/* SPDX-License-Identifier: BSD-3-Clause */
/* coreboot UEFI PEI wrapper */

#ifndef PEI_DATA_H
#define PEI_DATA_H

#include <stdint.h>

typedef struct {
	uint16_t mode;                /* 0: Disable, 1: Enable, 2: Auto, 3: Smart Auto */
	uint16_t hs_port_switch_mask; /* 4 bit mask, 1: switchable, 0: not switchable  */
	uint16_t preboot_support;     /* 0: No xHCI preOS driver, 1: xHCI preOS driver */
	uint16_t xhci_streams;        /* 0: Disable, 1: Enable */
} pch_usb3_controller_settings;

typedef void (*tx_byte_func)(unsigned char byte);
#define PEI_VERSION 6

struct pei_data
{
	uint32_t pei_version;
	uint32_t mchbar;
	uint32_t dmibar;
	uint32_t epbar;
	uint32_t pciexbar;
	uint16_t smbusbar;
	uint32_t wdbbar;
	uint32_t wdbsize;
	uint32_t hpet_address;
	uint32_t rcba;
	uint32_t pmbase;
	uint32_t gpiobase;
	uint32_t thermalbase;
	uint32_t system_type; /* 0 Mobile, 1 Desktop/Server */
	uint32_t tseg_size;
	uint8_t spd_addresses[4];
	uint8_t ts_addresses[4];
	int boot_mode;
	int ec_present;
	int gbe_enable;
	/*
	 * 0 = leave channel enabled
	 * 1 = disable dimm 0 on channel
	 * 2 = disable dimm 1 on channel
	 * 3 = disable dimm 0+1 on channel
	 */
	int dimm_channel0_disabled;
	int dimm_channel1_disabled;
	/* Seed values saved in CMOS */
	uint32_t scrambler_seed;
	uint32_t scrambler_seed_s3;
	/* Data read from flash and passed into MRC */
	uint32_t mrc_input_ptr;
	unsigned int mrc_input_len;
	/* Data from MRC that should be saved to flash */
	uint32_t mrc_output_ptr;
	unsigned int mrc_output_len;
	/*
	 * Max frequency DDR3 could be ran at. Could be one of four values:
	 * 800, 1067, 1333, 1600
	 */
	uint32_t max_ddr3_freq;
	/*
	 * USB Port Configuration:
	 *  [0] = enable
	 *  [1] = overcurrent pin
	 *  [2] = length
	 *
	 * Ports 0-7  can be mapped to OC0-OC3
	 * Ports 8-13 can be mapped to OC4-OC7
	 *
	 * Port Length
	 *  MOBILE:
	 *   < 0x050 = Setting 1 (back panel,           1 to  5 in, lowest  tx amplitude)
	 *   < 0x140 = Setting 2 (back panel,           5 to 14 in, highest tx amplitude)
	 *  DESKTOP:
	 *   < 0x080 = Setting 1 (front/back panel, less than 8 in, lowest  tx amplitude)
	 *   < 0x130 = Setting 2 (back panel,           8 to 13 in, higher  tx amplitude)
	 *   < 0x150 = Setting 3 (back panel,          13 to 15 in, highest tx amplitude)
	 */
	uint16_t usb_port_config[16][3];
	/* See the usb3 struct above for details */
	pch_usb3_controller_settings usb3;
	/*
	 * SPD data array for onboard RAM. Note that spd_data [1..3] are ignored: instead,
	 * the "dimm_channel{0,1}_disabled" flag and the spd_addresses are used to determine
	 * which DIMMs should use the SPD from spd_data[0].
	 */
	uint8_t spd_data[4][256];
	/* 32 bit pointer to tx_byte_func */
	uint32_t tx_byte_ptr;

	int ddr3lv_support;
	/*
	 * pcie_init needs to be set to 1 to have the system agent initialize PCIe.
	 * Note: This should only be required if your system has Gen3 devices and
	 * it will increase your boot time by at least 100ms.
	 */
	int pcie_init;
	/*
	 * N mode functionality. Leave this setting at 0.
	 *
	 * 0: Auto
	 * 1: 1N
	 * 2: 2N
	 */
	int nmode;
	/*
	 * DDR refresh rate config. JEDEC Standard No.21-C Annex K allows for DIMM SPD data to
	 * specify whether double-rate is required for extended operating temperature range.
	 *
	 * 0: Enable double rate based upon temperature thresholds
	 * 1: Normal rate
	 * 2: Always enable double rate
	 */
	int ddr_refresh_rate_config;
} __packed;

#endif