes with the limitation that no HECI command should be sent between the time the EOP request is posted (at CSE .final device operation) and the time coreboot check for its completion (BS_PAYLOAD_LOAD). config SOC_INTEL_CSE_SEND_EOP_BY_PAYLOAD bool depends on SOC_INTEL_COMMON_BLOCK_CSE help Use this config to specify that the payload will send the End Of Post (EOP) instead of coreboot. In this case, the HECI interface needs to stay visible and the payload must support sending commands to CSE. config SOC_INTEL_CSE_LITE_SYNC_BY_PAYLOAD bool depends on SOC_INTEL_COMMON_BLOCK_CSE help Use this config to specify that the payload will update the CSE RW partition instead of coreboot. In this case, CSE shall not switch to RW partition and the payload must support CSE RW update. config SOC_INTEL_CSE_LITE_SKU bool default n help Enables CSE Lite SKU config SOC_INTEL_CSE_LITE_PSR bool default n depends on SOC_INTEL_CSE_LITE_SKU && !SOC_INTEL_CSE_LITE_SYNC_BY_PAYLOAD select SOC_INTEL_CSE_LITE_SYNC_IN_RAMSTAGE help Select this config if Platform Service Record(PSR) is supported by the platform. This config is applicable only for Lite SKU, where PSR data backup is required prior to a CSE firmware downgrade during which CSE data is cleared. PSR services in CSE FW is enabled only post DRAM init and the command to backup PSR data is also supported only post DRAM init. Hence platform that selects PSR would need to perform CSE firmware sync in ramstage. config SOC_INTEL_CSE_SERVER_SKU bool default n help Enables CSE Server SKU config SOC_INTEL_CSE_RW_UPDATE bool "Enable the CSE RW Update Feature" default n depends on SOC_INTEL_CSE_LITE_SKU help This config will enable CSE RW firmware update feature and also will be used ensure all the required configs are provided by mainboard. config SOC_INTEL_CSE_FMAP_NAME string "Name of CSE Region in FMAP" if SOC_INTEL_CSE_RW_UPDATE default "SI_ME" help Name of CSE region in FMAP config SOC_INTEL_CSE_RW_A_FMAP_NAME string "Location of CSE RW A in FMAP" if SOC_INTEL_CSE_RW_UPDATE default "ME_RW_A" help Name of CSE RW A region in FMAP config SOC_INTEL_CSE_RW_B_FMAP_NAME string "Location of CSE RW B in FMAP" if SOC_INTEL_CSE_RW_UPDATE default "ME_RW_B" help Name of CSE RW B region in FMAP config SOC_INTEL_CSE_RW_CBFS_NAME string "CBFS entry name for CSE RW blob" if SOC_INTEL_CSE_RW_UPDATE default "me_rw" help CBFS entry name for Intel CSE CBFS RW blob config SOC_INTEL_CSE_RW_HASH_CBFS_NAME string "CBFS name for CSE RW hash file" if SOC_INTEL_CSE_RW_UPDATE default "me_rw.hash" help CBFS name for Intel CSE CBFS RW hash file config SOC_INTEL_CSE_RW_VERSION_CBFS_NAME string "CBFS name for CSE RW version file" if SOC_INTEL_CSE_RW_UPDATE default "me_rw.version" help CBFS name for Intel CSE CBFS RW version file config SOC_INTEL_CSE_RW_FILE string "Intel CSE CBFS RW path and filename" if SOC_INTEL_CSE_RW_UPDATE && !STITCH_ME_BIN default "" help Intel CSE CBFS RW blob path and file name config SOC_INTEL_CSE_RW_VERSION string "Intel CSE RW firmware version (deprecated)" if SOC_INTEL_CSE_RW_UPDATE default "" help This config contains the Intel CSE RW version of the blob that is provided by SOC_INTEL_CSE_RW_FILE config and the version must be set in the format major.minor.hotfix.build (ex: 14.0.40.1209). This config may be deprecated in the future. Consider not providing the CSE RW firmware version here and let the CSE version be automatically queried from the CSE binary at build time (available with Meteor Lake and following