chip soc/intel/alderlake
	register "power_limits_config[ADL_P_282_482_28W_CORE]" = "{
		.tdp_pl1_override = 28,
		.tdp_pl2_override = 60,
		.tdp_pl4 = 90,
	}"

	# GPE configuration
	register "pmc_gpe0_dw0" = "PMC_GPP_A"
	register "pmc_gpe0_dw1" = "PMC_GPP_R"
	register "pmc_gpe0_dw2" = "PMC_GPD"

	device domain 0 on
		subsystemid 0x1558 0x4041 inherit

		device ref pcie4_0 on
			# PCIe PEG0 x4, Clock 0 (SSD1)
			register "cpu_pcie_rp[CPU_RP(1)]" = "{
				.clk_src = 0,
				.clk_req = 0,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D14)" # SSD1_PWR_EN
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F20)" # M2_SSD1_RST#
				register "srcclk_pin" = "0" # SSD1_CLKREQ#
				device generic 0 on end
			end
		end
		device ref tcss_xhci on
			register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC_SKIP)"
			chip drivers/usb/acpi
				device ref tcss_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB3 TBT Type-C""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						device ref tcss_usb3_port1 on end
					end
				end
			end
		end
		device ref tcss_dma0 on
			chip drivers/intel/usb4/retimer
				register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
				use tcss_usb3_port1 as dfp[0].typec_port
				device generic 0 on end
			end
		end
		device ref xhci on
			# USB2
			register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # J_USB3_2
			register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # J_TYPEC1
			register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # J_USB3_1
			register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # Fingerprint
			register "usb2_ports[5]" = "USB2_PORT_TYPE_C(OC_SKIP)" # J_TYPEC2
			register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # Camera
			register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth
			# USB3
			register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A
			register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A
			register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C
			# ACPI
			chip drivers/usb/acpi
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB2 J_USB3_2""
						register "type" = "UPC_TYPE_A"
						device ref usb2_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 J_TYPEC1""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						device ref usb2_port2 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 J_USB3_1""
						register "type" = "UPC_TYPE_A"
						device ref usb2_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Fingerprint""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port5 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 J_TYPEC2""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						device ref usb2_port6 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Camera""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port7 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port10 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 J_USB3_2""
						register "type" = "UPC_TYPE_A"
						device ref usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 J_USB3_1""
						register "type" = "UPC_TYPE_A"
						device ref usb3_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 J_TYPEC1""
						register "type" = "UPC_TYPE_A"
						device ref usb3_port4 on end
					end
				end
			end
		end
		device ref i2c0 on
			# Touchpad I2C bus
			register "serial_io_i2c_mode[PchSerialIoIndexI2C0]" = "PchSerialIoPci"
			chip drivers/i2c/hid
				register "generic.hid" = ""ELAN0412""
				register "generic.desc" = ""ELAN Touchpad""
				register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A17)"
				register "generic.detect" = "1"
				register "hid_desc_reg_offset" = "0x01"
				device i2c 15 on end
			end
			chip drivers/i2c/hid
				register "generic.hid" = ""FTCS1000""
				register "generic.desc" = ""FocalTech Touchpad""
				register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A17)"
				register "generic.detect" = "1"
				register "hid_desc_reg_offset" = "0x01"
				device i2c 38 on end
			end
		end
		device ref sata off end
		device ref pcie_rp5 on
			# PCIe RP#5 x1, Clock 2 (WLAN)
			register "pch_pcie_rp[PCH_RP(5)]" = "{
				.clk_src = 2,
				.clk_req = 2,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" # PCH_WLAN_EN
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B13)" # BUF_PLT_RST#
				register "srcclk_pin" = "2" # WLAN_CLKREQ#
				device generic 0 on end
			end
		end
		device ref pcie_rp9 on
			# PCIe RP#9 x1, Clock 5 (CARD)
			register "pch_pcie_rp[PCH_RP(9)]" = "{
				.clk_src = 5,
				.clk_req = 5,
				.flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
			}"
		end
		device ref pcie_rp10 on
			# PCIe RP#10 x1, Clock 6 (GLAN)
			register "pch_pcie_rp[PCH_RP(10)]" = "{
				.clk_src = 6,
				.clk_req = 6,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			chip soc/intel/common/block/pcie/rtd3
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F7)" # LAN_PLT_RST#
				register "srcclk_pin" = "6" # LAN_CLKREQ#
				device generic 0 on end
			end
		end
		device ref pmc hidden
			chip drivers/intel/pmc_mux
				device generic 0 on
					chip drivers/intel/pmc_mux/conn
						# J_TYPEC2
						use usb2_port6 as usb2_port
						use tcss_usb3_port1 as usb3_port
						device generic 0 alias conn0 on end
					end
				end
			end
		end
	end
end