# SPDX-License-Identifier: GPL-2.0-only config SOC_AMD_PICASSO bool help AMD Picasso support if SOC_AMD_PICASSO config CPU_SPECIFIC_OPTIONS def_bool y select ACPI_SOC_NVS select ADD_FSP_BINARIES if USE_AMD_BLOBS select ARCH_BOOTBLOCK_X86_32 select ARCH_VERSTAGE_X86_32 if !VBOOT_STARTS_BEFORE_BOOTBLOCK select ARCH_ROMSTAGE_X86_32 select ARCH_RAMSTAGE_X86_32 select ARCH_X86 select BOOT_DEVICE_SUPPORTS_WRITES if BOOT_DEVICE_SPI_FLASH select CONSOLE_CBMEM_PRINT_PRE_BOOTBLOCK_CONTENTS if VBOOT_STARTS_BEFORE_BOOTBLOCK select DRIVERS_USB_PCI_XHCI select FSP_COMPRESS_FSP_M_LZMA select FSP_COMPRESS_FSP_S_LZMA select GENERIC_GPIO_LIB select HAVE_ACPI_TABLES select HAVE_CF9_RESET select HAVE_EM100_SUPPORT select HAVE_SMI_HANDLER select IDT_IN_EVERY_STAGE select PARALLEL_MP_AP_WORK select PLATFORM_USES_FSP2_0 select PROVIDES_ROM_SHARING select RESET_VECTOR_IN_RAM select RTC select SOC_AMD_COMMON select SOC_AMD_COMMON_BLOCK_ACP_GEN1 select SOC_AMD_COMMON_BLOCK_ACPI select SOC_AMD_COMMON_BLOCK_ACPIMMIO select SOC_AMD_COMMON_BLOCK_ACPI_ALIB select SOC_AMD_COMMON_BLOCK_ACPI_GPIO select SOC_AMD_COMMON_BLOCK_ACPI_IVRS select SOC_AMD_COMMON_BLOCK_AOAC select SOC_AMD_COMMON_BLOCK_APOB select SOC_AMD_COMMON_BLOCK_BANKED_GPIOS select SOC_AMD_COMMON_BLOCK_DATA_FABRIC select SOC_AMD_COMMON_BLOCK_GRAPHICS select SOC_AMD_COMMON_BLOCK_HAS_ESPI select SOC_AMD_COMMON_BLOCK_HDA select SOC_AMD_COMMON_BLOCK_I2C select SOC_AMD_COMMON_BLOCK_I2C_PAD_CTRL select SOC_AMD_COMMON_BLOCK_IOMMU select SOC_AMD_COMMON_BLOCK_LPC select SOC_AMD_COMMON_BLOCK_MCAX select SOC_AMD_COMMON_BLOCK_NONCAR select SOC_AMD_COMMON_BLOCK_PCI select SOC_AMD_COMMON_BLOCK_PCIE_GPP_DRIVER select SOC_AMD_COMMON_BLOCK_PM select SOC_AMD_COMMON_BLOCK_PM_CHIPSET_STATE_SAVE select SOC_AMD_COMMON_BLOCK_PSP_GEN2 select SOC_AMD_COMMON_BLOCK_SATA select SOC_AMD_COMMON_BLOCK_SMBUS select SOC_AMD_COMMON_BLOCK_SMI select SOC_AMD_COMMON_BLOCK_SMM select SOC_AMD_COMMON_BLOCK_SMU select SOC_AMD_COMMON_BLOCK_SPI select SOC_AMD_COMMON_BLOCK_TSC_FAM17H_19H select SOC_AMD_COMMON_BLOCK_UART select SOC_AMD_COMMON_BLOCK_UCODE select SOC_AMD_COMMON_FSP_DMI_TABLES select SSE2 select UDK_2017_BINDING select USE_FSP_NOTIFY_PHASE_POST_PCI_ENUM select USE_FSP_NOTIFY_PHASE_READY_TO_BOOT select USE_FSP_NOTIFY_PHASE_END_OF_FIRMWARE select X86_AMD_FIXED_MTRRS select X86_INIT_NEED_1_SIPI config ARCH_ALL_STAGES_X86 default n config CHIPSET_DEVICETREE string default "soc/amd/picasso/chipset.cb" config FSP_M_FILE string "FSP-M (memory init) binary path and filename" depends on ADD_FSP_BINARIES default "3rdparty/amd_blobs/picasso/PICASSO_M.fd" help The path and filename of the FSP-M binary for this platform. config FSP_S_FILE string "FSP-S (silicon init) binary path and filename" depends on ADD_FSP_BINARIES default "3rdparty/amd_blobs/picasso/PICASSO_S.fd" help The path and filename of the FSP-S binary for this platform. config EARLY_RESERVED_DRAM_BASE hex default 0x2000000 help This variable defines the base address of the DRAM which is reserved for usage by coreboot in early stages (i.e. before ramstage is up). This memory gets reserved in BIOS tables to ensure that the OS does not use it, thus preventing corruption of OS memory in case of S3 resume. config EARLYRAM_BSP_STACK_SIZE hex default 0x1000 config PSP_APOB_DRAM_ADDRESS