#
#
#
# SPDX-License-Identifier: GPL-2.0-only

chip northbridge/amd/agesa/family14/root_complex
	device cpu_cluster 0 on
		chip cpu/amd/agesa/family14
			device lapic 0 on end
		end
	end
	device domain 0 on
		subsystemid 0x1022 0x1510 inherit
		chip northbridge/amd/agesa/family14
			device pci 0.0 on end # Root Complex
			device pci 1.0 on end # Internal Graphics P2P bridge 0x980[2456]
			device pci 4.0 on end # PCIE P2P bridge PCIe slot
			device pci 5.0 off end # PCIE P2P bridge
			device pci 6.0 on end # GbE MAC: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 (10ec:8168)
			device pci 7.0 off end # PCIE P2P bridge
			device pci 8.0 off end # NB/SB Link P2P bridge
		end # agesa northbridge

		chip southbridge/amd/cimx/sb800
			device pci 11.0 on end # SATA
			device pci 12.0 on end # OHCI USB 0-4
			device pci 12.2 on end # EHCI USB 0-4
			device pci 13.0 on end # OHCI USB 5-9
			device pci 13.2 on end # EHCI USB 5-9
			device pci 14.0 on end # SM
			device pci 14.1 off end # IDE	0x439c
			device pci 14.2 on end # HDA	0x4383
			device pci 14.3 on # LPC		0x439d
				chip superio/fintek/f71869ad
					register "multi_function_register_1" = "0x01"
					register "multi_function_register_2" = "0x6f"
					register "multi_function_register_3" = "0x24"
					register "multi_function_register_4" = "0x00"
					register "multi_function_register_5" = "0x60"
# HWM configuration registers
					register "hwm_smbus_address" = "0x98"
					register "hwm_smbus_control_reg" = "0x02"
					register "hwm_fan_type_sel_reg" = "0x00"
					register "hwm_fan1_temp_adj_rate_reg" = "0x33"
					register "hwm_fan_mode_sel_reg" = "0x07"
					register "hwm_fan1_idx_rpm_mode" = "0x0e"
					register "hwm_fan1_seg1_speed_count" = "0xff"
					register "hwm_fan1_seg2_speed_count" = "0x0e"
					register "hwm_fan1_seg3_speed_count" = "0x07"
					register "hwm_fan1_temp_map_sel" = "0x8c"
					register "hwm_temp_sensor_type" = "0x0E"	# default value
#
# XXX: 4e is the default index port and .xy is the
# LDN indexing the pnp_info array found in the superio.c
# NB: Jetway board changes the default (0x4e) index port to (0x2e) by pin 124,
#     see page 18 from Fintek F71869 V1.1 datasheet.
					device pnp 2e.00 off		# Floppy
						io 0x60 = 0x3f0
						irq 0x70 = 6
						drq 0x74 = 2
					end
					device pnp 2e.01 on			# COM1
						io 0x60 = 0x3f8
						irq 0x70 = 4
					end
# COM2 not physically wired on board.
					device pnp 2e.02 off		# COM2
						io 0x60 = 0x2f8
						irq 0x70 = 3
					end
					device pnp 2e.03 off		# Parallel Port
						io 0x60 = 0x378
						irq 0x70 = 7
						drq 0x74 = 3
					end
					device pnp 2e.04 on			# Hardware Monitor
						io 0x60 = 0x225 # Fintek datasheet says 0x295.
						irq 0x70 = 0
					end
					device pnp 2e.05 on # KBC
						io 0x60 = 0x060
						irq 0x70 = 1 # Keyboard IRQ
						irq 0x72 = 12 # Mouse IRQ
					end
					device pnp 2e.06 off end	# GPIO
					device pnp 2e.07 on end	# WDT
					device pnp 2e.08 off end	# CIR
					device pnp 2e.0a on end	# PME
				end # f71869ad
			end #LPC
			device pci 14.4 on  end # PCIB 0x4384, NOTE: PCI interface pins shared with GPIO {GPIO 35:0}
			device pci 14.5 on end # OHCI FS/LS USB (0x4399)
			device pci 14.6 off end # Hudson-E1 GbE MAC: Broadcom BCM5785 (14E4:1699)
			device pci 15.0 on end # PCIe PortA (0x43a0) GbE MAC: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 (10ec:8168)
			device pci 15.1 on end # PCIe PortB
			device pci 15.2 off end # PCIe PortC
			device pci 15.3 off end # PCIe PortD
			device pci 16.0 on end # OHCI USB 10-13 (0x4397)
			device pci 16.2 on end # EHCI USB 10-13 (0x4396)
			register "gpp_configuration" = "4" # GPP_CFGMODE_X1111 - PortA-D on 15.0-3 are each x1 lanes.
			register "boot_switch_sata_ide" = "0"	# 0: boot from SATA. 1: IDE

		end	#southbridge/amd/cimx/sb800

		chip northbridge/amd/agesa/family14

			# These seem unnecessary
			device pci 18.0 on end
			device pci 18.1 on end
			device pci 18.2 on end
			device pci 18.3 on end
			device pci 18.4 on end
			device pci 18.5 on end
			device pci 18.6 on end
			device pci 18.7 on end

#
# TODO: Verify the proper SocketId/MemChannelId/DimmId addresses of the SPD
# with i2cdump tool.
# Notes:  0xa0=0x50*2, 0xa2=0x51*2.. 0x50-0x54 are usually RAM modules on the SMBus.
#
			register "spdAddrLookup" = "
			{
				{ {0xA0, 0xA2}, {0x00, 0x00}, }, // socket 0 - Channel 0 & 1 - 8-bit SPD addresses
				{ {0x00, 0x00}, {0x00, 0x00}, }, // socket 1 - Channel 0 & 1 - 8-bit SPD addresses
			}"

		end # agesa northbridge

	end #domain
end #northbridge/amd/agesa/family14/root_complex