uses HAVE_MP_TABLE uses HAVE_PIRQ_TABLE uses USE_FALLBACK_IMAGE uses HAVE_FALLBACK_BOOT uses HAVE_HARD_RESET uses HARD_RESET_BUS uses HARD_RESET_DEVICE uses HARD_RESET_FUNCTION uses IRQ_SLOT_COUNT uses HAVE_OPTION_TABLE uses CONFIG_MAX_CPUS uses CONFIG_IOAPIC uses CONFIG_SMP uses FALLBACK_SIZE uses ROM_SIZE uses ROM_SECTION_SIZE uses ROM_IMAGE_SIZE uses ROM_SECTION_SIZE uses ROM_SECTION_OFFSET uses CONFIG_ROM_STREAM uses CONFIG_ROM_STREAM_START uses PAYLOAD_SIZE uses _ROMBASE uses XIP_ROM_SIZE uses XIP_ROM_BASE uses STACK_SIZE uses HEAP_SIZE uses USE_OPTION_TABLE uses LB_CKS_RANGE_START uses LB_CKS_RANGE_END uses LB_CKS_LOC uses MAINBOARD_PART_NUMBER uses MAINBOARD_VENDOR ## ROM_SIZE is the size of boot ROM that this board will use. default ROM_SIZE=524288 ### ### Build options ### ## ## Build code for the fallback boot ## default HAVE_FALLBACK_BOOT=1 ## ## Build code to reset the motherboard from linuxBIOS ## default HAVE_HARD_RESET=1 default HARD_RESET_BUS=1 default HARD_RESET_DEVICE=4 default HARD_RESET_FUNCTION=0 ## ## Build code to export a programmable irq routing table ## default HAVE_PIRQ_TABLE=1 default IRQ_SLOT_COUNT=9 ## ## Build code to export an x86 MP table ## Useful for specifying IRQ routing values ## default HAVE_MP_TABLE=1 ## ## Build code to export a CMOS option table ## default HAVE_OPTION_TABLE=1 ## ## Move the default LinuxBIOS cmos range off of AMD RTC registers ## default LB_CKS_RANGE_START=49 default LB_CKS_RANGE_END=122 default LB_CKS_LOC=123 ## ## Build code for SMP support ## Only worry about 2 micro processors ## default CONFIG_SMP=1 default CONFIG_MAX_CPUS=2 ## ## Build code to setup a generic IOAPIC ## default CONFIG_IOAPIC=1 ## ## Clean up the motherboard id strings ## default MAINBOARD_PART_NUMBER="Khepri 2100" default MAINBOARD_VENDOR="Newisys" ### ### LinuxBIOS layout values ### ## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. default ROM_IMAGE_SIZE = 65536 ## ## Use a small 8K stack ## default STACK_SIZE=0x2000 ## ## Use a small 16K heap ## default HEAP_SIZE=0x4000 ## ## Only use the option table in a normal image ## default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE ## ## Compute the location and size of where this firmware image ## (linuxBIOS plus bootloader) will live in the boot rom chip. ## if USE_FALLBACK_IMAGE default ROM_SECTION_SIZE = FALLBACK_SIZE default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) else default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) default ROM_SECTION_OFFSET = 0 end ## ## Compute the start location and size size of ## The linuxBIOS bootloader. ## default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) default CONFIG_ROM_STREAM = 1 ## ## Compute where this copy of linuxBIOS will start in the boot rom ## default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) ## ## Compute a range of ROM that can cached to speed up linuxBIOS, ## execution speed. ## ## XIP_ROM_SIZE must be a power of 2. ## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE ## default XIP_ROM_SIZE=65536 default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) ## ## Set all of the defaults for