chip soc/intel/alderlake
	# HACK: Limit PL4 to PL2 to prevent power-off when system is booted on
	# battery power. This seems to only happen with the i7 units.
	register "power_limits_config[ADL_P_282_442_482_28W_CORE]" = "{
		.tdp_pl1_override = 20,
		.tdp_pl2_override = 56,
		.tdp_pl4 = 56, // FIXME: Set to 65
	}"

	# GPE configuration
	register "pmc_gpe0_dw0" = "PMC_GPP_A"
	register "pmc_gpe0_dw1" = "PMC_GPP_R"
	register "pmc_gpe0_dw2" = "PMC_GPD"

	device domain 0 on
		subsystemid 0x1558 0x7716 inherit

		device ref pcie4_0 on
			# PCIe PEG0 x4, Clock 0 (SSD2)
			register "cpu_pcie_rp[CPU_RP(1)]" = "{
				.clk_src = 0,
				.clk_req = 0,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D14)" # SSD2_PWR_EN
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F20)" # M2_CPU_SSD2_RST#
				register "srcclk_pin" = "0" # SSD2_CLKREQ#
				device generic 0 on end
			end
		end
		device ref tcss_xhci on
			register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC_SKIP)"
			chip drivers/usb/acpi
				device ref tcss_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB3 TBT Type-C""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						device ref tcss_usb3_port1 on end
					end
				end
			end
		end
		device ref xhci on
			# USB2
			register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Motherboard
			register "usb2_ports[1]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Multi Board
			register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC_SKIP)" # J_TYPEC1 (USB 3.2 Gen 2)
			register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # Fingerprint
			register "usb2_ports[5]" = "USB2_PORT_TYPE_C(OC_SKIP)" # J_TYPEC2 (Thunderbolt)
			register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # Camera
			register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth
			# USB3
			register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A Motherboard
			register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # J_TYPEC1 CH1
			register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # J_TYPEC1 CH2
			# ACPI
			chip drivers/usb/acpi
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB2 UJ_USB1""
						register "type" = "UPC_TYPE_A"
						device ref usb2_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 J_USB3_1""
						register "type" = "UPC_TYPE_A"
						device ref usb2_port2 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 J_TYPEC1""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						device ref usb2_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Fingerprint""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port5 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 J_TYPEC2""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						device ref usb2_port6 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Camera""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port7 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port10 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 J_USB3_1""
						register "type" = "UPC_TYPE_A"
						device ref usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 J_TYPEC1 CH0""
						register "type" = "UPC_TYPE_A"
						device ref usb3_port2 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 J_TYPEC1 CH1""
						register "type" = "UPC_TYPE_A"
						device ref usb3_port3 on end
					end
				end
			end
		end
		device ref tcss_dma0 on
			chip drivers/intel/usb4/retimer
				register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
				use tcss_usb3_port1 as dfp[0].typec_port
				device generic 0 on end
			end
		end
		device ref pcie_rp5 on
			# PCIe RP#5 x1, Clock 2 (WLAN)
			register "pch_pcie_rp[PCH_RP(5)]" = "{
				.clk_src = 2,
				.clk_req = 2,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" # WLAN_EN
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B17)" # WLAN_RST#_R
				register "srcclk_pin" = "2" # WLAN_CLKREQ#
				device generic 0 on end
			end
		end
		device ref pcie_rp6 on
			# PCIe RP#6 x1, Clock 5 (CARD)
			register "pch_pcie_rp[PCH_RP(6)]" = "{
				.clk_src = 5,
				.clk_req = 5,
				.flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
			}"
		end
		device ref pcie_rp8 on
			# PCIe RP#8 x1, Clock 6 (GLAN)
			register "pch_pcie_rp[PCH_RP(8)]" = "{
				.clk_src = 6,
				.clk_req = 6,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
		end
		device ref pcie_rp9 on
			# PCIe RP#9 x4, Clock 4 (SSD1)
			register "pch_pcie_rp[PCH_RP(9)]" = "{
				.clk_src = 4,
				.clk_req = 4,
				.flags = PCIE_RP_LTR,
			}"
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D16)" # SSD1_PWR_EN
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B16)" # M2_SSD1_RST#
				register "srcclk_pin" = "4" # SSD1_CLKREQ#
				device generic 0 on end
			end
		end
		device ref pmc hidden
			chip drivers/intel/pmc_mux
				device generic 0 on
					chip drivers/intel/pmc_mux/conn
						# J_TYPEC2
						use usb2_port6 as usb2_port
						use tcss_usb3_port1 as usb3_port
						device generic 0 alias conn0 on end
					end
				end
			end
		end
	end
end