hex default 0x2001000 help Location in DRAM where the PSP will copy the AGESA PSP Output Block. config PSP_SHAREDMEM_BASE hex default 0x2011000 if VBOOT default 0x0 help This variable defines the base address in DRAM memory where PSP copies the vboot workbuf. This is used in the linker script to have a static allocation for the buffer as well as for adding relevant entries in the BIOS directory table for the PSP. config PSP_SHAREDMEM_SIZE hex default 0x8000 if VBOOT default 0x0 help Sets the maximum size for the PSP to pass the vboot workbuf and any logs or timestamps back to coreboot. This will be copied into main memory by the PSP and will be available when the x86 is started. The workbuf's base depends on the address of the reset vector. config PRE_X86_CBMEM_CONSOLE_SIZE hex default 0x1600 help Size of the CBMEM console used in PSP verstage. config PRERAM_CBMEM_CONSOLE_SIZE hex default 0x1600 help Increase this value if preram cbmem console is getting truncated config CBFS_MCACHE_SIZE hex default 0x2000 if VBOOT_STARTS_BEFORE_BOOTBLOCK config C_ENV_BOOTBLOCK_SIZE hex default 0x10000 help Sets the size of the bootblock stage that should be loaded in DRAM. This variable controls the DRAM allocation size in linker script for bootblock stage. config ROMSTAGE_ADDR hex default 0x2040000 help Sets the address in DRAM where romstage should be loaded. config ROMSTAGE_SIZE hex default 0x80000 help Sets the size of DRAM allocation for romstage in linker script. config FSP_M_ADDR hex default 0x20C0000 help Sets the address in DRAM where FSP-M should be loaded. cbfstool performs relocation of FSP-M to this address. config FSP_M_SIZE hex default 0xC0000 help Sets the size of DRAM allocation for FSP-M in linker script. config VERSTAGE_ADDR hex depends on VBOOT_SEPARATE_VERSTAGE default 0x2180000 help Sets the address in DRAM where verstage should be loaded if running as a separate stage on x86. config VERSTAGE_SIZE hex depends on VBOOT_SEPARATE_VERSTAGE default 0x80000 help Sets the size of DRAM allocation for verstage in linker script if running as a separate stage on x86. config ECAM_MMCONF_BASE_ADDRESS default 0xF8000000 config ECAM_MMCONF_BUS_NUMBER default 64 config VERSTAGE_ADDR hex default 0x4000000 config MAX_CPUS int default 8 help Maximum number of threads the platform can have. config VGA_BIOS_ID string default "1002,15d8,c1" help The default VGA BIOS PCI vendor/device ID should be set to the result of the map_oprom_vendev_rev() function in northbridge.c. config VGA_BIOS_FILE string default "3rdparty/amd_blobs/picasso/PicassoGenericVbios.bin" config VGA_BIOS_SECOND def_bool y config VGA_BIOS_SECOND_ID string default "1002,15dd,c4" help Because Dali and Picasso need different video BIOSes, but have the same vendor/device IDs, we need an alternate method to determine the correct video BIOS. In map_oprom_vendev_rev(), we look at the cpuid and decide which rom to load. Even though the hardware has the same vendor/device IDs, the vBIOS contains a *different* device ID, confusing the situation even more. config VGA_BIOS_SECOND_FILE string default "3rdparty/amd_blobs/picasso/Raven2GenericVbios.bin" config CHECK_REV_IN_OPROM_NAME bool default y help Select this in the platform BIOS or chipset if the option rom has a revision that needs