platforms). config SOC_INTEL_CSE_SET_EOP bool default n select PMC_IPC_ACPI_INTERFACE help This config ensures coreboot will send the CSE the End-of-POST message just prior to loading the payload. This is a security feature so the CSE will no longer respond to Pre-Boot commands. config SOC_INTEL_CSE_SUB_PART_UPDATE bool "Enable the CSE sub-partition update Feature" default n depends on SOC_INTEL_CSE_LITE_SKU help This config will enable CSE sub-partition firmware update feature and also will be used ensure all the required configs are provided by mainboard. config SOC_INTEL_CSE_IOM_CBFS_NAME string "CBFS name for CSE sub-partition IOM binary" if SOC_INTEL_CSE_SUB_PART_UPDATE default "cse_iom" help CBFS entry name for Intel CSE sub-partition IOM binary config SOC_INTEL_CSE_IOM_CBFS_FILE string "Intel CBFS path and file name for CSE sub-partition IOM binary" if SOC_INTEL_CSE_SUB_PART_UPDATE default "" help CBFS path and file name for Intel CSE sub-partition IOM binary config SOC_INTEL_CSE_NPHY_CBFS_NAME string "CBFS name for CSE sub-partition NPHY binary" if SOC_INTEL_CSE_SUB_PART_UPDATE default "cse_nphy" help CBFS entry name for Intel CSE sub-partition NPHY binary config SOC_INTEL_CSE_NPHY_CBFS_FILE string "Intel CBFS path and file name for CSE sub-partition NPHY binary" if SOC_INTEL_CSE_SUB_PART_UPDATE default "" help CBFS path and file name for Intel CSE sub-partition NPHY binary config SOC_INTEL_CSE_LITE_COMPRESS_ME_RW bool default n depends on SOC_INTEL_CSE_LITE_SKU select CBFS_ALLOW_UNVERIFIED_DECOMPRESSION if CBFS_VERIFICATION && !VBOOT_CBFS_INTEGRATION help Enable compression on Intel CSE CBFS RW blob config SOC_INTEL_CSE_PRE_CPU_RESET_TELEMETRY def_bool n depends on SOC_INTEL_CSE_LITE_SKU && !SOC_INTEL_CSE_LITE_SYNC_BY_PAYLOAD help Mainboard user to select this Kconfig in order to capture pre-cpu reset boot performance telemetry data. config SOC_INTEL_CSE_PRE_CPU_RESET_TELEMETRY_V1 bool select SOC_INTEL_CSE_PRE_CPU_RESET_TELEMETRY help This config will make mainboard use version 1 of the CSE timestamp definitions, it can be used for Alder Lake and Raptor Lake (all SKUs). config SOC_INTEL_CSE_PRE_CPU_RESET_TELEMETRY_V2 bool select SOC_INTEL_CSE_PRE_CPU_RESET_TELEMETRY help This config will make mainboard use version 2 of the CSE timestamp definitions, it can be used for Meteor Lake M/P. config SOC_INTEL_CSE_LITE_SYNC_IN_ROMSTAGE bool default !SOC_INTEL_CSE_LITE_SYNC_IN_RAMSTAGE depends on SOC_INTEL_CSE_LITE_SKU && !SOC_INTEL_CSE_LITE_COMPRESS_ME_RW && !SOC_INTEL_CSE_LITE_SYNC_BY_PAYLOAD help Use default flow of CSE FW Update in romstage when uncompressed ME_RW blobs are used. config SOC_INTEL_CSE_LITE_SYNC_IN_RAMSTAGE bool default n depends on !SOC_INTEL_CSE_LITE_SYNC_BY_PAYLOAD help Use this option if CSE RW update needs to be triggered during RAMSTAGE. config SOC_INTEL_CSE_HAVE_SPEC_SUPPORT bool depends on SOC_INTEL_COMMON_BLOCK_CSE default n help This option config will allow SoC platform to use applicable ME specification. The version based CSE measured ME specification data structures are defined at common code. Enabling this option will use those CSE defined ME specification for the SoC. User should select pertinent ME spec version along with this option. config SOC_INTEL_COMMON_BLOCK_ME_SPEC_12 bool select SOC_INTEL_CSE_HAVE_SPEC_SUPPORT help This config will enable 'ME specification version 12'. It will ensure ME specific declaration and uses of required data structures for Host firmware status registers. config