an x86 architecture ## arch i386 end #cpu k8 end ## ## Build the objects we have code for in this directory. ## driver mainboard.o if HAVE_MP_TABLE object mptable.o end if HAVE_PIRQ_TABLE object irq_tables.o end dir /drivers/trident/blade3d ## ## Romcc output ## makerule ./failover.E depends "$(MAINBOARD)/failover.c" action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E" end makerule ./failover.inc depends "./failover.E ./romcc" action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E" end makerule ./auto.E depends "$(MAINBOARD)/auto.c option_table.h" action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E" end makerule ./auto.inc depends "./auto.E ./romcc" action "./romcc -mcpu=k8 -O2 ./auto.E > auto.inc" end ## ## Build our 16 bit and 32 bit linuxBIOS entry code ## mainboardinit cpu/i386/entry16.inc mainboardinit cpu/i386/entry32.inc mainboardinit cpu/i386/bist32.inc ldscript /cpu/i386/entry16.lds ldscript /cpu/i386/entry32.lds ## ## Build our reset vector (This is where linuxBIOS is entered) ## if USE_FALLBACK_IMAGE mainboardinit cpu/i386/reset16.inc ldscript /cpu/i386/reset16.lds else mainboardinit cpu/i386/reset32.inc ldscript /cpu/i386/reset32.lds end ### Should this be in the northbridge code? mainboardinit arch/i386/lib/cpu_reset.inc ## ## Include an id string (For safe flashing) ## mainboardinit arch/i386/lib/id.inc ldscript /arch/i386/lib/id.lds ## ## Setup our mtrrs ## mainboardinit cpu/k8/earlymtrr.inc ### ### This is the early phase of linuxBIOS startup ### Things are delicate and we test to see if we should ### failover to another image. ### if USE_FALLBACK_IMAGE ldscript /arch/i386/lib/failover.lds mainboardinit ./failover.inc end ### ### O.k. We aren't just an intermediary anymore! ### ## ## Setup RAM ## mainboardinit cpu/k8/enable_mmx_sse.inc mainboardinit ./auto.inc mainboardinit cpu/k8/disable_mmx_sse.inc ## ## Include the secondary Configuration files ## dir /pc80 config chip.h northbridge amd/amdk8 "mc0" pci 0:18.0 pci 0:18.0 pci 0:18.0 pci 0:18.1 pci 0:18.2 pci 0:18.3 southbridge amd/amd8131 "amd8131" link 1 pci 0:0.0 pci 0:0.1 pci 0:1.0 pci 0:1.1 end southbridge amd/amd8111 "amd8111" link 1 pci 0:0.0 pci 0:1.0 on pci 0:1.1 on pci 0:1.2 on pci 0:1.3 on pci 0:1.5 on pci 0:1.6 on pci 1:0.0 on pci 1:0.1 on pci 1:0.2 on pci 1:1.0 on superio NSC/pc87360 link 1 pnp 2e.0 off # Floppy io 0x60 = 0x3f0 irq 0x70 = 6 drq 0x74 = 2 pnp 2e.1 off # Parallel Port io 0x60 = 0x378 irq 0x70 = 7 pnp 2e.2 off # Com 2 io 0x60 = 0x2f8 irq 0x70 = 3 pnp 2e.3 on # Com 1 io 0x60 = 0x3f8 irq 0x70 = 4 pnp 2e.4 off # SWC pnp 2e.5 off # Mouse pnp 2e.6 on # Keyboard io 0x60 = 0x60 io 0x62 = 0x64 irq 0x70 = 1 pnp 2e.7 off # GPIO pnp 2e.8 off # ACB pnp 2e.9 off # FSCM pnp 2e.a off # WDT end end end northbridge amd/amdk8 "mc1" pci 0:19.0 pci 0:19.0 pci 0:19.0 pci 0:19.1 pci 0:19.2 pci 0:19.3 end cpu k8 "cpu0" register "ldt1" = "{ .chip = &amd8131, .ht_width=16, .ht_speed=600 }" end cpu k8 "cpu1" end ## ## Include the old serial code for those few places that still need it. ## mainboardinit pc80/serial.inc mainboardinit arch/i386/lib/console.inc mainboardinit cpu/i386/bist32_fail.inc