to be checked when searching CBFS. config S3_VGA_ROM_RUN bool default n config HEAP_SIZE hex default 0xc0000 config SERIRQ_CONTINUOUS_MODE bool default n help Set this option to y for serial IRQ in continuous mode. Otherwise it is in quiet mode. config CONSOLE_UART_BASE_ADDRESS depends on CONSOLE_SERIAL && AMD_SOC_CONSOLE_UART hex default 0xfedc9000 if UART_FOR_CONSOLE = 0 default 0xfedca000 if UART_FOR_CONSOLE = 1 default 0xfedce000 if UART_FOR_CONSOLE = 2 default 0xfedcf000 if UART_FOR_CONSOLE = 3 config SMM_TSEG_SIZE hex default 0x800000 if HAVE_SMI_HANDLER default 0x0 config SMM_RESERVED_SIZE hex default 0x180000 config SMM_MODULE_STACK_SIZE hex default 0x800 config ACPI_CPU_STRING string default "\\_SB.C%03d" config ACPI_BERT bool "Build ACPI BERT Table" default y depends on HAVE_ACPI_TABLES help Report Machine Check errors identified in POST to the OS in an ACPI Boot Error Record Table. config ACPI_BERT_SIZE hex default 0x4000 if ACPI_BERT default 0x0 help Specify the amount of DRAM reserved for gathering the data used to generate the ACPI table. config ACPI_SSDT_PSD_INDEPENDENT bool "Allow core p-state independent transitions" default y help AMD recommends the ACPI _PSD object to be configured to cause cores to transition between p-states independently. A vendor may choose to generate _PSD object to allow cores to transition together. config CHROMEOS select ALWAYS_LOAD_OPROM select ALWAYS_RUN_OPROM config RO_REGION_ONLY string depends on CHROMEOS default "apu/amdfw" config DRIVERS_I2C_DESIGNWARE_CLOCK_MHZ int default 150 config DISABLE_SPI_FLASH_ROM_SHARING def_bool n help Instruct the chipset to not honor the EGPIO67_SPI_ROM_REQ pin which indicates a board level ROM transaction request. This removes arbitration with board and assumes the chipset controls the SPI flash bus entirely. config DISABLE_KEYBOARD_RESET_PIN bool help Instruct the SoC to not use the state of GPIO_129 as keyboard reset signal. When this pin is used as GPIO and the keyboard reset functionality isn't disabled, configuring it as an output and driving it as 0 will cause a reset. config FSP_TEMP_RAM_SIZE hex default 0x40000 help The amount of coreboot-allocated heap and stack usage by the FSP. menu "PSP Configuration Options" config AMD_FWM_POSITION_INDEX int "Firmware Directory Table location (0 to 5)" range 0 5 default 0 if BOARD_ROMSIZE_KB_512 default 1 if BOARD_ROMSIZE_KB_1024 default 2 if BOARD_ROMSIZE_KB_2048 default 3 if BOARD_ROMSIZE_KB_4096 default 4 if BOARD_ROMSIZE_KB_8192 default 5 if BOARD_ROMSIZE_KB_16384 help Typically this is calculated by the ROM size, but there may be situations where you want to put the firmware directory table in a different location. 0: 512 KB - 0xFFFA0000 1: 1 MB - 0xFFF20000 2: 2 MB - 0xFFE20000 3: 4 MB - 0xFFC20000 4: 8 MB - 0xFF820000 5: 16 MB - 0xFF020000 comment "AMD Firmware Directory Table set to location for 512KB ROM" depends on AMD_FWM_POSITION_INDEX = 0 comment "AMD Firmware Directory Table set to location for 1MB ROM" depends on AMD_FWM_POSITION_INDEX = 1 comment "AMD Firmware Directory Table set to location for 2MB ROM" depends on AMD_FWM_POSITION_INDEX = 2 comment "AMD Firmware Directory Table set to location for 4MB ROM" depends on AMD_FWM_POSITION_INDEX = 3 comment "AMD Firmware Directory Table set