chip soc/intel/skylake # Enable deep Sx states register "deep_s3_enable_ac" = "0" register "deep_s3_enable_dc" = "0" register "deep_s5_enable_ac" = "1" register "deep_s5_enable_dc" = "1" register "deep_sx_config" = "DSX_EN_WAKE_PIN" register "eist_enable" = "1" register "serirq_mode" = "SERIRQ_CONTINUOUS" # Set the Thermal Control Circuit (TCC) activation value to 95C # even though FSP integration guide says to set it to 100C for SKL-U # (offset at 0), because when the TCC activates at 100C, the CPU # will have already shut itself down from overheating protection. register "tcc_offset" = "5" # TCC of 95C # GPE configuration # Note that GPE events called out in ASL code rely on this # route. i.e. If this route changes then the affected GPE # offset bits also need to be changed. register "gpe0_dw0" = "GPP_C" register "gpe0_dw1" = "GPP_D" register "gpe0_dw2" = "GPP_E" register "gen1_dec" = "0x007c0a01" # EC 0xa00-0xa7f register "gen2_dec" = "0x000c03e1" # COM3 port 0x3e0 - 0x3ef register "gen3_dec" = "0x00fc02e1" # COM2/4/5/6 ports 0x2e0 - 0x2ff register "gen4_dec" = "0x000c0081" # 0x80 - 0x8f # Disable DPTF register "dptf_enable" = "0" # FSP Configuration register "ProbelessTrace" = "0" register "SataSalpSupport" = "0" register "SataMode" = "0" register "SataPortsEnable[0]" = "1" register "SataPortsEnable[1]" = "1" register "SataPortsEnable[2]" = "1" register "SataPortsDevSlp[0]" = "0" register "SataPortsDevSlp[1]" = "0" register "SataPortsDevSlp[2]" = "0" register "SataSpeedLimit" = "2" register "DspEnable" = "1" register "IoBufferOwnership" = "0" register "SsicPortEnable" = "0" register "ScsEmmcHs400Enabled" = "0" register "SkipExtGfxScan" = "1" register "HeciEnabled" = "1" register "SaGv" = "SaGv_Enabled" register "PmConfigSlpS3MinAssert" = "2" # 50ms register "PmConfigSlpS4MinAssert" = "1" # 1s register "PmConfigSlpSusMinAssert" = "3" # 500ms register "PmConfigSlpAMinAssert" = "3" # 2s register "PmTimerDisabled" = "1" # VR Settings Configuration for 4 Domains #+----------------+-------+-------+-------------+-------+ #| Domain/Setting | SA | IA | GT-Unsliced | GT | #+----------------+-------+-------+-------------+-------+ #| Psi1Threshold | 20A | 20A | 20A | 20A | #| Psi2Threshold | 4A | 5A | 5A | 5A | #| Psi3Threshold | 1A | 1A | 1A | 1A | #| Psi3Enable | 1 | 1 | 1 | 1 | #| Psi4Enable | 1 | 1 | 1 | 1 | #| ImonSlope | 0 | 0 | 0 | 0 | #| ImonOffset | 0 | 0 | 0 | 0 | #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | #+----------------+-------+-------+-------------+-------+ register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ .vr_config_enable = 1, .psi1threshold = VR_CFG_AMP(20), .psi2threshold = VR_CFG_AMP(4), .psi3threshold = VR_CFG_AMP(1), .psi3enable = 1, .psi4enable = 1, .imon_slope = 0x0, .imon_offset = 0x0, .voltage_limit = 1520, }" register "domain_vr_config[VR_IA_CORE]" = "{ .vr_config_enable = 1, .psi1threshold = VR_CFG_AMP(20), .psi2threshold = VR_CFG_AMP(5), .psi3threshold = VR_CFG_AMP(1), .psi3enable = 1, .psi4enable = 1, .imon_slope = 0x0, .imon_offset = 0x0, .voltage_limit = 1520, }" register "domain_vr_config[VR_GT_UNSLICED]" = "{ .vr_config_enable = 1, .psi1threshold = VR_CFG_AMP(20), .psi2threshold = VR_CFG_AMP(5), .psi3threshold = VR_CFG_AMP(1), .psi3enable = 1, .psi4enable = 1, .imon_slope = 0x0, .imon_offset = 0x0, .voltage_limit = 1520, }" register "domain_vr_config[VR_GT_SLICED]" = "{ .vr_config_enable = 1, .psi1threshold = VR_CFG_AMP(20), .psi2threshold = VR_CFG_AMP(5), .psi3threshold = VR_CFG_AMP(1), .psi3enable = 1, .psi4enable = 1, .imon_slope = 0x0, .imon_offset = 0x0, .voltage_limit = 1520, }" register "PcieRpEnable[2]" = "1" register "PcieRpEnable[3]" = "1" register "PcieRpEnable[4]" = "1" register "PcieRpEnable[8]" = "1" register "PcieRpEnable[9]" = "1" register "PcieRpEnable[10]" = "1" register "PcieRpEnable[11]" = "1" register "PcieRpClkSrcNumber[0]" = "0" register "PcieRpClkSrcNumber[3]" = "1" register "PcieRpClkSrcNumber[4]" = "2" register "PcieRpClkSrcNumber[8]" = "3" register "PcieRpClkSrcNumber[9]" = "3" register "PcieRpClkSrcNumber[10]" = "3" register "PcieRpClkSrcNumber[11]" = "3" register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port (right) register "usb2_ports[1]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port (right) register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # WiFi register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # F_USB3 header register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # F_USB3 header register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port (left) register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port (left) register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # GL850G for F_USB1 and F_USB2 headers register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A Port (right) register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A Port (right) register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # F_USB3 header register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # F_USB3 header # PL2 override 25W register "power_limits_config" = "{ .tdp_pl2_override = 25, }" # Send an extra VR mailbox command for the PS4 exit issue register "SendVrMbxCmd" = "2" # Lock Down register "common_soc_config" = "{ .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, }" device cpu_cluster 0 on device lapic 0 on end end device domain 0 on device pci 00.0 on end # Host Bridge device pci 02.0 on end # Integrated Graphics Device device pci 04.0 on end # SA thermal subsystem device pci 14.0 on end # USB xHCI device pci 14.1 on end # USB xDCI (OTG) device pci 14.2 on end # Thermal Subsystem device pci 14.3 off end # Camera device pci 16.0 on end # Management Engine Interface 1 device pci 16.1 off end # Management Engine Interface 2 device pci 16.2 off end # Management Engine IDE-R device pci 16.3 off end # Management Engine KT Redirection device pci 16.4 off end # Management Engine Interface 3 device pci 17.0 on end # SATA device pci 1c.0 off end # PCI Express Port 1 device pci 1c.1 off end # PCI Express Port 2 device pci 1c.2 on end # PCI Express Port 3 device pci 1c.3 off end # PCI Express Port 4 device pci 1c.4 on # PCI Express Port 5 smbios_slot_desc "SlotTypePciExpressMini52pinWithoutBSKO" "SlotLengthOther" "MPCIE_WIFI1" "SlotDataBusWidth1X" end device pci 1c.5 on end # PCI Express Port 6 device pci 1c.6 off end # PCI Express Port 7 device pci 1c.7 off end # PCI Express Port 8 device pci 1d.0 on # PCI Express Port 9 smbios_slot_desc "SlotTypeM2Socket3" "SlotLengthOther" "SSD_M.2 2242/2280" "SlotDataBusWidth4X" end device pci 1d.1 on end # PCI Express Port 10 device pci 1d.2 on end # PCI Express Port 11 device pci 1d.3 on end # PCI Express Port 12 device pci 1e.6 off end # SDXC device pci 1f.0 on chip drivers/pc80/tpm device pnp 0c31.0 on end end chip superio/ite/it8786e register "TMPIN1.mode" = "THERMAL_PECI" register "TMPIN1.offset" = "100" register "TMPIN1.min" = "128" register "TMPIN2.mode" = "THERMAL_RESISTOR" register "TMPIN2.min" = "128" register "TMPIN3.mode" = "THERMAL_MODE_DISABLED" register "ec.vin_mask" = "VIN_ALL" # FAN1 is CPU fan (on board) register "FAN1.mode" = "FAN_SMART_AUTOMATIC" register "FAN1.smart.tmpin" = " 1" register "FAN1.smart.tmp_off" = "35" register "FAN1.smart.tmp_start" = "60" register "FAN1.smart.tmp_full" = "85" register "FAN1.smart.tmp_delta" = " 2" register "FAN1.smart.pwm_start" = "20" register "FAN1.smart.slope" = "24" # FAN2 is system fan (4 pin connector populated) #register "FAN2.mode" = "FAN_MODE_OFF" # FAN3 PWM is used for LVDS backlight control #register "FAN3.mode" = "FAN_MODE_OFF" device pnp 2e.1 on # COM 1 io 0x60 = 0x3f8 irq 0x70 = 4 end device pnp 2e.2 on # COM 2 io 0x60 = 0x2f8 irq 0x70 = 3 end device pnp 2e.3 on # Printer Port io 0x60 = 0x378 io 0x62 = 0x778 irq 0x70 = 5 drq 0x74 = 3 end device pnp 2e.4 on # Environment Controller io 0x60 = 0xa40 io 0x62 = 0xa30 irq 0x70 = 9 end device pnp 2e.5 on # Keyboard io 0x60 = 0x60 io 0x62 = 0x64 irq 0x70 = 1 end device pnp 2e.6 on # Mouse irq 0x70 = 12 end device pnp 2e.7 off # GPIO end device pnp 2e.8 on # COM 3 io 0x60 = 0x3e8 irq 0x70 = 3 end device pnp 2e.9 on # COM 4 io 0x60 = 0x2e8 irq 0x70 = 4 end device pnp 2e.a off end # CIR device pnp 2e.b on # COM 5 io 0x60 = 0x2f0 irq 0x70 = 3 end device pnp 2e.c on # COM 6 io 0x60 = 0x2e0 irq 0x70 = 4 end end end # LPC Interface device pci 1f.1 on end # P2SB device pci 1f.2 on end # Power Management Controller device pci 1f.3 on end # Intel HDA device pci 1f.4 on end # SMBus device pci 1f.5 on end # PCH SPI device pci 1f.6 off end # GbE end end