/* SPDX-License-Identifier: GPL-2.0-only */

#include <bootblock_common.h>
#include <stdint.h>
#include <arch/io.h>
#include <device/pnp_ops.h>
#include <device/pci_ops.h>
#include <device/pci_def.h>
#include <option.h>
#include <northbridge/intel/i945/i945.h>
#include <southbridge/intel/i82801gx/i82801gx.h>
#include <superio/smsc/lpc47n227/lpc47n227.h>

/* Override the default lpc decode ranges */
void mainboard_lpc_decode(void)
{
	int lpt_en = 0;

	if (get_uint_option("lpt", 0))
		lpt_en = LPT_LPC_EN; /* enable LPT */

	pci_write_config16(PCI_DEV(0, 0x1f, 0), LPC_IO_DEC, 0x0007);

	pci_update_config16(PCI_DEV(0, 0x1f, 0), LPC_EN, ~LPT_LPC_EN, lpt_en);
}

/* This box has two superios, so enabling serial becomes slightly excessive.
 * We disable a lot of stuff to make sure that there are no conflicts between
 * the two. Also set up the GPIOs from the beginning. This is the "no schematic
 * but safe anyways" method.
 */

void bootblock_mainboard_early_init(void)
{
	const pnp_devfn_t dev = PNP_DEV(0x2e, 0x00);

	pnp_enter_conf_state(dev);
	pnp_write_config(dev, 0x01, 0x94); /* Extended Parport modes */
	pnp_write_config(dev, 0x02, 0x88); /* UART power on */
	pnp_write_config(dev, 0x03, 0x72); /* Floppy */
	pnp_write_config(dev, 0x04, 0x01); /* EPP + SPP */
	pnp_write_config(dev, 0x14, 0x03); /* Floppy */
	pnp_write_config(dev, 0x20, (0x3f0 >> 2)); /* Floppy */
	pnp_write_config(dev, 0x23, (0x378 >> 2)); /* PP base */
	pnp_write_config(dev, 0x24, (0x3f8 >> 2)); /* UART1 base */
	pnp_write_config(dev, 0x25, (0x2f8 >> 2)); /* UART2 base */
	pnp_write_config(dev, 0x26, (2 << 4) | 0); /* FDC + PP DMA */
	pnp_write_config(dev, 0x27, (6 << 4) | 7); /* FDC + PP DMA */
	pnp_write_config(dev, 0x28, (4 << 4) | 3); /* UART1,2 IRQ */
	/* These are the SMI status registers in the SIO: */
	pnp_write_config(dev, 0x30, (0x600 >> 4)); /* Runtime Register Block Base */

	pnp_write_config(dev, 0x31, 0x00); /* GPIO1 DIR */
	pnp_write_config(dev, 0x32, 0x00); /* GPIO1 POL */
	pnp_write_config(dev, 0x33, 0x40); /* GPIO2 DIR */
	pnp_write_config(dev, 0x34, 0x00); /* GPIO2 POL */
	pnp_write_config(dev, 0x35, 0xff); /* GPIO3 DIR */
	pnp_write_config(dev, 0x36, 0x00); /* GPIO3 POL */
	pnp_write_config(dev, 0x37, 0xe0); /* GPIO4 DIR */
	pnp_write_config(dev, 0x38, 0x00); /* GPIO4 POL */
	pnp_write_config(dev, 0x39, 0x80); /* GPIO4 POL */

	pnp_exit_conf_state(dev);
}

void mainboard_late_rcba_config(void)
{
	/* Device 1f interrupt pin register */
	RCBA32(D31IP) = 0x00042220;

	/* dev irq route register */
	RCBA16(D31IR) = 0x0232;
	RCBA16(D30IR) = 0x3246;
	RCBA16(D29IR) = 0x0237;
	RCBA16(D28IR) = 0x3201;
	RCBA16(D27IR) = 0x3216;

	/* Disable unused devices */
	RCBA32(FD) |= FD_INTLAN;
}

static void init_artec_dongle(void)
{
	/* Enable 4MB decoding */
	outb(0xf1, 0x88);
	outb(0xf4, 0x88);
}

void mainboard_pre_raminit_config(int s3_resume)
{
	init_artec_dongle();
}