SOC_INTEL_COMMON_BLOCK_ME_SPEC_13 bool select SOC_INTEL_CSE_HAVE_SPEC_SUPPORT help This config will enable 'ME specification version 13'. It will ensure ME specific declaration and uses of required data structures for Host firmware status registers. config SOC_INTEL_COMMON_BLOCK_ME_SPEC_15 bool select SOC_INTEL_CSE_HAVE_SPEC_SUPPORT help This config will enable 'ME specification version 15'. It will ensure ME specific declaration and uses of required data structures for Host firmware status registers. config SOC_INTEL_COMMON_BLOCK_ME_SPEC_16 bool select SOC_INTEL_CSE_HAVE_SPEC_SUPPORT help This config will enable 'ME specification version 16'. It will ensure ME specific declaration and uses of required data structures for Host firmware status registers. config SOC_INTEL_COMMON_BLOCK_ME_SPEC_18 bool select SOC_INTEL_CSE_HAVE_SPEC_SUPPORT help This config will enable 'ME specification version 18'. It will ensure ME specific declaration and uses of required data structures for Host firmware status registers. if SOC_INTEL_CSE_HAVE_SPEC_SUPPORT config ME_SPEC int default 12 if SOC_INTEL_COMMON_BLOCK_ME_SPEC_12 default 13 if SOC_INTEL_COMMON_BLOCK_ME_SPEC_13 default 15 if SOC_INTEL_COMMON_BLOCK_ME_SPEC_15 default 16 if SOC_INTEL_COMMON_BLOCK_ME_SPEC_16 default 18 if SOC_INTEL_COMMON_BLOCK_ME_SPEC_18 help This config holds the ME spec version if defined. endif # SOC_INTEL_CSE_HAVE_SPEC_SUPPORT if STITCH_ME_BIN config CSE_COMPONENTS_PATH string "Path to directory containing all CSE input components to stitch" default "3rdparty/blobs/mainboard/\$(CONFIG_MAINBOARD_DIR)/firmware" help This is the file path containing all the input CSE component files. These will be used by cse_serger tool to stitch CSE image. config CSE_FPT_FILE string "Name of CSE FPT file" default "cse_fpt.bin" help This file is the CSE input binary as released by Intel in a CSE kit. config CSE_DATA_FILE string "Name of CSE data file" default "cse_data.bin" help This file is the CSE data binary typically generated by Intel FIT tool. config CSE_PMCP_FILE string "Name of PMC file" default "pmc.bin" help This file is the PMC input binary as released by Intel in a CSE kit. config CSE_IOMP_FILE string "Name of IOM file" default "iom.bin" help This file is the IOM input binary as released by Intel in a CSE kit. config CSE_TBTP_FILE string "Name of TBT file" default "tbt.bin" help This file is the TBT input binary as released by Intel in a CSE kit. config CSE_NPHY_FILE string "Name of NPHY file" default "nphy.bin" help This file is the NPHY input binary as released by Intel in a CSE kit. config CSE_PCHC_FILE string "Name of PCHC file" default "pchc.bin" help This file is the PCHC input binary as released by Intel in a CSE kit. config CSE_IUNP_FILE string "Name of IUNIT file" default "iunit.bin" help This file is the PCHC input binary as released by Intel in a CSE kit. config CSE_BPDT_VERSION string help This config indicates the BPDT version used by CSE for a given SoC. config CSE_OEMP_FILE string "Name of OEM Key Manifest file" default "oem_km.bin" help OEM Key Manifest lists the public key hashes used for authenticating the OEM created binaries to be loaded. This binary is generated by signing with the key owned by trusted owner. endif config CSE_RESET_CLEAR_EC_AP_IDLE_FLAG bool default y if !SYSTEM_TYPE_LAPTOP help Select this if the variant is a Chromebox/base. This allows AP to direct EC to clear AP_IDLE flag before triggering reset to make sure AP can boot up after reset.