to location for 8MB ROM" depends on AMD_FWM_POSITION_INDEX = 4 comment "AMD Firmware Directory Table set to location for 16MB ROM" depends on AMD_FWM_POSITION_INDEX = 5 config AMDFW_CONFIG_FILE string default "src/soc/amd/picasso/fw.cfg" config PSP_LOAD_MP2_FW bool default n help Include the MP2 firmwares and configuration into the PSP build. If unsure, answer 'n' config PSP_LOAD_S0I3_FW bool default n help Select this item to include the S0i3 file into the PSP build. config HAVE_PSP_WHITELIST_FILE bool "Include a debug whitelist file in PSP build" default n help Support secured unlock prior to reset using a whitelisted number? This feature requires a signed whitelist image and bootloader from AMD. If unsure, answer 'n' config PSP_WHITELIST_FILE string "Debug whitelist file path" depends on HAVE_PSP_WHITELIST_FILE default "3rdparty/amd_blobs/picasso/PSP/wtl-rvn.sbin" config PSP_UNLOCK_SECURE_DEBUG bool "Unlock secure debug" default n help Select this item to enable secure debug options in PSP. config PSP_VERSTAGE_FILE string "Specify the PSP_verstage file path" depends on VBOOT_STARTS_BEFORE_BOOTBLOCK default "\$(obj)/psp_verstage.bin" help Add psp_verstage file to the build & PSP Directory Table config PSP_VERSTAGE_SIGNING_TOKEN string "Specify the PSP_verstage Signature Token file path" depends on VBOOT_STARTS_BEFORE_BOOTBLOCK default "" help Add psp_verstage signature token to the build & PSP Directory Table config PSP_SOFTFUSE_BITS string "PSP Soft Fuse bits to enable" default "28" help Space separated list of Soft Fuse bits to enable. Bit 0: Enable secure debug (Set by PSP_UNLOCK_SECURE_DEBUG) Bit 15: PSP post code destination: 0=LPC 1=eSPI Bit 29: Disable MP2 firmware loading (Set by PSP_LOAD_MP2_FW) See #55758 (NDA) for additional bit definitions. endmenu config VBOOT select VBOOT_VBNV_CMOS select VBOOT_VBNV_CMOS_BACKUP_TO_FLASH config VBOOT_STARTS_BEFORE_BOOTBLOCK def_bool n depends on VBOOT select ARCH_VERSTAGE_ARMV7 help Runs verstage on the PSP. Only available on certain ChromeOS branded parts from AMD. config VBOOT_HASH_BLOCK_SIZE hex default 0x9000 depends on VBOOT_STARTS_BEFORE_BOOTBLOCK help Because the bulk of the time in psp_verstage to hash the RO cbfs is spent in the overhead of doing svc calls, increasing the hash block size significantly cuts the verstage hashing time as seen below. 4k takes 180ms 16k takes 44ms 32k takes 33.7ms 36k takes 32.5ms There's actually still room for an even bigger stack, but we've reached a point of diminishing returns. config CMOS_RECOVERY_BYTE hex default 0x51 depends on VBOOT_STARTS_BEFORE_BOOTBLOCK help If the workbuf is not passed from the PSP to coreboot, set the recovery flag and reboot. The PSP will read this byte, mark the recovery request in VBNV, and reset the system into recovery mode. This is the byte before the default first byte used by VBNV (0x26 + 0x0E - 1) if VBOOT_SLOTS_RW_AB && VBOOT_STARTS_BEFORE_BOOTBLOCK config RWA_REGION_ONLY string default "apu/amdfw_a" help Add a space-delimited list of filenames that should only be in the RW-A section. config RWB_REGION_ONLY string default "apu/amdfw_b" help Add a space-delimited list of filenames that should only be in the RW-B section. endif # VBOOT_SLOTS_RW_AB && VBOOT_STARTS_BEFORE_BOOTBLOCK endif # SOC_AMD_PICASSO